High-performance monolithically integratedIn0.53Ga0.47As/InP p-i-n /JFET optical receiverfront-end with adaptive feedback control

An optical transimpedance receiver front-end that is adaptable to a wide range of bit-rates up to 3 Gb/s has been realized by monolithically integrating high efficiency p-i-n photodiodes with low noise InGaAs junction field effect transistors. The transimpedance-bandwidth product of the receiver is 2.8 THz Ω. The average equivalent input noise current for full circuit bandwidth is 4.0 pA/√Hz. The preamplifier for nonreturn to zero data transmission without equalization of the frequency response at 1.55 μm offers a sensitivity of -41.5 dBm and -29.5 dBm at 140 Mb/s and 2.4 Gb/s, respectively. The dynamic range is 17 dB at 2.4 Gb/s and exceeds 30 dB at 500 Mb/s     

1 Gb/s operation and bit-error rate studies of FET-SEEDdiode-clamped smart-pixel optical receivers

Experimental studies of the bit-error rate (BER) of diode-clamped optical receivers based on FET-SEED technology are described. 1 Gb/s operation of a receiver with optical input and electrical output is obtained. A strong dependence of the BER on clamping voltage is reported, confirming the digital nature of the receiver. The best receiver sensitivity measured at 1 Gb/s and an error rate of 1×10 ^-9 is roughly -11 dBm. At 622 Mb/s, it is -22 dBm     

16 Gbit/s transmission experiments using a directly modulated 1.3μm DFB laser

A 16 Gb/s electrically time-division-multiplexed lightwave link is discussed. The 16 Gb/s electronic signal was generated by multiplexing together eight copies of the 2-Gb/s pseudorandom sequence (length 2¹⁵-1) produced by a commercial BER test set. A 22-km transmission distance was achieved using a directly modulated, 1.3-μm wavelength DFB laser and a 50-Ω p-i-n receiver. Receiver sensitivity for a BER of 10^-9 was -2.0 dBm. The addition of an optical preamplifier required a more sensitive receiver to avoid saturation-induced distortion in the preamplifier. This was accomplished by reducing the 2-Gb/s word length to 24 b, thereby lowering the intersymbol interference penalty and effectively increasing the receiver sensitivity. Under these conditions, the optical preamplifier receiver sensitivity was -19 dBm, and a 64.5-km transmission was demonstrated     

High-speed monolithic silicon photoreceivers on high resistivityand SOI substrates

We compare monolithic silicon optical receivers fabricated on high resistivity and silicon-on-insulator (SOI) substrates. Each receiver consisted of a lateral p-i-n photodiode and an NMOS transimpedance preamplifier. At a drain voltage (V_DD) of 3.5 V, a photodiode voltage (V_PD) of 30 V, and a wavelength of 850 nm, the high resistivity receiver exhibited sensitivities of -31.9 dBm at 622 Mb/s and -23.2 dBm at the maximum operating speed of 1.0 Gb/s. At V_DD =5 V and V_PD=20 V, the sensitivity of the SOI receiver was -26.1 dBm at 622 Mb/s, -20.2 dBm at 1.0 Gb/s and -12.2 dBm at the maximum speed of 2.0 Gb/s. Single supply operation at 5 V and 3 V was also demonstrated for the SOI receiver. Methods for extending the speed and improving the sensitivity characteristics in more advanced technologies with lower supply voltages are discussed     

Multigigabit/s 1.5 μm λ/4-shifted DFB OEIC transmitterand its use in transmission experiments

Optoelectronic integrated circuit (OEIC) transmitters consisting of 1.5 μm λ/4-shifted distributed feedback (DFB) lasers and InGaAs-InAlAs MODFETs were fabricated for the first time. The entire processing requires only two organometallic vapor-phase epitaxy (OMVPE) growths, with the potential for high yield and low cost. Direct modulation of the OEIC transmitter is demonstrated for bit rates up to 10 Gb/s. A transmission experiment using the OEIC transmitter and a hybrid p-i-n/HEMT receiver is conducted at 5 Gb/s, with a sensitivity of -20 dBm and a bit-rate-distance product of 145 Gb/s-km     

Modulation and demodulation techniques in optical heterodyne PSKtransmission systems

Modulation and demodulation techniques are described for an optical PSK heterodyne transmission system operating at 560 Mb/s and 1.2 Gb/s. Performance limitations affecting the receiver sensitivity in a 1.2-Gb/s DPSK system, such as laser phase noise, phase modulation depth, IF center frequency deviation, and local laser power, are studied. High receiver sensitivities for PSK systems were achieved. The applicability of the Mach-Zehnder modulator as a phase modulator for 1.2-Gb/s DPSK is also demonstrated. A 1.2-Gb/s DPSK transmission of over 100 km, using polarization diversity with novel polarization-insensitive automatic frequency control in an attempt to overcome signal fading caused by polarization fluctuation in the transmitting fiber, is also described. A receiver sensitivity of less than -42.8 dBm and varying within 1.4 dB for all states of polarization was achieved. A multichannel high-definition TV (HDTV) transmission experiment using a DPSK polarization-diversity tunable receiver is described     

