Microwave dielectric properties of Ba2 − xSrxLa3Ti3NbO15 ceramics

High dielectric constant and low loss ceramics in the system Ba_2 − xSr_xLa₃Ti₃NbO₁₅ (x = 0-1) have been prepared by conventional solid-state ceramic route. Ba_2 − xSr_xLa₃Ti₃NbO₁₅ solid solutions adopted A₅B₄O₁₅ cation-deficient hexagonal perovskite structure for all compositions. The materials were characterized at microwave frequencies. They show a linear variation of dielectric properties with the value of x. Their dielectric constant varies from 48.34 to 43.03, quality factor Q_u × f from 20,291 to 39,088 GHz and temperature variation of resonant frequency from 8 to 1.39 ppm/°C as the value of x increases. These low loss ceramics might be used for dielectric resonator (DR) applications.     

Fabrication of (K, Na)NbO3 glass-ceramics and crystal line patterning on glass surface

Crystallization behavior of (30−x)K₂O-xNa₂O-25Nb₂O₅-45SiO₂ (KNNS; x = 0, 5, 10, 20 and 30) (mol%) glasses was clarified and perovskite-type nonlinear optical (K, Na)NbO₃ (KNN) crystals were synthesized by using a conventional glass-ceramics method. It was found that Na₂O amounts over around x = 10 mol% were necessary to form perovskite-type KNN crystals showing second-harmonic generations. The substitution of K⁺ and Na⁺ ions was confirmed from X-ray diffraction (XRD) analysis. A continues-wave of Yb:YVO₄ fiber laser (wavelength: 1080 nm) was irradiated onto CuO doped KNNS; x = 10 (Cu-KNNS) surface. The absorption coefficient of this Cu-KNNS glass was determined to be α = 5.0 cm⁻¹. Perovskite-type KNN crystals were patterned in the condition of the laser power of >1.20 W and the laser scanning speed of S = 7 μm/s, and their structure was determined by Raman scattering spectra and XRD analysis.     

Characterization of (K0.5Na0.5)NbO3 powders and ceramics prepared by a novel hybrid method of sol–gel and ultrasonic atomization

(K_0.5Na_0.5)NbO₃ powders and ceramics were prepared by a novel hybrid method of sol–gel and ultrasonic atomization, in which Nb₂O₅ was used as the niobium source to replace those expensive soluble niobium salts. X-ray diffraction and thermal analysis were performed to investigate the synthesis process and phase transformation behavior of (K_0.5Na_0.5)NbO₃ powders. The results showed that (K_0.5Na_0.5)NbO₃ powders with a reasonably fine particle size and single-phase perovskite structure were formed at a temperature as low as 650 °C. Dense (K_0.5Na_0.5)NbO₃ ceramics with a relative density of 93% were obtained using the refined powders. The (K_0.5Na_0.5)NbO₃ ceramics prepared by the novel hybrid method exhibited relatively good properties (d₃₃ = 90 pC/N, k_p = 0.32, P_r = 20.6 μC/cm², T_c = 405 °C, ε_r = 712), suggesting that this novel hybrid method might be a promising method for the powders and ceramics preparation.     

Influence of sintering temperature on piezoelectric properties of (K0.5Na0.5)NbO3-LiNbO3 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ have been synthesized by traditional ceramics process without cold-isostatic pressing. The effect of the content of LiNbO₃ and the sintering temperature on the phase structure, the microstructure and piezoelectric properties of (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ ceramics were investigated. The result shows that the phase structure transforms from the orthorhombic phase to tetragonal phase with the increase of the content of LiNbO₃, and the orthorhombic and tetragonal phase co-exist in (K_0.5Na_0.5)NbO₃-LiNbO₃ ceramics when the content of LiNbO₃ is about 0.06 mol. The sintering temperature of (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ decreases with the increase of the content of LiNbO₃. The optimum composition for (1 − x)(K_0.5Na_0.5)NbO₃-xLiNbO₃ ceramics is 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃. The optimum sintering temperature of 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃ ceramics is 1080 °C. Piezoelectric properties of 0.94 (K_0.5Na_0.5)NbO₃-0.06LiNbO₃ ceramics under the optimum sintering temperature are piezoelectric constant d₃₃ of 215 pC/N, planar electromechanical coupling factor k_p of 0.41, thickness electromechanical coupling factor k_t of 0.48, the mechanical quality factor Q_m of 80, the dielectric constant of 530 and the Curie temperature T_c = 450 °C, respectively. The results indicate that 0.94(K_0.5Na_0.5)NbO₃-0.06LiNbO₃ piezoelectric ceramics is a promising candidate for lead-free piezoelectric ceramics.     

