Behavior of FRP Strengthened Infill Walls under In-Plane Seismic Loading

The present paper investigates the suitability and effectiveness of fiber-reinforced polymers (FRP) in strengthening and/or repairing unreinforced masonry infill walls in reinforced concrete frames which are subjected to in-plane seismic/cyclic loading. For this purpose, a detailed experimental program was conducted. Specimen geometry, test setup, instrumentation, and a loading procedure that simulates earthquake loading are presented in a detailed fashion. Results of experimental observations are discussed in the form of load-displacement hysteretic loops and envelopes; column profiles; strain diagrams, and wall shear distortion. The test results, in general, indicate that the use of glass FRP (GFRP) sheets as strengthening materials provides a degree of enhancement to the infill wall, upgrades its deformation capacity, and makes the wall work as one unit. These results thus show great potential for externally bonded GFRP sheets in upgrading and strengthening the infill walls under in-plane seismic loads.     

组合式钢框架内填预制RC墙结构静力性能有限元分析

钢框架内填预制钢筋混凝土剪力墙结构是新型混合式结构,由钢框架与内填墙组成双重防线,具有良好的抗侧力能力,同时预制构配件和预制装配建筑有利于推动住宅产业化发展.考虑大尺寸内填预制RC墙运输和安装困难的情况,提出竖向和横向组合式钢框架内填RC墙结构,采用ABAQUS建立有限元模型进行结构受力分析.通过分析荷载位移曲线,构件应力分布和变形情况,研究结构破坏特点和受力性能.结果表明,全螺栓结构因其合理的传力路径,有良好的承载力和延性;竖向组合式具有较好的初始刚度和整体承载力,与全螺栓连接预制RC墙有近似的受力性能,便于运输和安装;而横向组合式由于上下板缺乏有效传力路径,初始刚度和最终承载力都明显低于全螺栓和竖向组合式,不利于实际工程应用.      

Assessment of Design Formulas for In-Plane FRP Strengthening of Masonry Walls

Masonry structures have demonstrated their seismic vulnerability during recent world seismic events. This paper investigates in-plane seismic performance of unreinforced masonry (URM) walls before and after they are retrofit using fiber-reinforced polymer (FRP) materials. An assessment of available design formulas for evaluating both the in-plane performance of URM walls and the contribution of FRP strengthening systems was performed. Walls with two configurations of the FRP reinforcement have been analyzed: one based on FRP strips installed parallel to the mortar joints, the other characterized by FRP strips arranged along the diagonals of the wall. Based on shear–compression tests carried out on FRP-strengthened masonry walls available in the literature, a comparison between theoretical and experimental data is performed. A discussion about the FRP strains at failure of the walls is provided and values of effective FRP strains to be used for design purposes are proposed.     

In-Plane Seismic Response of URM Walls Upgraded with FRP

Recent earthquakes have shown the vulnerability of unreinforced masonry (URM) buildings, which have led to an increasing demand for techniques to upgrade URM buildings. Fiber reinforced polymer (FRP) can provide an upgrading alternative for URM buildings. This paper presents results of dynamic tests investigating the in-plane behavior of URM walls upgraded with FRP (URM-FRP). These tests represent pioneer work in this area (dynamic and in-plane). Five half-scale walls were built, using half-scale brick clay units, and upgraded on one face only. Two moment/shear ratios (1.4 and 0.7), two mortar types (M2.5 and M9), three composite materials (carbon, aramid, and glass), three fiber structures (plates, loose fabric, and grids), and two upgrading configurations (diagonal “X” and full surface shapes) were investigated. The test specimens were subjected to a series of synthetic earthquake motions with increasing intensities on a uniaxial earthquake simulator. The tests validate the effectiveness of the one side upgrading: the upgrading technique improved the lateral resistance of the URM walls by a factor ranging from 1.3 to 2.9; however, the improvement in the lateral drift was less significant. Moreover, no uneven response was observed during the test due to the single side upgrading. Regarding the upgrading configurations, the bidirectional surface type materials (fabrics and grids) applied on the entire surface of the wall (and correctly anchored) can help postpone the three classic failure modes of masonry walls: rocking (“flexural failure”), step cracking, and sliding (“shear failures”). Additionally, in some situations, they will postpone collapse by “keeping the bricks together” under large seismic deformations. On the other hand, the diagonal “X” shape was less successful and premature failure was developed during the test.     

