共查询到20条相似文献,搜索用时 109 毫秒
1.
通过对昆钢试验生产的HRB400细晶粒热轧带肋钢筋的自然时效和人工时效性能试验分析,得出昆钢生产的HRB400细晶粒钢筋时效后力学性能呈一定的规律性变化,主要表现为钢筋时效后屈服强度有一定下降,抗拉强度的变化不明显,伸长率平均升高了3个百分点,时效不影响钢筋的使用,并且自然时效后,钢筋的综合性能得到了提高. 相似文献
2.
3.
4.
英标460MPa级钢筋余热处理工艺研究 总被引:1,自引:0,他引:1
以Q235、20MnSi钢坯为原料进行了用余热处理工艺生产英标460MPa级钢筋的试验,研究了水冷段数、水压、上冷床温度以及成分、钢种和时效对钢筋性能的影响。结果表明,Q235和20MnSi钢都可以利用余热处理工艺生产出性能合格的钢筋,但前者的生产成本较低;水压减小,钢筋强度降低,上冷床温度越高,强度越低,推荐5段水冷器全开,水压均为1.8~2.0MPa,Q235钢筋的上冷床温度应控制在650℃以下;钢筋典型的金相组织(Q235)表层为回火索氏体,过渡层为珠光体+铁素体且部分铁素体呈针状,心部为珠光体+铁素体,晶粒度8~10级;自然时效后屈服强度下降10~20MPa,用人工时效可以模拟自然时效,工艺是100℃×2h或200℃×1h。 相似文献
5.
6.
本针对HRB335带肋钢筋的屈服不明显的现象,从金属的微观组织、人工时效、自然时效、测试方法等方面着手,寻求各因素对钢筋力学性能的影响,并阐述了该异常组织的形成机理及相关因素,指出魏氏体、马氏体、粒状贝氏体的存在是造成HRB335带肋钢筋性能异常的主要原因,同时对部分屈服不明显的带肋钢筋判定提供较为科学的依据。 相似文献
7.
热轧带肋钢筋屈服不明显原因分析与探讨 总被引:1,自引:0,他引:1
陈洪文 《金属材料与冶金工程》2004,32(2):18-21
针对涟钢热轧带肋钢筋的屈服不明显现象,从金属的金相组织、人工时效、自然时效、测试方法等方面着手,寻求各因素对钢筋力学性能的影响,并阐述了该异常组织的形成机理及相关因素,指出魏氏体、粒状贝氏体等的存在是造成带肋钢筋性能异常的主要原因,同时对部分屈服不明显的带肋钢筋判定提供了较为科学的依据。 相似文献
8.
20MnSiV抗震钢筋的性能及钒的析出分析 总被引:1,自引:0,他引:1
对Φ28mm 钢筋进行了拉伸、焊接、应变时效以及夏氏冲击试验,并通过 TEM 对钢筋中 V 的析出物进行分析。结果表明:钢筋的强度较高,塑性有待于提高;焊接钢筋拉伸强度达到基体水平,弯曲试验焊缝没有出现裂纹;热轧态钢筋和应变时效钢筋低温韧性较好,韧脆转变温度较低;轧后冷却速度较快,冷却时间短,热轧钢筋中 V 的析出物较少。 相似文献
9.
10.
11.
12.
热轧带肋钢筋的矫直工艺研究 总被引:1,自引:1,他引:0
提出了一种新的热轧带肋钢筋的矫直方式,使得矫直后的钢筋表面无划伤,强度与塑性均有提高,消除了矫直后的钢筋屈服点不明显现象。并对经过不同矫直工艺后的热轧带肋钢筋的金相组织分布、力学性能进行了研究。 相似文献
13.
This paper examines the behavior of Eurocrete fiber-reinforced polymer (FRP) bars (glass, carbon, aramid, and hybrid) in concrete under direct pullout conditions. More than 130 cube specimens were tested in direct pullout where no splitting was allowed to develop. In normal concrete, the mode of bond failure of FRP bars was found to differ substantially from that of deformed steel bars because of damage to the resin rich surface of the bar when pullout takes place. Bond strengths developed by carbon fiber-reinforced polymer and glass fiber-reinforced polymer bars appear to be very similar and just below what is expected from deformed steel bars under similar experimental conditions. The load slip curves highlight some of the fundamental differences between steel and FRP materials. This paper reports in detail on the influence of various parameters that affect bond strength and development such as the embedment length, type, shape, surface characteristics, and diameter of the bar as well as concrete strength. The testing arrangement is also shown to influence bond strength because of the “wedging effect” of the bars. 相似文献
14.
阐述了中国建筑钢筋性能升级与使用功能化的重要意义,指出建筑钢筋的性能升级与使用功能化应该走节约型的道路。概述了国内外建筑用热轧带肋钢筋降低生产成本、提高强度、提高使用寿命和使用安全性的发展趋势。分析讨论了目前中国建筑钢筋研究开发、生产应用等方面存在的问题,如:性能低、资源、能源消耗过高、功能性钢筋研究和应用方面落后、标准体系还不完善等。并且提出了促进中国建筑钢筋升级换代的措施与建议。 相似文献
15.
喷射混凝土具有较高的强度和耐久性,与已施工的混凝土和钢筋具有强的粘结力,可用于建筑物梁柱的补强作业。 相似文献
16.
采用显微镜技术和腐蚀速度测量法研究S400、表面预淬火的S500、含钒的S500 3种钢筋暴露在大气中的抗腐蚀行为.同时还研究了在水泥水合作用过程中,水泥与钢筋之间的结合力对钢筋腐蚀的影响.实验结果表明,具有较高抗大气腐蚀能力的钢筋类型是含钒的S500.相反,抗腐蚀能力最小的是表面预先淬火的S500钢筋.从ESEM观测到的形貌和钢筋表面的铁锈层的厚度结果看,钢筋与混凝土之间的结合力随侵蚀时间(从45天~122天)的延长而减小. 相似文献
17.
18.
Ahmed S. Debaiky Gilbert Nkurunziza Brahim Benmokrane Patrice Cousin 《Canadian Metallurgical Quarterly》2006,10(5):370-380
The long-term behavior of glass fiber-reinforced polymer (GFRP) reinforcing bars is one of the most critical issues for the acceptance of these materials as reinforcement for concrete structures. There is a high demand for experimental studies to investigate the stability of the tensile strength, ultimate elongation, and elasticity modulus. GFRP reinforcing bars inherently have a low elasticity modulus, which must not significantly decrease over time under loading or the serviceability behavior of the concrete element containing them will be jeopardized. This paper evaluates the residual tensile properties of three sizes of sand-coated GFRP reinforcing bars in alkaline and water environments combined with sustained loading and elevated temperature. Bar diameters of 15.9 (No. 5), 12.7 (No. 4), and 9.5?mm (No. 3) were loaded for different durations, then tested in axial tension for residual tensile properties. The test periods varied from 1?to?4?months under elevated temperature to hasten degradation and simulate extended service periods. The reduction in tensile strength was found to be 7–13% of the guaranteed strength for the three bar sizes under elevated temperature, which is at least 26% higher than the specified design strength as recommended by ACI 440.1R-03. More importantly, no significant change in the elastic modulus was observed. 相似文献
19.