Morphotropic phase boundary and piezoelectric properties of (Bi1/2Na1/2)1 − x(Bi1/2K1/2)xTiO3-0.03(Na0.5K0.5)NbO3 ferroelectric ceramics

Lead-free piezoelectric ceramics, (Bi_1/2Na_1/2)_1 − x(Bi_1/2K_1/2)_xTiO₃-0.03(Na_0.5K_0.5)NbO₃ (x = 0.10-0.40) were synthesized by conventional solid-state sintering. A morphotropic phase boundary (MPB) between rhombohedral and tetragonal phases was confirmed. Two dielectric anomalies can be observed, showing diffused phase transition behavior. There is no shift of the dielectric maximum temperature with frequency due to the contribution of space charge at high temperatures, similar to pure (Bi_1/2Na_1/2)TiO₃. The materials near MPB show a strong compositional dependence with the optimal properties of a d₃₃ of 167 pC/N, a k_p of 35.5%, a P_r of 27.6 μC/cm² and a E_c of 27.9 kV/cm, suitable for future application.     

One-step synthesis and double emission (Ca1 + x − yEuy)Ga2S4 + x phosphor for white LEDs

(Ca_{1 + x − y}Eu_y)Ga₂S_4 + x phosphors have been synthesized one step by solid state reaction. The photoluminescence excitation and emission spectra of phosphors have been studied; the influence of host composition and Eu²⁺ concentration on emission spectra has also been investigated. The emission spectrum consists of yellow emission at 550 nm and red emission at 650 nm. It also indicates that the excitation spectrum is a broadband and can be well matched with the emission of GaN chip. Combined these phosphors with 460 nm-emitting GaN chips, White LEDs have been fabricated. Their electroluminescence spectra have been measured under 20 mA forward-bias current. Their CIE chromaticity coordinates and color temperature indicate that (Ca_{1 + x − y}Eu_y)Ga₂S_4 + x phosphors are promising phosphors for GaN-based white LEDs.     

Influence of SnO2 addition on the thermoelectric properties of Zn1 − xSnxO (0.01 ≤ x ≤ 0.05)

The grain size and the density of the Zn_1 − xSn_xO (0 ≤ x ≤ 0.05) samples decreased with increasing SnO₂ content. The addition of a small amount of SnO₂ (x ≤ 0.01) to ZnO led to an increase in both the electrical conductivity and the absolute value of the Seebeck coefficient, resulting in a significant increase in the power factor. The thermoelectric power factor was maximized to a value of 1.25 × 10⁻³ Wm⁻¹ K⁻² at 1073 K for the Zn_0.99Sn_0.01O sample.     

Eu-Mössbauer spectroscopic and X-ray diffraction study on EuyM1−yO2−x (0 ≤ y ≤ 1.0) (M = Th, U)

