Fabrication and Microstructure Characterization of Continuous Porous TiO2/Al2O3 Composite Membrane

Using a multipass extrusion process, continuous porous Al₂O₃ body (∼41% porosity) was produced and used as a substrate to fabricate continuous porous TiO₂/Al₂O₃ composite membrane. The diameter of the continuous pores of the porous Al₂O₃ body was about 150 μm. The TiO₂ nanopowders dip coated on the continuous pore-surface Al₂O₃ body existed as rutile and anatase phases after calcination at 520°C in air. However, after aging of the fabricated continuous porous TiO₂/Al₂O₃ composite membrane in 20% NaOH at 60°C for 24 h, a large number of TiO₂ fibers frequently observed on the pore surface. The diameter of the TiO₂ fibers was about 150 nm having a high specific surface area. However, after 48-h aging period, the diameter of the TiO₂ fibers increased, which was about 3 μm. Most of the TiO₂ fibers had polycrystalline structure having nanosized rutile and anatase crystals of about 20 nm.     

Densification of Cr2O3-ZrO2 Ceramics by Sintering

Cr₂O₃ and ZrO₂ were mixed in various ratios and pressed to form compacts, which were then sintered in carbon powder. Compacts with >30 wt% Cr₂O₃ were sintered to densities >98% of true density at 1500°C. This method of sintering in carbon powder can be used to prepare very dense Cr₂O₃-ZrO₂ ceramics at a relatively low temperature, (∼1500°C) without additives.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Toughening and Strengthening of NiAl with Al2O3 by the Addition of ZrO2(3Y)

NiAl/10-mol%-ZrO₂(3Y) composites of almost full density have been fabricated via spark plasma sintering (SPS) for 10 min at 1300°C and 30 MPa. The former intermetallic compound, which contains a trace amount of Al₂O₃, has been prepared via self-propagating high-temperature synthesis. The composite microstructures are such that tetragonal ZrO₂ (∼0.2 μm) and Al₂O₃ (∼0.5 μm) particles are located at the grain boundaries of the NiAl (∼46 μm) matrix. Improved mechanical properties are obtained: the fracture toughness and bending strength are 8.8 MPa·m^1/2 and 1045 MPa, respectively, and high strength (>800 MPa) can be retained up to 800°C.     

Zirconium Aluminum Carbides: New Precursors for Synthesizing ZrO2–Al2O3 Composites

ZrO₂–Al₂O₃ nanocrystalline powders have been synthesized by oxidizing ternary Zr₂Al₃C₄ powders. The simultaneous oxidation of Al and Zr in Zr₂Al₃C₄ results in homogeneous mixture of ZrO₂ and Al₂O₃ at nanoscale. Bulk nano- and submicro-composites were prepared by hot-pressing as-oxidized powders at 1100°–1500°C. The composition and microstructure evolution during sintering was investigated by XRD, Raman spectroscopy, SEM, and TEM. The crystallite size of ZrO₂ in the composites increased from 7.5 nm for as-oxidized powders to about 0.5 μm at 1500°C, while the tetragonal polymorph gradually converted to monolithic one with increasing crystallite size. The Al₂O₃ in the composites transformed from an amorphous phase in as oxidized powders to θ phase at 1100°C and α phase at higher temperatures. The hardness of the composite increased from 2.0 GPa at 1100°C to 13.5 GPa at 1400°C due to the increase of density.     

Aluminum Titanate Formation by Solid-State Reaction of Fine Al2O3 and TiO2 Powders

The formation of Al₂TiO₅ has been studied in equimolar Al₂O₃-TiO₂ powder mixtures of ∼1μm particle sizes and moderate purity (∼99.8 wt%) at temperatures around 1300°C, where the free energy of formation is very small. Micro-structural development and reaction kinetics indicate that different mechanisms operate depending on the advancement of the reaction. The rapid initial reaction stage is interpreted as the nucleation-growth of Al₂TiO₅ cells in a virtually non-reacting matrix. The final reaction stage corresponds to the slow diffusion-controlled elimination of Al₂O₃ and TiO₂ dispersoids trapped during the growth of the initial Al₂TiO₅ cells.     

