β-Galactosidase-based colorimetric paper sensor for determination of heavy metals

We demonstrate a novel approach for rapid, selective, and sensitive detection of heavy metals using a solid-phase bioactive lab-on-paper sensor that is inkjet printed with sol-gel entrapped reagents to allow colorimetric visualization of the enzymatic activity of β-galactosidase (B-GAL). The bioactive paper assay is able to detect a range of heavy metals, either alone or as mixtures, in as little as 10 min, with detection limits as follows: Hg(II) = 0.001 ppm; Ag(I) = 0.002 ppm, Cu(II) = 0.020 ppm; Cd(II) = 0.020 ppm; Pb(II) = 0.140 ppm; Cr(VI) = 0.150 ppm; Ni(II) = 0.230 ppm. The paper-based assay was immune to interferences from nontoxic metal ions such as Na(+) or K(+), could be used to detect heavy metals that were spiked into tap water or lake water, and provided quantitative data that was in agreement with values obtained by atomic absorption. With the incorporation of standard chromogenic metal sensing reagents into a multiplexed bioactive paper sensor, it was possible to identify specific metals in mixtures, albeit with much lower detection limits than were obtained with the enzymatic assay. The paper-based sensor should be valuable for rapid, on-site screening of trace levels of heavy metals in resource limited areas and developing countries.     

Utilization of ICP/OES for the determination of trace metal binding to different humic fractions

In this study, the use of inductively coupled plasma/optical emission spectrometry (ICP/OES) to determine multi-metal binding to three biomasses, Sphagnum peat moss, humin and humic acids is reported. All the investigations were performed under part per billion (ppb) concentrations. Batch pH profile experiments were performed using multi-metal solutions of Cd(II), Cu(II), Pb(II), Ni(II), Cr(III) and Cr(VI). The results showed that at pH 2 and 3, the metal affinity of the three biomasses exposed to the multi-metal solution that included Cr(III) presented the following order: Cu(II), Pb(II)>Ni(II)>Cr(III)>Cd(II). On the other hand, when Cr(VI) was in the heavy metal mixture, Sphagnum peat moss and humin showed the following affinity: Cu(II), Pb(II)>Ni(II)>Cr(VI)>Cd(II); however, the affinity of the humic acids was: Cu(II)>Pb(II), Cr(VI)>Ni(II)>Cd(II). The results demonstrated that pH values of 4 and 5 were the most favorable for the heavy metal binding process. At pH 5, all the metals, except for Cr(VI), were bound between 90 and 100% to the three biomasses. However, the binding capacity of humic acids decreased at pH 6 in the presence of Cr(VI). The results showed that the ICP/OES permits the determination of heavy metal binding to organic matter at ppb concentration. These results will be very useful in understanding the role of humic substances in the fate and transport of heavy metals, and thus could provide information to develop new methodologies for the removal of low concentrations of toxic heavy metals from contaminated waters.     

Determination of heavy metals by ICP-OES and F-AAS after preconcentration with 2,2'-bipyridyl and erythrosine

The applicability of 2,2'-bipyridyl and erythrosine co-precipitation method for the separation and preconcentration of some heavy metals, such as Cd, Co, Cu, Ni, Pb and Zn in actual samples for their determination by ICP-OES and F-AAS was studied. Experimental conditions influencing the recovery of the investigated metals, such as pH, molar ratio of 2,2'-bipyridyl to erythrosine, the effect of time on co-precipitation were optimized. The analytical characteristics of the method (e.g. limit of detection, sensitivity, linear range and preconcentration factor) were obtained. The limits of detection LOD (ng mL(-1)) of the ICP-OES (F-AAS) method were: Cd: 4.0 (7.75), Co: 3.1 (57.2), Cu: 18 (10.3), Ni 21.3 (32.8), Pb: 35.9 (29.2) and Zn: 10.2 (6.90). The recovery of all the elements tested was more than 93%. The influence of inorganic matrix was examined. The proposed method was applied to determination of Cd, Co, Cu, Ni, Pb and Zn in vegetables and certified reference material (NCS ZC85006 Tomato).     

