Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium-doped zinc oxide nanorods

Undoped and aluminium (Al)-doped zinc oxide (ZnO) nanorods have been synthesized by electrochemical route. The synthesized materials have been characterized by X-ray diffraction, UV–visible spectrometer and scanning electron microscope. The Al-doped ZnO nanorods have been coated with polyvinyl alcohol. Current–voltage characteristics have been investigated in dark and under UV-light illumination. Aluminium doping in ZnO increase its electrical conductivity and further polyvinyl alcohol coating on Al-doped ZnO increase UV sensitivity of the material. Response and recovery time of Al-doped ZnO and PVA-coated Al-doped ZnO nanorods have been recorded. PVA-coated Al-doped ZnO nanorods shows very fast response and recovery time of 10 s in comparison to uncoated ZnO (20 min) nanorods.     

Synthesis of ZnO nanorods from aqueous solution

In the present work, crystalline one-dimensional ZnO nanorods were synthesized by a PVP (polyvinylpyrrolidone)-assisted hydrothermal process with zinc acetate as the precursor. The major advantage of this technique is the use of water as the solvent: cheaper and more environmentally friendly than alcohol. The as-synthesized ZnO nanorods have diameters of 50-200 nm and lengths up to 5 μm. X-ray powder diffractometry (XRD), transmission electron microscopy (TEM) and selected area electron diffraction (SAED), Fourier transmission infrared spectroscopy (FTIR) were used to characterize the structural and the chemical features of the ZnO nanorods.     

Combination of surface texturing and nanostructure coating for reduction of light reflection in ZnO/Si heterojunction thin film solar cell

In this study, we report a single heterojunction solar cell based on n-type zinc oxide/p-type silicon. Three different solar cells were fabricated based on ZnO thin film on Si substrate, ZnO nanorods on Si substrate, and ZnO nanorods on micro-pyramidal structure of Si substrate. The comparison between these three kinds of solar cells was studied. Pyramidal structure of silicon was fabricated using chemical etching technique of p-type Si (100). The chemical solution consists of NaOH, isopropyl alcohol and hydrazine hydrate. The results showed that Si micro-pyramids can enhance optical absorption of Si substrates by increasing surface area and entrapping of incident light. For fabrication of uniform ZnO nanorods, a seed layer of ZnO was deposited on Si substrates via radio frequency magnetron sputtering technique. This layer can be used as an active n-type material in heterojunction solar cells as well. ZnO nanostructures can increase light absorption due to their high specific surface area. The combination of ZnO nanorods and Si micro-pyramids can enhance light trapping effect and increase the efficiency of solar cells. The structural and morphology of samples were studied using field-emission scanning electron microscopy, atomic force microscopy and X-ray diffractometry while the optical properties were investigated using photoluminescence and reflectance spectrometry. The efficiency and fill factor of solar cells were obtained from current–voltage characteristics using a solar simulator and a source-meter. The results showed that the efficiency of solar cell based on nanostructures of ZnO/micropyramids of Si is highly increased due to high anti-reflective behavior of this sample.     

Synthesis and Luminescent Properties of Planar-tip and Tapered-tip ZnO Nanorod Arrays

Vertically aligned ZnO nanorods were synthesized on a-plane sapphire via a metal catalyzed vapor phase transport and condensation process in a two-zone vacuum furnace. Planar-tip and tapered-tip ZnO nanorods were successfully synthesized by utilizing different source materials under the same growth conditions. The growth mechanisms were proposed to be vapor-liquid-solid （VLS） process for planar-tip ZnO nanorods and a combination of VLS and self-catalyzed processes for tapered-tip ZnO nanorods, From cathodoluminescence （CL） measurements, tapered-tip ZnO nanorods have more intense green emission than planar-tip ZnO nanorods, and therefore possess higher oxygen vacancy concentration than planar-tip ZnO nanorods. From CL characteristics, well-aligned planar-tip ZnO nanorods shall serve effectively as laser source, while well-aligned tapered-tip ZnO nanorods are suitable for direction-related optical applications.     