Nonlinear Behavior of a Masonry Subassemblage Before and After Strengthening with Inorganic Matrix-Grid Composites

Past experimental tests on a full-scale masonry wall with an opening evidenced the key role of the spandrel panel in the in-plane nonlinear response of the system. Recent seismic codes do not provide specific criteria to assess and to strengthen existing masonry spandrel panels with inorganic matrix-grid (IMG) composites. Numerical finite-element (FE) analyses are used to deepen the knowledge about the nonlinear response of masonry walls and the role of the IMG strengthening system. The comparison of experimental and numerical results contributes to the development of a simplified analytical model to assess the influence of the external reinforcement system on the in-plane seismic response of masonry wall systems. Some hints about the strengthening design that could change the failure mode from brittle shear to ductile flexure are given. Finally, a further enhancement of the IMG strengthening system is proposed to avoid the undesirable splitting phenomena attributable to compression forces and to exploit the full compressive strength of masonry against bending moments.     

轻质混凝土拼装墙板填充钢框架协同抗震性能试验研究

为了研究墙板与钢框架结构之间的协同抗震性能,对采用不同墙框连接节点的轻质混凝土拼装墙板填充钢框架进行了低周往复荷载试验。通过对比试件的承载力、滞回性能、刚度、耗能以及延性性能,探讨了轻质混凝土拼装墙板及其整体性对结构抗震性能的影响。结果表明:填充墙板钢框架结构的最终破坏形态以墙板挤压开裂,框架梁柱端部翼缘屈曲为主;轻质混凝土拼装墙板与钢框架协同工作,有利于提高结构整体的承载力和变形能力,减轻钢框架在平面内的屈曲破坏;与刚性节点相比,采用柔性节点连接墙板与钢框架对结构的承载力、层间刚度和耗能能力更为有利;增强拼装墙板的整体性,有助于提高结构整体刚度、变形和耗能能力。研究结果可为轻质混凝土拼装墙板填充钢框架结构的抗震设计提供参考。      

Concept and Finite-Element Modeling of New Steel Shear Connectors for Self-Centering Wall Systems

Self-centering precast concrete walls have been found to provide excellent seismic resistance. Such systems typically exhibit low energy dissipation, requiring supplementary dissipating components to improve their seismic performance. Mild steel shear connectors can provide an economical energy dissipating element. The design and analysis of steel shear connectors for a new precast wall system has been undertaken. A series of finite-element analyses were conducted to investigate the behavior of different types of connectors. Emerged from these analyses is a oval-shaped connector (O-connector) that provided satisfactory force-displacement behavior and appeared well suited for the new wall system in high seismic regions. An extensive experimental test program was then conducted to verify the performance of the chosen O-connector, which confirmed the expected response with sufficient energy dissipation. The experimental data demonstrated good correlation with the finite-element model developed, providing satisfactory confidence in the finite-element technique used for the development of the different connectors.     

CFRP Composite Connector for Concrete Members

Steel plate connections are frequently used in tilt-up and precast concrete building construction to tie adjacent wall panels together for shear and overturning effects, and to provide continuous diaphragm chord connections for wind and seismic loading. These welded connectors perform poorly in regions of high seismicity and are vulnerable to corrosion. Until now, retrofit and repair strategies for in-plane shear transfer strengthening were limited to attaching steel sections across panel edges. In the present paper, an experimental program is described that utilizes carbon fiber reinforced plastic (CFRP) composites to develop a viable retrofit scheme for precast concrete shear walls and diaphragms. Nine full-scale precast wall panel assemblies with CFRP composite connectors have been tested. The results show that the CFRP composite connection is an effective solution for the seismic retrofit and repair of precast concrete wall assemblies and other precast concrete elements, such as horizontal diaphragms, that require in-plane shear transfer strengthening.     