Complexing of heavy metals with DNA and new bioaffinity method of their determination based on amperometric DNA-based biosensor

The immobilized single-stranded DNA (ssIDNA) has been found to be a very effective biospecific analytical reagent when used in a newly developed bioaffinity method of the determination of heavy metals based on the amperometric DNA-based biosensor. This has been concluded from the comparative study of the complexing of heavy metals with double-stranded DNA, single-stranded DNA, and ssIDNA, using Fe(III) and Cu(II) as a model (metal/nucleotide ratio and stability constants are maximum for ssIDNA), from the study of adsorption of Fe(III), Cu(II), Pb(II), and Cd(II) on nitrocellulose membranes, containing single-stranded DNA, and from the determination of their binding constants with ssIDNA. According to these data, the chosen heavy metals can be lined up in a series of binding strengths with ssIDNA: Cu(II) > Pb(II) > Fe(III) > Cd(II). The method of the determination of heavy metals is based on biospecific preconcentration of metal ions on the biosensor followed by the destruction of DNA-metal complexes with ethylenediaminetetraacetate and voltammogram recording has been proposed. The lower detection limits are 4.0 x 10(-11), 1.0 x 10(-10), 1.0 x 10(-9), and 5.0 x 10(-9) M for Cu(II), Pb(II), Cd(II), and Fe(III), respectively. The heavy metals have been assayed in multicomponent environmental and biological systems such as natural and drinking water, milk, and blood serum samples.     

Antimony film electrode for electrochemical stripping analysis

In this work, an antimony film electrode (SbFE) is reported for the first time as a possible alternative for electrochemical stripping analysis of trace heavy metals. The SbFE was prepared in situ on a glassy carbon substrate electrode and employed in combination with either anodic stripping voltammetry or stripping chronopotentiometry in nondeaerated solutions of 0.01 M hydrochloric acid (pH 2). Several key operational parameters influencing the electroanalytical response of SbFE were examined and optimized, such as deposition potential, deposition time, and composition of the measurement solution. The SbFE exhibited well-defined and separated stripping signals for both model metal ions, Cd(II) and Pb(II), surrounded with low background contribution and a relatively large negative potential range. The electrode revealed good linear behavior in the examined concentration range from 20 to 140 microg L-1 for both test metal ions, with a limit of detection (3sigma) of 0.7 microg L-1 for Cd(II) and 0.9 microg L-1 for Pb(II) obtained after a 120 s deposition step, and good reproducibility, with a relative standard deviation (RSD) of +/-3.6% for Cd(II) and +/-6.2% for Pb(II) (60 microg L-1, n = 12). When comparing the SbFE with the commonly used mercury film electrode and recently introduced bismuth film electrode, the newly proposed electrode offers a remarkable performance in more acidic solutions (pH < or = 2), which can be advantageous in electrochemical analysis of trace heavy metals, hence contributing to the wider applicability of electrochemical stripping techniques in connection with "mercury-free" electrodes.     

Modification of rice hull and sawdust sorptive characteristics for remove heavy metals from synthetic solutions and wastewater

In this work two modified agricultural residues, rice hull and sawdust were examined as sorbents to remove heavy metals Pb(II), Cd(II), Zn(II), Cu(II) and Ni(II) from synthetic solutions or wastewater samples. To modify their sorptive characteristics, samples were treated with HCl, NaOH and heat. The sorption of the heavy metals from the synthetic solutions was increased with pH and initial concentration. In pH 5, Pb(II) and Cd(II) showed the highest sorption and Cu(II), Zn(II) and Ni(II) showed the following orders, respectively. Sorption capacity of rice hull was higher than sawdust. The modifications changed the sorption capacity of the natural sorbents in the following order base>heat>natural>acid. The sorption isotherms of sorbents were best described by the Freundlich and Langmuir models. The basic treated rice hull and sawdust followed by the heat treated rice hull sorbed the maximum of heavy metals from the industrial wastewater samples. In the column experiment, the synthetic solutions and the wastewater samples gave almost the same results as the suspensions. The recovery of the columns using water and HCl showed positive results. Commercial sorbents removed Pb(II), Zn(II) and Ni(II) a little more than rice hull.     