Effect of Cr3C2 Addition on the Sintering of SiC-TiC Composite

The densification behavior and mechanical properties of SiC-30TiC (in volume percent) composites prepared with Cr₃C₂ additive were investigated. By hot-pressing a SiC-30TiC-lCr₃C₂ specimen at 1950°C, 98.5% of theoretical density was achieved and the specimen exhibited a fracture strength of 750 MPa. For the SiC-30TiC-10Cr₃C₂ specimen, (β-α transformation of SiC was observed to occur during hot-pressing and in situ growth of elongated α-SiC grains resulted in an increase of fracture toughness. Micro-structural observations using high-resolution TEM indi-cated that no liquid phase was present at the interfaces.     

Crack-Healing Behavior of Al2O3 Toughened by SiC Whiskers

Al₂O₃ reinforced by SiC whiskers (Al₂O₃/SiC-W) was hot-pressed to investigate the crack-healing behavior. Semielliptical surface cracks of 100 μm in surface length were introduced using a Vickers indenter. The specimens containing precracks were crack-healed at temperatures between 1000° and 1300°C for 1 h in air, and their strengths were measured by three-point bending tests at room temperature and elevated temperatures between 400° and 1300°C. The results show that Al₂O₃/SiC-W possesses considerable crack-healing ability. The surface cracks with length of 2 c = 100 μm could be healed by crack-healing at 1200° or 1300°C for 1 h in air. Fracture toughness of the material was also determined. As expected, the SiC whiskers made their Al₂O₃ tougher.     

Grain Growth in Very Porous Al2O3 Compacts

Extensive grain growth was observed by scanning electron microscopy in very porous Al₂O₃ compacts, even at densities <40% of theoretical. After ∼7% shrinkage at 1700°C, the grain size increased from ∼0.3 to 0.51 μm in a compact having a relative green density of 0.31. During grain growth in highly porous compacts, the grains appear initially to be chainlike, then to be oblong, and finally to be equiaxed. The proposed mechanism of initial grain growth involves the filling of necks between adjacent grains followed by the movement of the grain boundary through the smaller grain. Although grain growth in very porous compacts is quite different from coalescence and ordinary grain growth, the kinetics are similar.     

Hollow Al2O3 Microspheres Derived from Al/AlOOH·nH2O Core-Shell Particles

Hollow Al₂O₃ spheres with ∼2 μm in diameter and ∼200 nm in wall thickness were prepared successfully via the calcination of the Al/AlOOH· n H₂O core-shell particles, prepared by wet-chemical method using commercial microscale aluminum powders as raw materials, at 900°–1100°C in air. X-ray powder diffraction, differential scanning calorimetric analysis, scanning electron microscopy, and transmission electron microscopy were used to characterize the obtained samples, and the possible formation mechanism was discussed. These hollow Al₂O₃ microspheres may have promising applications in insulators, lightweight fillers, and catalyst carriers because of their unique hollow structure.     

The System Al2O3-Cr2O3-Sio2

Liquidus phase equilibrium data are presented for the system Al₂O₃-Cr₂O₃-SiO₂. The liquidus diagram is dominated by a large, high-temperature, two-liquid region overlying the primary phase field of corundum solid solution. Other important features are a narrow field for mullite solid solution, a very small cristobalite field, and a ternary eutectic at 1580°C. The eutectic liquid (6Al₂O₃-ICr₂O₃-93SiO₂) coexists with a mullite solid solution (61Al₂O₃-10Cr₂O₃-29SiO₂), a corundum solid solution (19Al₂O₃-81Cr₂O₃), and cristobalite (SO₂). Diagrams are presented to show courses of fractional crystallization, courses of equilibrium crystallization, and phase relations on isothermal planes at 1800°, 1700°, and 1575°C. Tie lines were sketched to indicate the composition of coexisting mullite and corundum solid solution phases.     