Effects of seed layers on structural, morphological, and optical properties of ZnO nanorods

We studied the effects of seed layers on the structural and optical properties of ZnO nanorods. ZnO and Ag-doped ZnO (ZnO:Ag) seed layers were deposited on glass substrates by magnetron co-sputtering. ZnO nanorods were grown on these seed layers by the chemical bath deposition in an aqueous solution of Zn(NO3)2 and hexamethyltetramine. SEM micrographs clearly reveal that ZnO nanorods were successfully grown on both kinds of seed layers. The XRD patterns indicate that crystallization of ZnO nanorods is along the c-axis. Meanwhile, the packing density and the vertical alignment of the ZnO nanorods on the ZnO seed layer are better than those of the ZnO nanorods on ZnO:Ag. The enhanced growth of nanorods is thought to be due to the fact that the ZnO layer exhibits a higher crystalline quality than the ZnO:Ag layer. According to the low-temperature photoluminescence spectra, the ZnO nanorods on the ZnO seed layer show a narrow strong ultraviolet emission band centered at 369 nm, while those on ZnO:Ag exhibit multiple bands. These results are thought to be related with the crystallinity of ZnO nanorods, the morphologies of ZnO nanorods, and the reflectivities of seed layers. More detailed studies for clarification of the seed layer effect on the growth of ZnO nanorods are desirable.     

Influence of post-annealing temperature on the material properties of zinc oxide nanorods

Zinc oxide (ZnO) is an emerging optoelectronic material in large area electronic applications due to its various functional behaviors. We present the fabrication and the characterization of ZnO nanorods. The ZnO nanorods were synthesized using sol-gel hydrothermal technique on oxidized silicon substrates. Different post-annealing temperatures were explored in the sol-gel hydrothermal synthesis of the ZnO nanorods. The surface morphology of the ZnO nanorods were examined using scanning electron microscope (SEM). In order to investigate the structural properties, the ZnO nanorods were measured using X-ray diffractometer (XRD). The optical properties were measured using ultraviolet-visible (UV-Vis) spectroscopy. The influence of the post-annealing temperature on the realized ZnO nanorods will be revealed and discussed in this paper.     

Effect of buffer layer thickness on the growth properties of hydrothermally grown ZnO nanorods

We investigated the effect of ZnO buffer layer thickness on the growth of hydrothermally grown ZnO nanorods. A series of ZnO buffer layers with different thicknesses was deposited on a p-Si (111) substrate using a co-sputtering system. After annealing the ZnO buffer layer, ZnO nanorods grown were grown hydrothermally at 95 degrees C. Unlike ZnO nanorods grown on as-deposited ZnO buffer layer, the diameter and length of ZnO nanorods grown on annealed ZnO buffer layers can be controlled. The structural and optical properties of ZnO nanorods grown on annealed ZnO buffer layers were analyzed by field-emission scanning electron microscopy, X-ray diffraction, and photoluminescence. The influence of ZnO buffer layer thickness on ZnO nanorods growth is discussed.     

Modulation of field emission properties of znO nanorods during arc discharge

Zinc oxide (ZnO) nanorods have been synthesized via the arc discharge method. Different oxygen partial pressures were applied in the arc discharge chamber to modulate the field emission properties of the as-synthesized ZnO nanorods. Scanning electron microscopy (SEM) was carried out to analyze the morphology of the ZnO nanorods. The ion beam analysis technique of proton induced X-ray emission (PIXE) was performed to probe the impurities in ZnO nanorods. SEM images clearly revealed the formation of randomly oriented ZnO nanorods with diameters between 10-50 nm. It was found that the morphology and the electrical properties of the ZnO nanorods were dependent on the oxygen partial pressure during arc discharge. In addition enhanced UV-sensitive photoconductivity was found for ZnO nanorods synthesized at high oxygen partial pressure during arc discharge. The field emission properties of the nanorods were studied. The turn-on field, which is defined at a current density of 10 microA cm(-2), was about 3 V microm(-1) for ZnO nanorods synthesized at 99% oxygen partial pressure during arc discharge. The turn-on field for ZnO nanorods increased with the decrease of oxygen partial pressure during arc discharge. The simplicity of the synthesis route coupled with the modulation of field emission properties due to the arc discharge method make the ZnO nanorods a promising candidate for a low cost and compact cold cathode material.     

