Chain‐linked lactic acid polymers by benzene diisocyanate

Chain‐linked lactic acid polymers with high molecular weight were synthesized by two‐step polymerization method, including polycondensation and chain extending reactions. The effects of chain extender toluene diisocyanate (TDI) on the chain‐linked lactic acid polymers were studied. The polymers obtained were characterized by gel permeation chromatography, fourier transform infrared spectroscopy, ¹H NMR, and differential scanning calorimeter. Reactions between 1,4‐butanediol and lactic acid oligomers led to hydroxyl‐terminated prepolymer, which provided significant increase of molecular weight in the chain extending reaction. In addition, the glass transition temperature (T_g) and the melting temperature (T_m) were increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1045–1049, 2006     

Influence of melt stability on the crystallization of bis(4-aminophenoxy)benzene-oxydiphthalic anhydride based polyimides

Novel high performance semicrystalline polyimides, based on controlled molecular weight phthalic anhydride (PA) endcapped 1,4-bis(4-aminophenoxy)benzene (TPEQ diamine) and oxydiphthalic dianhydride (ODPA), were synthesized. They exhibited excellent thermal stability in nitrogen and air atmospheres as determined by thermogravimetric analysis (TGA). The glass transition temperatures (T_g) for these polymers ranged from 225°C for the 10,000 M_n (10K) polymer, to 238°C for the 30,000 (30K) M_n material. The observed melting temperatures for all the polymers were ∼420°C. The crystallization behavior of these polymers showed a strong molecular weight dependence, as illustrated by the observation that the 10K and 12.5K polymers crystallized with relative ease, whereas the 15K, 20K, and 30K polymers showed little or no ability to undergo thermal recrystallization. The thermal stability of these polymers above T_m was investigated by studying the effect of time and temperature in the melt on the cold crystallization and melting of these polymers. Increased time and temperature in the melt resulted in lower crystallinity because of melt state degradation, such as crosslinking and branching, as evidenced by an increase in melt viscosity, which was more prominent for the higher molecular weight polymers.     

SYNTHESIS,CHARACTERIZATION, AND THERMAL STABILITY OF HOMOPOLYMER AND COPOLYMER OF SOME 3-ARYL-2-HYDROXYPROPYL METHACRYLATES

Three new hydroxypropyl methacrylates having three different aryl rings were synthesized by addition of 2,3-epoxypropyl aromatic hydrocarbon to methacrylic acid. The monomers prepared are 3-phenyl-2-hydroxypropyl methacrylate, 3-tolyl-2-hydroxypropyl methacrylate, (THPMA), and 3-naphtyl-2-hydroxypropyl methacrylate. The homopolymers of these monomers and two different copolymers, [poly(THPMA-co-BMA)], were obtained from polymerization at 60°C in 1,4-dioxane solution using AIBN as initiator. All the monomers and the polymers were characterized by FT-IR and ¹H and ¹³C NMR techniques. Solubility parameters of the polymers and average molecular weight of poly(THPMA) were determined. Thermal stabilities of the polymers were given as comparing with each other by using TGA curves. Thermal degradation of poly(THPMA60%-co-BMA40%) was studied in detail.     

Polymers containing sulfur in the side chain

We synthesized new thiodicarboxylic acids, p-tolylmethylthiomethylsuccinic acid and 1-naphthylmethylthiomethylsuccinic acid, and thiodiols, 2-(p-tolylmethylthiomethyl)-1,4-butanediol and 2-(1-naphthylmethylthiomethyl)-1,4-butanediol, by the addition of dimethyl itaconate with p-tolylmethanethiol or 1-naphthylmethanethiol, followed by hydrolysis or reduction, respectively, of the resultant dimethyl esters. These difunctional monomers were used for the synthesis of new linear polyesters and polyurethanes containing sulfur in the side chain. The polyesters were synthesized by melt polycondensation of the obtained acids with 2,2′-oxydiethanol. We found reduced viscosity, molecular weight (by GPC), and softening temperature for the reaction products. Low molecular weights, low softening temperature, and very good solubility in organic solvents are their characteristics. The polyurethanes were prepared by polyaddition diols with hexamethylene diisocyanate and tolylene diisocyanate in benzene. They were characterized by reduced viscosity and some tensile properties. The polyurethane derived from 2-(p-tolylmethylthiomethyl)-1,4-butanediol and hexamethylene diisocyanate (η_red. 1.17 dL/g) behaves like a high elasticity thermoplastic elastomer. Thermal stability of all polymers was determined by thermogravimetric analysis. The structure of the monomers and polymers were confirmed by elemental analysis and FTIR and ¹H-NMR spectroscopy. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of biodegradable copolymers based on polyether oligomers and fatty diacids

