Synthesis and characterization of polybutadiene with monotitanocene/methylaluminoxane catalyst

Butadiene was polymerized using a monotitanocene complex of η⁵‐pentamethylcyclopentadienyltribenzyloxy titanium [Cp*Ti(OBz)₃] in the presence of four types of modified methylaluminoxanes (mMAO), which contained different amounts of residual trimethylaluminum (TMA). The titanium oxidation states in Cp*Ti(OBz)₃/mMAO and Cp*Ti(OBz)₃/mMAO/triisobutylaluminum (TIBA) catalytic systems were determined by redox titration method. The effects of various oxidation states of titanium active species on butadiene polymerization were investigated. It was found that Ti(III) active species is more effective for preparing polybutadiene with high molecular weight. The addition of TIBA to the Cp*Ti(OBz)₃/mMAO system could reduce a greater number of Ti(IV) complexes to Ti(III) species and lead to significant increases of polymerization activity and molecular weight of polymer, whereas the polybutadiene microstructure was only slightly changed. On the basis of microstructure and property characterization by FTIR, ¹³C‐NMR, DSC, and WAXD, all resultant polymers were proved to be amorphous polybutadiene with mixed 1,2; cis‐1,4; and trans‐1,4 structures. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2494–2500, 2004     

The synthesis of high molecular weight polybutene‐1 catalyzed by Cp★ Ti(OBz)3/MAO

A new stereoregular polybutene‐1 was synthesized with a novel catalyst precursor η⁵‐pentamethyl cyclopentadienyl titanium tribenzyloxide (CpTi(OBz)₃) and methylaluminoxane (MAO). The effects of polymerization conditions on the catalytic activity, molecular weight and stereoregularity of the products were investigated in detail. It was found the catalyst exhibited highest activity of 91.2 kgPB mol Ti⁻¹ h⁻¹ at T = 30 °C, Al/Ti = 200. The catalytic activity and molecular weight were sensitive to the Al/Ti (mole/mole), polymerization temperature; they also depended on the Ti concentration. The molecular weight of the products increased with decreasing temperature. The structure and properties of the polybutene‐1 were characterized by ¹³C NMR, GPC, DSC and WAXD. The result showed the microstructure of polybutene‐1 extracted by boiling heptane was stereoregular, whereas the ether‐soluble fraction was atactic. The molecular weight of polybutene‐1 was over one million g mol⁻¹ and its molecular weight distribution ( M _w/ M _n) was from 1.1 to 1.2. © 2001 Society of Chemical Industry     

Synthesis and characterization of novel reactive ladder‐like polysilsesquioxanes with side‐chain ester groups (Ester‐Ts)

Two kinds of structure‐ordered reactive ladder‐like polysilsesquioxanes with different side‐chain ester groups (Ester‐Ts) have been synthesized successfully by a new route – stepwise coupling polymerization – with three steps including preaminolysis, hydrolysis and polycondensation. Two monomers, 2‐trichlorosilylethyl acetate (M₁) and 3‐trichlorosilylpropyl propionate (M₂), were first synthesized by hydrosilylation with dicyclopentadienylplatinum (II) chloride (Cp₂PtCl₂) as a catalyst. Monomer and polymer structures were characterized by FTIR, ¹H NMR, ¹³C NMR, ²⁹Si NMR, X‐ray diffraction (XRD), differential scanning calorimetry (DSC) and vapour pressure osmometry (VPO). Characterization data indicate that these two polymers have ordered ladder‐like structures. © 2000 Society of Chemical Industry     

A new post‐metallocene catalyst for alkene polymerization: copolymerization of ethylene and 1‐hexene with titanium complexes bearing N,N‐dialkylcarbamato ligands

A new type of post‐metallocene polymerization catalyst based on titanium complexes with N,N‐dialkylcarbamato ligands was used to copolymerize ethylene and 1‐hexene. These easy‐to‐synthesize and stable complexes in combination with different organoaluminium co‐catalysts produce random ethylene/1‐hexene copolymers characterized by a broad molecular weight distribution and high 1‐hexene incorporation, as confirmed by SEC, DSC and ¹³C NMR analysis. The influence of the main reaction parameters on the polymerization reactions was studied including the type of catalyst components, solvent, temperature, the ethylene partial pressure and the [Al]/[Ti] ratio in the catalyst. A higher activity and a higher 1‐hexene incorporation were achieved with AlMe₃‐depleted methylalumoxane as co‐catalyst and chlorobenzene as solvent. © 2013 Society of Chemical Industry     

Solvent Effect on Complexation of Titanium Tetraethoxide with Allylacetoacetate

The effect of the solvent butanol on the complexation reaction of allylacetoacetate (AAA) with titanium tetraethoxide. (Ti(OEt)₄) in molar ratio Ti(OEt)₄:AAA = 1:1 was investigated by ¹³C-NMR, FT-IR spectroscopy and elemental analysis. The investigation shows that some ethoxy groups that are attached to the titanium are substituted with butoxy groups. The hydrolytic stability of the allylacetoacetate–Ti complex in a molar ratio Ti(OEt)₄:H₂O = 1:4 was also characterized by spectroscopic techniques and elemental analysis. The result of this characterization shows that almost 20% of the AAA and some ethoxy groups are released from the hydrolyzed product.     