Estimation of selected heavy metals and arsenic in PM10 aerosols in the ambient air of the Greater Athens Area, Greece

Aerosol samples of PM(10) were collected during summer and winter 2003 at two different sites in the Messogia Basin northeast of Athens, to demonstrate the variations of heavy metals in PM(10) and examine their relationship with both gaseous pollutants and meteorological parameters. Estimated heavy metals during the experimental campaign were mercury (Hg), cadmium (Cd), lead (Pb), nickel (Ni) and arsenic (As). The average heavy metal concentrations for the first site (Spata) constituted 0.66-14.7ng/m(3) for the summer period and 0.14-19.5ng/m(3) for the winter period. At the second site (Koropi), the corresponding values varied between 0.89 and 13.3ng/m(3) and 0.16 and 24.7ng/m(3), respectively. PM(10) Hg, PM(10) Cd and PM(10) Ni contents showed regular daily variations, with higher mass percentages during the summer, indicating differences in local PM(10) sources for each season. On the contrary, PM(10) Pb presented higher mass percentages during the winter. Examination of the relationship between heavy metals and meteorological parameters indicated a higher correlation with temperature and relative humidity, especially for Pb. In addition, most of the heavy metals (apart from Hg) presented an expected correlation with nitrate oxides (NO(x)), PM(10) and ozone (O(3)). Higher correlations with both meteorological parameters and gaseous pollutants were observed during the winter experimental campaign. Maximum heavy metal concentrations at both sites were observed during days with NE or NNE prevailing winds during the summer campaign, while the winter period was characterized with maximums during days with W or WNW prevailing winds.     

The bonding of heavy metals on nitric acid-etched coal fly ashes functionalized with 2-mercaptoethanol or thioglycolic acid

Coal fly ash is a waste by-product of the coal fire industry, which generates many environmental problems. Alternative uses of this material would provide efficient solutions for this by-product. In this work, nitric acid-etched coal fly ash labelled with 2-mercaptoethanol or thioglycolic acid was assessed for retention of Al(III), As(III), Cu(II), Cd(II), Fe(III), Mn(II), Hg(II), Ni(II), Pb(II) and Zn(II) ions. The bonding characteristics between the organic compounds with the solid support, as well as with the metal ions, were evaluated using various surface analytical techniques. Visualization of the organically-functionalized coal fly ash particle was possible using scanning electron microscopy (SEM), while the elemental composition of the functionalized material, before and after retention of the metal ions, was obtained by energy dispersive (ED)-X ray spectrometry (XRS) and electrothermal atomic absorption spectrometry (ETAAS). Fourier transform infrared (FT-IR) spectrometry and Raman spectrometry were used to obtain information about the functional groups. It was found that some metal(oid) ions (As, Ni, Pb, Zn) were coordinated through the mercaptan group, while other metal(oid)s (Al, Cd, Cu, Fe, Hg, Mn) were apparently bonded to oxygen atoms. A low-cost and effective solid phase retention system for extraction of heavy metals from aqueous solutions was thus developed.     

