Large Electrostrain in K(Nb1−xMnx)O3 Lead‐Free Piezoelectric Ceramics

K(Nb_1?xMn_x)O₃ (KN_1?xM_x) ceramics with 0.005 ≤ x ≤ 0.015 were sintered at 1020°C through a normal sintering process without the formation of a liquid phase. They exhibited double polarization versus electric field (P–E) hysteresis and sprout‐shaped strain versus electric field (S–E) curves owing to the presence of a defect dipole (P_D), which was formed between the acceptor Mn³⁺ ion and the oxygen vacancy. Moreover, the aging process was not required to develop the P_D. The KN_1?xM_x ceramics exhibited a large strain of ~0.2% at 6.0 kV/mm. For the KN_0.985M_0.015 ceramic, this large strain was maintained after 10⁴ cycles of an electric field of 6.0 kV/mm. This ceramic also maintained a double hysteresis curve at 200°C. Therefore, the KN_0.985M_0.015 ceramic has a large electric field‐induced strain, along with good thermal and fatigue properties for multilayer piezoelectric actuators.     

Excellent Transmittance Induced Phase Transition and Grain Size Modulation in Lead‐Free (1–x)(K0.5Na0.5)NbO3–xLaBiO3 Ceramics

A novel lead‐free excellent transmittance electro‐optic ceramics (1–x)(K_0.5Na_0.5)NbO₃–xLaBiO₃ (KNN‐LB, x = 0.000, 0.005, 0.010, 0.015, 0.020, 0.025, 0.040, 0.060) were fabricated by traditional pressureless ceramics processing procedure. The effects of LaBiO₃ dopant concentration x on the microstructure, phase transition, optical property, and electrical properties were studied systematically. The X‐ray diffraction results indicated that the KNN‐LB ceramics with x ≥ 0.025 have the pseudocubic phase. The morphology, density, and microstructure of the KNN‐LB ceramics were characterized by scanning electronic microscopy and optical microscopy. In particular, the KNN‐LB ceramics (0.05 mm thickness) with x = 0.025 exhibited the highest transmittance of 74.00% in the visible spectrum comparable to the 72.00% transmittance of the lead lanthanum zirconate titanate (PLZT 9/65/35 of 0.127 mm thickness). In addition, the related mechanism of transparency variation induced by phase transition and grain size modulation were discussed thoroughly. Finally, the dielectric and ferroelectric properties of as‐prepared KNN‐LB ceramics were also investigated to further clarify the relationship between transparency and relaxor behavior.     

Lead‐Free (Ba0.70Sr0.30)TiO3‐Modified Bi0.5(Na0.80K0.20)0.5TiO3 Ceramics with Large Electric Field–Induced Strains

The dielectric, ferroelectric, and electric field–induced strain behavior of Bi_0.5(Na_0.80K_0.20)_0.5TiO₃ (BNKT) ceramics modified with (Ba_0.70Sr_0.30)O₃ (BST) were investigated as a function of composition and temperature. The ceramic samples were synthesized by a solid‐state mixed oxide method and sintered at 1125°C for 2 h. The XRD and Raman spectra showed coexisting rhombohedral and tetragonal phases throughout the entire compositional range with the tetragonal phase becoming dominant at higher BST concentrations. For all compositions, the temperature dependence of the dielectric spectra revealed a frequency dependence that is characteristic of a relaxor mechanism. This suggests that these ceramics lacked long‐range order and it appears that the maximum disorder was observed for the composition with 5 mol% BST (BNKT–0.05BST sample). This was evidenced by the observation of pinched hysteresis loops, even at room temperature, and a significant decrease in the P_r and E_c values which resulted in large electric field–induced strains (S_max) of 0.40% and a normalized strain coefficient ( = S_max/E_max) of 732 pm/V. This significant strain enhancement at the composition of x = 0.05 may be attributed to both a composition‐induced structural phase transition and a field‐induced relaxor to ferroelectric phase transition.     

Enhanced Piezoelectric Properties and Thermal Stability in the (K0.5Na0.5)NbO3:ZnO Lead‐Free Piezoelectric Composites

The piezoelectric properties of (K_0.5Na_0.5)NbO₃ (KNN) are normally enhanced by chemical substitutions or doping to form solid solutions. In this study, we report that the piezoelectric properties of KNN and thermal stability of piezoelectric coefficient d₃₃ can be both enhanced by forming the composite of KNN:ZnO. The d₃₃ of KNN:0.2ZnO can be improved to 110 pC/N by introducing the ZnO nanoparticles, which is better than the pure KNN (d₃₃ = 85 pC/N). The Curie temperature (T_C = 407°C) remains well comparable to the pure KNN (T_C = 408°C). Furthermore, the thermal stability of both remanent polarization (P_r) and piezoelectric parameter (d₃₃) is improved. The enhanced thermal stability could be related to the induced built‐in electric field or the enhanced sinterability by the addition of ZnO. The present results may help to optimize the piezoelectric properties of lead‐free materials by forming composite.     