Dynamic Racking Crescendo Tests on Architectural Glass Fitted with Anchored Pet Film

Results are presented of a pilot study conducted recently at the Pennsylvania State University Building Envelope Research Laboratory (BERL) to investigate the response of curtain wall mock-ups glazed with 6 mm (? in.) annealed monolithic architectural glass panels fitted with anchored applied film under simulated earthquake conditions. Three common film-to-frame anchoring methods were evaluated: (1) structural silicone adhesive [13 mm (? in.) triangular cross section] application along the entire glass panel perimeter; (2) an aluminum bar extrusion to anchor the film to the frame horizontal along only the top of the glass panel; and (3) two aluminum bar extrusions to anchor the film to the frame verticals along the two vertical edges of the glass panel. Serviceability (glass cracking) and ultimate (glass fallout) limit-state data were collected during in-plane dynamic racking tests. Other performance characteristics, such as cohesive failure of the structural silicone adhesive, loss of film-to-glass adhesion, film tearing, damage to aluminum anchor bars, pullout of the filmed glass unit from the frame glazing pockets, and eventual entire unit fallout, were also recorded. These preliminary tests indicated that anchorage type can demonstrably influence both the serviceability (initial glass cracking) and ultimate (glass fragment fallout and entire unit fallout) limit states of “unweathered” filmed glass panels. In this study, the structural silicone anchor provided the best serviceability limit-state performance of the three anchor methods tested, and the top anchor provided the best entire-unit glass fallout resistance.     

正交胶合木填充墙-钢框架体系受力性能

采用开源地震工程模拟系统（OpenSees）对以正交胶合木作填充墙的钢框架结构进行探索性数值研究,主要研究该填充墙钢框架单元在单调和循环加载作用下的受力性能,墙体与钢框架之间的协同工作性能以及连接个数对整体结构受力性能的影响.结果表明:正交胶合木填充墙能够提高钢框架的抗侧刚度和水平承载力;柔性连接的设置使整体结构耗能性能良好;工作缝的设置减缓墙体的开裂,更大程度上发挥连接件的耗能和变形能力;连接个数对构件的抗侧能力影响较大,可以通过调整连接数量和连接间距设计出具有多种刚度和耗能能力的框架单元.      

Analytical Investigation of Lateral Strength of Masonry Infilled RC Frames Retrofitted with CFRP

In this study, two reinforced concrete frames with hollow clay tile masonry infill walls, retrofitted with diagonally applied carbon fiber-reinforced polymer (CFRP), which were tested previously, were analytically investigated. A simple material model for the masonry infill wall strengthened with CFRP is suggested. The lateral strength of each rehabilitated frame was obtained by pushover analysis of four different models using a commercially available finite-element program, and the results were compared with the test results. We also determined the lateral strength of the CFRP-applied masonry infill walls, and compared the results with the results obtained from existing analytical models. Drift capacity of the masonry infill walls strengthened with CFRP was also investigated, and the drift capacity of the masonry infill walls strengthened with diagonally applied CFRP was recommended. It is concluded that the strength of the masonry infilled frames strengthened with diagonally applied CFRP can be satisfactorily predicted with the suggested procedure. The ultimate drift capacity of the masonry infill walls strengthened with diagonally applied CFRP strips was conservatively predicted to be 1.0%.     

Shear Strengthening Masonry Panels with Sheet Glass-Fiber Reinforced Polymer

This paper investigates strengthening masonry walls using glass-fiber reinforced polymer (GFRP) sheets. An experimental research program was undertaken. Both clay and concrete brick specimens were tested, with and without GFRP strengthening. Single-sided strengthening was considered, as it is often not practicable to apply the reinforcement to both sides of a wall. Static tests were carried out on six masonry panels, under a combination of vertical preload, and in-plane horizontal shear loading. The mechanisms by which load was carried were observed, varying from the initial, uncracked state, to the final, fully cracked state. The results demonstrate that a significant increase of the in-plane shear capacity of masonry can be achieved by bonding GFRP sheets to the surface of masonry walls. The experimental data were used to assess the effectiveness of the GFRP strengthening, and suggestions are made to allow the test results to be used in the design of sheet GFRP strengthening for masonry structures.     