Synthesis of polyimide from 5,5'-bis(bromomethyl)-2,2':6',2'-terpyridine and investigation of the polymer sorption behavior towards some metal ions

The synthesis of a terpyridine-based polyimide sorbent for solid-phase extraction (SPE) of some metal ions is described. For this purpose, 5,5'-bis(bromomethyl)-2,2':6',2'-terpyridine was polymerized with the corresponding diimide derivatives of dianhyrides to give polyimides utilizing terpyridine unit in the main chain. This polymer was used for its extraction capabilities for Pb(II), Ni(II), Cu(II), Zn(II), Cd(II) and Hg(II), at different pH. Under competitive conditions and at pH<0.6, the selectivity order was Pb approximately Cd approximately Zn. Enhanced selectivity was observed at pH 3.5, the order was Cu>Ni>Zn approximately Cd approximately Pb. Quantitative recoveries>97% were observed for all metals in case loading was stopped before reaching the point of breakthrough. As the synthesized polyimides are insoluble in water, solid-liquid extractions have been carried out and the resins sorption for mixture of basic and/or precious metals have been studied under various experimental conditions (reaction time and hydrochloric acid concentration).     

Procion Green H-4G immobilized poly(hydroxyethylmethacrylate/chitosan) composite membranes for heavy metal removal

The effective removal of toxic heavy metals from environmental samples still remains a major topic of present research. Metal-chelating membranes are very promising materials as adsorbents when compared with conventional beads because they are not compressible, and they eliminate internal diffusion limitations. The purpose of this study was to evaluate the performance of a novel adsorbent, Procion Green H-4G immobilized poly(hydroxyethylmethacrylate (HEMA)/chitosan) composite membranes, for the removal of three toxic heavy metal ions, namely, Cd(II), Pb(II) and Hg(II) from aquatic systems. The Procion Green H-4G immobilized poly(hydroxyethylmethacrylate/chitosan) composite membranes were characterized by elemental analysis, scanning electron microscopy and Fourier transform infrared (FTIR) spectroscopy. The immobilized amount of the Procion Green H-4G was calculated as 0.018+/-0.003 micromol/cm(2) from the nitrogen and sulphur stoichiometry. The adsorption capacity of Procion Green H-4G immobilized poly(hydroxyethylmethacrylate/chitosan) composite membranes for selected heavy metal ions from aqueous media containing different amounts of these ions (30-400mg/l) and at different pH values (2.0-6.0) was investigated. The amount of Cd(II), Pb(II) and Hg(II) adsorbed onto the membranes measured at equilibrium, increased with time during the first 45 min and then remained unchanged toward the equilibrium adsorption. The maximum amounts of heavy metal ions adsorbed were 43.60+/-1.74, 68.81+/-2.75 and 48.22+/-1.92 mg/g for Cd(II), Pb(II) and Hg(II), respectively. The heavy metal ion adsorption on the pHEMA/chitosan membranes (carrying no dye) were relatively low, 6.31+/-0.13 mg/g for Cd(II), 18.73+/-0.37 mg/g for Pb(II) and 18.82+/-0.38 mg/g for Hg(II). Competitive adsorption of the metal ions was also studied. When the metal ions competed with each other, the adsorbed amounts were 12.74+/-0.38 mg Cd(II)/g, 28.80+/-0.86 mg Pb(II)/g and 18.41+/-0.54 mg Hg(II)/g. Procion Green H-4G immobilized poly(hydroxyethylmethacrylate/chitosan) membranes can be regenerated by washing with a solution of nitric acid (0.01 M). The percent desorption achieved was as high as 95%. These novel membranes are suitable for repeated use for more than five adsorption/desorption cycles without any considerable loss in adsorption capacity. Adsorption equilibria were well described by Langmuir equation. It can be concluded that Procion Green H-4G immobilized poly(hydroxyethylmethacrylate/chitosan) membranes may effectively be used for the removal of Cd(II), Pb(II) and Hg(II) ions from aqueous solutions.     

Copper(II)-rubeanic acid coprecipitation system for separation-preconcentration of trace metal ions in environmental samples for their flame atomic absorption spectrometric determinations

A simple and facile preconcentration procedure based on the coprecipitation of trace heavy metal ions with copper(II)-rubeanic acid complex has been developed. The analytical parameters including pH, amounts of rubeanic acid, sample volume, etc. was investigated for the quantitative recoveries of Pb(II), Fe(III), Cd(II), Au(III), Pd(II) and Ni(II). No interferic effects were observed from the concomitant ions. The detection limits for analyte ions by 3 sigma were in the range of 0.14 microg/l for iron-3.4 microg/l for lead. The proposed coprecipitation method was successfully applied to water samples from Palas Lake-Kayseri, soil and sediment samples from Kayseri and Yozgat-Turkey.     