Polyether oligomers (M_n = 200–2000) were respectively esterified by succinic anhydride and fatty sebacoyl chloride to synthesize corresponding intermediate diacids, and experimental results of melt polycondensations based on these two kinds of intermediates were compared. The reasons for affecting higher molecular weight products to be achieved in polymerization with prepolymers based on succinic anhydride esterification were theoretically analyzed. Light scattering measurements showed that copolyanhydrides with higher molecular weights exceeding 8 × 10⁴ (weight-average) were synthesized from the intermediate diacids prepared by a new method using fatty diacid chlorides to undergo esterification with polyether. Synthesized intermediates were characterized by ¹H-NMR and infrared spectroscopy. Intrinsic viscosity of the polymers were measured to display the advancement of polymerization. The properties of polymers were investigated by X-ray diffraction and differential scanning calorimetry analysis as well. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1891–1898, 1997     

Poly(1,4‐cyclohexylenedimethylene‐1, 4‐cyclohexanedicarboxylate): analysis of parameters affecting polymerization and cis–trans isomerization

Weatherable semicrystalline polyesters based on 1,4‐cyclohexanedimethanol, 1,4‐cyclohexanedicarboxylic acid (CHDA) or dimethyl 1,4‐cyclohexane dicarboxylate (DMCD) can be prepared under normal melt‐phase conditions, using titanium tetrabutoxide as catalyst. The effect of monomer ratio, reaction temperature and catalyst loading on the final polymer properties was studied. Under the proper polymerization conditions, poly(1,4‐cyclohexylenedimethylene‐1,4‐cyclohexanedicarboxylate) polymers with high molecular weight can be obtained. During polymerization, isomerization can occur towards the thermodynamically stable cis‐trans ratio of 34–66 mol%. Carboxylic acid end groups can catalyze the isomerization and therefore the polymerization is more critical starting from CHDA rather than DMCD. Moreover, temperature control becomes a key factor to avoid or to limit isomerization. The study of the isomerization of the different monomers permitted a better understanding of the isomerization and therefore of the polymerization process. Copyright © 2011 Society of Chemical Industry     

Polymerization of – Phenylmaleimide Initiated by 9-Borabicyclo[3.3.1]nonane

N-Phenylmaleimide (N-PMI) was polymerized by 9-borabicyclo[3.3.1] nonane (9-BBN) in tetrahydrofuran under argon at 0°C. The molecular weight distributions of the resulting polymers were around 1·1. The rate of poly-merization was proportional to [9-BBN]^1·18 and [N-PMI]^1·24. Hydroquinone had little effect on the rate of polymerization and on the molecular weight of the polymers obtained. Triethylamine completely inhibited the polymerization, and aniline with a relatively small pK_a value and zinc iodide effectively retarded the polymerization. The polymerization did not proceed either in polar dimethylformamide or in non-polar toluene. In polymerizations at temperatures higher than 60°C the conversions decreased. On the basis of the results, a non-radical mechanism was proposed for this polymerization. © of SCI.     

Catalyzed chain extension of poly(butylene adipate) and poly(butylene succinate) with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline)

