六元环型磺化聚酰亚胺类质子交换膜

磺化聚酰亚胺是一类很有希望在燃料电池中获得应用的质子交换膜材料。本文对近年来六元环型磺化聚酰亚胺的制备、磺化聚酰亚胺质子交换膜的各项性能做了一定的归纳与分析。重点介绍了耐水性、耐久性、离子交换容量、质子电导率四个方面的测试方法及影响因素,指出目前存在的问题并预测了今后重点研究的方向。     

Partially Sulfonated Poly(1,4‐phenylene ether‐ether‐sulfone) and Poly(vinylidene fluoride) Blend Membranes for Fuel Cells

Blend membranes based on high conductive sulfonated poly(1,4‐phenylene ether‐ether‐sulfone) (SPEES) and poly(vinylidene fluoride) (PVDF) having excellent chemical stability were prepared and characterized for direct methanol fuel cells. The effects of PVDF content on the proton conductivity, water uptake, and chemical stability of SPEES/PVDF blend membranes were investigated. The morphology, miscibility, thermal, and mechanical properties of blend membranes were also studied by means of scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA) measurements. The blend membrane containing 90 wt.% SPEES (degree of sulfonation – DS = 72%) and 10 wt.% PVDF (M_w = 180,000) exhibits optimum properties among various SPEES72/PVDF membranes. Addition of PVDF enhanced resistance of the SPEES membrane against peroxide radicals and methanol significantly without deterioration of its proton conductivity. It's proton conductivity at 80 °C and 100% relative humidity is higher than Nafion 115 while it's methanol permeability is only half of that of Nafion 115 at 80 °C. The direct methanol fuel cell performance of the SPEES membranes was better than that of Nafion 115 membrane at 80 °C.     

Synthesis and Characterization of Sulfonated Cardo Poly(Arylene Ether Sulfone)s for Fuel Cell Proton Exchange Membrane Application

Sulfonated cardo poly(arylene ether sulfone)s ( SPPA ‐ PES ) with various degrees of sulfonation (DS) were prepared by post‐sulfonation of synthesized phenolphthalein anilide ( PPA ; N‐phenyl‐3,3′‐bis(4‐hydroxyphenyl)‐1‐isobenzopyrolidone) poly(arylene ether sulfone)s ( PPA ‐ PES ) by using concentrated sulfuric acid. PPA ‐ PES copolymers were synthesized by direct polycondensation of PPA with bis‐(4‐fluorophenyl)‐sulfone and 4,4′‐sulfonyldiphenol. The DS was varied with different mole ratios of PPA (24, 30, 40, 50 mol.%) in the polymer. The structure of the resulting SPPA ‐ PES copolymers and the different contents of the sulfonated unit were studied by Fourier transform infrared (FT‐IR) spectroscopy, ¹H NMR spectroscopy, and thermogravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymer with water. The ion exchange capacity (IEC) and proton conductivity of SPPA ‐ PES were evaluated according to the increase of DS. The water uptake (WU) of the resulting SPPA ‐ PES membranes was in the range of 20–72%, compared with 28% for Nafion 211®. The SPPA ‐ PES membranes showed proton conductivities of 23–82 mS cm^–1, compared with 194 mS cm^–1 for Nafion 211®, under 100% relative humidity (RH) at 80 °C.     

Cross‐linked Poly(arylene ether ketone) Proton Exchange Membranes with High Ion Exchange Capacity for Fuel Cells

Sulfonated poly(arylene ether ketone) (SPAEK) possessing the pendant carboxylic acid groups was synthesized. The carboxylic acid groups of SPAEK were reacted with a cross‐linking reagent to prepare a cross‐linked membrane with a high ion exchange capacity (IEC), a high oxidative stability, and an excellent mechanical strength. The cross‐linking hindered the mobility of the polymer chains and thus strongly affected the water uptake and the methanol permeability of the membranes. Also, as the cross‐linker used in this study bore sulfonic acid groups, cross‐linking did not lead to a noticeable loss of the proton conductivity. The cross‐linked SPAEK membrane with 20% cross‐linking density, CSPAEK‐20% membrane, exhibited a high proton conductivity of 0.045 S cm^–1 associated with a high IEC value of 1.78 mmol g^–1 but a low methanol permeability of 4.3 × 10^–7 cm² s^–1. The CSPAEK‐20% membrane also showed excellent cell performance and oxidation resistance.     