New Lead‐Free (1 − x)(K0.5Na0.5)NbO3–x(Bi0.5Na0.5)ZrO3 Ceramics with High Piezoelectricity

For enhancing the piezoelectric properties of ceramics (Bi_0.5Na_0.5)ZrO₃ (BNZ) was used to partially substitute (K_0.5Na_0.5)NbO₃ (KNN). The addition of BNZ changes the symmetry of KNN ceramics from orthorhombic to tetragonal, and finally to rhombohedral phase. A new phase boundary with both rhombohedral–orthorhombic and orthorhombic–tetragonal phase transitions near room temperature is identified for KNN–0.050BNZ ceramics, where optimum electrical properties were obtained: d₃₃ = 360 pC/N, k_p = 32.1%, ε_r = 1429, tanδ = 3.5%, and T_C = 329°C. The results indicated a new method for designing high‐performance lead‐free piezoelectric materials.     

K0.5Na0.5NbO3‐Based Lead‐Free Transparent Electro‐Optic Ceramics Prepared by Pressureless Sintering

Transparent lead‐free electro‐optic (EO) ceramics (K_0.5Na_0.5) _0.9Li_0.1Nb_0.9Bi_0.1O₃ have been fabricated by pressureless sintering. The ceramics have a fine‐grained structure and cubic‐like symmetry. The comodification with Li and Bi induces a diffuse phase transition, causing the ceramics become relaxor‐like and contain polar nanoregions. Our results reveal that excess Bi₂O₃ can further enhance the changes in the crystal structure and dielectric behavior of the ceramics, causing them become more cubic‐like and more relaxor‐like, respectively. These can reduce the light scattering arisen from birefringence and domain walls, and thus improving the optical properties. For the ceramics added with 4 and 6 mol% excess Bi₂O₃, the optical transmittance reaches a high value of 60%–70% in the near‐infrared region. The ceramics also exhibits a good linear EO response, giving an effective EO coefficient of 30–40 pm/V.     

Piezoelectric K0.5Na0.5NbO3 Ceramics Textured Using Needlelike K0.5Na0.5NbO3 Templates

Improved performance by texturing has become attractive in the field of lead‐free ferroelectrics, but the effect depends heavily on the degree of texture, type of preferred orientation, and whether the material is a rotator or extender ferroelectric. Here, we report on successful texturing of K_0.5Na_0.5NbO₃ (KNN) ceramics by alignment of needlelike KNN templates in a matrix of KNN powder using tape casting. Homotemplated grain growth of the needles was confirmed during sintering, resulting in a high degree of texture parallel to the tape casting direction (TCD) and the aligned needles. The texture significantly improved the piezoelectric response parallel to the tape cast direction, corresponding to the direction of the strongest <001>_pc orientation, while the response normal to the tape cast plane was lower than for a nontextured KNN. In situ X‐ray diffraction during electric field application revealed that non‐180° domain reorientation was enhanced by an order of magnitude in the TCD, compared to the direction normal to the tape cast plane and in the nontextured ceramic. The effect of texture in KNN is discussed with respect to possible rotator ferroelectric properties of KNN.     

Low-Temperature Sintering of (K0.5Na0.5)NbO3 Piezoelectric Ceramics

(K_0.5Na_0.5)NbO₃ piezoelectric ceramics can be sintered at a temperature as low as 750 °C for 5 h by incorporating Li₂CO₃ + Bi₂O₃ + ZnO as the sintering aid, whereas the conventional sintering temperature is around 1,100 °C. The optimal “soft” piezoelectric properties are obtained for ceramics sintered at 850 °C for 5 h. The dielectric permittivity (ε), piezoelectric coefficient (d ₃₃), electromechanical coupling (k _p) and mechanical quality factors (Q _m) of (K, Na)NbO₃ modified with 5.5 wt% sintering aids are 1,436, 90 pC/N, 0.3 and 10, respectively. These values are similar to the values obtained for (K_0.5Na_0.5)NbO₃ ceramics sintered above 1,100 °C. The underlying mechanism for abrupt change of dielectric permittivity is explained.     