Low‐molecular‐weight HOOC‐terminated poly(butylene adipate) prepolymer (PrePBA) and poly(butylene succinate) prepolymer (PrePBS) were synthesized through melt‐condensation polymerization from adipic acid or succinic acid with butanediol. The catalyzed chain extension of these prepolymers was carried out at 180–220°C with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) as a chain extender and p‐toluenesulfonic acid (p‐TSA) as a catalyst. Higher molecular weight polyesters were obtained from the catalyzed chain extension than from the noncatalyzed one. However, an improperly high amount of p‐TSA and a high temperature caused branching or a crosslinking reaction. Under optimal conditions, chain‐extended poly(butylene adipate) (PBA) with a number‐average molecular weight up to 29,600 and poly(butylene succinate) (PBS) with an intrinsic viscosity of 0.82 dL/g were synthesized. The chain‐extended polyesters were characterized by IR spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray scattering, and tensile testing. DSC, wide‐angle X‐ray scattering, and thermogravimetric analysis characterization showed that the chain‐extended PBA and PBS had lower melting temperatures and crystallinities and slower crystallization rates and were less thermally stable than PrePBA and PrePBS. This deterioration of their properties was not harmful enough to impair their thermal processing properties and should not prevent them from being used as biodegradable thermoplastics. The tensile strength of the chain‐extended PBS was about 31.05 MPa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Characterization of poly(3,3-bisethoxymethyl oxetane) and poly(3,3-bisazidomethyl oxetane) and their block copolymers

The homopolymers, poly(3,3-bisethoxymethyl oxetane) (polyBEMO), poly(3,3-bisazidomethyl oxetane) (polyBAMO), and triblock copolymers based on these homopolymers and a statistical copolymer center block composed of BAMO and 3-azidomethyl-3-methyl oxetane AMMO were synthesized and characterized by differential scanning calorimetry, modulus-temperature, optical microscopy, membrane osmometry, and solution and melt viscosity. The values of K and a for the Mark-Houwink equation were found to be 7.29 × 10^?3 mL/g and 0.80, respectively, for polyBEMO at 25°C using number-average molecular weights. Glass transition temperatures were in the range ?25 to ?40°C and melting temperatures were between 65 and 90°C for all polymers. The melting temperature was found to increase as expected with molecular weight. Melt viscosities of triblock copolymers with polyBAMO end blocks were at least an order of magnitude lower than those with polyBEMO end blocks and clear optically, suggesting that the polyBAMO-based triblock copolymers formed one phase in the melt, while the polyBEMO-based triblock materials (milk white) phase separated. The addition of filler raised the melt viscosity to a level between that predicted by the Guth-Smallwood and the Mooney equations.     

TiCl4 immobilized on a composite support SiO2/MgCl2·x(1,4-butanediol)/poly[styrene-co-(acrylic acid)] for ethylene polymerization: The barrier effect of poly[styrene-co-(acrylic acid)]

By immobilizing titanium-based Ziegler–Natta catalyst on composite support, SiO₂/MgCl₂·x(1,4-butanediol)/poly[styrene-co-(acrylic acid)] (SiO₂/MgCl₂·xBD/PSA) and SiO₂/MgCl₂·xBD/PSA/TiCl₄ (SMPT) were synthesized for ethylene polymerization. SiO₂/MgCl₂·xBD/TiCl₄ without PSA was also prepared for comparison. The results of energy-dispersive X-ray analysis, SEM, and thermogravimetric analysis demonstrated that SMPT had a unique core-mantle-shell structure. The PSA layer can be considered as a barrier for the mass-transfer of reactants based on the results of self-diffusion measurement by pulsed field gradient NMR and ethylene polymerization. The polyethylene produced by SMPT showed high molecular weight (MW) and broad molecular weight distribution (MWD). The influences of PSA content, hydrogen, and comonomer on the ethylene polymerization behavior were also investigated. The results further demonstrated that the PSA layer in the composite support had different diffusion capabilities to the reactants. The physical properties of the produced polyethylene implied the possibility to control the MW and MWD of polyethylene by the manipulation of PSA layer. The catalyst fragmentation during ethylene polymerization was also affected by the PSA shell due to its barrier effect. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of tetrahydrofuran as a structure modifier in preparation of SBS thermoplastic block copolymers in cyclohexane

Linear styrene-butadiene block copolymers of polyA-block-polyB-block-polyA type (SBS) were synthesized in the presence of varying amounts of THF functioning as the polar structure modifier. The efficiency of this modifier was studied by analyzing the microstructure of synthesized polymers using ¹³C-NMR, and the effect of THF on polymerization kinetics was determined by progressive buildup of the molecular weight measured by GPC. Polymerization at 4000 ppm THF concentration resulted in the highest styrene polymerization rate while a 1 wt % concentration gave the highest butadiene polymerization rate. The vinyl content increased from 20 to 64% with an increase in the amount of THF from 200 ppm to 1 wt % while the content of trans-1,4 and cis-1,4 units decreased. For SBS polymer synthesized via a sequential process, the use of THF as the structure modifier enhanced the crossover efficiency that would otherwise result in a skewed molecular weight distribution with a higher polydispersity. For SBS polymer made via a coupling process, the coupling efficiency decreased when the amount of THF exceeded a certain limit. The temperature dependence of the coupling efficiency was also investigated. © 1996 John Wiley & Sons, Inc.     

