Preparation of novel pyridine‐based,thermally stable poly(ether imide)s

Two aromatic, pyridine‐based ether diamines were prepared by the nucleophilic aromatic substitution reaction of 4‐aminophenol and 5‐amino‐1‐naphthol with 2,6‐dichloropyridine in N‐methyl‐2‐pyrrolidone as a solvent. Polycondensation reactions of the obtained diamines with pyromellitic dianhydride, benzophenone tetracarboxylic dianhydride, and hexafluoroisopropylidene diphthalic anhydride resulted in six pyridine‐based, thermally stable poly(ether imide)s. The prepared monomers and polymers were characterized by common spectroscopic methods. The physical and thermal properties of the polymers, including the thermal behavior, thermal stability, solubility, and solution viscosity, were studied. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 22–26, 2004     

Thermally stable and organosoluble cardo binaphthylene based poly(amide imide)s and poly(ester imide)s

A new imide‐containing dicarboxylic acid based on a twisted binaphthylene unit, 2,2′‐bis(N‐trimellitoyl)‐1,1′‐binaphthyl (1), was synthesized from 1,1′‐binaphthyl‐2,2′‐diamine and trimellitic anhydride in glacial acetic acid. The structure of compound 1 was fully characterized with spectroscopic methods and elemental analysis. Series of thermally stable and organosoluble poly(amide imide)s (4a–4d) and poly(ester imide)s (5a–5d) with similar backbones were prepared by the triphenyl phosphite and diphenylchlorophosphate activated direct polycondensation of diimide dicarboxylic acid 1 with various aromatic diamines and diols, respectively. With due attention to the structural similarity of the resulting poly(amide imide)s and poly(ester imide)s, most of the differences between these two block copolyimides could be easily attributed to the presence of alternate amide or ester linkages accompanied by imide groups in the polymer backbone. The ultraviolet maximum wavelength values of the yellowish polymers were determined from their ultraviolet spectra. The crystallinity of these copolyimides was estimated by means of wide‐angle X‐ray diffraction, and the resultant polymers exhibited a nearly amorphous nature, except for the polymers derived from benzidine and 4,4′‐binaphthol. The poly(amide imide)s exhibited excellent solubility in a variety of highly polar aprotic solvents, whereas the poly(ester imide)s showed good solubility in less polar solvents. According to differential scanning calorimetry analyses, polymers 4a–4d and 5a–5d had glass‐transition temperatures between 331 and 357°C and between 318 and 342°C, respectively. The thermal behaviors of the obtained polymers were characterized by thermogravimetric analysis, and the 10% weight loss temperatures of the poly(amide imide)s and poly(ester imide)s were between 579 and 604°C and between 566 and 577°C in nitrogen, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3203–3211, 2006     

Synthesis and properties of fluorinated aromatic poly(amide imide)s based on 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone and various bis(trimellitimide)s

A CF₃‐containing diamine, 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone ( 2 ), was synthesized from 4,4′‐dihydroxybenzophenone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( 3 and 5B_a – 5B_g ) were prepared by the condensation reaction of aromatic diamines and trimellitic anhydride. Then, two series of novel soluble aromatic poly(amide imide)s (PAIs; 6A_a – 6A_k and 6B_a – 6B_g ) were synthesized from a diamine ( 4A_a – 4A_k or 2 ) with the imide‐containing diacids ( 3 and 5B_a – 5B_g ) via direct polycondensation with triphenyl phosphate and pyridine. The aromatic PAIs had inherent viscosities of 0.74–1.76 dL/g. All of the synthesized polymers showed excellent solubility in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and afforded transparent and tough films by DMAc solvent casting. These polymer films had tensile strengths of 90–113 MPa, elongations at break of 8–15%, and initial moduli of 2.0–2.9 GPa. The glass‐transition temperatures of the aromatic PAIs were in the range 242–279°C. They had 10% weight losses at temperatures above 500°C and showed excellent thermal stabilities. The 6B series exhibited less coloring and showed lower yellowness index values than the corresponding 6A series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3641–3653, 2006     