The Relationship Between Phase Structure and Electrical Properties in (1 − x)(Bi0.5Na0.5TiO3–Ba0.5K0.5TiO3–BaTiO3)‐ xK0.5Na0.5NbO3 Quaternary Lead‐Free Piezoelectric Ceramics

(1 ? x)(0.85Bi_0.5Na_0.5TiO₃–0.11Ba_0.5K_0.5TiO₃–0.04BaTiO₃)‐ xK_0.5Na_0.5NbO₃ lead‐free piezoelectric ceramics with x = 0.00, 0.02, 0.03, 0.04, 0.05, and 0.10 were prepared by a conventional solid state method. A coexistence of rhombohedral (R) and tetragonal (T) phases was found in the system, which tended to evolve into pseudocubic symmetry when x increases. The x = 0.04 sample exhibited improved electrical properties: the dielectric constant ε_r = 1900 with the low loss tangents 0.06, the S_max/E_max of ~400 and ~460 pm/V under unipolar and bipolar electric field, respectively. Meanwhile, piezoelectric constant d₃₃ still maintained ~160 pC/N. These could be owed to the formation of polar nanoregions for relaxor phase.     

Large Strain Response in 0.99(Bi0.5Na0.4K0.1)TiO3–0.01(KxNa1−x)NbO3 Lead‐Free Ceramics Induced by the Change of K/Na Ratio in (KxNa1−x)NbO3

Influence of K/Na ratio in (K_xNa_1?x)NbO₃ on the ferroelectric stability and consequent changes in the electrical properties of 0.99(Bi_0.5Na_0.4K_0.1)TiO₃–0.01(K_xNa_1?x)NbO₃ (BNKT–K_xNN) ceramics were investigated. Results showed that change of K/Na ratio in KNN induces a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F?R to room temperature. Accordingly, giant strain of ~0.46% (corresponding to a large signal d₃₃* of ~575 pm/V) which is comparable to that of Pb‐based antiferroelectrics is obtained at a K/Na ratio of ~1, and the emergence of large strain response induced by the change of K/Na ratio of KNN can be well explained by the correlation between the position of ferroelectric–ergodic relaxor phase boundary in the BNKT–K_xNN system and the tolerance factor t of the end number (K_xNN). In situ high‐energy X‐ray scattering experiments with external field reveals that the large strain response in the studied system is likely related to the electric field‐induced distortion from the pseudocubic structure.     

Strong Red Emissions in Pr3+‐Doped (K0.5Na0.5)NbO3–CaTiO3 Diphase Ceramics

The photoluminescence and temperature sensing properties based on down‐shifting emission of Pr³⁺‐doped (K_0.5Na_0.5)NbO₃–yCaTiO₃ (KNN: yCT) diphasic materials were systematically investigated. Under 447‐nm excitation, Pr³⁺‐doped KNN: yCT samples exhibited significantly enhanced red emission at 603 nm assigned to ¹D₂→³H₄ transitions of Pr³⁺ ions. The red emission intensities reached the optimum value with y = 0.05 near the polymorphic phase transition region. The origin of the enhanced red emission is mainly ascribed to the doping‐induced lattice symmetry change. The energy level transitions from the typical f–f transitions to the valence‐to‐conduction transitions were observed as CaTiO₃ concentration increases above a critical concentration of y = 0.05. Furthermore, the sample with y = 0.05 also possessed excellent temperature response properties in a wide temperature range 300–473 K and the maximum sensing sensitivity was 0.016 K^?1. The Pr³⁺‐doped (K_0.5Na_0.5)NbO₃–yCaTiO₃ red emission materials with admirable intrinsic piezoelectric properties may have important technological promise in novel multifunctional devices.     

Nanodomain Engineered (K,Na)NbO3 Lead‐Free Piezoceramics: Enhanced Thermal and Cycling Reliabilities

The growing environmental concerns have been pushing the development of viable green alternatives for lead‐based piezoceramics to be one of the priorities in functional ceramic materials. A polymorphic phase transition has been utilized to enhance piezoelectric properties of lead‐free (K, Na)NbO₃‐based materials, accepting the drawbacks of high temperature and cycling instabilities. Here, we present that CaZrO₃‐modified (K, Na)NbO₃ piezoceramics not only possess excellent performance at ambient conditions benefiting from nanodomain engineering, but also exhibit superior stability against temperature fluctuation and electrical fatigue cycling. It was found that the piezoelectric coefficient d₃₃ is temperature independent under 4 kV/mm, which can be attributed to enhanced thermal stability of electric field engineered domain configuration; whereas the electric field induced strain exhibits excellent fatigue resistance up to 10⁷ sesquipolar cycles. These findings render the current material an unprecedented opportunity for actuator applications demanding improved thermal and cycling reliabilities.     