Complexation of Zirconium Alkoxides with 3-Pentenoic Acid and Hydrolytic Stability of Their Products

Reactions of Zr(OPr ⁿ )₄ and Zr(OBu ⁿ )₄ with 3-pentenoic acid (PA) in 1:1 molar ratio were studied in propanol and butanol solution at room temperature by the sol–gel process. The complexations were investigated by ¹³C{¹H}, ¹H-NMR and FTIR spectroscopy. The ¹³C{¹H}, ¹H-NMR and FTIR spectra showed that PA completely reacted with Zr(OPr ⁿ )₄ and Zr(OBu ⁿ )₄. The new products were hydrolyzed by water in a ratio of 1:4 (Zr(OR ⁿ )₄/ H₂O, R = propyl, butyl). The stability of hydrolyzed products was investigated spectroscopically. After hydrolysis, it was observed that no PA was released from the complexes, [Zr(OPr ⁿ )₃(PA)] and [Zr(OBu ⁿ )₃(PA)], under the reaction conditions.     

Synthesis and biological activity of medium range molecular weight polymers containing exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid

A new monomer, exo‐3,6‐epoxy‐1,2,3,6‐tetrahydrophthalimidocaproic acid (ETCA), was prepared by reaction of maleimidocaproic acid and furan. The homopolymer of ETCA and its copolymers with acrylic acid (AA) or with vinyl acetate (VAc) were obtained by photopolymerizations using 2,2‐dimethoxy‐2‐phenylacetophenone as an initiator at 25 °C. The synthesized ETCA and its polymers were identified by FTIR, ¹H NMR and ¹³C NMR spectroscopies. The apparent average molecular weights and polydispersity indices determined by gel permeation chromatography (GPC) were as follows: M_n = 9600 g mol^?1, M_w = 9800 g mol^?1, M_w/M_n = 1.1 for poly(ETCA); M_n = 14 300 g mol^?1, M_w = 16 200 g mol^?1, M_w/M_n = 1.2 for poly(ETCA‐co‐AA); M_n = 17 900 g mol^?1, M_w = 18 300 g mol^?1, M_w/M_n = 1.1 for poly(ETCA‐co‐VAc). The in vitro cytotoxicity of the synthesized compounds against mouse mammary carcinoma and human histiocytic lymphoma cancer cell lines decreased in the following order: 5‐fluorouracil (5‐FU) ≥ ETCA > polymers. The in vivo antitumour activity of the polymers against Balb/C mice bearing sarcoma 180 tumour cells was greater than that of 5‐FU at all doses tested. © 2001 Society of Chemical Industry     

Synthesis of thermoreactive polysiloxanes with cyclic fragments in the side chain

The synthesis of polysiloxanes with pendant unsaturated cyclic fragments have been successfully performed by hydrosilylation reactions of polymethylhydrosiloxane with 4‐vinyl‐1‐cyclohexene in the presence of platinum hydrochloric acid (0.1 M solution in THF), Karstedt's catalyst (Pt₂[(VinSiMe₂)₂O]₃) and platinum on the charcoal (5%). Reactions were carried out at various temperatures with different ratios of initial compounds. It was shown, that not all active ≡Si? H groups take part in the hydrosilylation reaction. Some kinetic parameters of reactions were studied. The synthesized oligomers were characterized by FTIR, ¹H, ¹³C, H,H‐COSY, and C,H‐correlation NMR spectroscopy. Calculations using the quantum‐chemical semi empirical AM1 method for modeling reactions between methyldimethoxysilane [Me(MeO)₂SiH] and 4‐vinyl‐1‐cyclohexene were performed to evaluate possible reaction paths. Synthesized oligomers were characterized by gel‐permeation chromatography, differential scanning calorimetric, thermogravimetric, and wide‐angle X‐ray analyses. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel phenyl acetylene terminated poly(carborane‐silane): Synthesis,characterization, and thermal property

Phenyl acetylene terminated poly(carborane‐silanec) (PACS) was synthesized by the couple reaction of methyldichlorosilane with 1,7‐dilithio‐m‐carborane and lithium phenylacetylide. The structure was characterized using FTIR, ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, and gel permeation chromatography. PACS exhibits solubility in common organic solvents. Thermal and oxidative properties were evaluated by thermogravimetric analysis (TGA). Thermoset exhibits extremely thermal and oxidative property and TGA curves show that the temperature of 5% weight loss (Td₅) is 762°C and char yield at 800°C is 94.2% in nitrogen. In air, surprisingly, both Td₅ and char yield at 800°C show slight increase, which is greater than 800°C and 95.6%, respectively. After pyrolysis, the char has no additional weight loss up to 800°C in air. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2498–2503, 2007     

