An experimental investigation of capillary extrudate swell in relation to parison swell behavior in blow molding

An experimental study was carried out to study and characterize the capillary extrudate swell and parison swell behavior in extrusion blow molding of two commercial blow molding grade high density polyethylene resins. The capillary extrudate swell behavior of these resins were determined employing a capillary rheometer and a special thermostatting chamber. Parison swell behavior was determined using an Impco A13-R12 reciprocating screw blow molding machine in conjunction with cinematography and pinch-off. The experimental conditions under which capillary extrudate and parison swell data can be related are elucidated. Excellent agreement is found between the area swell values determined on the basis of capillary and parison swell experiments.     

Parison formation and inflation behavior of polyamide-6 during extrusion blow molding

Parison formation and inflation behavior of three polyamide 6 resins during extrusion blow molding were investigated using cinematography, a transparent mold, a pinch-off mold and a modified blow pin, which allowed the pressure inside the parison to be determined during inflation. The glass fiber filled polyamide exhibited negligible extrudate swell and significant drawdown, whereas polyolefin modified polyamide exhibited appreciable extrudate swell and relatively small drawdown effects. The inflation behavior of the polyolefin modified polyamide was similar to the behavior of conventional blow molding grade polyolefins, whereas the unmodified and glass filled polyamides exhibited different inflation characteristics. Their inflation behavior at different internal pressures was characterized by decreasing and increasing Hencky strain rates with inflation time at high and low internal blow pressures, respectively. The characterized parison formation and inflation behavior of the polyamides emphasize the importance of rigorous blow moldability experiments and the difficulties associated with linking various rheological material functions to the blow moldability of modified polyamides.     

Measurement and calculation of parison dimensions and bottle thickness distribution during blow molding

Experimental data are reported regarding the dynamics of the blow molding process, including parison formation, growth, and inflation. These data have been obtained with the aid of high speed cinematography and pinch mold experiments, in conjunction with two commercial blow molding polyethylene resins. It is shown that pinch mold experiments alone do not yield accurate data regarding thickness and diameter swell. Furthermore, the inflation process involves decreasing rates of inflation with time, as a result of the rise in viscosity due to the cooling of the parison during inflation. Mathematical procedures are proposed for a first-order estimation of parison length and swell as a function of time and the inflation behavior after clamping. In the absence of more dependable basic procedures, the proposed treatment is employed to estimate the effective transient swell functions for the parison using experimental data obtained under the specified conditions. The mathematical treatment is extended to determine the thickness distribution of the bottle. Good agreement is obtained between experimental and calculated results.     

A comprehensive experimental study and numerical modeling of parison formation in extrusion blow molding

Parison dimensions in extrusion blow molding are affected by two phenomena, swell due to stress relaxation and sag drawdown due to gravity. It is well established that the parison swell and sag are strongly dependent on the die geometry and the operating conditions. The availability of a modeling technique ensures a more accurate prediction of the entire blow molding process, as the proper prediction of the parison formation is the input for the remaining process phases. This study considers both the simulated and the experimental effects of the die geometry, the operating conditions, and the resin properties on the parison dimensions using high density polyethylene. Parison programming with a moving mandrel and the flow rate evolution in intermittent extrusion are also considered. The parison dimensions are measured experimentally by using the pinch-off mold technique on two industrial scale machines. The finite element software BlowParison® developed at IMI is used to predict the parison formation, taking into account the swell, sag, and nonisothermal effects. The comparison between the predicted parison/part dimensions and the corresponding experimental data demonstrates the efficiency of numerical tools in the prediction of the final part thickness and weight distributions. POLYM. ENG. SCI., 47:1–13, 2007. © 2006 Society of Plastics Engineers     

Variables affecting parison diameter swell and their correlation with rheological parameters

An important factor in the selection of blow molding resins for producing handled bottles is the effective diameter swell of the parison. Ideally, the diameter swell is directly related to the weight swell and would require no separate consideration. In actual practice, the existence of gravity, the finite parison drop time and the anisotropic aspects of the blow molding operation prevent reliable prediction of the parison diameter swell directly from the weight swell. The parison diameter swell is a complex function of the weight swell, the rate of swell and the melt strength. Elements of this function are presented which show the effect of extrusion rate, parison drop time and parison weight. A technique is presented which allows the estimation of local weight and diameter swell ratios. Their direct relationship is confirmed by data obtained on several blow molding resins. The relationship between weight swell and diameter swell is definitely anisotropic. A mathematical model for swell is proposed which incorporates experimentally determined rate constants and swell coefficients. Correlations are given which suggest fundamental relationships between these derived coefficients and basic variables such as resin properties or process conditions. The model's predictive capability is demonstrated by using it to back calculate parison dimensions.     