Effects of CuO Addition on Electrical Properties of 0.6BiFeO3–0.4(Bi0.5K0.5)TiO3 Lead‐Free Piezoelectric Ceramics

0.6BiFeO₃–0.4(Bi_0.5K_0.5)TiO₃ (0.6BF–0.4BKT) ceramic samples with 0.0–4.0 mol% CuO were prepared by the solid‐state reaction. The CuO addition aided the densification of the samples and slightly increased the lattice constant. The relaxor‐like defuse dielectric peak of 0.6BF–0.4BKT became sharper with increasing the CuO content. Polarization–electric field curve of the undoped 0.6BF–0.4BKT was a pinched loop in the as‐sintered state, while that was a square hysteresis with a large remanent polarization of 48 μC/cm² after the thermal quenching, demonstrating a strong domain wall pinning due to defect dipoles. We found that the CuO addition up to 2.0 mol% facilitates the polarization switching in the as‐sintered samples to increase the remanent polarization and the piezoelectric d₃₃ coefficient. The results of the structural and electrical investigations suggested that the copper ion acts as a donor in 0.6BF–0.4BKT by compensating the potassium vacancy created by the evaporation of K₂O during the calcination and sintering processes.     

Temperature‐Insensitive High Strain in Lead‐Free Bi0.5(Na0.84K0.16)0.5TiO3–0.04SrTiO3 Ceramics for Actuator Applications

Lead‐free piezoelectric ceramics, 0.96[{Bi_0.5 (Na_0.84K_0.16)_0.5}_1?xLi_x(Ti_1?yNb_y)O₃]–0.04SrTiO₃ (BNKLiTN–ST) with x, y = 0–0.030, were synthesized by solid‐state reaction method. X‐ray diffraction patterns indicated that Li and Nb successfully diffused into the BNKT–ST lattice and formed a pure perovskite structure with x, y ≤ 0.025. Increasing the Li and Nb contents (x, y = 0.020) induced a phase transformation from the coexistent rhombohedral–tetragonal phases for pure BNKT–ST ceramics to a pseudocubic phase, resulting in degradation of the remnant polarization and coercive field. However, the field‐induced strain was markedly enhanced at x, y = 0.020, giving rise to a giant dynamic piezoelectric constant (d₃₃* = S_max/E_max = 800 pm/V). Furthermore, the temperature dependence of the field‐induced strain response showed temperature‐insensitivity up to 120°C. To explore its potential for device applications, a 10‐layered stack‐type multilayer actuator was fabricated from the optimal composition (x, y = 0.020). This actuator showed a large S_max/E_max of 600 pm/V at a relatively low driving field of 4.5 kV/mm suggesting highly promising results in lead‐free BNT‐based ceramics.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Al0.5Ga0.5)O3 Lead‐Free Piezoceramics

A new lead‐free BNT‐based piezoelectric ceramics of (1 ? x)Bi_0.5Na_0.5TiO₃–xBi(Al_0.5Ga_0.5)O₃ (x = 0, 0.02, 0.03, 0.04, and 0.05) were synthesized using a conventional ceramic fabrication method. Their structures and electrical properties were investigated. All the samples show a typical ferroelectric P(E) loops and S(E) curves at room temperature. The optimal properties are obtained at the composition of the x = 0.03. The substitution of Bi(Al_0.5Ga_0.5)O₃ enhances piezoelectric constant and increases Curie temperature from 58 pC/N and 310°C of pure BNT to 93 pC/N and 325°C of the x = 0.03. The temperature‐dependent P(E) loops and S(E) curves of 0.97BNT–0.03BAG indicate that phase transition from ferroelectric to antiferroelectric takes place over a very wide temperature region from 80°C to 180°C. The results show that the introduction of BAG improves the electrical properties of BNT.     