Synthesis and characterization of novel soluble pyridine‐containing polyimides based on 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine and various aromatic dianhydrides

A new kind of pyridine‐containing aromatic diamine monomer, 4‐phenyl‐2,6‐bis[4‐(4‐aminophenoxy)phenyl]‐pyridine (PAPP), was successfully synthesized by a modified chichibabin reaction of benzaldehyde and a substituted acetophenone, 4‐(4‐nitrophenoxy)‐acetophenone (NPAP), followed by a reduction of the resulting dinitro compound 4‐phenyl‐2,6‐bis[4‐(4‐nitrophenoxy)phenyl]‐pyridine (PNPP) with Pd/C and hydrazine monohydrate. The aromatic diamine was employed to synthesize a series of new pyridine‐containing polyimides by polycondensation with various aromatic dianhydrides in N‐methy‐2‐pyrrolidone (NMP) via the conventional two‐step method, i.e., ring‐opening polycondensation forming the poly (amic acid)s and further thermal or chemical imidization forming polyimides. The inherent viscosities of the resulting polyimides were in the range of 0.79–1.13 dL/g, and most of them were soluble in common organic solvents such as N,N‐dimethylacetamide (DMAc), NMP, and tetrahydrofuran (THF), etc. Meanwhile, strong and flexible polyimide films were obtained, which had good thermal stability, with the glass transition temperatures (T_g) of 268–338°C and the temperature at 5% weight loss of 521–548°C in air atmosphere, as well as outstanding mechanical properties with tensile strengths of 89.2–112.1 MPa and elongations at break of 9.5–15.4%. The polyimides also were found to possess low dielectric constants ranging from 2.53 to 3.11. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 212–219, 2007     

Synthesis and characterization of polyamides and poly(amide‐imide)s derived from 2,6‐bis(3‐aminophenoxy)benzonitrile or 2,6‐bis(4‐aminophenoxy)benzonitrile

A series of polyamides and poly(amide‐imide)s was prepared by direct polycondensation of ether and nitrile group containing aromatic diamines with aromatic dicarboxylic acids and bis(carboxyphthalimide)s respectively in N‐methyl 2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. New diamines, such as 2,6‐bis(4‐aminophenoxy)benzonitrile and 2,6‐bis(3‐aminophenoxy)benzonitrile, were prepared from 2,6‐dichlorobenzonitrile with 4‐aminophenol and 3‐aminophenol, respectively, in NMP using potassium carbonate. Bis(carboxyphthalimide)s were prepared from the reaction of trimellitic anhydride with various aromatic diamines in N,N′‐dimethyl formamide. The inherent viscosities of the resulting polymers were in the range of 0.27 to 0.93 dl g^?1 in NMP and the glass transition temperatures were between 175 and 298 °C. All polymers were soluble in dipolar aprotic solvents such as dimethylsulfoxide, dimethylacetamide and NMP. All polymers were stable up to 350 °C with a char yield of above 40 % at 900 °C in nitrogen atmosphere. All polymers were found to be amorphous except the polyamide derived from isophthalic acid and the poly(amide‐imide)s derived from diaminodiphenylether and diaminobenzophenone based bis(carboxyphthalimide)s. Copyright © 2004 Society of Chemical Industry     

Novel trifluoromethyl‐containing poly(amide–imide)s: Organosolubility,optical behavior,thermostability, and crystallinity