Catalytic effects of ZnO nanorods grown by sonochemical decomposition of zinc acetate dihydrate

In this study, we prepared ZnO nanorods by a sonochemical method using a zinc acetate dihydrate as a new precursor. Well-aligned high-quality ZnO nanorods were synthesized on FTO glass by the sonochemical decomposition of zinc acetate dihydrate using a ZnO thin-film as the catalytic layer. The ZnO thin-films were deposited on the FTO glass by a sputtering method. To investigate their catalytic effects on the ZnO nanorods, catalytic ZnO thin-films of 20 nm, 40 nm, and 60 nm thickness were prepared by adjusting the sputtering time. The ZnO nanorods grown on catalytic layers with different thicknesses were characterized by SEM, XRD, and PL. The ZnO nanorods grown on the catalytic layer of 40 nm thickness show the best crystal and spatial orientation and as a result display the best optical properties. It was found that a catalytic ZnO thin-film of 40 nm in thickness yields well-aligned high-quality ZnO nanorods, due to its small surface roughness and structural strain.     

Enhanced luminescence of Ag-decorated ZnO nanorods

Ag-decorated ZnO nanorods were synthesized by thermal evaporation of a mixture of ZnO and graphite powders at 900 °C followed by wet Ag coating and thermal annealing. The ZnO nanorods had a rod-like morphology with a relatively uniform width and length. The widths and lengths of the nanorods ranged from 50 to 300 nm and up to a few hundred micrometers, respectively. The diameters of the Ag particles on the nanorods ranged from 10 to 100 nm. The dependence of the photoluminescence properties of Ag-decorated ZnO nanorods on the postannealing atmosphere was examined. Annealing resulted in an increase and decrease in the near band edge (NBE) and deep level (DL) emission intensities of Ag-coated ZnO nanorods, respectively, whereas both the NBE and DL emission intensities of uncoated ZnO nanorods were increased by annealing. The intensity ratio of NBE emission to DL emission of the Ag-coated ZnO nanorods was increased ~15-fold by hydrogen annealing. The underlying mechanism for NBE emission enhancement and DL emission suppression of Ag-coated ZnO nanorods by postannealing is discussed based on the surface plasmon resonance effect of Ag.     

Effect of leavening agent on structural and photocatalytic properties of ZnO nanorods

In the present work, we have demonstrated a simple, facile, one-step, rapid and cost effective synthesis of ZnO nanorods through the thermal decomposition of zinc acetate and leavening agent (NaHCO₃). The silver nanoparticles (AgNPs) were deposited on the surface of ZnO nanorods by photocatalytic reduction of Ag (I) to Ag(0). As synthesized ZnO nanorods and Ag–ZnO nanocomposites were characterized by using X-ray Diffraction, field emission scanning electron microscope, high-resolution transmission electron microscope and diffuse reflectance spectroscopy. The photocatalytic activities of the ZnO nanorods and Ag–ZnO nanocomposites were evaluated for the photodegradation of Methyl Orange (MO) under UV and sunlight irradiation. The use of common leavening agent helps to prevent the aggregation of ZnO nanorods, further it hinders crystallite growth and narrowing the diameter of nanorods by the evolution of carbon dioxide during calcination. The ZnO nanorods and Ag–ZnO nanocomposite exhibited an enhanced photocatalytic activity and separation of photogenerated electron and hole pairs. Due to effect of leavening agent and AgNPs deposited on surface of ZnO nanorods finds best catalyst for the 99% degradation of MO within 30 min compared to ZnO.     