Improved Damage Quantification from Elemental Modal Strain Energy Change

An improved structural damage quantification algorithm is presented based on the elemental modal strain energy change before and after the occurrence of damage in a structure. The algorithm includes the analytical stiffness and mass matrices of the system in the damage quantification. It reduces significantly the modal truncation error and the finite-element modeling error from higher analytical modes in the computation, and it improves the convergence properties of the existing algorithm by Shi et al. (2000). “Structural damage detection from elemental modal strain energy change.” J. Eng. Mech., 126(12), 1216–1223]. The effectiveness of the proposed algorithm is demonstrated via a numerical example and experimental results from a two-storey steel portal frame, and it is demonstrated to be an efficient and robust method for damage quantification.     

Behavior of Composite Unreinforced Masonry–Fiber-Reinforced Polymer Wall Assemblages Under In-Plane Loading

An experimental investigation was conducted to study the in-plane behavior of face shell mortar bedded unreinforced masonry (URM) wall assemblages retrofitted with fiber-reinforced polymer (FRP) laminates. Forty-two URM assemblages were tested under different stress conditions present in masonry shear and infill walls. Tests included prisms loaded in compression with different bed joint orientation (on/off-axis compression), diagonal tension specimens, and specimens loaded under joint shear. The behavior of each specimen type is discussed with emphasis on modes of failure, strength and deformation characteristics. Results showed that the application of FRP laminates on URM has a great influence on strength, postpeak behavior, as well as altering failure modes and maintaining the specimen integrity. The retrofitted specimens reached compressive strength of 1.62–5.64 times that of their unretrofitted counterparts, depending on the bed joint orientation, and joint shear strength increased by eightfold.     

双钢板混凝土组合剪力墙轴压承载力研究

首先对双钢板混凝土组合剪力墙中的钢板进行了屈曲理论分析,对核心受约束混凝土进行了受力分析.以北京中国尊核心筒结构底部剪力墙为原型,进行了1/4缩尺模型的双钢板混凝土组合剪力墙试件和内置钢板混凝土组合剪力墙的轴压性能试验,对比分析其荷载-位移曲线、轴压承载力等.考虑到钢板屈曲对钢板轴压承载力的影响以及受约束混凝土轴心抗压强度的提高,提出了双钢板混凝土组合剪力墙轴压承载力的计算公式,与应用其他计算方法计算得到的试验试件的轴压承载力相比,本文提出的计算公式的计算结果与试验结果吻合度最高.结合其他文献中双钢板混凝土组合剪力墙轴压性能试验的相关数据进行验证,表明利用本论文提出的计算公式得到的轴压承载力计算值与试验结果吻合较好.      

Cyclic Flexure Tests of Masonry Walls Reinforced with Glass Fiber Reinforced Polymer Sheets

The research work reported here investigates the out-of-plane flexural behavior of masonry walls reinforced externally with glass fiber reinforced polymer (GFRP) sheets and subjected to cyclic loading. A full-scale test program consisting of eight wall specimens was conducted. Nine tests were performed, in which three parameters were studied. These included the level of compressive axial load, amount of internal steel reinforcement, and amount of externally bonded GFRP sheet reinforcement. Of the three parameters studied, varying the amount of GFRP sheets was the only parameter that significantly affected the behavior of the walls. The GFRP sheet reinforcement governed the linear response of the bending moment versus centerline deflection hysteresis. Increasing or decreasing the amount of GFRP sheet reinforcement either increased or decreased both the wall stiffness and the ultimate strength, respectively. Except for visible cracks, the walls maintained their structural integrity throughout the out-of-plane cyclic loading. The unloading/reloading paths for successive loading cycles were similar, indicating little degradation. Thus, the general behavior of the walls was very predictable. The system, therefore, could be used to advantageously rehabilitate older masonry structures that are inadequately reinforced to withstand seismic events. A simple model of the behavior is also presented to allow for the evaluation of the strength and deformation characteristics of these elements.     