¹⁵¹Eu-Mössbauer spectroscopic and powder X-ray diffraction (XRD) study has been performed for the Eu_yM_1−yO_2−x (M = Th and U) systems over the entire composition range of 0 ≤ y ≤ 1.0. The XRD results of the Eu-Th system showed that a very wide defect-fluorite (DF) type phase in which oxygen vacancies (V_O) are disordered (x = y/2) is formed for 0 ≤ y < 0.5 and that two-phase regions sandwitching a narrow C-type (C) single phase around y ≈ 0.8 appear for 0.5 < y < 0.8 (DF + C) and 0.82 < y < 1.0 (C + B-type (monoclinic) Eu₂O₃). The Mössbauer results show that the isomer shifts (ISs) of Eu³⁺ in this system smoothly increase with Eu composition, y. The decrease of average coordination number (CN) of O²⁻ around Eu³⁺ with increasing y (CN = 8 − 2y) (x = y/2) results in the decrease of the average EuO bond length, which is due to the decrease of repulsion force between O²⁻ anions. This result confirms that the IS of Eu³⁺ correlates well with the average EuO bond length in oxide systems. For the Eu-U system, the lattice parameter, a₀, of the system decreases almost linearly with y, in accordance with the calculated a₀ versus y curve for the oxygen-stoichiometric (i.e. x = 0) fluorite-type dioxide (CN = 8). The ISs of Eu³⁺ in this composition range remain almost constant around 0.5 mm/s, which is comparable to those of pyrochlore oxides (Eu₂Zr₂O₇ and Eu₂Hf₂O₇ (y = 0.5)) with O²⁻-eight-fold coordinated Eu³⁺(CN = 8).     

Oxygen vacancy ordering in strontium doped rare earth cobaltate perovskites Ln1−xSrxCoO3−δ (Ln = La, Pr and Nd; x > 0.60)

A family of Sr-doped perovskite compounds Ln_1−xSr_xCoO_3−δ (Ln = La³⁺, Pr³⁺ and Nd³⁺; x > 0.60), were prepared by sol-gel chemistry and reaction at 1100 °C under 1 atm of oxygen. This structural family has been shown to be present only for rare earth ions larger than Sm³⁺ and an upper limit of Sr²⁺ solubility in these phases was found to exist between x = 0.90 and 0.95. X-ray diffraction shows oxygen-deficient, simple cubic (Pm-3m) perovskite crystal structures. The combination of electron and powder neutron diffraction reveals that oxygen vacancy ordering occurs, leading to a tetragonal (P4/mmm) superstructure and a doubling of the basic perovskite unit along the crystallographic c-axis. No additional Ln³⁺/Sr²⁺ cation ordering was observed.     

Preparation of Ti1− zNbzN ceramics by spark plasma sintering Ti1− zNbzOxNy nanopowders

Ti_1−zNb_zN ceramics were fabricated by sintering nanocrystalline titanium-niobium oxynitride (Ti_1−zNb_zO_xN_y) powders using spark plasma sintering (SPS) technique at 1060 °C for 3 min in an N₂ atmosphere. The phase composition and microstructure were characterized by XRD, SEM, TEM and EDS. The results showed that Ti_1−zNb_zN ceramics remained the cubic structures of Ti_1−zNb_zO_xN_y powders. There were XRD peak shifts in the cubic phases between Ti_1−zNb_zN ceramics and corresponding Ti_1−zNb_zO_xN_y powders. During the sintering process, oxygen separated from Ti_1−zNb_zO_xN_y to form titanium-niobium oxides. Ti_1−zNb_zN (0 < z < 1) had a more compact structure than TiO_xN_y and NbO_xN_y. Ti_0.5Nb_0.5N ceramic had the biggest grain size in the series of Ti_1−zNb_zN.     

Enhanced dielectric,ferroelectric and optical properties of lead free (K0.17Na0.83)NbO3 ceramic with WO3 addition

Polycrystalline lead-free ceramics (K_0.17Na_0.83)NbO₃ + x wt.% WO₃; (x = 0, 1, 3 and 5) have been synthesized via solid state reaction method. X-ray diffraction pattern at room temperature indicates the formation of pure perovskite phase with monoclinic structure for all samples. Dielectric constant versus temperature measurements shows an increase in dielectric constant with a shift in Curie temperature (T_C) toward higher temperature side. Remnant polarization (P_r) is found to be enhanced and reached upto 24 μC/cm² for x = 5 wt.% WO₃ from 12.5 μC/cm² for pure (K_0.17Na_0.83)NbO₃ ceramic. The value of coercive field (E_c) decreases with increasing wt.% of WO₃. From optical band gap study, we found blue shift in the band gap of (K_0.17Na_0.83)NbO₃ with increasing concentration of WO₃.     

