The System Si3N4-SiO2-Y2O3

Subsolidus phase relations were established in the system Si₃N₄-SiO₂-Y₂O₃. Four ternary compounds were confirmed, with compositions of Y₄Si₂O₇N₂, Y₂Si₃O₃N₄, YSiO₂N, and Y₁₀(SiO₄)₆N₂. The eutectic in the triangle Si₃N₄-Y₂Si₂O₇-Y₁₀(SiO₄)₆N₂ melts at 1500°C and that in the triangle Si₂N₂O-SiO₂-Y₂Si₂O₇ at 1550°C. The eutectic temperature of the Si₃N₄-Y₂Si₂O₇ join was ∼ 1520°C.     

Sintering of Si3N4-Y2O3 Under Nitrogen Pressure

This study shows that the amount ofAl₂O₃ needed to form high density Si₃N₄-15Y₂-O₃ samples can be reduced by using high surface area Si₃N₄ powder and high N₂ overpressure (high sintering temperatures) during the sintering process. The reduction in AI₂O₃ content results in improved oxidation resistance of the sintered samples.     

Phase Equilibria in the System Si3N4-SiO2-BeO-Be3N2

The 1780°C isothermal section of the reciprocal quasiternary system Si₃N₄-SiO₂-BeO-Be₃N₂ was investigated by the X-ray analysis of hot-pressed samples. The equilibrium relations shown involve previously known compounds and 8 newly found compounds: Be₆Si³N₈, Be₁₁Si₅N₁₄, Be₅Si²N₆, Be₉Si₃N₁₀, Be₈SiO₄N₄, Be₆O₃N₂, Be₈O₅N₂, and Be₉O₆N₂. Large solid solubility occurs in β-Si₃N₄, BeSiN₂, Be₉Si₃N₁₀, Be₄SiN₄, and β-Be₃N₂. Solid solubility in β-Si₃N₄ extends toward Be₂SiO₄ and decreases with increasing temperature from 19 mol% at 1770°C to 11.5 mol% Be₂SiO₄ at 1880°C. A 4-phase isotherm, liquid +β-Si₃N₄ ( ss )Si₂ON₂+ BeO, exists at 1770°C.     

Oxidation of Si3N4 Alloys: Relation to Phase Equilibria in the System Si3N4-SiO2-MgO

The oxidation resistance at 1400°C of silicon nitride alloys hot-pressed with magnesia was investigated as a function of the phase content of the alloys. The extent of oxidation, the products of oxidation, their stratification, and the continuity of the oxide scale are all dependent on the initial composition. Also, the compositions of the alloys themselves change during oxidation. The findings can be interpreted on the basis of compositional paths in the equivalence phase diagram. Reasons for the outward diffusion of Mg and impurities are given and the effect of the secondary phase on oxidation kinetics is discussed.     

High-Temperature Failure Mechanisms of Hot-Pressed Si3N4 and Si3N4/Si3N4-Whisker-Reinforced Composites

The high-temperature flexural strength of hot-pressed silicon nitride (Si₃N₄) and Si₃N₄-whisker-reinforced Si₃N₄-matrix composites has been measured at a crosshead speed of 1.27 mm/min and temperatures up to 1400°C in a nitrogen atmosphere. Load–displacement curves for whisker-reinforced composites showed nonelastic fracture behavior at 1400°C. In contrast, such behavior was not observed for monolithic Si₃N₄. Microstructures of both materials have been examined by scanning and transmission electron microscopy. The results indicate that grain-boundary sliding could be responsible for strength degradation in both monolithic Si₃N₄ and its whisker composites. The origin of the nonelastic failure behavior of Si₃N₄-whisker composite at 1400°C was not positively identified but several possibilities are discussed.     

