Large scale synthesis of bundles of aligned carbon nanotubes using a natural precursor: turpentine oil

Bundles of aligned carbon nanotubes (ACNTs) have been synthesised by spray pyrolysis of turpentine oil (inexpensive precursor) and ferrocene mixture at 800°C. Turpentine oil (C₁₀H₁₆), a plant-based precursor was used as a source of carbon and argon as a carrier gas. The bundles of ACNTs have been grown directly inside the quartz tube. The as-grown ACNTs have been characterised through X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopic techniques. Scanning electron microscope images reveal that the bundles of ACNTs are densely packed and are of ～70–130?µm in length. High-resolution transmission electron microscopy and Raman spectroscopy observations indicate that as-grown multi-walled carbon nanotubes (CNTs) are well graphitised. These CNTs have been found to have outer diameters between ～15 and 40?nm. This technique suggests a low-cost route for the large-scale formation of ACNTs bundles.     

用气相流动催化热解法合成单壁碳纳米管

以正硅酸乙酯(TEOS)为前驱体，二茂铁为催化剂前驱体，利用气相流动催化热解法在850～1160℃连续合成了单壁碳纳米管(SWNTs)．在此过程中，以由TEOS分解得到的二氧化硅颗粒和二茂铁分解得到的铁颗粒在气流中直接形成的复合粒于作为催化剂，二氧化硅作为铁颗粒的载体．电于显微镜和激光拉曼光谱的观测和分析表明，在所得到的产物中SWNTs的含量约为10％，其直径为1～2nm。     

用于制备优质单壁碳纳米管管束的MgO负载Fe3O4纳米粒子的合成

采用沉淀方法制备了直径分布狭窄的均匀Fe3O4纳米颗粒.Fe3O4纳粒形体几近一致,平均粒径为10.33 nm±2.99 nm(平均粒径±标准偏差).在超声作用下将MgO纳米颗粒分散在一定量Fe3O4纳米颗粒的水溶液中获得MgO负载Fe3O4的纳米颗粒.以甲烷为碳源,Fe3O4/MgO为催化剂,经化学气相沉积,在Fe3O4纳粒上制得了大量直径近乎均匀的单壁碳纳米管(SWCNTs)束.TEM显示:SWCNTs的平均直径1.22rm.热重分析显示:样品在400℃～600℃温度区间失重量约19％.拉曼光谱显示:SWCNTs的ID/IG的强度比为0.03,表明采用Fe3O4/MgO催化剂可制得高石墨化程度的单壁碳纳米管.     

Catalyst effect on the preparation of single-walled carbon nanotubes by a modified arc discharge

Single-walled carbon nanotubes (SWCNTs) were prepared by a modified arc discharge furnace using 500?Torr helium as buffer gas at 600?°C. The effect of the catalyst type on the production of SWCNTs was studied by transmission electron microscopy, X-ray diffraction and Raman spectroscopy. The experimental results indicated that the catalyst composition plays an important role in the production rate and purity of the SWCNTs product. Fe-Ni-Mg and Co-Ni powder catalysts demonstrated excellent catalytic effect at a catalyst content of 3?wt%. The soot production rate was up to 15?g/hr and the mean diameter of SWCNTs was about 1.3?nm.     

喷雾热解法在硅衬底上生长定向碳纳米管阵列(英文)

以向日葵油的甲基酯为碳源,二茂铁为催化剂前驱体,Ar为载气,通过喷雾热解法在硅衬底上合成定向碳纳米管阵列。结果表明,在硅衬底上原位形成Fe催化剂纳米颗粒。由拉曼光谱、透射电镜图和X-射线衍射谱图显示所制定向碳纳米管阵列具有较好的石墨化程度,其直径为1 0～3 0 nm,管壁约为1 0 nm。所制定向碳纳米管阵列中残留的催化剂含量可以忽略。     

Investigation of temperature effect on the mechanical properties of single-walled carbon nanotubes