Performance of Unreinforced Masonry Walls Retrofitted with Externally Anchored Steel Studs under Blast Loading

Six full-scale concrete masonry walls were tested under free-field blast loading using different charge sizes up to 250?kg of ammonium nitrate/fuel oil (ANFO) and at a constant stand-off distance of 15.0?m to cover a wide range of expected damage levels. Five walls were retrofitted with cold-formed steel studs anchored to the wall backs and were compared to the remaining as-built wall. Significant enhancement to the out-of-plane blast resistance of the retrofitted walls, compared to the as-built wall, was observed. This enhancement is attributed to the development of a tied-arch action in the retrofitted walls in which the masonry forms a compression strut while the steel studs serve as the tie. A simplified single-degree-of-freedom model was used to analyze the experimental results, and the model results agreed well with the observed damage levels and the resistances of the walls. In addition, the effectiveness of the proposed retrofit technique was evaluated in terms of strength enhancement and wall deflection reduction. The test results were also compared with those predicted by available blast damage assessment models for unreinforced masonry walls. However, it was found that available models, which do not account for the tied-arch mechanism, greatly underestimate the actual blast capacity of the retrofitted walls because of the assumption of a tensile flexural failure mode. Additionally, the proposed retrofit technique shifts the mode of failure from flexure to shear.     

Optimum Design for External Seismic Stability of Geosynthetic Reinforced Soil Walls: Reliability Based Approach

In this paper, an analytical study considering the effect of uncertainties in the seismic analysis of geosynthetic-reinforced soil (GRS) walls is presented. Using limit equilibrium method and assuming sliding wedge failure mechanism, analysis is conducted to evaluate the external stability of GRS walls when subjected to earthquake loads. Target reliability based approach is used to estimate the probability of failure in three modes of failure, viz., sliding, bearing, and eccentricity failure. The properties of reinforced backfill, retained backfill, foundation soil, and geosynthetic reinforcement are treated as random variables. In addition, the uncertainties associated with horizontal seismic acceleration and surcharge load acting on the wall are considered. The optimum length of reinforcement needed to maintain the stability against three modes of failure by targeting various component and system reliability indices is obtained. Studies have also been made to study the influence of various parameters on the seismic stability in three failure modes. The results are compared with those given by first-order second moment method and Monte Carlo simulation methods. In the illustrative example, external stability of the two walls, Gould and Valencia walls, subjected to Northridge earthquake is reexamined.     

Elastic-Plastic Seismic Behavior of Long Span Cable-Stayed Bridges

This paper investigates the elastic-plastic seismic behavior of long span cable-stayed steel bridges through the plane finite-element model. Both geometric and material nonlinearities are involved in the analysis. The geometric nonlinearities come from the stay cable sag effect, axial force-bending moment interaction, and large displacements. Material nonlinearity arises when the stiffening steel girder yields. The example bridge is a cable-stayed bridge with a central span length of 605 m. The seismic response analyses have been conducted from the deformed equilibrium configuration due to dead loads. Three strong earthquake records of the Great Hanshin earthquake of 1995 in Japan are used in the analysis. These earthquake records are input in the bridge longitudinal direction, vertical direction, and combined longitudinal and vertical directions. To evaluate the residual elastic-plastic seismic response, a new kind of seismic damage index called the maximum equivalent plastic strain ratio is proposed. The results show that the elastic-plastic effect tends to reduce the seismic response of long span cable-stayed steel bridges. The elastic and elastic-plastic seismic response behavior depends highly on the characteristics of input earthquake records. The earthquake record with the largest peak ground acceleration value does not necessarily induce the greatest elastic-plastic seismic damage.     

Unreinforced Concrete Masonry Walls Strengthened with CFRP Sheets and Strips under Pendulum Impact

Impact tests using drop-weight pendulum on nine 1.2-m-high full-scale concrete masonry block walls were conducted to investigate the out-of-plane impact behavior of unreinforced masonry (URM) walls externally strengthened with carbon-fiber-reinforced polymer (CFRP) composites. Three strengthening schemes on one side of the wall were studied: continuous unidirectional and continuous woven sheets, discrete strips in a vertical pattern, and discrete strips in orthogonal and diagonal patterns. All walls were vertically positioned resting on a knife-edge support with one face leaning against two steel rollers close to the upper and lower edges of the wall. The impact load was applied at the wall center through a drop-weight pendulum impact tester with various drop heights. Test results revealed that using composite laminates or strips could significantly improve the impact performance of URM walls. The wall strengthened with continuous woven sheets performed better than the one with unidirectional sheet. With the same amount of fiber-reinforced polymer strip material, the wall with narrower but more closely spaced strips performed slightly better than the one with wider strips.