Effect of Al on the microstructure and mechanical properties of Mg–6Zn–2Sn–0.5Mn alloy

The microstructure and mechanical properties of Mg–6Zn–2Sn–0.5Mn–xAl (x?=?0, 1, 2, 3) alloy are investigated. The addition of Al leads to the refinement of grain size and the formation of Al₆Mn, Mg₃₂(Al,Zn)₄₉ also forms when the amount of Al is higher than 2?wt-%. Because of the addition of Al, the precipitates in the alloy after ageing treatment are refined. The alloy containing 1?wt-% Al shows good mechanical properties in the as-cast state which is attributed to the refined grains and low volume fraction of large second phases, it also shows high strength after ageing treatment resulted mainly from the homogeneously distributed fine precipitates, the yield strength, ultimate tensile strength and elongation are 183, 310?MPa and 11%, respectively.     

Effect of cooling aging on microstructure and mechanical properties of an Al–Zn–Mg–Cu alloy

In the present work, Al–Zn–Mg–Cu alloy was aged by non-isothermal cooling aging treatment (CAT). At high initial aging temperature (IAT), the hardness was decreased with the decreased cooling rate. However, when IAT was lower than 180 °C, the hardness was increased with the decreased cooling rate. Conductivity was increased with the decreased cooling rate regardless of IAT. The tensile strength, yield strength and conductivity of Al alloy after (200–100 °C, 80 °C/h) CAT were increased 2.9%, 8.1% and 8.3% than that after T6 treatment, respectively. With an increase of IAT and decrease of cooling rate, the fine GP zone and η′ phase were transformed to be larger η′ and η precipitates. Moreover, continuous η phase at grain boundary was also grown to be individual large precipitates. Cooling aging time was decreased about 90% than that for T6 treatment, indicating cooling aging could improve the mechanical properties, corrosion resistance and production efficiency with less energy consumption.     

Effects of yttrium and heat treatment on the microstructure and tensile properties of Al–7.5Si–0.5Mg alloy

The effects of yttrium (Y) additions (0, 0.1, and 0.3 wt.%) and T6 heat treatment on the microstructure and tensile properties of Al–7.5Si–0.5Mg alloy have been investigated in the present work. The microstructures and fracture surfaces of as-cast and heat treated samples were examined by scanning electron microscopy (SEM). It was found that Y modified the eutectic silicon from a coarse plate-like and acicular structure to a fine branched and some fibrous one with a better uniform distribution. In addition, T6 heat treatment played a crucial role in the fragmentation and spheroidization of eutectic silicon, especially in the well modified alloys. The tensile properties were improved by the addition of Y followed by the T6 heat treatment, and a good combination of ultimate tensile strength (353 MPa), yield strength (287 MPa) and elongation (12.1%) was obtained when the Y addition was 0.3 wt.%. Furthermore, fractographic examinations revealed that dimple-like mechanism was responsible for ductile fracture.     

Effects of samarium content on microstructure and mechanical properties of Mg–0.5Zn–0.5Zr alloy

Effects of samarium (Sm) content (0, 2.0, 3.5, 5.0, 6.5 wt%) on microstructure and mechanical properties of Mg–0.5Zn–0.5 Zr alloy under as-cast and as-extruded states were thoroughly investigated. Results indicate that grains of the as-cast alloys are gradually refined as Sm content increases. The dominant intermetallic phase changes from Mg₃Sm to Mg₄₁Sm₅ till Sm content exceeds 5.0 wt%. The dynamically precipitated intermetallic phase during hot-extrusion in all Sm-containing alloys is Mg₃Sm. The intermetallic particles induced by Sm addition could act as heterogeneous nucleation sites for dynamic recrystallization during hot extrusion. They promoted dynamic recrystallization via the particle stimulated nucleation mechanism, and resulted in weakening the basal texture in the as-extruded alloys. Sm addition can significantly enhance the strength of the as-extruded Mg–0.5Zn–0.5 Zr alloy at room temperature, with the optimal dosage of 3.5 wt%. The optimal yield strength (YS) and ultimate tensile strength (UTS) are 368 MPa and 383 MPa, which were enhanced by approximately 23.1% and 20.8% compared with the Sm-free alloy, respectively. Based on microstructural analysis, the dominant strengthening mechanisms are revealed to be grain boundary strengthening and dispersion strengthening.     