High‐Performance (Na0.5K0.5)NbO3 Thin Film Piezoelectric Energy Harvester

The pseudocubic structure of a (Na_0.5K_0.5)NbO₃ (NKN) film grown on a Pt/Ti/SiO₂/Si substrate changed to an orthorhombic structure when the film was transferred onto a polyimide substrate. Piezoelectric constant for the transferred NKN film increased considerably from 74 ± 11 to 120 ± 18 pm/V because the crystal structure of the film had changed from pseudocubic to orthorhombic. A gold interdigitated electrode was deposited onto the transferred NKN film to synthesize a NKN piezoelectric energy harvester. The NKN piezoelectric energy harvester was poled before bending under a 100 kV/cm DC electric field across the electrodes. When a strain of 0.85% and a strain rate of 4.05%/s were applied to the NKN piezoelectric energy harvester, it produced a maximum output voltage of 1.9 V and a current of 38 nA, corresponding to a power density of 2.89 μW/cm³.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Mg0.5Ti0.5)O3 Lead‐Free Piezoceramics

Lead‐free BNT‐based piezoceramics, (1?x)Bi_0.5Na_0.5TiO₃–xBi(Mg_0.5Ti_0.5)O₃ [(1?x)BNT–xBMT] (0.00 ≤ x ≤ 0.06) binary system, were synthesized using a conventional ceramic fabrication method. Effect of Bi(Mg_0.5Ti_0.5)O₃ (BMT) substitution on room temperature (RT) crystal structure, and temperature dependence of electric properties were investigated. The XRD indicates that a pure perovskite phase is formed. The introduction of BMT decreases E_C of BNT from 7.3 to 4.0 kV/mm, and increases d₃₃ from 58 pC/N to 110 pC/N for the x = 0.05. The system shows a typical ferroelectric (FE) polarization loop P(E) and butterfly bipolar strain‐electric S(E) curve at RT. For the composition of 0.95BNT–0.05BMT antiferroelectric (AFE) phase appears near 80°C, characterized by a constricted P(E) loop and altered bipolar S(E) butterfly, and gradually prevails with increasing temperature. Temperature dependence of dielectric constant shows that T_C increases from 310°C for pure BNT to 352°C for the x = 0.05. The results indicate that the piezoelectric properties of BNT have been improved by means of Bi(Mg_0.5Ti_0.5)O₃ substitution.     

Optical and Tunable Dielectric Properties of K0.5Na0.5NbO3–SrTiO3 Ceramics

Pure perovskite K_0.5Na_0.5NbO₃–xSrTiO₃ (x = 0.16, 0.17, 0.18, and 0.19) ceramics were prepared by using a solid‐state reaction process. The ceramics were optically transparent for visible and near‐infrared wavelengths. Then, high tunability (24.1%) and low dielectric loss (0.016) for the x = 0.18 sample indicated the transparent ceramics could be used in tunable devices. The Lorentz‐type relation fitting for the temperature dependence of dielectric permittivity showed that these ceramics had a typical relaxor behavior, and the polar nanoregions were related to the tunable dielectric properties. The nonlinear dielectric behavior was further explored by the Johnson model combined with Langevin terms, which revealed that the polar nanoregions contributed to the nonlinear ε(E) dependencies with contributions of 12.3%, 11.6%, 5.9%, and 3.6% for x = 0.16, 0.17, 0.18, and 0.19, respectively.     

Seed‐Free Solid‐State Growth of Large Lead‐Free Piezoelectric Single Crystals: (Na1/2K1/2)NbO3

Large Na_0.5K_0.5NbO₃ (NKN) piezoelectric single crystals were obtained by seed‐free solid‐state crystal growth method, which is a traditional sintering grain growth process, with LiBiO₃ used as a sintering aid. The largest dimension of the single crystals obtained was 11 mm × 9 mm × 3 mm. In addition to the LiBiO₃ doping content, temperature, and time effect of the crystal growth process was systematically investigated and considered from the kinetics point of view. With the assistance of Avrami analysis, parameters relevant to the crystal growth process were determined. Laue diffraction and transmission electron microscopy suggested an orthorhombic symmetry for the single crystalline structure. Dielectric‐frequency‐temperature measurements revealed an orthorhombic‐tetragonal and tetragonal‐cubic phase transition at 155°C and 405°C, respectively, both of which are typical of first‐order transitions, and have a well‐defined thermal hysteresis. Rayleigh analysis was performed regarding to the extrinsic reversible and nonreversible piezoelectric properties, and the result suggested a dominant intrinsic reversible piezoelectric contribution of 91.5% under E₀ = 1 kV/cm AC amplitude. Such a single crystal growth process route is low cost and a relative simple preparation process.     

K0.5Na0.5NbO3-LiSbO3-BiFeO3无铅压电陶瓷的烧结特性

采用传统无压固相烧结法制备0.996(0.95K0.5NbO3-0.05LiSbO3)-0.004BiFeO3[0.996(0.95KNN-0.05LS)-0.004BF]无铅压电陶瓷,着重研究烧结保温时间对陶瓷结构、压电性能与介电性能和Curie温度Tc的影响.结果表明:随着烧结保温时间的延长,陶瓷趋于形成更稳定的四...