Effect of quaternary ammonium cation loading and pH on heavy metal sorption to Ca bentonite and two organobentonites

Sorption of four heavy metals (Pb, Cd, Zn and Hg) to calcium bentonite (Ca bentonite), hexadecyltrimethylammonium bentonite (HDTMA bentonite) and benzyltriethylammonium bentonite (BTEA bentonite) was measured as a function of the quaternary ammonium cation (QAC) loading at 25, 50 and 100% of the clay's cation-exchange capacity (CEC). The effects of pH on the surface charge of the clays and heavy metal sorption were also measured. Sorption of Cd, Pb, and Zn was non-linear and sorption of all three metals by HDTMA and BTEA bentonites decreased as the QAC loading increased from 25 to 100%. In most cases, sorption of these metals to 25% BTEA and 25% HDTMA bentonite was similar to or greater than sorption to Ca bentonite. Hg sorption was linear for both HDTMA and BTEA bentonite. No significant effect on Hg sorption was observed with increasing QAC loading on BTEA bentonite. However, an increase of Hg sorption was detected with increasing QAC loading on HDTMA bentonite. This behavior suggests that a process different than cation exchange was the predominant Hg sorption mechanism. Cd, Pb, and Zn sorption decreased with pH. However, this effect was stronger for Cd and Pb than Zn. Hg sorption varied inversely with pH. QAC loading affected the surface charge of the clays. Twenty-five and 50% loading of BTEA cations increased the negative charge on the clay's surface relative to the untreated clay, without affecting the zero point of charge (ZPC) of the clay. Increased QAC loading on HDTMA bentonite causes the surface charge to become more positive and the ZPC increased. One hundred percent of HDTMA bentonite maintained a positive surface charge over the range of pH values tested. The organoclays studied have considerable capacity for heavy metal sorption. Given that prior studies have demonstrated the strong sorption capacity of organoclays for nonionic organic pollutants, it is likely that organoclays can be useful sorbents for the treatment of effluent streams containing both organic contaminants and heavy metals.     

Assessing soil heavy metal pollution in the water-level-fluctuation zone of the Three Gorges Reservoir, China

The water-level-fluctuation zone (WLFZ) between the elevations of 145-175 m in China's Three Gorges Reservoir has experienced a novel hydrological regime with half a year (May-September) exposed in summer and another half (October-April) submerged in winter. In September 2008 (before submergence) and June 2009 (after submergence), soil samples were collected in 12 sites in the WLFZ and heavy metals (Hg, As, Cr, Cd, Pb, Cu, Zn, Fe, and Mn) were determined. Enrichment factor (EF), factor analysis (FA), and factor analysis-multiple linear regression (FA-MLR) were employed for heavy metal pollution assessment, source identification, and source apportionment, respectively. Results demonstrate spatial variability in heavy metals before and after submergence and elements of As, Cd, Pb, Cu, and Zn are higher in the upper and low reaches. FA and FA-MLR reveal that As and Cd are the primary pollutants before submergence, and over 45% of As originates from domestic sewage and 59% of Cd from industrial wastes. After submergence, the major contaminants are Hg, Cd, and Pb, and traffic exhaust contributes approximately 81% to Hg and industrial effluent accounts about 36% and 73% for Cd and Pb, respectively. Our results suggest that increased shipping and industrial wastes have deposited large amounts of heavy metals which have been accumulated in the WLFZ during submergence period.     