Synthesis and properties of styrene copolymers. Preparation of film‐modified electrodes to detect Pb2+ ions

Organic solvent‐soluble polymers containing different functional groups able to coordinate metal ions from low concentration were synthesized to build complexing polymer film modified electrodes. Poly(acetamide acrylic acid‐co‐styrene) and poly(itaconic acid‐co‐styrene) were synthesized by radical polymerization. The copolymers were characterized by Fourier transform infrared and ¹H NMR spectroscopy, electron scanning microscopy, and thermal analysis. The molecular weight and molecular weight distribution were determined by size exclusion chromatography. These complexing polymers have been used in the preparation of complexing modified electrodes (CME) by spin coating. The CME have been tested for the detection of metal ions using the chemical preconcentration‐anodic stripping technique. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2380–2385, 2006     

Effects of molecular weight on dual light‐ and thermo‐responsive behaviors of homopolymers with azobenzene units and terminal oligo(ethylene glycol) units

A series of water‐soluble dual light‐ and thermo‐responsive homopolymers bearing azobenzene units and terminal oligo(ethylene glycol) units with well‐defined molecular weight (M _n = 0.69 × 10⁴ to 4.60 × 10⁴ g mol^?1) were synthesized via reversible addition–fragmentation chain transfer polymerization. All the homopolymers exhibited reversible photoisomerization and their lower critical solution temperatures showed an unusual increase with increasing molecular weight. Interestingly, by increasing the molecular weight, the aggregate morphology of these polymers was found to evolve from a spherical to a cylindrical shape. © 2017 Society of Chemical Industry     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Studies on the preparation of branched polymers from styrene and divinylbenzene

The self‐condensing vinyl polymerization of styrene and an inimer formed in situ by atom transfer radical addition from divinylbenzene and 2‐bromoisobutyl‐tert‐butyrate using atom transfer radical polymerization technique was studied. To study the polymerization mechanism and achieve high molecular weight polymer in a high polymer yield, the polymerization was carried out in bulk at 80°C. Proton nuclear magnetic resonance (¹H‐NMR) spectroscopy and gel permeation chromatography (GPC) coupled with multiangle laser light scattering (MALLS) were used to monitor the polymerization process and characterize the solid polymers. It is proved that the polymerization shows a “living” polymerization behavior and the crosslinking reaction has been restrained effectively due to the introduction of styrene. Polymers with high molecular weight (M_w.MALLS > 10⁵) can be prepared in high yield (near 80%). Comparison of the apparent molecular weights measured by GPC with the absolute values measured by MALLS indicates the existence of branched structures in the prepared polymers. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and structure control of l‐lactic acid–glycolic acid copolymer by homo‐copolymerization

A two‐step direct melt copolymerization process of l ‐lactic acid (L ‐LA)/glycolic acid (GA) was developed: poly(l ‐lactic acid) (PLLA) and poly(glycolic acid) (PGA) with different molecular weight was first synthesized respectively by binary catalyst (tin chloride/p‐toluenesulfonic or tin chloride); and then poly(l ‐lactic‐co‐glycolic acid) (b‐PLGA) was produced by melt polymerization of the as‐prepared PLLA and PGA, wherein the composition and chain structure of b‐PLGA copolymers could be controlled by the molecular weight of PLLA. The chain structure and thermal properties of copolymers were studied by Wide‐angle X‐ray diffraction, nuclear magnetic resonance, differential scanning calorimetry, and thermogravimetric analysis. In comparison with the random PLGA (r‐PLGA) synthesized by one‐step direct melt polymerization, the average l ‐lactic blocks length (L_LA) in b‐PLGA was longer while the average glycolic blocks length (L_GA) in b‐PLGA was shorter which further resulted in the improved crystallinity and thermostability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41566.     