Sulphonated Biphenylated Poly(aryl ether ketone)s for Fuel Cell Applications

New series of fully aromatic poly(ether ketone)s with a biphenyl pendant groups were synthesised. A direct comparison of sulphonation reaction among monophenylated poly(ether ether ketone) (Ph‐PEEK), biphenylated poly(ether ether ketone) (BiPh‐PEEK) and PEEK (Victrex) was thoroughly investigated. Several advantages of the pendant‐phenyl poly(ether ketone)s compared with commercial PEEK were identified, including ready control over the site of sulphonation and degree of sulphonation (DS), and mild and rapid sulphonation. The basic membrane physical properties comprising of thermal and mechanical properties, dimensional stability and proton conductivity were studied. One new membrane, sulphonated biphenylated poly(ether ether ketone) (BiPh‐SPEEKDK) having a good combination of membrane properties was fabricated into a membrane electrode assembly (MEA), and it showed excellent direct methanol fuel cell (DMFC) performance.     

Fabrication of Function‐Graded Proton Exchange Membranes for Direct Methanol Fuel Cells Using Electron Beam‐Grafting

Function‐graded proton exchange membranes (G‐PEMs) based on poly(tetrafluoroethylene‐co‐hexafluoropropylene) were fabricated for direct methanol fuel cells (DMFCs) via electron beam‐grafting using the heterogeneous energy deposition technique. The G‐PEMs had a water uptake gradient in the proton transfer direction, originating from the sulfonic acid group gradient. The distribution of sulfonic acid groups in the various G‐PEMs was evaluated using X‐ray photoelectron spectroscopy. Four types of PEMs (flat‐type, strong‐gradient, meso‐gradient, and weak‐gradient types) were fabricated. By varying the direction of the G‐PEMs, the methanol permeation test and DMFC operation were performed with two orientations of the sulfonic acid group gradient, decreasing from the methanol injection (anode) side (decrease‐type) or the other (cathode) side (increase‐type). The methanol permeability of the strong‐gradient, meso‐gradient, and weak‐gradient G‐PEMs was lower than that of Nafion®117 and the flat‐type PEM. The “increase‐type” orientation of the strong‐gradient G‐PEM resulted in the lowest methanol permeability. The DMFC performance of the G‐PEMs was influenced by the thickness direction, such as “decrease‐type” and “increase‐type.” The performance of the “decrease‐type” assembly was higher than that of the “increase‐type.” The “decrease‐type” assembly with P‐200 k (weak‐gradient G‐PEM) exhibited the highest performance of the fabricated PEMs, comparable to that of Nafion®117.     

Sulphonated Tetramethyl Poly(ether ether ketone)/Epoxy/Sulphonated Phenol Novolac Semi‐IPN Membranes for Direct Methanol Fuel Cells

The sulphonated phenol novolac (PNBS) which was used as a curing agent of epoxy was synthesised from phenol novolac (PN) and 1, 4‐butane sultone and confirmed by FTIR and ¹H NMR. The degree of sulphonation (DS) in PNBS was calculated by ¹H NMR. The semi‐IPN membranes composed of sulphonated tetramethyl poly(ether ether ketone) (STMPEEK) (the value of ion exchange capacity is 2.01 meq g^–1), epoxy (TMBP) and PNBS were successfully prepared. The semi‐IPN membranes showed high thermal properties which were measured by differential scanning calorimeter (DSC) and thermogravimetric analyses (TGA). With the introduction of the cross‐linked TMBP/PNBS, the mechanical properties, dimensional stability, methanol resistance and oxidative stability of the membranes were improved in comparison to the pristine STMPEEK membrane. Although the proton conductivities of the semi‐IPN membranes were lower than those of the pristine STMPEEK membrane, the higher selectivity defined as the ratio of the proton conductivity to methanol permeability was obtained from the STMPEEK/TMBP/PNBS‐14 semi‐IPN membrane. The results indicated that the semi‐IPN membranes could be promising candidates for usage as proton exchange membranes in direct methanol fuel cells (DMFCs).     