A temperature-related higher-order gradient continuum theory is proposed for predicting the mechanical properties of single-walled carbon nanotubes (SWCNTs) at various temperatures. It is found that the axial elastic moduli of zigzag (21, 0), armchair (12, 12) and chiral (15, 9) SWCNTs with similar radii approach 0.7 TPa when T = 0 K, but decline slightly on different slopes. These results indicate that the temperature effect influences the axial Young moduli of zigzag SWCNTs less than those of the other types. Moreover, the parameters λ₁ and λ₂ corresponding to the uniform longitudinal and circumferential stretches at different temperatures are also examined, and the results show that with an increasing temperature, all SWCNTs are stretched in the longitudinal direction, while in the circumferential direction, only the zigzag SWCNTs are stretched, whereas the others are compressed.     

单壁碳纳米管的提纯方法

采用温控电弧炉，在600℃下，使用Fe／Ni/Mg催化剂大量制备了单壁碳纳米管。用两步纯化方法对单壁纳米管进行提纯：首先，原始的单壁碳纳米管在500℃，空气中加热30min；接着用37％的盐酸浸泡加热后的样品72h，水洗过滤后烘干,通过SEM、TGA、HRTEM和激光拉曼表征，纯化后单壁碳纳米管的纯度可高达95％，其直径范围为：1.24-1.38nm。     

Tunable separation of single-walled carbon nanotubes by dual-surfactant density gradient ultracentrifugation

We present a systematic study of the effects of surfactants in the separation of single-walled carbon nanotubes (SWNTs) by density gradient ultracentrifugation (DGU). Through analysis of the buoyant densities, layer positions, and optical absorbance spectra of SWNT separation using the bile salt sodium deoxycholate (DOC) and the anionic salt sodium dodecyl sulfate (SDS), we clarify the roles and interactions of these two surfactants in yielding different DGU outcomes. The separation mechanism described here can also help in designing new DGU experiments by qualitatively predicting outcomes of different starting recipes, improving the efficacy of DGU and simplifying post-DGU fractionation.      

Selective suspension in aqueous sodium dodecyl sulfate according to electronic structure type allows simple separation of metallic from semiconducting single-walled carbon nanotubes

Both density gradient centrifugation and gel electrophoresis have been reported to allow high throughput separation of metallic from semiconducting single-walled carbon nanotubes (SWNTs) when using aqueous sodium dodecyl sulphate (SDS) suspensions. We show here that both methods rely on an initial dispersion-by-sonication step, which is already selective with respect to electronic structure type. The corresponding aqueous SDS “starting” suspensions obtained after sonication and purification by simple centrifugation (70,000 g, 1 h) contain semiconducting SWNTs primarily in the form of small bundles whereas metallic SWNTs are predominantly suspended as individual tubes. Density gradient centrifugation then separates the bundles from the individual tubes on the basis of differences in their overall buoyant densities. Gel electrophoresis separates the longer bundles from the shorter individual tubes on the basis of their different mobilities. We also demonstrate that such starting suspensions can be fractionated according to electronic structure type by even simpler techniques such as size exclusion chromatography or gel filtration, thus opening the way for simple scale-up.      

Solvent-free derivatization of oxidized single-walled carbon nanotubes and nanodiamond with aminobenzo-crown ethers

We report on a one-step amide derivatization of two carbon nanomaterials (CNM) containing carboxylic functional groups, which are oxidized single-walled carbon nanotubes (SWNTs) and nanodiamond (ND), with amino-substituted crown ethers, namely, 4′-aminobenzo-15-crown-5 and 4′-aminobenzo-18-crown-6. The functionalization procedure proposed is based on thermal activation of COOH groups instead of traditional chemical activation, is fast and facile, does not require the use of organic solvents and can be considered as ecologically friendly. The nanohybrids of crown ethers with SWNTs and ND were characterized by means of Fourier-transform infrared and Raman spectroscopy, scanning and transmission electron microscopy, as well as thermogravimetric analysis and solubility tests in toluene and propanol. The approach proposed allows for a facile preparation of crown ether-functionalized SWNTs and ND without contamination with other chemical reagents, solvents and detergents, which might be especially important for a broad spectrum of applications ranging from nanoelectronics to nanomedicine.     