622Mb／s光接收机

本文介绍的光接收机码率为６２２Ｍｂ／ｓ，接收灵敏度为－３１ｄＢｍ、符合ＣＣＩＴＴ关于光同步数字传输网的Ｇ．９５７标准。以此接收机进行了１１０公里的光纤传输试验，连续８小时实测误码为零。     

The STARNET coherent WDM computer communication network:experimental transceiver employing a novel modulation format

We have designed, constructed, and investigated an experimental transceiver employing a novel combined PSK and ASK modulation format for the STARNET coherent WDM computer communication network. Using this experimental transceiver, we show that it is possible to transmit and receive 2.488 Gb/s PSK circuit-switched data and 125 Mb/s ASK packet-switched data on the same lightwave. The experimental transceiver employs a custom integrated-optic LiNbO₃ modulator with both phase and amplitude sections, a 2.488 Gb/s tunable PSK heterodyne receiver, and a 125 Mb/s ASK heterodyne receiver. Both receivers function properly with error rates less than 10^-9 and a sensitivity of -32.1 dBm; the corresponding optimum ASK modulation depth is 0.57. The resulting network power budget is 26.6 dB     

DC-1 Gb/s burst-mode compatible receiver for optical busapplications

The characteristics and performance of a high-speed, burst-mode compatible receiver for optical bus or packet communications are described. It employs an Si bipolar differential transimpedance amplifier, an auto-threshold tracking level control circuit, and a DC-coupled decision circuit (ECL compatible quantizer). To cope with intermittent data packets, the threshold control circuit can capture data amplitude and set the logic threshold in about 1 ns. Using an avalanche photodiode, the typical receiver sensitivity is -37.5 dBm (10 ^-9 BER) at bit rates up to 900 Mb/s, with a dynamic range of 23 dB for both pseudorandom and burst-mode signals. At 1 Gb/s, the sensitivity is -35 dBm. With a worst-case reset time <100 ns for the threshold control circuit, this receiver can be used for optical bus applications where data signals with varying optical power are employed     

Demonstration of 20-Gb/s DQPSK With a Single Dual-Drive Mach–Zehnder Modulator

Using a single, dual-drive Mach-Zehnder modulator and high-speed electronics, differential quadrature phase-shift keying modulation and detection are demonstrated for a bit rate of 20 Gb/s. Back-to-back system performance is measured, and the receiver sensitivity is found to be -32.25 dBm.     

1 Gbit/s bipolar optical FSK transmission experiment over 121 km offibre

Bipolar direct modulation has been used to overcome the nonuniform low-frequency modulation response of a DFB laser transmitter in a 1 Gbit/s optical FSK transmission system. The heterodyne receiver sensitivity (nP¯) was -39 dBm for a 2²³-1 bit pseudorandom pattern, with no degradation in receiver sensitivity after transmission through 121 km of fibre     

All-silicon IC 10 Gb/s optical receiver

A fully integrated 10 Gb/s optical receiver was realized with silicon ICs. The receiver was fabricated on a breadboard utilizing multicarrier assembly. Receiver sensitivity of -29.3 dBm was achieved using an Er-doped optical fiber preamplifier     

Signal generation and transmission at 40, 80, and 160 Gb/s using a fiber-optical parametric pulse source

Short return-to-zero pulses (/spl sim/2 ps) are generated at bit rates of 40, 80, and 160 Gb/s using a fiber-optical parametric amplifier. The performance of the parametric pulse source is evaluated both back-to-back and in a 110-km transmission link. A receiver sensitivity of -33 dBm back-to-back was achieved after demultiplexing from 160 to 10 Gb/s. The power penalty at 160 Gb/s due to 110-km transmission was less than 2 dB. Very short pulses (0.5 ps) were also achieved when using the parametric amplifier as a compressor.     

