共查询到20条相似文献,搜索用时 93 毫秒
1.
比较了不同密封型式蝶阀的密封原理,提出了金属密封蝶阀对电动装置的性能要求,介绍了不同结构型式电动装置影响金属密封蝶阀密封性能的因素。 相似文献
2.
3.
介绍了高温三偏心硬密封蝶阀的密封结构及结构弊端,指出了影响当前蝶阀密封结构不能承受反向压力的原因,在此基础上对蝶阀密封结构进行了改进设计.改进后的密封结构保证了正、反向的可靠密封性,解决了以往反向不能密封的问题,经试验验证改进后的蝶阀反向承压密封性能良好. 相似文献
4.
5.
6.
主要论述了楔紧式金属密封蝶阀的结构和工作原理。重点介绍了楔紧式金属密封蝶阀的设计计算,并对高温条件下的设计提出了要求和方法。 相似文献
7.
8.
针对液氢用低温三偏心蝶阀较难现实反向密封的问题,对三偏心蝶阀在实现反向密封过程中出现的泄漏问题进行分析,探讨了三偏心蝶阀密封的影响因素,研究了三偏心蝶阀反向密封时蝶板的变形。结果表明:在流体反向流动时,解决蝶阀密封副的密封比压,是解决液氢用低温蝶阀反向密封的关键;三偏心蝶阀密封副的密封比压与其过盈配合设计相关;三偏心蝶阀密封圈的密封面边线是形成接触密封的关键位置,将过渡区的面密封改为线密封,有利于降低三偏心蝶阀在关闭时密封圈对阀座的磨损程度,为确保蝶阀形成有效的反向密封,蝶阀关闭时须在密封面上形成连续的密封比压;通过对蝶板和阀座结构采取加大密封部件的刚度和提高密封副的结合程度等优化设计措施,可实现三偏心蝶阀的反向承压密封的功能。选取Class150 NPS42三偏心蝶阀,使用氦气测试其在液氮(-196℃)环境下的反向密封性能,通过试验验证,低温蝶阀在设计压差内的泄漏量不能超过4 L/min,满足并优于标准允许的泄漏值,研究结果可为液氢用低温三偏心蝶阀的设计提供参考依据。 相似文献
9.
10.
针对液氢用低温三偏心蝶阀较难现实反向密封的问题,对三偏心蝶阀在实现反向密封过程中出现的泄漏问题进行分析,探讨了三偏心蝶阀密封的影响因素,研究了三偏心蝶阀反向密封时蝶板的变形。结果表明:在流体反向流动时,解决蝶阀密封副的密封比压,是解决液氢用低温蝶阀反向密封的关键;三偏心蝶阀密封副的密封比压与其过盈配合设计相关;三偏心蝶阀密封圈的密封面边线是形成接触密封的关键位置,将过渡区的面密封改为线密封,有利于降低三偏心蝶阀在关闭时密封圈对阀座的磨损程度,为确保蝶阀形成有效的反向密封,蝶阀关闭时须在密封面上形成连续的密封比压;通过对蝶板和阀座结构采取加大密封部件的刚度和提高密封副的结合程度等优化设计措施,可实现三偏心蝶阀的反向承压密封的功能。选取Class150 NPS42三偏心蝶阀,使用氦气测试其在液氮(-196℃)环境下的反向密封性能,通过试验验证,低温蝶阀在设计压差内的泄漏量不能超过4 L/min,满足并优于标准允许的泄漏值,研究结果可为液氢用低温三偏心蝶阀的设计提供参考依据。 相似文献
11.
12.
针对金属硬密封蝶阀的双向密封问题,基于液压元件设计中的油缸活塞原理,设计了一种在动水作用下带移动密封不锈钢圈的新型金属硬密封蝶阀。对基本结构进行了分析,确定了采用双偏心结构的设计;对正向承压比压、反向承压比压、金属密封圈的移动距离进行了计算,有效地解决了双偏心金属硬密封蝶阀的反向承压问题;对密封副材料选择进行了分析,有效地保证了密封效果和比压要求。 相似文献
13.
14.
Investigation of the mechanical behavior of a flexible solid metal seal for a cryogenic butterfly valve 总被引:1,自引:0,他引:1
Ahn Jun Tae Lee Kyung Chul Lee Kwon Hee Han Seung Ho 《Journal of Mechanical Science and Technology》2011,25(9):2393-2400
Seat tightness at the fully shut position should be a consideration in the development of a butterfly valve for use in a liquefied
natural gas (LNG) vessel. A flexible solid metal seal offers sufficient tightness of the butterfly valve and meets the specifications
for cryogenic temperature. In the present study, characteristics for a cryogenic butterfly valve, such as the flow coefficient
and the pressure loss coefficient, were estimated by numerical fluid analysis carried out to simulate 3-D flow and to study
performance as it was affected by the opening angles of the valve disc. A design criterion to ensure the seat tightness of
the butterfly valve at the fully shut position was proposed, in which the contact pressure between the metal seal and the
valve disc would be compared with the fluid pressure. Numerical structural analysis showed that the contact pressure can be
calculated by simulation of the frictional contact behavior on the surface of the metal seal and the valve disc. As a result,
an adequate flexibility of the metal seal and the valve disc was required in order to accomplish a contact pressure that would
be high enough to satisfy the seat tightness requirement. Under cryogenic temperature, thermal shrinkage caused the metal
seal to adhere closely to the valve disc periphery at both sides and raised the contact pressure to a relatively high value,
though there was no contact across a small area at the center position, which is susceptible to leakage. An additional displacement
of the metal seal and the valve disc appeared at an operating fluid pressure of 6.9 bar and produced sufficient contact pressure
at the no-contact area. This was verified by experimental leakage tests performed at room and cryogenic temperatures. 相似文献
15.
介绍了水轮机进水蝶阀双密封的用途,分析了检修密封副和工作密封副的结构特点,探讨了该类型阀门在实际工程应用中存在的问题,论述了国外同类产品性能。 相似文献
16.
17.
18.
介绍了一种结合Solidworks二维作图软件,在避免干涉情况下,快速确定三偏心蝶阀回转中心位置的方法。用该方法同时可求得最小径向偏心量,控制了三偏心蝶阀的启闭力矩而且提高了反向密封性能。在优化的同时大大简化了三偏心蝶阀的设计。 相似文献
19.
运用AutoCAD对金属硬密封蝶阀密封挤压过程产生的干涉体进行定性和定量分析.为修正、验证和确定蝶阀的三偏心参数提供设计依据。分析了双偏心球面密封副的优良性能。 相似文献