Enhanced Proton Conductivity of Sulfonated Poly(ether ether ketone) Membrane Embedded by Dopamine‐Modified Nanotubes for Proton Exchange Membrane Fuel Cell

Design and fabrication of alternative proton exchange membrane (PEM) with high proton conductivity is crucial to the commercial application of PEM fuel cell. Inspired by the bioadhesion principle, dopamine‐modified halloysite nanotubes (DHNTs) bearing –NH₂ and –NH– groups are facilely synthesized by directly immersing natural halloysite nanotubes (HNTs) into dopamine aqueous solution under mild conditions. DHNTs are then embedded into sulfonated poly(ether ether ketone) (SPEEK) matrix to prepare hybrid membranes. HNTs‐filled hybrid membranes are prepared for comparison. The microstructure and physicochemical properties of the membranes are extensively investigated. Fourier transform infrared analysis implies that ordered acid–base pairs (e.g., –S–O^–…⁺H–HN–, –S–O^–…⁺H–N–) are formed at SPEEK–DHNT interface through strong electrostatic interaction. In such a way, continuous surface‐induced ion‐channels emerge along DHNTs. Although the incorporation of DHNTs reduces the channel size, water uptake, and area swelling of the hybrid membranes, which in turn would reduce the vehicle‐type proton transfer, the acid–base pairs create continuous pathways for fast proton transfer with low energy barrier via Grotthuss mechanism. Consequently, DHNT‐filled hybrid membrane with 15% DHNTs achieves a 30% increase in proton conductivity and a 52% increase in peak power density of single cell when compared with SPEEK control membrane, particularly.     

Sulphonated Poly(ether ether ketone) Proton Exchange Membranes for Fuel Cell Applications

Polymer electrolyte membrane fuel cells (PEMFCs) are promising new power sources for automotive and portable devices. Nafion® is the currently used membrane in PEMFCs. Although these membranes show high proton conductivity and excellent chemical stability, their high cost makes them unpractical for commercial purposes. Sulphonated poly(ether ether ketone) (SPEEK) ionomers were synthesized using chlorosulphonic acid as the sulphonating agent in dichloromethane medium. Homogeneous proton-conducting membranes were developed from the obtained SPEEK by solvent casting method. Membranes were assessed for their suitability in fuel cell applications. The extent of sulphonation was controlled by varying the reaction time, concentration of polymer, and concentration of sulphonating agent. The SPEEK membranes exhibit degree of sulphonation from 10 to 66%, ion exchange capacity from 0.29 to 1.92 meq/g and maximum water and methanol uptake up to 54 and 22%, respectively, at 25°C. The membranes were characterized by FTIR to confirm sulphonation, and DSC and TGA to investigate the thermal stability. The proton conductivities of such membranes were found to be excellent in the order of 10^?2 S/cm in the fully hydrated condition at room temperature as measured by impedance spectroscopy. The durability of the membranes was also tested. The study revealed the possibility of a cheaper alternative membrane for use in PEMFC.     

Fluorenyl‐containing Quaternary Ammonium Poly(arylene ether sulfone)s for Anion Exchange Membrane Applications

A series of anion exchange membranes (AEM) based on block quaternary ammonium poly(arylene ether sulfone) (QA‐bPAES) were successfully synthesized from 9,9′‐bis(4‐hydroxyphenyl) fluorene, 4,4′‐(hexafluoroisopropylidene) diphenol and 4,4′‐difluorodiphenyl sulfone via block polymerization, chloromethylation, quaternization, alkalization and solution casting. Properties of the obtained QA‐bPAES membranes, including ion exchange capacity (IEC), water uptake, swelling ratios, methanol permeability and ion conductivity were investigated. The obtained QA‐bPAES membranes showed low water uptakes, high ion conductivities and good physical and chemical stability. For example, the membrane of QA‐bPAES(20/10)‐1.34 with IEC of 1.34 mmol g⁻¹ exhibited swelling ratios of 5.0% and 5.1% in in‐plane and through‐plane direction, respectively, and ion conductivity of 15.6 mS cm⁻¹ in water at 60 °C with low methanol permeability of 1.06 × 10⁻⁷ cm² s⁻¹ (25 °C). All the results indicated that this type of block membranes had good potentials for alkaline anion exchange membrane fuel cell applications.     