Mullite Crystallization from SiO2-Al2O3 Melts

SiO₂-Al₂O₃ melts containing 42 and 60 wt% A1₂O₃ were homogenized at 2090°C (∼10°) and crystallized by various heat treatment schedules in sealed molybdenum crucibles. Mullite containing ∼78 wt% A1₂O₃ precipitated from the 60 wt% A1₂O₃ melts at ∼1325°± 20°C, which is the boundary of a previously calculated liquid miscibility gap. When the homogenized melts were heat-treated within this gap, the A1₂O₃ in the mullite decreased with a corresponding increase in the Al₂O₃ content of the glass. A similar decrease of Al₂O₃ in mullite was observed when crystallized melts were reheated at 1725°± 10°C; the lowest A1₂O₃ content (∼73.5 wt%) was in melts that were reheated for 110 h. All melts indicated that the composition of the precipitating mullite was sensitive to the heat treatment of the melts.     

Growth of Tabular α-Al2O3 Grains on Porous Alumina Substrate

Gradient, porous alumina ceramics were prepared with the characteristics of microsized tabular α-Al₂O₃ grains grown on a surface with a fine interlocking feature. The samples were formed by spin-coating diphasic aluminosilicate sol on porous alumina substrates. The sol consisted of nano-sized pseudo-boehmite (AlOOH) and hydrolyzed tetraethyl orthosilicate [Si(OC₂H₅)₄]. After drying and sintering at 1150°–1450°C, the crystallographic and chemical properties of the porous structures were investigated by analytical electron microscopy. The results show that the formation of tabular α-Al₂O₃ grains is controlled by the dissolution of fine Al₂O₃ in the diphasic material at the interface. The nucleation and growth of tabular α-Al₂O₃ grains proceeds heterogeneously at the Al₂O₃/glass interface by ripening nano-sized Al₂O₃ particles.     

Grain Growth in Two-Phase Ceramics: Al2O3 Inclusions in ZrO

The effect of Al₂O₃ inclusions with a greater average size (0.6 μm) than the average particle size of the major phase powder (<0.1 μm) on grain gowth was examined by sintering ZrO₂/Al₂O₃ composites (0,3,5,10, and 20 vol%) at 1400°C and then heat-treating at temperatures up to 1700°C. Normal grain growth was observed for all conditions. The inclusions appeared to have no effect on grain growth until the ZrO₂ grain size was ∼1.5 times the average inclusion size. Grain growth inhibition increased with volume fraction of the Al₂O₃ inclusion phase. At temperatures 1600°C, the inclusions were relatively immobile and most were located within the ZrO₂ grains for volume fractions <0.20; at higher temperatures, the inclusions could move with the grain boundary to coalesce. Grain growth was less inhilited when the inclusions could move with the boundaries, resulting in a larger increase in grain size than observed at lower temperatures. Analogies between mobile voids, entrapped within grain at lower temperature due to abnormal grain growth during the last state of sintering, and the observations concerning the mobile inclusions are made suggesting that grain-boundary movement can "sweep" voids to grain boundaries and eventually of four-grain junctions, where they are more likely to disappear by mass transport.     

Cation Tracer Diffusion in Cr2O3 and Cr2O3-0.09 wt% Y2O3

The cation diffusivities in the lattice and along dislocations and grain boundaries have been measured on sintered polycrysals of Cr₂O₃; and Cr₂Cr₂O₃-0.09 wt% Y₂O₃ at1100°C and at the pO₂ corresponding to that of Cr/Cr₂O₃ equilibrium at that temperature. Results for lattice and dislocation diffusivities in pure Cr₂O₃ are in good agreement with previous work. The present results indicate that yttrium additions have negligible effect on lattice and dislocation diffusion. However, grain-boundary diffusion in pure Cr₂O₃ is significantly slower than grain-boundary diffusion in Cr₂O₃-0.09 wt% Y₂O₃. The results are discussed in terms of their implications for the reactive-element effect in high-temperature oxidation of chromium-containing alloys.     