Vapor generation by UV irradiation for sample introduction with atomic spectrometry

Volatile species of the conventional hydride-forming elements (As, Bi, Sb, Se, Sn, Pb, Cd, Te), Hg, transition metals (Ni, Co, Cu, Fe), noble metals (Ag, Au, Rh, Pd, Pt), and nonmetals (I, S) were generated following UV irradiation of their aqueous solutions to which low molecular weight carboxylic acids (formic, acetic, propionic) had been added. Free radicals arising from photodissociation of the latter provide a new and useful alternative to the common methods of chemical/electrochemical vapor generation techniques for the determination of these analytes by atomic spectrometry. Quantitative estimates of the efficiencies of these generation processes were not undertaken, although calculated signal-to-background ratios (>1500 for 5 ng/mL As, Sb, Bi, Se, and Te; 20 for 10 ng/mL Sn, Cu, Rh, Au, Pd, Pt, and Cd; 2400 for 1 ng/mL Hg; and 1000 for Co using ICP-TOF-MS detection) do provide clear evidence of the efficacy of this approach for sample introduction. In the case of Ni and Se, the tetracarbonyl and alkylated selenium compounds have been identified, respectively.     

微波消解-电感耦合等离子体发射光谱仪法同时测定藏香中7种重金属元素

对藏香多种重金属元素同时检测的方法较少研究.本文建立了微波消解-电感耦合等离子发射光谱仪(ICP-OES)法同时测定藏香中7种重金属元素(As、Cd、Cr、Cu、Hg、Ni、Pb)的方法.藏香样品在HNO3溶液中120℃加热30 min后采用程序升温在100、120、150、185℃下进行微波消解,消解后的溶液经ICP...     

Poly(ethylene glycol dimethacrylate-n-vinyl imidazole) beads for heavy metal removal

Poly(ethylene glycol dimethacrylate-n-vinyl imidazole) [poly(EGDMA-VIM)] hydrogel (average diameter 150-200 microm) was prepared by copolymerizing ethylene glycol dimethacrylate (EGDMA) with n-vinyl imidazole (VIM). The copolymer hydrogel bead composition was characterized by elemental analysis and found to contain 5 EGDMA monomer units each VIM monomer unit. Poly(EGDMA-VIM) beads had a specific surface area of 59.8 m2/g. Poly(EGDMA-VIM) beads were characterized by swelling studies and scanning electron microscopy (SEM). These poly(EGDMA-VIM) beads with a swelling ratio of 78% were used for the heavy metal removal studies. Chelation capacity of the beads for the selected metal ions, i.e., Cd(II), Hg(II) and Pb(II) were investigated in aqueous media containing different amounts of these ions (10-750 mg/l) and at different pH values (3.0-7.0). Chelation rate was very fast. The maximum chelation capacities of the poly(EGDMA-VIM) beads were 69.4 mg/g for Cd(II), 114.8 mg/g for Pb(II) and 163.5 mg/g for Hg(II). The affinity order on molar basis was observed as follows: Hg(II) > Cd(II) > Pb(II). Chelation behavior of heavy metal ions could be modelled using both the Langmuir and Freundlich isotherms. pH significantly affected the chelation capacity of VIM incorporated beads. Chelation of heavy metal ions from synthetic wastewater was also studied. The chelation capacities are 45.6 mg/g for Cd(II), 74.2 mg/g for Hg(II) and 92.5 mg/g for Pb(II) at 0.5 mmol/l initial metal concentration. Regeneration of the chelating-beads was easily performed with 0.1 M HNO3. These features make poly(EGDMA-VIM) beads potential candidate adsorbent for heavy metal removal.     