耐高温新型含杂萘联苯聚醚砜嵌段共聚物的性能

将氯端基聚醚醚砜齐聚物和杂萘联苯类双酚羟端基齐聚物通过溶液缩聚,成功地合成了一系列新型聚醚醚砜-聚醚砜(PEES-PPES)嵌段共聚物,并用IR、DSC、TGA、X-WAXD等测试手段对聚合物进行了表征。结果表明:PEES-PPES具有较高的热稳定性,较好的溶剂溶解性;砜基比例的变化对PEES-PPES的热性能有较大的影响,表明砜基对杂萘联苯聚醚砜改性效果明显。     

燃料电池用的含氟质子交换膜的研发现状

质子交换膜是燃料电池中的关键部件。本文介绍了有关用于燃料电池的质子交换膜的研发现状。     

Matrix Material Study for in situ Grown Pt Nanowire Electrocatalyst Layer in Proton Exchange Membrane Fuel Cells (PEMFCs)

The cathode electrocatalyst layers were prepared by in situ growing Pt nanowires (Pt‐NWs) in two kinds of matrixes with various Pt loadings for proton exchange membrane fuel cells (PEMFCs). Commercial carbon powder and 20 wt.% Pt/C electrocatalyst were used as the matrix material for the comparison. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), polarization curves tests, and electrochemical impedance spectroscopy (EIS) were carried out to examine the effects of the matrix materials on the Pt‐NW growing and the electrode performance. The optimum Pt‐NW loadings of 0.30 mg cm⁻² in the carbon matrix (CM) and 0.20 mg cm⁻² for the Pt/C matrix (PM) were obtained. The results indicated that the Pt‐NWs grown in the CM had a better crystalline, longer size length and better catalyst activity than those in the PM. The mechanism of the matrix affection is further discussed in this paper.     

Preparation and Characterisation of Pelletised Glass Electrolytes for Fuel Cells

This paper reports on the preparation and characterisation of pelletised glass electrolytes that were fabricated with a proton conducting glass derived from a sol–gel technique, and several kinds of binders. The electrolytes, consisting of a glass powder that had been pulverised by planetary ball milling and mixed with an orthophosphoric acid binder, gave rise to a maximum proton conductivity of 1.3 × 10^–2 S cm^–1 measured at 80 °C and 80% relative humidity. The pore diameter of the PGE was in this case ∼2 nm. The hydrogen gas permeability was analysed as a function of the temperature and was found to be on the order of 10^–10 mol cm^–1 s^–1 Pa^–1 at 100 °C. Current–voltage measurements were carried out at room temperature using the PGE under H₂ and O₂ flow. Power densities were obtained from the I–V curves during fuel cell operation at 80 °C and 100% R.H.     

Surface Fluorination of Poly(fluorenyl ether ketone) Ionomers as Proton Exchange Membranes for Fuel Cell Application

A series of sulphonated poly(fluorenyl ether ketone) ionomers were successfully fluorinated by the means of direct surface fluorination. Polymer ionomer samples in two different states (membrane and powder) were treated with F₂ gas which is diluted in N₂ in a special reactor. X‐ray photoelectron spectroscopy (XPS) was used to examine the F/C ratios of the fluorinated materials. The results revealed that the fluorination only occurred on the membrane surface and the fluorination degree increased with increasing F₂ concentration in N₂. The membrane subjected to fluorination shows an obviously enhanced oxidative stability. The endurance in a Fenton's reagent of FSPFEK‐P‐28 is longer than 180 min which is two times longer than that of un‐fluorinated SPFEK. The PEM properties and single fuel cell performances were investigated by comparison of un‐ and fluorinated polymer ionomers. The fluorinated membranes demonstrated an enhanced hydrophobic surface property, increased proton conductivities and better single fuel cell performances. Surface fluorination provides a convenient and useful approach to prepare highly proton conductive membrane with long life‐time PEM fuel cell applications.     

An Algorithm for On‐line Measurement of the Internal Resistance of Proton Exchange Membrane Fuel Cell

The internal resistance of proton exchange membrane fuel cell (PEMFC) system is difficult to measure on‐line due to its variation with time. The traditional electrochemical impedance spectroscopy (EIS) and its variants such as high frequency resistance (HFR) can be used to measure the resistance when the system is in steady state, but they fail in automotive applications where a change in speed or inclination modifications could lead to a sharp fluctuation in demand on power. In order to resolve this problem, a novel algorithm is proposed in this paper to estimate the resistance based on the alternating current (AC) impedance spectroscopy technique by adding an extra term to eliminate the errors caused by voltage variation or when the system is under unsteady state. Numerical simulations show that the proposed algorithm can not only accurately track the variation of the internal resistance, but is also robust against the noises caused by uncertainty and measurements.     