Formation and Transformation of TiO2 (Anatase) Solid Solution in the System TiO2—Al2O3

In the system TiO₂—Al₂O₃, TiO₂ (anatase, tetragonal) solid solutions crystallize at low temperatures (with up to ∼ 22 mol% Al₂O₃) from amorphous materials prepared by the simultaneous hydrolysis of titanium and aluminum alkoxides. The lattice parameter a is relatively constant regardless of composition, whereas parameter c decreases linearly with increasing Al₂O₃. At higher temperatures, anatase solid solutions transform into TiO₂ (rutile) with the formation of α-Al₂O₃. Powder characterization is studied. Pure anatase crystallizes at 220° to 360°C, and the anatase-to-rutile phase transformation occurs at 770° to 850°C.     

Effect of Cr2O3 on Slag Resistance of Al2O3–SiO2 Refractories

Refractory bodies of 65 wt% Al₂O₃ were prepared from a mixture of calcined alumina and raw kaolin with the addition of Cr₂O₃ up to 15 wt%. The Cr₂O₃ addition effectively enhances slag resistance and reduces mullite formation. Petrographic analysis of the refractories after the slag test suggests that Cr₂O₃ increases the viscosity of both the glassy phase in the refractory as well as the slag, thereby retarding slag penetration and reaction at elevated temperature.     

Thermodynamic Modeling of the Isomorphous Phase Diagrams in the Al2O3–Cr2O3 and V2O3–Cr2O3 Systems

The phase diagrams in the Al₂O₃–Cr₂O₃ and V₂O₃–Cr₂O₃ systems have been assessed by thermodynamic modeling with existing data from the literature. While the regular and subregular solution models were used in the Al₂O₃–Cr₂O₃ system to represent the Gibbs free energies of the liquid and solid phases, respectively, the regular solution model was applied to both phases in the V₂O₃–Cr₂O₃ system. By using the liquidus, solidus, and/or miscibility gap data, the interaction parameters of the liquid and solid phases were optimized through a multiple linear regression method. The phase diagrams calculated from these models are in good agreement with experimental data. Also, the solid miscibility gap and chemical spinodal in the V₂O₃–Cr₂O₃ system were estimated.     

Preparation and Sintering Behavior of Fine-Grained A12O3-SiO2 Composite

A fine, uniform A1₂O₃-SiO₂ powder was prepared by heterocoagulation of narrow Al₂O₃ and SiO₂ powders. This composite powder was dispersed, compacted, and fired in air at 900° to 1580°C for 1 to 13 h. Full density was achieved at 1550°C with the formation of a mullite phase. Relative densities of 83% and 98% (0.3 μm grain size) were measured for samples sintered at 1200°C for 13 h and at 1400°C for 1 h, respectively.     

Solid Solution and Chromium Oxide Loss in Part of the System MgO-Al2O3-Cr2O3-SiO2

Thermal and X-ray studies show that there is complete solid solution between MgO.Cr₂O₃ and MgO.Al₂O₃ and that the spinel solid solutions are stable with no exsolution down to temperatures as low as 510°C. There is no solid solution of excess Cr₂O₃ in MgO.Cr₂O₃ nor of MgO.Cr₂O₃ in Cr₂O₃. The join MgO.Cr₂O₃–Al₂O₃ is found to be nonbinary; compositions along that join yield mixtures of a chromium oxide-alumina solid solution and a spinel solid solution on firing to temperatures high enough to promote solid-state reaction. Chromium oxide loss by volatilization increases at higher temperature. At a given temperature, chromium oxide loss is found to vary directly with the partial pressure of oxygen in the furnace atmosphere and with the ratio of MgO to SiO₂ in the charges heated.