Integrated numerical modeling of the blow molding process

The numerical modeling of the extrusion blow molding of a fuel tank is considered in this work. The integrated process phases are consecutively simulated, namely, parison formation, clamping, and inflation, as well as part solidification, part deformation (warpage), and the buildup of residual stresses. The parison formation is modeled with an integral type viscoelastic constitutive equation for the sag behavior and a semi-empirical equation for the swell behavior. A nonisothermal viscoelastic formulation is employed for the clamping and inflation simulation, since parison cooling during extrusion strongly affects the inflation behavior. Once the parison is inflated, it solidifies while in the mold and after part ejection. Warpage and residual stress development of the part are modeled with a linear viscoelastic solid model. Numerical predictions are compared with experimental results obtained on an industrial scale blow molding machine. Good agreement is observed. A process optimization based on a desired objective function, such as uniform part thickness distribution and/or minimal part weight, is performed. The integrated clamping, inflation, and cooling stages of the process are considered. The optimization is done by the systematic manipulation of the parison thickness distribution. Iterations are performed employing a gradient based updating scheme for the parison thickness programming, until the desired objective of uniform part thickness is obtained.     

Overall numerical simulation of extrusion blow molding process

This paper focuses on the overall numerical simulation of the parison formation and inflation process of extrusion blow molding. The competing effects due to swell and drawdown in the parison formation process were analyzed by a Lagrangian Eulerian (LE) finite element method (FEM) using an automatic remeshing technique. The parison extruded through an annular die was modeled as an axisymmetric unsteady nonisothermal flow with free surfaces and its viscoelastic properties were described by a K‐BKZ integral constitutive equation. An unsteady die‐swell simulation was performed to predict the time course of the extrudate parison shape under the influence of gravity and the parison controller. In addition, an unsteady large deformation analysis of the parison inflation process was also carried out using a three‐dimensional membrane FEM for viscoelastic material. The inflation sequence for the parison molded into a complex‐shaped mold cavity was analyzed. The numerical results were verified using experimental data from each of the sub‐processes. The greatest advantage of the overall simulation is that the variation in the parison dimension caused by the swell and drawdown effect can be incorporated into the inflation analysis, and consequently, the accuracy of the numerical prediction can be enhanced. The overall simulation technique provides a rational means to assist the mold design and the determination of the optimal process conditions.     

Determination of rheological parameters from parison extrusion experiments

The parison extrusion and the effects of post-extrusion swelling and sagging in the blow molding process have been studied by several authors and some qualitative relationships with rheological parameters have been attempted. The aim of this work is to show that, under some simplifying assumptions, the relevant rheological parameters—the swelling of the parison and its tensile compliance—can be directly determined from the viscoelastic analysis of the process. The reliability of the model has been tested by experiments carried out by the pinch-off mold technique which provides the parison weight profile as a function of both previous extrusion history and mold closing delay. First of all it has been shown that the proposed model is suitable to represent the data. The swelling behavior shows the expected dependence on time and shear rate and the long-time swelling data compare well with those determined by capillary extrusion experiments. It has also been found that the measured tensile compliance is of the same order of magnitude as that determined by conversion of tensile relaxation experiments; however, in the blow molding experiments the compliance of the parison decreases with increasing extrusion shear rate, i.e., by increasing the induced anisotropy of the polymer. As rheological examples, the performance displayed on both industrial and laboratory machines is discussed for three high density polyethylenes.     

Numerical simulation of blow molding—prediction of parison diameter and thickness distributions in the parison formation process

In our previous study, we calculated the time course of parison length in the parison formation stage, but it could predict only the parison area swell. The next target in our study is to calculate the parison diameter and thickness swell. Annular extrudate swell simulation is necessary for the understanding of various kinds of swelling ratios in blow molding. We have examined three kinds of swells (outer diameter, thickness, and area swells) obtained from simulation results of annular extrudate swell, using the Giesekus model, and have developed a method of predicting parison outer diameter and thickness swell values. The predicted values of parison outer diameters are discussed in comparison with experimental data, and reasonable results are obtained by the proposed method. This prediction method could also be applied to the parison formation process using a parison controller. As a result, it is possible to predict approximately the whole process of parison formation by numerical simulation.     