Poly (ether ether ketone ketone) based imidazolium as anion exchange membranes for alkaline fuel cells

An imidazolium functionalized poly (ether ether ketone ketone) (PEEKK-DImOH) anion exchange membrane (AEM) readily soluble in certain low-boiling-point solvents (isopropanol) is prepared. The solubility results are consistent with the results of molecular dynamics simulations. By varying the chloromethylation reaction temperature or concentrated sulfuric acid concentration of PEEKK, the degrees of chloromethylation of PEEKK are changed from 54% to 92%, the corresponding PEEKK-DImOH AEMs with the ion exchange capacities (IECs) of 1.14-1.65 mmol·g^-1. The PEEKK-DImOH 92% AEM shows high hydroxide conductivity (31 mS·cm^-1), suitable water uptake (94%) and acceptable swelling ratio (39%) at 60℃. In addition, the PEEKK-DImOH AEMs possess good thermal and alkaline stability. The maximum power density (46.16 mW·cm^-2) of fuel cell prepared with PEEKK-DImOH 92% AEM as exchange membrane and ionomer is much higher than that with commercial AHA membranes. All the above results indicate that the PEEKK used in this study is a promising AEM matrix material for alkaline fuel cells.     

Gas Diffusion Layers for Proton Exchange Membrane Fuel Cells Using In situ Modified Carbon Papers with Multi‐walled Carbon Nanotubes Nanoforest

Gas diffusion layers (GDLs) in the proton exchange membrane fuel cells (PEMFCs) enable the distribution of reactant gases to the reaction zone in the catalyst layers by controlling the water in the pore channels apart from providing electrical and mechanical support to the membrane electrode assembly (MEA). In the present work, we report the in situ growth of carbon nanotubes nanoforest (CNN) directly onto macro‐porous carbon paper substrates. The surface property as analysed by a Goniometer showed that the CNN/carbon paper surface is highly hydrophobic. CNN/carbon paper was employed as a GDL in an MEA using Nafion‐212 membrane as an electrolyte and evaluated in single cell PEMFCs. While the GDLs prepared by wire‐rod coating process have major performance losses at lower humidities, the in situ CNN/carbon paper, developed in this work, shows very stable performance at all humidity conditions demonstrating a significant improvement for fuel cell performance. The CNN/carbon‐based MEAs showed very stable performance with power density values of ∼1,100 and 550 mW cm^–2, respectively, both using O₂ and air as oxidants at ambient pressure.     

邻甲基二氮杂萘联苯型聚醚酮的合成及表征

以自制的新型类双酚单体４－（３－甲基－４－羟基苯基）－２,３－二氮杂萘－１一酮,与４,４′－二氟二苯酮反应,合成了新型聚芳醚酮。初步探讨了聚合条件;用核磁共振、红外光谱分析研究了双酚单体及聚合物的结构;用ＤＳＣ、ＴＧＡ分析了聚合物的耐热性。实验结果表明,此类双酚单体具有与双酚类似的活性,可以进行聚合反应,由此合成的材料具有优异的综合性能：４００℃以下聚合物几乎没有热损失;对溶剂的溶解性能优于其它聚醚酮;力学性能良好。由于主链上引入了甲基基团,为拓宽材料的应用范围提供了一个潜在的功能基团。     

车用燃料电池质子交换膜的制备及性能

合成了一系列具有不同支化度的磺化聚芳醚砜材料,并对其结构和性能进行了表征。所制备的磺化的支化聚芳醚砜材料的分子量可达7.00×105以上,并且分子量分布在1.17左右,拉伸强度可达20.55~28.81 MPa。随着聚合物支化度的增加,聚合物的热稳定性得到改善,在550℃下的热失重可降低至39%~45%。高支化的磺化聚芳醚砜薄膜的氧化稳定性也得到改善,80℃下的使用寿命可提高至7.25 h。支化的磺化聚芳醚砜薄膜的吸水率和质子传导率都较高。80℃下高支化度的聚芳醚砜薄膜的质子传导率可达0.33 S/cm。对其微观形貌进行观测发现,支化聚芳醚砜中的支化结构可对周围的亲水磺酸基团起支撑作用,促使其发生团聚而形成连续的质子通道。