Effect of equivalent strain and redundant shear strain on microstructure and texture evolution during hot rolling in Mg–3Al–1Zn alloys

Equivalent strain and redundant shear strain distribution in the roll bite during normal rolling were calculated by a numerical integration method combined with the experimental method. The microstructural parameters, such as length of high-angle grain boundaries (HAGB), length of low-angle grain boundaries (LAGB) per unit area, and (0002) basal texture in surface layer and center layer were measured quantitatively by EBSD or X-ray diffraction. The effect of equivalent strain and redundant shear strain on the microstructure and (0002) basal texture evolution in AZ31 alloy during hot rolling were examined. As a result, it was found that the formation of the HAGB depends on the equivalent strain, while the formation of the LAGB is strongly affected by the redundant shear strain, which restrains the formation of the LAGB. The experimental results also suggest that the redundant shear may have little effect on improving DRX and weakening the (0002) basal texture intensity when the redundant shear strain is in small to moderate range (≤0.8).     

Effect of Sr on microstructure,tensile properties and wear behavior of as-cast Mg–6Zn–4Si alloy

The microstructure, tensile properties and wear behavior of as-cast Mg–6Zn–4Si alloy with strontium additions at ambient and elevated temperature were investigated by means of X-ray diffraction (XRD), optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), standard high temperature tensile testing and a pin-on-disc type apparatus. The results indicated that the grain size of the primary Mg₂Si decreased initially and then gradually increased with increasing Sr amount. Meanwhile, the morphology of the primary Mg₂Si in the alloys changed from large dendritic to polygonal or fine block, and that of the eutectic Mg₂Si phase turned to fine fibre with increasing Sr content. Tensile testing results showed that Sr addition improved the ultimate tensile and elongation of the Mg–6Zn–4Si alloys at both ambient temperature and 150 °C. Dry sliding wear tests indicated that the change trend of wear rate was basically coincident with that about the average size of the primary Mg₂Si phases. Optimal mechanical properties and wear behavior could be achieved by a Sr addition of 0.5%. An excessive Sr addition resulted in the formation of the needle-like SrMgSi compound, which was detrimental to the tensile properties and wear behavior of the alloys.     

High speed rolling of Mg–3Al–1Zn alloy: texture and microstructure analysis

Abstract

High speed rolling (HSR) of 1000 m min^?1 was employed to successfully roll AZ31 alloy in one pass with 65% reduction in thickness at 300 and 450°C. The rollability, texture and microstructure after HSR, in comparison with low speed rolling (15 m min^?1), improved significantly. It is suggested that the double peak and weaker basal texture obtained after HSR are attributed to the activation of compression and double twins. After annealing, the double peak basal texture is replaced by a single peak one, which may be due to preferential grain growth of basal grains.     

Influence of Sc and Zr additions on microstructure and properties evolution of Al–Zn–Mg alloy

Journal of Materials Science - In this study, the effects of different Sc?+?Zr compound addition on the tensile properties, impact toughness, stress corrosion cracking (SCC) properties,...     

Microstructure and tensile properties of squeeze cast Al–Zn–Mg–Cu alloy

Abstract

It is well known that wrought aluminium alloys have tensile properties superior to those of the cast products. Wrought grade alloys cannot usually be produced by conventional casting processes to attain the same level of tensile properties. However, progress in casting methods in recent years has made it possible to produce wrought alloys by means of squeeze casting techniques. In the present study an Al–Zn–Mg–Cu alloy has been produced by squeeze casting. Tensile properties close to those of wrought products have been achieved by controlling the microstructure, pressure, and other processing parameters.     

Effects of processing parameters on microstructure and mechanical properties of squeeze-cast Mg–12Zn–4Al–0.5Ca alloy

In this paper, a new magnesium alloy Mg–12Zn–4Al–0.5Ca (ZAX12405) was prepared by squeeze casting. The effects of processing parameters including applied pressure, pouring temperature and dwell time on the microstructure and mechanical properties of squeeze-cast ZAX12405 alloy were investigated. It was found that squeeze-cast ZAX12405 alloy exhibited finer microstructure and much better mechanical properties than gravity casting alloy. Increasing the applied pressure led to significant cast densification and a certain extent of grain refinement in the microstructure, along with obvious promotion in mechanical properties. Lowering the pouring temperature refined the microstructure of ZAX12405 alloy, but deteriorated the cast densification, resulting in that the mechanical properties firstly increased and then decreased. Increasing the dwell time promoted cast densification and mechanical properties just before the solidification process ended. A combination of highest applied pressure (120 MPa), medium pouring temperature (650 °C) and dwell time (30 s) brought the highest mechanical properties, under which the ultimate tensile strength (UTS), yield strength (YS) and elongation to failure (E_f) of the alloy reached 211 MPa, 113 MPa and 5.2% at room temperature. Comparing with the gravity casting ZAX12405 alloy, the UTS and E_f increased 40% and 300%, respectively. For squeeze-cast Mg–12Zn–4Al–0.5Ca alloy, cast densification was considered more important than microstructure refinement for the promotion of mechanical properties.     