Geochemical speciation and risk assessment of heavy metals in the river estuarine sediments--a case study: Mahanadi basin, India

Sequential extraction technique was used to study the mobility and dynamics of operationally determined chemical forms of heavy metals in the sediments and their ecological risk on the biotic species. The results reveal that high environmental risk of Cd, Ni, Co and Pb, are due to their higher availability in the exchangeable fraction. Substantial amount of Cd, Co, Mn, Cu, Zn, Ni and Pb, is observed as carbonate bound, which may result due to their special affinity towards carbonate and their co-precipitation with its minerals. Colloids of Fe-Mn oxides act as efficient scavengers for the heavy metals like Zn, Pb, Cu, Cr, Co, and Ni. Toxic metals like Ni, Pb and Cd are of concern, which occasionally may be associated with adverse biological effects based on the comparison with sediment quality guidelines (SQGs). The risk assessment code (RAC) suggests that the highest mobility of Cd poses a higher environmental risk and also threat to the aquatic biota. Factor analysis reveals that the enrichment of heavy metals in bioavailable fraction is mostly contributed from anthropogenic sources. These contributing sources are highlighted by cluster analysis.     

Assessment of heavy metal contamination and its mobilization from municipal solid waste open dumping site

Influence of heavy metals was investigated by conducting various tests on the samples collected from Nonthaburi dumpsite in Thailand. The heavy metal concentration in the solid waste and its mobility potential based on its binding forms was studied. The sequential extraction method was used to determine the binding forms of metals. From the analysis, Zn was found to be highest concentrated heavy metal compared to Mn, Cu, Cr, Cd, Pb, Ni and Hg in the solid waste. From the sequential extraction, Mn, Zn and Cd mostly found in reducible form, showed its susceptibility to be leached easily. Cu and Cr were found predominantly in oxidizable form and stable under anaerobic condition. Pb and Ni were present in residual form, which is inert. The estimated individual contamination factor (C(f)(i)), showed Zn with highest affinity to leach. The concentration level of all the heavy metals in the leachate except for Cr was noticed to be below the National effluent standards. Though, indicated to be safe for disposal, its effect in any concentration proved toxic to the plant life from the seed germination toxicity test using synthetic chelate ethylene diamine tetraacetic acid (EDTA).     

Fate of heavy metals during municipal solid waste incineration in Shanghai

The transfer behavior of heavy metals during municipal solid waste (MSW) incineration was investigated based on 2-year field measurements in two large-scale incinerators in Shanghai. Great temporal and spatial diversification was observed. Most of Hg and Cd were evaporated and then removed by air pollution control (APC) system through condensation and adsorption processes, thus being enriched in the fine APC residues particles. Cr, Cu, and Ni were transferred into the APC residues mainly by entrainment, and distributed uniformly in the two residues flows, as well as in the ash particles with different sizes. Pb and Zn in the APC residues were from both entrainment and evaporation, resulting in the higher concentrations (two to four times) compared with the bottom ash. Arsenic was transported into the flue gas mainly by evaporation, however, its transfer coefficient was lower. Though the heavy metals contents in the APC residues were higher than that in bottom ash, more than 80% of As, Cr, Cu, and Ni, 74-94% of Zn, as well as 46-79% of Pb remained in the bottom ash, due to its high mass ratio (85-93%) in the residues. While 47-73% of Cd and 60-100% of Hg were transferred into the APC residues, respectively.     

Preconcentration of Pb(II), Cr(III), Cu(II), Ni(II) and Cd(II) ions in environmental samples by membrane filtration prior to their flame atomic absorption spectrometric determinations

A method for separation-preconcentration of Pb(II), Cr(III), Cu(II), Ni(II) and Cd(II) ions by membrane filtration has been described. The method based on the collection of analyte metal ions on a cellulose nitrate membrane filter and determination of analytes by flame atomic absorption spectrometry (FAAS). The method was optimized for several parameters including of pH, matrix effects and sample volume. The recoveries of analytes were generally in the range of 93-100%. The detection limits by 3 sigma for analyte ions were 0.02microgL(-1) for Pb(II), 0.3microgL(-1) for Cr(III), 3.1microgL(-1) for Cu(II), 7.8microgL(-1) for Ni(II) and 0.9microgL(-1) for Cd(II). The proposed method was applied to the determination of lead, chromium, copper, nickel and cadmium in tap waters and RM 8704 Buffalo River Sediment standard reference material with satisfactory results. The relative standard deviations of the determinations were below 10%.