Moderate temperature synthesis of single-walled carbon nanotubes on alumina supported nickel oxide catalyst

A simple nickel oxide catalyst has been developed in synthesizing single-walled carbon nanotubes (SWNTs) at moderate temperature. The catalyst used in the experiment was without a preceding reduction in hydrogen flow. The synthesis of SWNTs was performed at a temperature of 700 °C, which represents a moderate reaction temperature. The presence of SWNTs on the catalyst was confirmed by transmission electron microscope (TEM) and Raman spectroscope. The Raman spectrum shows a strong intensity at the radial breathing mode, indicating that the occurrence of SWNTs was dominant. Raman data further reveals that the synthesized SWNTs had the diameters in the range from 0.58 to 2.02 nm.     

Selective adsorption of cations on single-walled carbon nanotubes: A density functional theory study

The selective adsorption of cation on single-walled carbon nanotubes (SWNTs) is systemically studied by using density functional theory calculations. It is found that the adsorption energy of cations on SWNTs depends on the concentration of cations and the diameter and the electronic structure of SWNTs. The binding strength of on each SWNT increases monotonically as the concentration of decreases, undergoing a change from endothermic to exothermic reaction. Generally speaking, the binding of on SWNTs becomes weaker as the diameter increases. In the medium-diameter region (9 < d < 11 Å), prefers to interact with metallic SWNTs (m-SWNTs) rather than semiconducting SWNTs (s-SWNTs) at the same concentration of . In the small-diameter region (d < 9 Å), the binding of is nearly independent of metallicity, but it is stronger than that of on the medium-diameter s-SWNTs. In the large-diameter region (d > 11 Å), the dependence of adsorption on the electronic structure is complicated, but the binding of is weaker than that on the medium-diameter s-SWNTs. Our results are in agreement with the experimental report that the small-diameter m- and s-SWNTs and the medium-diameter m-SWNTs are etched away by while the medium-diameter s-SWNTs and the large-diameter m- and s-SWNTs are intact.     

己烷低耗喷雾热解法大规模制备多壁碳纳米管

以己烷为碳源,二茂铁为催化剂前躯体,应用喷雾热解法,制备了多壁碳纳米管(MWCNTs).采用酸沥滤和空气氧化对MWCNTs进行纯化.利用SEM、TEM、XRD、EDS、TGA及Raman光谱分析等方法分别对原生和纯化MWCNTs进行表征.为制得优质、高产MWCNTs,对制备工艺参数作了优选,分别研讨了最佳制备参数,包括:二茂铁升华温度、己烷中二茂铁浓度、热解温度和时间,己烷与H2的流量比.MWCNTs具有典型的腊肠状(Sawsage-like)构型,长度大于数十微米,内、外管径分别为15nm～45nm及25nm～70nm,MWCNTs的纯度和产率的质量分数分别高于95%和70%.     

Hydrogen storage capacity of single-walled carbon nanotube prepared by a modified arc discharge

Single-walled carbon nanotubes (SWCNTs, the mean diameter of 1.35 nm) were produced by a modified arc discharging furnace using a mixture powder of KCl and Co-Ni alloy as catalyst at 600°C. The hydrogen storage capacity of SWCNTs was enhanced by the mechanism of atom hydrogen spillover from the supported catalyst. The temperature effect on the hydrogen storage capacity of as-grown SWCNTs was investigated. The relative experiments of SWCNT hydrogen uptake and release were carried out by a high-pressure volumetric gas-adsorption measurement system. The experimental results indicated that the hydrogen storage capacity of SWCNTs increased with the environmental temperatures decreasing. The hydrogen storage capacity of SWCNTs was up to 1.73 wt% at 77 K for 2 hours under the pressure of 10 MPa, and the corresponding releasing hydrogen capacity is about 1.23 wt% under ambient pressure.     