Effects of Cu content on microstructure and mechanical properties of Al–14.5Si–0.5Mg alloy

This study elucidates how Cu content affects the microstructure and mechanical properties of Al–14.5Si–0.5Mg alloy, by adding 4.65 wt.% and 0.52 wt.% Cu. Different Fe-bearing phases were found in the two alloys. The acicular β-Al₅FeSi was found only in the high-Cu alloy. In the low-Cu alloy, Al₈Mg₃FeSi₆ was the Fe-bearing phase. Tensile testing indicated that the low-Cu alloy containing Al₈Mg₃FeSi₆ had higher UTS and elongation than the high-Cu alloy containing the acicular β-Al₅FeSi. It is believed that the presence of the acicular β-Al₅FeSi in the high-Cu alloy increased the number of crack initiators and brittleness of the alloy. Increasing Cu content in the Al–14.5Si–0.5Mg alloy also promoted solution hardening and precipitation hardening under as-quenched and aging conditions, respectively. The hardness of the high-Cu alloy therefore exceeded that of low-Cu alloy.     

Effect of predeformation on microstructure and mechanical properties of Al–Cu–Li–Zr alloy containing Sc

Abstract

The effects of prior cold deformation on the microstructures and the room temperature mechanical properties of an Al–3·5Cu–1·5Li–0·22(Sc + Zr) alloy have been observed by using TEM and tensile test at room temperature. The results show that the alloy has the character of aging hardening, and the major phase of precipitation and strengthening is T₁ phase. The result also show that prior cold deformation leads to more dispersive and uniform distribution of T₁ precipitations. It accelerates aging response, causes earlier aging peak occurrence, and enhances strength greatly. However, the plasticity of the alloy is declined with prior cold deformation. In contrast, excessive prior cold deformation causes coarsening and heterogeneous distribution of T₁ phase. It also reduces the strength of the alloy, therefore, influences the composite properties of the alloy. The favourable prior cold deformation is about 3·5% under the experimental condition.     

Influence of retrogression and reaging on microstructure and properties of 8090 Al–Li alloy

Abstract

An investigation was made into the influence of a retrogression and reaging treatment on the microstructure, tensile properties, and stress corrosion cracking resistance of 8090 Al–Li alloy. The results show that retrogression of the material at 230°C for 40 min or 325°C for 1·5 min, and then reaging to the peak aged condition, can result in an improved combination of tensile strength and stress corrosion cracking resistance. Through retrogression and reaging treatment, the alloy almost achieves the strength of the peak aged state and the stress corrosion cracking resistance of the overaged state. Transmission electron microscopy indicates that the δ′ phase dissolves during retrogression and reprecipitates during reaging, thus increasing the strength. The T₂ phase precipitates and grows during both retrogression and reaging, which results in the increase of stress corrosion cracking resistance.

MST/1670     

Effect of processing variables on structure and tensile properties of investment cast Al–Si–Mg casting alloy

Abstract

A research programme was conducted to study the effects of grain refinement, eutectic silicon modification, filtering, pouring and shell preheat temperatures, and heat treatment on the structure and tensile properties of an investment cast Al–Si–Mg alloy, LM25 (BS 1490 : 1988). The principal findings of the research were that: an increase in shell preheat temperature adversely affects the structure and, hence, the tensile properties; grain refinement was enhanced as the titanium content was increased to about 0·28% but the tensile properties were not affected; a modified eutectic silicon structure was achieved with strontium additions in the range 0·01–0·02%, with the optimum addition, based on tensile properties, being 0·01%; and, as would be expected, heat treatment improved the tensile properties. On the basis of the interrelationships between process variables, structural changes, and tensile properties observed, an optimum processing route was identified. The optimum tensile properties were obtained in fully heat treated specimens that had been both grain refined and modified and produced in moulds poured at ambient temperature.     

Influence of equal channel angular extrusion processing parameters on the microstructure and mechanical properties of Mg–Al–Y–Zn alloy

An as-cast Mg–Al–Y–Zn alloy was successfully processed by equal channel angular extrusion (ECAE) in the temperature range of 225–400 °C, and the influences of processing temperature on the microstructure and mechanical properties were investigated. The use of back pressure during one-pass ECAE of Mg–Al–Y–Zn alloy was favorable for eliminating the undeformed area in the billet. At the processing temperature below 250 °C, the microstructures were characterized by unrecrystallised structure and the precipitated phase Mg₁₇Al₁₂ was elongated along the extrusion direction. With increasing processing temperature to 350 °C, a large number of recrystallised grains were obtained. Increasing processing temperature promoted workability but led to decrease in the strength of Mg–Al–Y–Zn alloy. Then billets of as-cast Mg–Al–Y–Zn alloy were extruded at different numbers of ECAE passes. It was found that the microstructure was effectively refined by ECAE and mechanical properties were improved with numbers of ECAE passes increasing from one-pass to four passes. However, strengths decreased slightly after five passes though the grain size decreased considerably.     