Fast online acquisition and analysis for parison swell and sag in blow molding

It is critical to quantitatively and reliably characterize the effects of swell and sag phenomena on the final parison dimensions in extrusion blow molding. To achieve this goal, an online image acquisition and analysis technique was developed. The successive images of parison were automatically taken using the online acquisition apparatus. These images were then analyzed by the combined use of the conventional digital image processing method and the new one developed by the authors. So the development of parison diameter and thickness swells with the extrusion time could be determined online. On the basis of the online obtained actual swell values, the pure swell and sag components were quantitatively determined. The developed technique was tested through a series of experiments using several resins under different processing parameters and die types. Shown in the present article were the results for a converging die under three different die gaps and a high‐density polyethylene. Some new phenomena were observed using the proposed technique. The results showed that the technique yields fast and accurate determination of the evolution of diameter, thickness, and length of parison during its extrusion. The technique can be employed as a part of the closed loop control for blow molded part thickness. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2399–2406, 2006     

塑料挤出吹塑的机理问题

采用不同的方法对挤出吹塑过程的型坯成型、型坯吹胀与制品冷却三阶段的机理问题进行了研究.采用人工神经网络方法预测了受模口温度和挤出流率影响的型坯成型阶段的膨胀.利用建立起来的神经网络模型预示的膨胀与实验结果很吻合,且可在一定范围内,预示不同工艺条件下型坯的直径膨胀和壁厚膨胀,为型坯的直径和壁厚的在线控制提供了理论依据.基于薄膜近似和neo-Hookean本构关系,建立了描述型坯自由吹胀的数学模型,并通过实验方法获得了型坯吹胀的瞬态图象.     

聚碳酸酯的吹塑成型

简介聚碳酸酯吹塑容器的特性与用途,着重分析其吹塑(包括挤出吹塑、共挤吹塑和注射吹塑)成型的机械(螺杆、机筒、型坯机头与吹塑模具)设计要点及工艺条件。     

A modeling approach to the effect of resin characteristics on parison formation in extrusion blow molding

The most critical stage in the extrusion blow‐molding process is the parison formation, as the dimensions of the blow‐molded part are directly related to the parison dimensions. The swelling due to stress relaxation and sagging due to gravity are strongly influenced by the resin characteristics, die geometry, and operating conditions. These factors significantly affect the parison dimensions. This could lead to a considerable amount of time and cost through trial and error experiments to get the desired parison dimensions based upon variations in the resin characteristics, die geometry, and operating conditions. The availability of a modeling technique ensures a more accurate prediction of the entire blow‐molding process, as the proper prediction of the parison formation is the input for the remaining process phases. This study considers both the simulated and the experimental effects of various high‐density polyethylene resin grades on parison dimensions. The resins were tested using three different sets of die geometries and operating conditions. The target parison length was achieved by adjusting the extrusion time for a preset die gap opening. The finite element software BlowParison® was used to predict the parison formation, taking into account the swell and sag. Good agreements were found between the predicted parison dimensions and the experimental data. POLYM. ENG. SCI., 2009. Published by Society of Plastics Engineers     

熔体挤出速度对共挤吹塑型坯离模膨胀影响的数值模拟

基于三维非等温黏弹性熔体多相分层流动有限元数值模拟技术,模拟研究了熔体挤出速度对多层共挤吹塑成型环坯离模膨胀和初始温度场的影响规律,揭示了型坯离模膨胀的产生机理。结果表明,多层共挤吹塑成型环坯离模膨胀是由熔体的二次流动诱发而产生,与熔体流出机头进入自由膨胀段的二次流动强度成正比,而其二次流动强度随着熔体挤出速度的增大而增强,因而导致环坯离模膨胀随着熔体挤出速度的增加而增大;多层共挤吹塑成型熔体的二次流动强度与其第二法向应力差成正比关联关系,这与Debbaut的试验研究结论完全吻合,表明二次流动是由第二法向应力差驱动而产生。     

支持向量机在型坯挤出壁厚预测中的应用

将支持向量机应用于挤出吹塑过程的一段型坯壁厚分布的预测,并将预测结果与人工神经网络预测的结果进行比较,验证了支持向量机具有更强的泛化能力。     

挤出吹塑型坯吹胀的CAD/CAE技术

对挤出吹塑型坯吹胀过程的CAD／CAE技术进行了初步研究。此技术可通过对吹塑CAD几何造型，CAD／CAE间信息传递，以及CAE分析的集成，实现对挤出吹塑型坯吹胀成型工艺过程的模拟和分析。最后用实例验证了此技术的可行性，为塑料制品的设计、材料选择、模具设计、吹塑成型工艺的制定及吹塑成型工艺过程的控制提供了科学依据。     