A new dicarboxylic acid monomer, 2,6‐bis(1,3‐dioxo‐5‐carboxyisoindolin‐2‐yl)‐4,4′‐bis(trifluoromethyl)‐1,1′‐diphenyl ether (IFDPE), bearing two preformed imide rings was synthesized via a three‐step manner from 4‐(trifluoromethyl)phenol and 4‐chloro‐3,5‐dinitrobenzotrifluoride. The monomer IFDPE was then used to prepare a series of novel trifluoromethyl‐containing poly(amide–imide)s via a direct phosphorylation polycondensation with various aromatic diamines. The intrinsic viscosities of the polymers were found to be in the range 0.86–1.02 d/g. The weight‐ and number‐average molecular weights of the resulting polymers were determined with gel permeation chromatography. The polymeric samples were readily soluble in a variety of organic solvents and formed low‐color, flexible thin films via solution casting. The values of the absorption edge wavelength were determined by ultraviolet–visible spectroscopy, and all of the resulting poly (amide–imide)s films exhibited high optical transparency. The resulting polymers showed moderately high glass‐transition temperatures in the range 295–324°C and had 10% weight loss temperatures in excess of 524°C in nitrogen. The crystallinity extents were qualitatively investigated with wide‐angle X‐ray diffraction measurements. Scanning electron microscopy images revealed an agglomerated bulk with nonuniformity on the surface. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Microwave‐assisted synthesis of high‐molecular‐weight poly(ether imide)s by phase‐transfer catalysis

A facile and rapid polycondensation reaction of disodium bisphenol A with bis(chlorophthalimide)s was preformed with a domestic microwave oven in o‐dichlorobenzene by phase‐transfer catalysis. The polymerization reactions, in comparison with conventional heating polycondensation, proceeded rapidly and were completed within 25 min. The polymerizations gave the corresponding poly(ether imide)s with inherent viscosities of 0.55–0.92 dL g^?1. The effects of various factors on the polymerization, such as the amount of the catalyst, the reaction time, and the microwave power were studied. The properties of the polymers were briefly characterized. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2415–2419, 2004     

Fabrication and characterization of soluble,high thermal,and hydrophobic polyimides based on 4‐(3,5‐dimethoxyphenyl)‐2,6‐bis(4‐aminophenyl)pyridine

A novel aromatic diamine monomer, 4‐(3,5‐dimethoxyphenyl)‐2,6‐bis(4‐aminophenyl)pyridine (DPAP) was successfully synthesized by 4′‐nitroacetophenone and 3,5‐dimethoxybenzaldehyde as raw material. The structure of DPAP was confirmed by Fourier transform infrared, nuclear magnetic resonance, and mass analysis. A series of polyimides (PIs) were obtained by polycondensation with various dianhydrides via the conventional two‐step method. These PIs showed good solubility in organic solvents. They also presented high thermal stability, the glass transition temperatures (T_g) of polymers were in the range of 325–388 °C, and the temperature at 10% weight loss was in the range of 531–572 °C. Furthermore, these polymers also exhibited outstanding hydrophobicity with the contact angles in the range of 89.1°–93.5°. Moreover, the results of wide‐angle X‐ray diffraction (WAXD) confirmed these polymers showed amorphous structure. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45827.     

Synthesis and characterization of new aromatic poly(amide–imide)s based on 4‐aryl‐2,6‐bis(4‐trimellitimidophenyl) pyridines

New diimide–dicarboxylic acids, ie 4‐phenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine and 4‐p‐biphenyl‐2,6‐bis‐(4‐trimellitimidophenyl)pyridine, were synthesized by the condensation reaction of 4‐phenyl‐2,6‐bis(4‐aminophenyl)pyridine and 4‐p‐biphenyl‐2,6‐bis(4‐aminophenyl)pyridine with trimellitic anhydride in glacial acetic acid or dimethylformamide. The monomers were fully characterized by FT‐IR and NMR spectroscopies, and elemental analyses. A series of novel poly(amide–imide)s with inherent viscosities of 0.68–0.87 dl g^?1 was prepared from the two diimide–diacids with various aromatic diamines by direct polycondensation. The poly(amide–imide)s were characterized by FT‐IR and NMR spectroscopies. The λ_max data for the resulting poly(amide–imide)s were in the range of 260–292 nm. These polymers exhibited good solubilities in polar aprotic solvents. The 10 % weight loss temperatures are above 485 °C under a nitrogen atmosphere. Copyright © 2004 Society of Chemical Industry     