Hydrolytic Degradation of Aliphatic Polyesters Copolymerized with Poly(ethylene glycol)s

Poly(1,4-butanediol succinate) copolymers were prepared by melt polycondensation of succinic acid and 1,4-butanediol with 10–50mol% (in feed) of poly(ethylene glycol) (PEG), where molecular weight (MW) of PEG is 200–2000. The reduced specific viscosity of the copolymers increased with incorporation of the PEG component, but a higher PEG content in the copolymers reduced it. The temperature of melting (T_m) and crystallinity decreased with increasing PEG content. T_m depression of the copolymers followed approximately Flory’s equation, suggesting that these are random type copolymers. Tensile strength and elongation decreased with increasing MW and content of PEG. The weight loss of copolymer films in a buffer solution with or without lipase at 37°C, as well as water absorption, increased with increasing PEG content, implying that higher water absorption contributes to hydrolytic degradation of the films. However, the weight loss of copolymers with PEG of lower MW increased greatly in spite of lower water absorption, demonstrating that hydrolytic degradation is influenced by the concentration of degradable ester linkages between succinic acid and PEG segments rather than water absorption. © of SCI.     

Study of chain sequence in the controlled radical telomerization of vinyl acetate with Co(acac)2 catalyst in bulk

A series of porphyrin-containing polymers with triazole rings as linkers have been successfully synthesized by click polymerization. The polycycloadditions of porphyrin-containing dialkyne 1 and 1,4-diazidobenzene 2 were initiated either by simple heating or by Cu(I)-catalyst, affording polymers P1-P8 with relatively high molecular weight. The polymerization process was monitored by gel permeation chromatography analysis. The polymer prepared by thermally initiated click polymerization has unimodal molecular weight distribution and moderate polydispersity index after prolonging reaction time to 170?h. Compared with the metal-free click polymerization, the rate of molecular weight growth in Cu(I)-catalyzed click polymerization declined, leading to relatively low molecular weight of the resulting polymer. The as-synthesized polymers are soluble in common organic solvents and stable at a temperature up to 350?°C. The photophysical properties of the porphyrin monomer and the polymer were investigated by UV?Cvis and fluorescence spectroscopy. This approach offers practical advantages over other synthetic methods used to prepare main-chain porphyrin-containing polymers with regard to the absence of byproducts generated during the polymerization reaction.     

Synthesis and characterization of polyamide resins from soy-based dimer acids and different amides

A series of soy-based polyamides with different dimer acids and diamines were synthesized using a condensation polymerization technique. The molecular weight of polyamides prepared from 1,4-phenylenediamine increases greatly with a reaction temperature above 260°C. The physical properties of the polyamides, such as glass transition temperature (T_g), melting point (T_m), decomposition temperature (T_d), crystalline behavior, and mechanical strength strongly depend on their molecular weight and flexibility of diamines used. The aromatic-based polyamides have a higher T_g, T_m, T_d, and stronger mechanical strength than that of aliphatic-based polyamides. X-ray diffraction patterns of the samples indicate that all of the resins synthesized present a typical semicrystalline morphology. Polyamides made from hydrogenated dimer acid possess lower T_g and higher mechanical strength, compared with polyamides from unsaturated dimer acid with different dimer and trimer ratios. These results are analyzed and discussed in accordance with the influence of rigid aromatic segments and the microstructure of different dimer acids. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68:305–314, 1998     

Improved dispersion of clay platelets in poly(butylene terephthalate) nanocomposite by ring‐opening polymerization of cyclic oligomers: Effect of the processing conditions and comparison with nanocomposites obtained by melt intercalation

Poly(butylene terephthalate) nanocomposites with organically modified montmorillonites have been prepared by in‐situ ring opening polymerization of PBT cyclic oligomers. High molecular weight polymers can be obtained by choosing the proper polymerization conditions and catalyst in very short polymerization time (10 min) and low temperature (205°C). A better dispersion of the clay and a consistently higher M_w have been obtained by this method respect to the standard melt intercalation approach, leading to improved thermo‐mechanical properties of the nanocomposite. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009