Noncontact measurement of parison thickness profiles affected by swell and sag in continuous extrusion blow molding

Optimization of final part thickness distributions is crucial in the extrusion blow molding process in order to minimize resin usage. Prediction of part thickness distributions from basic process and material parameters would be ideal. However, attempts to do so have been unsuccessful, largely because of the inability to predict parison thickness profiles. One must therefore resort to measurement of the parison thickness profile and estimation of the final part thickness distribution by computational methods. This paper describes a new technique for the noncontact estimation of parison thickness profiles in continuous extrusion blow molding. The method accounts for sag and requires no previous knowledge of rheological data. It can be employed on-line for the purposes of process monitoring and control. The approach is based on the measurement of the parison length evolution with time during extrusion, the parison diameter profile, the flow rate, and the melt temperature gradient along the length of the parison. These parameters are utilized in conjunction with a theoretical approach that describes the extrusion of a parison under the effects of swell, sag, and extrusion into ambient conditions. Results are presented for three resins of various molecular weight distributions. The degree of sag is minimal at the top and bottom of the parison, and reaches a maximum near the center of the parison. Results are also presented to demonstrate the versatility of the method under other process conditions, such as varying flow rate, die temperature, and die gap.     

Numerical simulation of blow molding—Viscoelastic flow analysis of parison formation

The simulation of the parison formation process in blow molding has been studied. The flow field was divided into two regions, namely, the extrudate swell region near the die lip and the parison formation region after the exit swell. In the swell region, we predicted the swelling ratio and residual stress distribution for high Weissenberg numbers for steady planar well using the 1-mode Giesekus model. In the parison formation region, the flow is assumed to be an unsteady unaxial elongational flow including drawdown and recoverable swell and is modeled using the 10-mode Giesekus model. We calculated the time course of parison length and thickness distribution, and compare the calculation results of parison length with experimental data. It was found that the predicted values agreed rather well with the experimental values. The calculation results could especially predict the shrink-back, which is the phenomenon where the parison length becomes shorter after the cessation of extrusion, and it was found tat this was caused by the recoverable swell of the parison, which depends on the tensile stress generation in the die. Various flow rates and die geometries were studied and confirmed the reliability and usefulness of the method.     

Effect of acrylic processing aids on PVC die swell

The die swell behavior of PVC melts is a manifestation of melt elasticity and is of considerable commercial as well as fundamental importance. This behavior is a critical issue in extrusion blow molding application where die swell (i.e. parison thickness) needs to be controlled. Advantageously, the addition of high molecular weight acrylic processing aids to PVC provides better die swell control, thus, improving dramatically the processability of PVC. Hence, knowledge of molecular weight variables of such acrylic processing aids is important from both the commercial and rheological point of view. Various acrylic processing aids were prepared by polymerization designed to provide systematic variation of molecular parameters. Molecular weight distribution of the polymers was characterized by GPC, and their die swell behavior in a typical PVC blow molding formulation was determined at 200°C over various range of residence times using different L/D capillary dies. The results are presented showing effects of specific molecular variables.     

Numerical simulation of suction blow molding process for producing curved ducts

During suction blow molding process, the extruded parison undergoes twisting deformation within the mold cavity, as the air drawing flow around the deforming parison exerts non‐uniform shear stresses on its surface. Such twisting deformation can compromise the specific radial and circumferential variations in parison thickness that are intentionally generated during extrusion. This research is devoted in developing a fluid–structure interaction model for predicting parison deformation during suction blow molding process, with a specific emphasis on the suction stage. A fluid flow model, based on Hele‐Shaw approximations, is formulated to simulate the air drag force exerted on the parison surface. The rheology of the material of the parison is assumed to obey the viscoelastic K‐BKZ model. As the suction process also involves the sliding of the parison within the mold cavity, a modified Coulomb's law of dry friction is used to simulate the frictional contact between parison and mold. The numerical results of this study allowed identifying a clear correlation between the twisting deformation undergone by the parison during the suction stage, also observed experimentally and the design parameters, namely, the air drawing speed, the geometry of the duct mold cavity, and the parison/mold eccentricity. POLYM. ENG. SCI., 59:418–434, 2019. © 2018 Her Majesty the Queen in Right of Canada