Preparation and properties of new thermally stable poly(ether imide amide)s

2,6‐Bis(4‐aminophenoxy)pyridine was prepared via reaction of 4‐aminophenol with 2,6‐dichloropyridine in the presence of potassium carbonate. Reaction of the diamine with two mol of trimellitic anhydride afforded a diacid with preformed imide structures. Poly(ether imide amide)s were prepared by polycondensation reactions of the diacid with different diamines in the presence of triphenyl phosphite. All the monomers and polymers were fully characterized and the physical properties of the polymers including solution viscosity, thermal stability, thermal behavior and solubility were studied. Thermal analysis data showed the polymers to have high thermal stability. Copyright © 2004 Society of Chemical Industry     

Step‐growth polymerization of 5‐[(9,10‐dihydro‐9,10‐ethanoanthracene‐11,12‐dicarboximido)‐3‐methylbutanoyl‐amino]isophthalic acid with aromatic diols

cis‐9,10‐dihydro‐9,10‐ethanoanthracene‐11,12‐dicarboxylic acid anhydride ( 1 ) was converted to imide acid ( 2 ) by reaction with S‐valine. Compound 2 was converted to the acid chloride ( 3 ) by reaction with thionyl chloride and then treated with 5‐aminoisophthalic acid in dry N,N‐dimethylacetamide to obtain 5‐[(9,10‐dihydro‐9,10‐ethanoanthracene‐11,12‐dicarboximido)‐3‐methylbutanoylamino]isophthalic acid ( 4 ). Direct step‐growth polymerization of this novel chiral diacid monomer 4 with a series of different diols in a system of tosyl chloride, pyridine, and N,N‐dimethylformamide was carried out. The optically active polyesters (PEs) were obtained with good yield and moderate inherent viscosity ranging from 0.23 to 0.48 dL/g. The resulting polymers were characterized with FTIR, ¹H‐NMR, and elemental analysis techniques. The prepared PEs showed good thermal stability up to 320°C as measured by thermogravimetric analysis. Specific rotation experiments demonstrated the induction of optical activity due to successful insertion of S‐valine in the structure of pendant groups. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Novel diols containing ester and amide groups and resulting poly(ester amide ester)s

The reaction of terephthaloyl chloride and 4‐hydroxybenzoic acid resulted in terephthalyl bis(4‐oxybenzoic) acid. This diester diacid was converted into its corresponding diester diacid chloride (terephthaloyl dioxydibenzoylchloride) via a reaction with thionyl chloride. Diols with preformed ester and amide groups were prepared through the reaction of terephthaloyl dioxydibenzoylchloride with 4‐aminophenol and 5‐amino‐1‐naphthol. Polycondensation reactions of the prepared diols with different aromatic and aliphatic diacid chlorides afforded eight aromatic and semiaromatic poly(ester amide ester)s. The polymers were fully characterized, and their physical and thermal properties were studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2699–2703, 2004     

Synthesis and characterization of new cardo poly(ether imide)s derived from 9,9‐bis [4‐(4‐aminophenoxy)phenyl]xanthene

A series of new cardo poly(ether imide)s bearing flexible ether and bulky xanthene pendant groups was prepared from 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene with six commercially available aromatic tetracarboxylic dianhydrides in N,N‐dimethylacetamide (DMAc) via the poly(amic acid) precursors and subsequent thermal or chemical imidization. The intermediate poly(amic acid)s had inherent viscosities between 0.83 and 1.28 dL/g, could be cast from DMAc solutions and thermally converted into transparent, flexible, and tough poly(ether imide) films which were further characterized by X‐ray and mechanical analysis. All of the poly(ether imide)s were amorphous and their films exhibited tensile strengths of 89–108 MPa, elongations at break of 7–9%, and initial moduli of 2.12–2.65 GPa. Three poly(ether imide)s derived from 4,4′‐oxydiphthalic anhydride, 4,4′‐sulfonyldiphthalic anhydride, and 2,2‐bis(3,4‐dicarboxyphenyl))hexafluoropropane anhydride, respectively, exhibited excellent solubility in various solvents such as DMAc, N,N‐dimethylformamide, N‐methyl‐2‐pyrrolidinone, pyridine, and even in tetrahydrofuran at room temperature. The resulting poly(ether imide)s with glass transition temperatures between 286 and 335°C had initial decomposition temperatures above 500°C, 10% weight loss temperatures ranging from 551 to 575°C in nitrogen and 547 to 570°C in air, and char yields of 53–64% at 800°C in nitrogen. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Chopping high‐molecular weight poly(1,4‐butylene carbonate‐co‐aromatic ester)s for macropolyol synthesis