Wafer scale synthesis of dense aligned arrays of single-walled carbon nanotubes

Here we present an easy one-step approach to pattern uniform catalyst lines for the growth of dense, aligned parallel arrays of single-walled carbon nanotubes (SWNTs) on quartz wafers by using photolithography or polydimethylsiloxane (PDMS) stamp microcontact printing (μCP). By directly doping an FeCl₃/methanol solution into Shipley 1827 photoresist or polyvinylpyrrolidone (PVP), various catalyst lines can be well-patterned on a wafer scale. In addition, during the chemical vapor deposition (CVD) growth of SWNTs the polymer layers play a very important role in the formation of mono-dispersed nanoparticles. This universal and efficient method for the patterning growth of SWNTs arrays on a surface is compatible with the microelectronics industry, thus enabling of the fabrication highly integrated circuits of SWNTs.     

Flexible organic thin-film transistors using single-walled carbon nanotubes as an activated channel

We report on the fabrication of organic thin-film transistors (OTFTs) with a spun cross linked poly-4-vinylphenol (PVP) dielectric on a polyethersulphone (PES) flexible substrate. To improve the electrical performance of OTFTs, we employed a random single-walled carbon nanotubes (SWNTs) network as a carrier transfer underlay without sacrificing the flexibility of the TFTs. The random SWNTs showed that they can act as a semiconducting channel and conduction path to shorten the channel length in our TFTs. The flexible thin-film transistors (TFTs) with a random SWNTs/pentacene bilayer as an active channel exhibited an improved saturation field effect mobility (µ_sat) of 2.6 × 10^− 1 cm²/Vs compared to that of TFTs without the SWNTs underlay, while creating only a minor reduction of the current on/off ratio.     

单壁碳纳米管束的排布

流体排布法是实现碳纳米管定向排列的一种简单的方法。采用流体排布法在具有浸润性图案化的基底上成功地对单壁碳纳米管(SWNTs)束进行了水平方向上的排布。将SWNTs悬浮液滴入光刻胶制成的微通道中,在流体剪切力作用下,弯曲的SWNTs在一定程度上会被拉伸并且平行地排列在纳米级宽度的微通道中。将排列好的SWNTs阵列转移到一些不同间距的金电极对上面,制作成碳纳米管场效应晶体管(CNTFET)。CNTFET的电性能测试结果表明,制备的SWNTs束可以制造出不同电极间距同时具有良好电性能的CNTFET。     

Modal analysis of carbon nanotubes and nanocones using FEM

Modal analysis of single-walled carbon nanotubes (SWCNTs) and nanocones (SWCNCs) was performed using a finite element method (FEM) with ANSYS. The vibrational behaviors of fixed beam and cantilever SWCNTs with different section types of a circle and an ellipse were modeled using three-dimensional elastic beams of carbon bonds and point masses. Also, the vibrational behaviors of fixed beam and cantilever SWCNCs with different disclination angles of 120°, 180°, and 240° were modeled using the same method. The beam element natural frequencies were calculated by considering the mechanical characteristics of the covalent bonds between the carbon atoms in the hexagonal lattice. Each mass element of the carbon atoms was assigned as a point mass at the nodes of the FEM elements. The natural frequencies of zigzag and armchair SWCNTs and SWCNCs were also computed. There were some differences between the findings obtained in this study and the molecular structural mechanics data available in the literature. The natural frequencies of SWCNCs were estimated depending on the geometrical type and disclination angle with different boundary conditions. The natural frequencies of the SWCNCs with disclination angles of 120°, 180°, and 240° increased significantly at higher modes of vibration.     

Magnetophoretic continuous purification of single-walled carbon nanotubes from catalytic impurities in a microfluidic device

A magnetophoretic continuous purification method is presented of single-walled carbon nanotubes (SWCNTs) from the superparamagnetic iron-catalyst impurities in a microfluidic device without any influence on inherent SWCNT properties. By employing microfluidics and a magnetic-field-induced saw-tooth nickel microstructure, a highly enhanced magnetic force in adjoining microchannels is exploited. The iron impurities of SWCNTs are attracted towards areas of higher magnetic-flux density in the microchannels where magnetic field was asymmetrically generated perpendicularly to the streamline. We obtained highly purified SWCNTs at a rate of 0.36 mg h(-1) and that are estimated to be about 99% purity.