2.488 Gb/s-318 km repeaterless transmission using erbium-dopedfiber amplifiers in a direct-detection system

The authors have achieved a 2.488 Gb/s, 318 km repeaterless transmission without any fiber dispersion penalty through a nondispersion-shifted fiber in a direct detection system. The system was loss limited with a T-R power budget of 57 dB. Three key components enabled the authors to achieve this result: (1) a Ti:LiNbO₃ external amplitude modulator enabling a dispersion-free transmission, (2) erbium-doped fiber amplifiers increasing the transmitting power to +16 dBm, and (3) an erbium-doped fiber preamplifier enabling a high-receiver sensitivity of -4.1 dBm for 10^-9 BER. To the author's knowledge, this result is the longest repeaterless transmission span length ever reported for direct detection at this bit rate. From the experimental results and a theoretical model, the authors identified the sources of the receiver sensitivity degradation from the quantum limit (-48.6 dBm) and estimated the practically achievable receiver sensitivity of ~-44 dBm (~-124 photons/bit) for 2.5 Gb/s optical preamplifier detection     

Rayleigh scattering influence on performance of 10 Gb/s opticalreceiver with Er-doped optical fiber preamplifier

The achievement of -30.8 dBm (630 photon/bit) receiver sensitivity at 10 Gb/s, with an Er³⁺-doped optical fiber preamplifier, is discussed. This is an 8.3-dB sensitivity improvement over the avalanche-photodiode/FET receiver. Power penalties caused by a noise increase due to Rayleigh backscattering by the transmission optical fiber have been evaluated. Approximately -30-dB Rayleigh scattering from a 20-km optical fiber resulted in a 3.5-dB power penalty for a 25-dB-gain optical amplifier     

70-Gb/s amplitude-shift-keyed system with 10-GHz clock recovery circuit using duty cycle division multiplexing

The performance of ASK over DCDM for up to seven channels is reported. The aggregate bit rate of 70 Gb/s is achieved with only 160-GHz modulation bandwidth. The clock and data recovery are realized at 10-GHz clock rate, which is very economic and efficient. At 7 × 10 Gb/s, the worst receiver sensitivity of −10 dBm, OSNR of 41.5 dB and chromatic dispersion tolerance of ±7 ps/nm are achieved. Whereas, for the best channel, the receiver sensitivity, OSNR, and chromatic dispersion tolerance are −23.5 dBm, 29 dB, and ±36 ps/nm, respectively.     

A 10 Gb/s high sensitivity, monolithically integrated p-i-n-HEMToptical receiver

A high-sensitivity, monolithically integrated optical receiver, composed of a p-i-n-PD and high electron mobility transistors (p-i-n-HEMTs) is described. The receiver sensitivity is -17.3 dBm at a bit error rate of 1×10^-9 for a 10-Gb/s non-return-to-zero (NRZ) lightwave signal. This value is the best result yet reported for 10-Gb/s monolithically integrated receivers. The sensitivity is -30.6 dBm if an erbium-doped fiber amplifier (EDFA) is placed ahead of the p-i-n-NEMT receiver. A transmission experiment using a 150-km dispersion-shifted fiber (DSF) indicates no degradation in the bit error rate characteristics or the eye pattern. This verifies the practicality of the p-i-n-HEMT optical receiver for high-speed transmission systems     

多速率接收及时钟数据恢复光纤激光传输实验研究

基于84km光传输链路,对L波段光纤激光器进行了多速率接收及时钟数据恢复实验。采用伪随机序列非归零(NRZ)码、高性能LiNbO3电光晶体调制器,调制速率从622Mb/s到2.7Gb/s。实验所用光纤激光器输出中心波长1 610.28nm,线宽0.1nm,边模抑制比大于45dB,输出功率稳定性优于0.02dB。对多速率接收眼图进行了测试,其各速率信号眼图张开度好、眼皮厚度小,结果表明测试系统无码间干扰和信号畸变,信号的信噪比较高。在误码率为10-12时,接收灵敏度可达到-30.62dBm,过载光功率为-4.1dBm。分析了影响系统传输质量的因素,研究了高速率下信号与时钟恢复后不同步的问题。     

A transimpedance APD optical receiver operating at 10 Gb/s

The authors report an optical receiver which uses a separate-absorption-and-multiplication avalanche photodiode (SAM-APD) to achieve high sensitivity at a bit rate of 10 Gb/s. A transimpedance front end incorporating HEMT devices is used for high bandwidth and low noise. The sensitivity (bit-error rate of 10^-9) is -28.7 dBm for a return-to-zero signal, and -27.0 dBm for a nonreturn-to-zero signal     

Optical phase-locked PSK heterodyne experiment at 4 Gb/s

A 4 Gb/s phase-locked optical PSK (phase shift keying) heterodyne communication system is demonstrated. The receiver was implemented with a single 100-Ω loaded p-i-n photodiode and a 1320-nm diode-pumped miniature Nd:YAG laser as a local oscillator. For a 2⁷-1 PRBS (pseudorandom bit sequence), the receiver sensitivity was -34.2 dBm or 631 photons/bit. The corresponding power on the surface of the detector was -37.3 dBm or 309 photons/bit. With a 2¹⁵-1 PRBS, a 2.6 dB additional sensitivity degradation was observed due to the nonideal frequency response of the phase modulator and the receiver amplifiers