Phase Relations and Stability Studies in the Si3N4-SiO2-Y2O3 Pseudoternary System

Composite powders were hot-pressed to determine the phase relations in the Si₃N₄-SiO₂-Y₂O₃ pseudoternary system. Four quaternary compounds, Si₃Y₂O₃N₄, YSiO₂N, Y₁₀Si₇O₂₃N₄, and Y₄Si₂O₇N₂, were identified. Studies of polyphase and single-phase materials in this system showed that these 4 compounds are unstable under oxidizing conditions. Materials within the Si₃N₄-Si₂N₂O-Y₂Si₂O₇ compatibility triangle precluded the unstable compounds, and are extremely resistant to oxidation.     

Sintering of Si3N4-Y2O3-Al2O3

Sintering kinetics of the system Si₃N4-Y2O₃-Al₂O3 were determined from measurements of the linear shrinkage of pressed disks sintered isothermally at 1500° to 1700°C. Amorphous and crystalline Si₃N₄ were studied with additions of 4 to 17 wt% Y₂O₃ and 4 wt% A1₂O₃. Sintering occurs by a liquid-phase mechanism in which the kinetics exhibit the three stages predicted by Kingery's model. However, the rates during the second stage of the process are higher for all compositions than predicted by the model. X-ray data show the presence of several transient phases which, with sufficient heating, disappear leaving mixtures of β ' -Si₃N₄ and glass or β '-Si₃N₄, α '-Si₃N₄, and glass. The compositions and amounts of the residual glassy phases are estimated.     

Kinetics of β-Si3N4 Grain Growth in Si3N4 Ceramics Sintered under High Nitrogen Pressure

The kinetics of anisotropic β-Si₃N₄ grain growth in silicon nitride ceramics were studied. Specimens were sintered at temperatures ranging from 1600° to 1900°C under 10 atm of nitrogen pressure for various lengths of time. The results demonstrate that the grain growth behavior of β-Si₃N₄ grains follows the empirical growth law Dⁿ– D₀ⁿ = kt , with the exponents equaling 3 and 5 for length [001] and width [210] directions, respectively. Activation energies for grain growth were 686 kJ/mol for length and 772 kJ/mol for width. These differences in growth rate constants and exponents for length and width directions are responsible for the anisotropy of β-Si₃N₄ growth during isothermal grain growth. The resultant aspect ratio of these elongated grains increases with sintering temperature and time.     

Crack-Tip Toughness Measurements on a Sintered Reaction-Bonded Si3N4

An evaluation of measurements of crack opening displacements (CODs) on a commercial sintered reaction-bonded silicon nitride (SRBSN) was performed. To determine the intrinsic fracture toughness of this material, a new evaluation method is presented, which takes into account not only the near tip CODs, but the CODs of the complete crack profile. The method is applied on through-thickness cracks in bend bars and contrasted to CODs of Vickers radial cracks. A crack-tip toughness of ∼1.7 MPa·m^1/2 is obtained.     

Causes and Effects of Fe-Bearing Inclusions in Sintered Si3N4

Iron is shown to increase the tendency for Si₃N₄ to decompose by formation of stable Fe-Si alloys. The decomposition reaction is temperature- and pressure-sensitive, with increasing temperatures causing greater reaction. The liquid Fe-Si alloy produced at elevated temperatures solidifies on cooling and results in metallic inclusions that act as flaws and thus mechanical failure origins.     

Phase Relations in the Si3N4-Rich Portion of the Si3N4–AlN–Al2O3–Y2O3

The phase relations in the Si₃N₄-rich portion of the Si₃N₄–AlN–Y₂O₃ rystem were investigated using hot-pressed bodies. The one-phase fields of β3 and α, the twophase fields of β+α, β+M (M=melilite), and α+M, and the three-phase fields of β+α+M were observed in the Si₃N₄-rich portion. The α- and β-sialons are not two different compounds but an allotropic transformation phase of the Si–Al–O–N system, and an α solid solution expands and stabilizes with increasing Y₂O₃ content. Therefore, the formulas of the two sialons should be the same.