Synthesis of three dimensional photoluminescent [In10S20 − xSex] supertetrahedral clusters: (x < 0.3)

Two strong solid state luminescence peaks, centered at 457 nm and 538 nm, were observed from the newly synthesized ternary [In₁₀S_20 − xSe_x]¹⁰⁻ T3 clusters, under excitation by UV radiation (λ = 360 nm). The 457 nm peak is due to the porosity property of T3 clusters. Nevertheless, the 538 nm peak has not been reported for the T3 clusters before. In this letter, we demonstrate that the 538 nm peak is attributed to the trace Se atoms confined in the [In₁₀S_20 − xSe_x]¹⁰⁻ clusters. The luminescent output from the ternary [In₁₀S_20 − xSe_x]¹⁰⁻ T3 clusters is independent of temperature from 298 K until 77 K.     

Oxide-ion conductivity in CuxCe1−xO2−δ (0 ≤ x ≤ 0.10)

Up to 10 at.% of copper readily substitutes for cerium in ceria. It is found that at oxygen partial pressures between 0.21 atm and 10⁻⁵ atm, Cu_xCe_1−xO_2−δ (0 ≤ x ≤ 0.10) solid solution behave as an oxide-ion electrolyte. Interestingly, Cu_0.10Ce_0.90O_2−δ exhibits the oxide-ion conductivity of ca. 10⁻⁴ Ω⁻¹ cm⁻¹ at 600 °C at an oxygen partial pressure of 10⁻⁵ atm.     

Study on the optical properties of Zn1−xMgxS (0 ≤ x ≤ 0.55) quantum dots prepared by precipitation method

Zn_1−xMg_xS (0 ≤ x ≤ 0.55) quantum dots (QDs) were successfully synthesized by precipitation method. The crystal structures, microstructures, and optical properties of the Zn_1−xMg_xS QDs were investigated using X-ray diffraction, scanning electron microscopy, and ultraviolet-visible and photoluminescence (PL) spectroscopy. The Zn_1−xMg_xS QDs were found to have a cubic crystal structure and an average crystallite size of 6.40-7.96 nm. It has been shown that an increase in doping Mg²⁺ concentration in Zn_1−xMg_xS QDs led to a gradual widening of the band gap and a weakening in the PL intensity of the Zn_1−xMg_xS QDs.     

Study of flash evaporated CuIn1 − xGaxTe2 (x = 0, 0.5 and 1) thin films

CuIn_1 − xGa_xTe₂ thin films with x = 0, 0.5 and 1, have been prepared by flash evaporation technique. These semiconducting layers present a chalcopyrite structure. The optical measurements have been carried out in the wavelength range 200-3000 nm. The linear dependence of the lattice parameters as a function of Ga content obeying Vegard's law was observed. The films have high absorption coefficients (4 · 10⁴ cm^− 1) and optical band gaps ranging from 1.06 eV for CuInTe₂ to 1.21 eV for CuGaTe₂. The fundamental transition energies of the CuIn_1 − xGa_xTe₂ thin films can be fitted by a parabolic equation namely E_g1(x) = 1.06 + 0.237x − 0.082x². The second transition energies of the CuInTe₂ and CuGaTe₂ films were estimated to be: E_g2 = 1.21 eV and E_g2 = 1.39 eV respectively. This variation of the energy gap with x has allowed the achievement of absorber layers with large gaps.     

Synthesis and electrochemical properties of Ti doped Li3 − xFe2 − xTix(PO4)3/C cathode materials

Li_3 − xFe_2 − xTi_x(PO₄)₃/C (x = 0-0.4) cathodes designed with Fe doped by Ti was studied. Both Li₃Fe₂(PO₄)₃/C (x = 0) and Li_2.8Fe_1.8Ti_0.2(PO₄)₃/C (x = 0.2) possess two plateau potentials of Fe³⁺/Fe²⁺ couple (around 2.8 V and 2.7 V vs. Li⁺/Li) upon discharge observed from galvanostatic charge/discharge and cyclic voltammetry. Li_2.8Fe_1.8Ti_0.2(PO₄)₃/C has higher reversibility and better capacity retention than that of the undoped Li₃Fe₂(PO₄)₃/C. A much higher specific capacity of 122.3 mAh/g was obtained at C/20 in the first cycle, approaching the theoretical capacity of 128 mAh/g, and a capacity of 100.1 mAh/g was held at C/2 after the 20th cycle.     