Influence of the combined addition of Y and Nd on the microstructure and mechanical properties of Mg–Li alloy

Y and Nd are simultaneously added into Mg–5Li–3Al–2Zn alloy. It is found that there exist the phases of α-Mg, AlLi, Al₁₁Nd₃ and Al₂Y in the alloys. When the contents of Y and Nd are 1.2% and 0.8%, respectively, the grain is the finest with an average size of 30 μm, and the tensile strength of the alloy reaches 231 MPa, the elongation reaches 16%. When the ratio of Y to Nd is 1.2:0.8, there is a synergistic strengthening effect.     

Effect of strain on cavity development during Al–Zn–Mg–Cu alloy superplastic flow

Cavitation behaviour has been investigated in an Al–Zn–Mg–Cu alloy with an average grain size of 10?µm during superplastic deformation. The superplastic tensile tests were interrupted at different true strains at 530°C and 3?×?10^?4?s^?1. The results showed that cavity nucleation occurred above a critical strain in the optimum loading condition. It was easy for cavities to form at the triple junction due to the stress concentration caused by cooperative grain boundary sliding. Since the tensile stress was higher in the middle of the sample, the cavities were arranged in a straight line parallel to the tensile axis in the centre of the sample. A more appropriate cavity growth equation considering the critical strain was proposed to describe the cavitation behaviour.     

Effect of local volume fraction of microporosity on tensile properties in Al–Si–Mg cast alloy

Abstract

Porosity in Al–Si–Mg cast alloys utilised in automotive parts affects directly products quality, i.e. mechanical properties. In this study, the effect of micropores on mechanical properties has been investigated by X-ray tomography from the viewpoint of clustering micropores. The local volume fraction (LVF) of porosity was introduced to analyse the effect of clustering micropores. The statistical Weibull method was also used in order to explain strength of the alloy tested. The fracture strain decreased drastically from 17 to 3% on an inverse parabolic relationship with increasing porosity. In the case of the specimens that contain the largest pore higher than 100 m m, the ultimate tensile strength decreases monotonically. It is found that the fracture surface passes through high LVF regions. The fracture strain obviously depends on the ratio of LVF higher than 10%. It is confirmed that the LVF, which represents unevenly distribution of micropores cluster, is one of important dominant factor for managing the mechanical properties in the Al–Si–Mg cast alloy.     

Effect of upset forging on microstructure and tensile properties in a devitrified Al–Ni–Co–Y Alloy

Devitrified Al—transition metal—rare earth alloys offer routes to obtain higher volume fractions of dispersed strengthening phases than conventional precipitation routes. Here, we report a study of the microstructure–property relationships of an Al–Ni–Co–Y alloy processed by gas atomization and consolidated/devitrified by warm extrusion. Microstructural characterization by electron microscopy and serial section FIB tomography show that the alloy comprises an FCC Al matrix and 44 % by volume of elongated Al₁₉(Ni,Co)₅Y₃ plates with the Al₁₉Ni₅Gd₃ structure. The plates are aligned with the extrusion direction in the as-extruded alloy, and tensile data show a distinct anisotropy in yield strength and strain to failure. These data are consistent with the alloy acting more like a unidirectional short-fiber-reinforced metal–matrix composite than a conventional precipitation-hardened alloy. During axial upset forging, the ternary plates do not break up, but instead they rotate, until at large upset strains they lie perpendicular to their original orientation with corresponding changes in the tensile properties. The materials exhibit yield strengths of up to 713 MPa and tensile elongations of up to 5 %. Thus, such systems could form the basis for truly deformable high-strength low-density metal–matrix composites.     

Influence of yttrium addition on the corrosion behaviour of as-cast Mg–8Li–3Al–2Zn alloy

The influence of yttrium on the microstructure and corrosion behaviour of as-cast Mg–8Li–3Al–2Zn–xY alloys was investigated. The results show that Y addition leads to the formation of Al₂Y particles and the transformation of α-Mg from the long needle-like to the round-like. The noble Al₂Y particles on the grain boundary inhibit the galvanic corrosion between β-Li phase and α-Mg phase, and also weaken the corrosion occurrence inside β-Li phase due to the decrease of the AlLi phase. With Y addition, the corrosion resistance is improved gradually, especially when the content of Y is up to 1.5 wt-%. Moreover, Y addition makes the corrosion film become more compact, which can prevent the base materials from being attacked continuously.