ZnO单晶堆垒纳米棒的制备与表征

在Au点阵模板上磁控溅射ZnO薄膜,然后在O2气氛下1000℃退火制备了ZnO单晶堆垒纳米棒。采用扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)、X射线衍射(XRD)和傅立叶变换红外(FTIR)光谱对样品进行分析。结果表明,ZnO纳米棒是由诸多单晶堆垒而成,每个单晶均为六方纤锌矿结构,纳米棒直径在100nm左右。初步探讨了ZnO单晶堆垒纳米棒可能的生长机理。     

Epitaxial growth of ZnO layers using nanorods with high crystalline quality

Epitaxial ZnO films were grown on c-plane sapphire substrates by metal-organic chemical vapor deposition using a ZnO multi-dimensional structure having the sequence of ZnO film/ZnO nanorods/sapphire. The vertically well-aligned one-dimensional ZnO nanorods were grown epitaxially on the sapphire substrate with in-plane alignment under suitable growth conditions and then used as seeds for the subsequent epitaxial ZnO layer. For the transition of the ZnO structures from the nanorods to the film, the growth temperature and working pressure were controlled, while keeping the other conditions fixed. The growth of the ZnO films on the well-aligned ZnO nanorods results in homoepitaxial growth with the identical orientation relationship along the in-plane direction as well as the same c-axis orientation. The microstructural analysis of the multi-dimensional structure and analysis of the microstructural evolution from the one-dimensional nanorods to the two-dimensional film were conducted using transmission electron microscopy.     

Selective growth of ZnO nanorods on SiO2/Si substrates using a graphene buffer layer

A promising strategy for the selective growth of ZnO nanorods on SiO₂/Si substrates using a graphene buffer layer in a low temperature solution process is described. High densities of ZnO nanorods were grown over a large area and most ZnO nanorods were vertically well-aligned on graphene. Furthermore, selective growth of ZnO nanorods on graphene was realized by applying a simple mechanical treatment, since ZnO nanorods formed on graphene are mechanically stable on an atomic level. These results were confirmed by first principles calculations which showed that the ZnO-graphene binding has a low destabilization energy. In addition, it was found that ZnO nanorods grown on SiO₂/Si with a graphene buffer layer have better optical properties than ZnO nanorods grown on bare SiO₂/Si. The nanostructured ZnO-graphene materials have promising applications in future flexible electronic and optical devices.     

氧化锌纳米棒形貌对ZnO/Cu2O异质结太阳能电池光伏性能的影响

采用电化学沉积法制备了ZnO纳米棒,首先讨论了电化学沉积参数对氧化锌(ZnO)纳米棒形貌的影响,并对不同长度ZnO纳米棒的光吸收和反射等性质进行了研究.实验发现沉积时间是影响纳米棒长度、直径的重要因素,ZnO纳米棒的微观形貌对其光学性质有重要影响.然后以氧化锌纳米棒为n型材料,以氧化亚铜为p型材料,通过电化学沉积法构筑了ZnO/Cu2O异质结太阳能电池,并测试了其光伏性能,研究表明增长纳米棒阵列的长度使得开路电压、短路电流密度及光电转换效率等性能得到提升.最后,综合分析了氧化锌纳米棒形貌与所组装电池的性能之间的关系,发现调控氧化锌纳米棒的形貌是提高ZnO/Cu2O异质结太阳能电池光伏性能的有效途径.     

Optoelectronics behaviour of ZnO nanorods for UV detection

In this study ZnO nanorods have been synthesized by a chemical precipitation method. The room temperature UV–Vis absorption spectra of the ZnO nanorods indicated two absorption peaks in the UV region, one in the near UV region and the other attributed to the band gap of ZnO. The Photoluminescence spectra of ZnO nanorods show two emission bands, one ultraviolet emission band at 378 nm and the other in the defect related yellow emission band near 550 nm. The stimulated yellow luminescence of ZnO nanorods were affected by the synthesis time and annealing temperature. The same ZnO nanorods were deposited onto the ITO substrate to form a UV photoconductive detector. The ratio of the UV photogenerated current to dark current was as high as nine times under 3 V bias. Hence, these nanorods can be promising materials in the use of UV radiation detection.     