The condensation of a mixture of dimethyl carbonate and phthalate derivatives with 1,4‐butanediol (BD), catalyzed by sodium alkoxide, generated high‐molecular weight poly(1,4‐butylene carbonate‐co‐aromatic ester)s with molecular weights (M_n) of 50–120 kDa. The subsequent addition of polyols [BD, glycerol propoxylate, 1,1,1‐tris(hydroxymethyl)ethane, or pentaerythritol] chopped these high‐molecular weight polymers to afford macrodiols or macropolyols with facile control of their molecular weights (M_n, 2000–3000 Da) and unique chain topological compositions. Macropolyols prepared by chopping poly(1,4‐butylene carbonate‐co‐terephthalate) were waxy in nature, whereas those containing isophthalate and phthalate units were oily. The macropolyols synthesized by this chopping method may have potential applications in the polyurethane industry. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43754.     

Syntheses and properties of new poly(amide–imide)s based on 1,4‐bis(4‐aminophenoxy)naphthalene and various diimide–diacids

A series of new alternative poly(amide–imide)s (PAIs, III_a–j ) was synthesized by the direct polycondensation of 1,4‐bis(4‐aminophenoxy)naphthalene (1,4‐BAPON) with various aromatic diimide–diacids. These polymers were obtained in quantitative yields with inherent viscosities of 0.71–1.03 dL/g. Except for III_a, most of the polymers were soluble in aprotic polar solvents such as NMP, DMAc, DMF, and DMSO and could be solution‐cast into transparent, flexible, and tough films. The glass transition temperatures of these PAIs were in the range of 235–280°C. Thermogravimetric analyses established that these polymers were fairly stable up to 450°C, and 10% weight loss temperatures were recorded in the range of 520–569°C under nitrogen and 506–566°C under an air atmosphere. Compared with the PAIs with the 1,4‐bis(4‐aminophenoxy)benzene structure (series IV), the solubility of series III was better than that of series IV. Series III also exhibited lower crystallinity and better processability than those of series IV. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 217–225, 2000     

γ‐Butyrolactone‐processable high‐modulus poly(ester imide)s

γ‐Butyrolactone (GBL)‐processable high modulus heat‐resistant materials were developed in this work. The polyaddition of an ester‐containing tetracarboxylic dianhydride, i.e. hydroquinone bis(trimellitate anhydride) (TAHQ), and 2,2′‐bis(trifluoromethyl)benzidine (TFMB) in GBL resulted in gelation in the initial reaction stage. The incorporation of a methyl group to TAHQ (M‐TAHQ) allowed polymerization with TFMB in GBL and led to a homogeneous poly(ester imide) (PEsI) precursor solution with a short pot life of 3 days, whereas a simple copolymerization approach using bulky/flexible comonomers to TAHQ/TFMB was less effective. PEsI precursors (PEsAAs) were prepared from TFMB, M‐TAHQ and a minor fraction of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA) or a fluorene‐containing tetracarboxylic dianhydride. These PEsAA systems showed drastically improved GBL solution stability. In particular, the M‐TAHQ(80);6FDA(20)/TFMB copolymer system provided a PEsAA film with a very high light transmittance at 365 nm (>70%). A photosensitive film composed of this matrix resin and diazonaphthoquinone provided a clear positive‐tone pattern by development in a 2.38 wt% tetramethylammonium hydroxide aqueous solution at room temperature with a high dissolution contrast. The thermally cured PEsI film achieved a very high tensile modulus (>5 GPa) as the present target with other desirable properties, i.e. sufficient film flexibility, a relatively low coefficient of thermal expansion, a high T_g and low water absorption. The present materials can be promising candidates as novel buffer coat films in semiconductor applications. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