Synthesis of perovskite-type (La1−xCax)FeO3 (0 ≤ x ≤ 0.2) at low temperature

Gel formation was realized by adding citric acid to a solution of La(NO₃)₃·5H₂O, Ca(NO₃)₂·4H₂O, and Fe(NO₃)₂·9H₂O. Perovskite-type (La_1−xCa_x)FeO₃ (0 ≤ x ≤ 0.2) was synthesized by firing the gel at 500 °C in air for 1 h. The crystallite size (D_1 2 1) decreased with increasing x, while the specific surface area was 6.8-9.4 m²/g and independent of x. The XPS measurement of the (La_1−xCa_x)FeO₃ surface indicated that the Ca²⁺ ion content increased with increasing x, while the Fe ion content was independent of x. Catalytic activity for CO oxidation increased with increasing x.     

Magnetocaloric properties in Ln0.67Ba0.33Mn1 − xFexO3 (Ln = La or Pr) manganites

We have investigated the magnetocaloric properties of Ln_0.67Ba_0.33Mn_1 − xFe_xO₃ (Ln = La or Pr) manganites with x = 0 and 0.05. All compounds present a maximum and large magnetocaloric effect near the Curie temperature (T_C). The associated maximum value of the magnetic entropy change, at 5 T applied change in the magnetic field, is 4.37 J.kg^− 1.K^− 1 for Pr_0.67Ba_0.33MnO₃ manganite with a T_C value of 205 K. The corresponding relative cooling power (RCP) reaches 230 J.kg^− 1. All the samples present similar RCP values that are relatively high and are promising materials to be used in ecologically friendly magnetic refrigeration technology. Iron doping reduces both T_C and ΔS_M^max and spreads the temperature working range with an almost constant RCP and can then be used to tune the working conditions of a refrigerator device.     

Order-disorder phase transitions and high-temperature oxide ion conductivity of Er2+xTi2−xO7−δ (x = 0, 0.096)

The Er_2+xTi_2−xO_7−δ (x = 0.096; 35.5 mol% Er₂O₃) solid solution and the stoichiometric pyrochlore-structured compound Er₂Ti₂O₇ (x = 0; 33.3 mol% Er₂O₃) are characterized by X-ray diffraction (phase analysis and Rietveld method), thermal analysis and optical spectroscopy. Both oxides were synthesized by thermal sintering of co-precipitated powders. The synthesis study was performed in the temperature range 650-1690 °C. The amorphous phase exists below 700 °C. The crystallization of the ordered pyrochlore phase (P) in the range 800-1000 °C is accompanied by oxygen release. The ordered pyrochlore phase (P) exists in the range 1000−1200 °C. Heat-treatment at T ≥ 1600 °C leads to the formation of an oxide ion-conducting phase with a distorted pyrochlore structure (P2) and an ionic conductivity of about 10⁻³ S/cm at 740 °C. Complex impedance spectra are used to separately assess the bulk and grain-boundary conductivity of the samples. At 700 °C and oxygen pressures above 10⁻¹⁰ Pa, the Er_2+xTi_2−xO_7−δ (x = 0, 0.096) samples are purely ionic conductors.     

Synthesis of (1 − x)Ca2/5Sm2/5TiO3-xLi1/2Nd1/2TiO3 ceramic powder via ethylenediaminetetraacetic acid precursor

(1 − x)Ca_2/5Sm_2/5TiO₃-xLi_1/2Nd_1/2TiO₃ (CSLNT) ceramic powder was prepared by a liquid mixing method using ethylenediaminetetraacetic acid (EDTA) as the chelating agent. TG, DTA, XRD and TEM characterized the precursors and derived oxide powders. When x = 0.3, perovskite CSLNT was synthesized at 1000 °C for 3 h in air. The CSLNT (x = 0.3) ceramics sintered at 1200 °C for 3 h show excellent microwave dielectric properties of ?_r = 99, Q_f = 6200 GHz and τ_f = 9 × 10⁻⁶ °C⁻¹.