Growth of aligned ZnO nanorods on woven Kevlar® fiber and its performance in woven Kevlar® fiber/polyester composites

ZnO nanorods were grown by a seeding treatment on surface-functionalized woven Kevlar® fiber (WKF), and the decorated WKF was used to prepare composites with polyester resin (PES) via vacuum-assisted resin transfer molding. Fourier transform infrared spectroscopy (FT-IR) confirmed the surface functionalization of the WKF. The characteristic peaks of ZnO observed by FT-IR and X-ray diffraction (XRD) indicated the growth of ZnO nanorods on the surface of the WKF. FT-IR analyses of the composites were consistent with an interaction between the WKF, and ZnO and PES. The intensity of the XRD peak for crystalline ZnO increased with increasing growth of the nanorods. The morphology of the nanorods was studied by scanning electron microscopy. The growth of the nanorods increased with increasing treatment time. Thermogravimetric analysis also supported the growth of nanorods. The presence of ZnO nanorods significantly improved the impact resistance of the WKF/PES composites; the penetration thresholds were also determined. The WKF/ZnO/PES composites had substantially higher tensile strengths and moduli than the ZnO-free composites.     

Efficient dye-sensitized solar cells based on the combination of ZnO nanorods and microflowers

Well-aligned ZnO nanorod films were grown onto transparent conducting substrates by using an aqueous solution route. The presence of some reflections in the X-ray diffraction pattern of the ZnO films indicates the vertical alignment of the nanorods along the c axis of the wurtzite hexagonal structure. Well-aligned ZnO nanorods were observed by scanning electron microscopy. The presence of top ZnO microflower layers over the ZnO nanorod film was observed for all growth times studied. The ZnO nanorods with ZnO microflower top layers were applied as photoelectrodes in dye-sensitized solar cells. Higher photocurrent densities and photovoltages were observed with longer nanorod growth times. The high performance of the dye-sensitized solar cells might be associated to the combination of ZnO nanorods and microflowers in the same photoelectrode.     

微流控技术制备ZnO纳米棒及生物荧光检测性能研究

本研究设计并制备了一种微流控芯片并在其中水热合成了氧化锌(ZnO)纳米棒。利用扫描电子显微镜(SEM)和X射线衍射(XRD)研究了合成条件对ZnO纳米棒的形貌和晶体结构的影响。结果表明, 在微流控芯片中可制备得到致密的ZnO纳米棒, 其直径和长度随加热方式和制备时间的变化而改变。对比研究不同加热方式制备的ZnO纳米棒阵列检测异硫氰酸荧光素标记的羊抗牛IgG的性能, 发现局部加热方式制备的ZnO纳米棒检测荧光素标记蛋白的性能更佳, 在10 pg/mL~1 μg/mL范围内线性良好, 相关系数为0.99209。在此基础上, 用局部加热制备的ZnO纳米棒检测人甲胎蛋白(AFP), 其最低检测限可达1 pg/mL。这些结果表明, 微通道中合成的ZnO纳米棒适用于多通道荧光检测。     

Charge influence and growth mechanism of ZnO nanorods

We demonstrate the influence of charges near the substrate surface on vertically aligned ZnO nanorod growth. ZnO nanorods were fabricated on n-type GaN with and without H+ treatments by catalyst-free metal-organic chemical vapor deposition. The ZnO nanorods grown on n-GaN films were vertically well-aligned and had a well-ordered wurtzite structure. However, the ZnO did not form into nanorods and the crystal quality was very degraded as they were deposited on the H+ treated n-GaN films. The charge influence was also observed in the ZnO nanorod growth on sapphire substrates. These results implied that the charges near the substrate surface dominantly affected on the crystalization and formation of ZnO nanorods.