Phosphorus‐containing thermoplastic poly(ether ester) elastomers showing intrinsic flame retardancy

A series of poly(ether ester) thermoplastic elastomers (TPEEs) are synthesized by a one‐pot, two‐step method: (1) transesterification of dimethyl‐2,6‐naphthalenedicarboxylate with 1,4‐butanediol (BDO) as chain extender (CE), followed by (2) low‐pressure melt polycondensation with poly(tetramethylene ether glycol) as a soft segment in the presence of Ti(OBu)₄ as a catalyst. In order to design phosphorous‐containing flame‐retardant TPEEs, hydroxyl‐terminated isobutylbis(hydroxypropyl)phosphine oxide (IHPO) is integrated into the polymer backbone as the second CE, modulating the IHPO content up to 30% with respect to BDO. The resultant TPEEs are systematically characterized using various spectral, thermal, and mechanical analyses. An increase in phosphorus content in the polymer backbone enhances the flame retardancy of TPEE, adapting them as promising halogen‐free self‐extinguishing thermoplastic elastomers without losing their elastomeric properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45478.     

Synthesis of soluble and thermally stable polyimides from 3,5‐diamino‐N‐(4‐(8‐quinolinoxy) phenyl) aniline and various dianhydrides

Three novel polyimides (PIs) having pendent 4‐(quinolin‐8‐yloxy) aniline group were prepared by polycondensation of a new diamine with commercially available tetracarboxylic dianhydrides, such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs were characterized by FTIR, ¹H NMR, and elemental analysis; they had high yields with inherent viscosities in the range of 0.4–0.5 dl g⁻¹, and exhibited excellent solubility in many organic solvents such as N,N‐dimethyl acetamide, N,N′‐dimethyl formamide, N‐methyl pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. These PIs exhibited glass transition temperatures (T_g) between 250 and 325° C. Their initial decomposition temperatures (T_i) ranged between 270 and 450°C, and 10% weight loss temperature (T₁₀) up to 500°C with 68% char yield at 600°C under nitrogen atmosphere. Transparent and hard polymer films were obtained via casting from their NMP solutions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Catalyzed chain extension of poly(butylene adipate) and poly(butylene succinate) with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline)

Low‐molecular‐weight HOOC‐terminated poly(butylene adipate) prepolymer (PrePBA) and poly(butylene succinate) prepolymer (PrePBS) were synthesized through melt‐condensation polymerization from adipic acid or succinic acid with butanediol. The catalyzed chain extension of these prepolymers was carried out at 180–220°C with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) as a chain extender and p‐toluenesulfonic acid (p‐TSA) as a catalyst. Higher molecular weight polyesters were obtained from the catalyzed chain extension than from the noncatalyzed one. However, an improperly high amount of p‐TSA and a high temperature caused branching or a crosslinking reaction. Under optimal conditions, chain‐extended poly(butylene adipate) (PBA) with a number‐average molecular weight up to 29,600 and poly(butylene succinate) (PBS) with an intrinsic viscosity of 0.82 dL/g were synthesized. The chain‐extended polyesters were characterized by IR spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray scattering, and tensile testing. DSC, wide‐angle X‐ray scattering, and thermogravimetric analysis characterization showed that the chain‐extended PBA and PBS had lower melting temperatures and crystallinities and slower crystallization rates and were less thermally stable than PrePBA and PrePBS. This deterioration of their properties was not harmful enough to impair their thermal processing properties and should not prevent them from being used as biodegradable thermoplastics. The tensile strength of the chain‐extended PBS was about 31.05 MPa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010