Vinyl polymerization of norbornene with dinuclear diimine nickel dichloride/MAO

Vinyl‐addition polymerization of norbornene was accomplished by two novel dinuclear diimine nickel dichloride complexes in combination with methylaluminoxane (MAO). The activities were moderate. The catalyst structure, Al/Ni molar ratio, solvents, and polymerization temperature all affected the catalytic activities. The obtained polynorbornenes were characterized by ¹H‐NMR, ¹³C‐NMR, FTIR, DSC, WAXD, and intrinsic viscosity measurements. The vinyl‐addition polymers were amorphous but with a short‐range order and high packing density. The polynorbornenes showed glass transition temperatures (T_g) above 240°C and decomposed above 400°C. The catalyst structure and polymerization conditions have effects on the molecular weight and the microstructure of the polymers. The nickel complex with bulkier substituents in the ligand produced polynorbornene with a higher packing density and higher regularity and, therefore, with higher T_g. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3273–3278, 2003     

Silphenylene and silphenylene-siloxane oligomers: Structure-property relationships

Some representative oligomers were prepared by polycondensation reactions of dimethyldichlorosilane with 1,4-di-Grignard reagent prepared from 1,4-dibromobenzene in diethyl ether. The structural characterization of the oligomers was carried out by FTIR and¹H,¹³C, and²⁹Si NMR spectroscopy. TheM _n values were determined by vapor pressure osmometry. TheT _g values were measured by DSC and the thermodegradation process was analyzed by TGA. In all cases the oligomers prepared in the absence of the blocking end group showed siloxane units in the main chain, which were quantified by¹H and²⁹Si NMR.²⁹Si NMR was also used to determine the oligomer sequence. It was possible to correlate the and structure withT _g and with temperature at 3% weight loss. The results agree with these obtained for structurally similar polymers.     

Graft copolymers of lignin with electron poor alkenes

The synthesis of copolymers between lignin and electron poor alkenes is described. Lignin from steam‐exploded pine, from steam‐exploded straw, and organosolv were used as starting materials. Beforehand, lignins were fully characterized by using elemental analysis, ultraviolet spectroscopy, gel permeation chromatography (GPC), Fourier transform infrared (FTIR), and both¹H and ¹³C nuclear magnetic resonance (NMR) spectroscopy. The synthesis of copolymers was performed using a previously described procedure utilizing calcium chloride and hydrogen peroxide as reagents. FTIR of copolymers showed absorptions due to the presence of both lignin and the electron withdrawing group on the alkene. GPC analysis showed the presence of fractions with high molecular weights: the M_z of lignin from pine was 3729 while the copolymer with methyl acrylate showed M_z = 383790. Differential calorimetry showed the presence of glass transitions in the range of ?9 to 4.5°C due to the presence of grafted polyalkene chains. When acrylonitrile was used as starting material DSC analysis of the product showed a glass transition at 119°C, which can be attributed to grafted polyacrylonitrile chain. Lignin from steam explosion could be a good raw material in the preparation of graft copolymers. Furthermore, lignin from pine gave better results than that from straw. Finally, lignin from steam explosion gave better results than organosolv lignin. These results can be explained on the basis of the structural properties of used lignins. Both UV and ¹³C NMR spectra showed that lignin from pine contained a consistent amount of double bonds. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1163–1171, 2003     

Investigation of kinetics of 4‐methylpentene‐1 polymerization using Ziegler–Natta‐type catalysts

The kinetics of 4‐methylpentene‐1 (4MP1) polymerization by use of Ziegler–Natta‐type catalyst systems, M(acac)₃‐AlEt₃ (M = Cr, Mn, Fe, and Co), are investigated in benzene medium at 40°C. The effect of various parameters such as Al/M ratio, reaction time, aging time, temperature, catalyst, and monomer concentrations on the rate of polymerization and yield are examined. The rate of polymerization increased linearly with increasing monomer concentration with first‐order dependence, whereas the rate of polymerization with respect to catalyst concentration is found to be 0.5. For all cases, the polymer yield is maximum at an Al/M ratio of 2. The activation energies obtained from linear Arrhenius plots are in the range of 25.27–33.51 kJ mol^?1. It is found that the aging time to give maximum percentage yield of the polymer varies with the catalyst systems. Based on the experimental results, a plausible mechanism is proposed that envisages a free‐radical mechanism. Characterization of the resulting polymer product, for all the cases, through FTIR, ¹H‐NMR, and ¹³C‐NMR studies, showed isomerized polymeric structures with 1,4‐structure as dominant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2468–2477, 2003     

New fluorine‐containing bissalicylidenimine–titanium complexes for olefin polymerization

Three new titanium complexes bearing salicylidenimine ligands—bis[(salicylidene)‐2,3,5,6‐tetrafluoroanilinato]titanium(IV) dichloride ( 1 ), bis[(3,5‐di‐tert‐butylsalicylidene)‐2,3,5,6‐tetrafluoroanilinato]titanium(IV) dichloride ( 2 ), and bis[(3,5‐di‐tert‐butylsalicylidene)‐4‐trifluoromethyl‐2,3,5,6‐tetrafluoroanilinato]titanium(IV) dichloride ( 3 )—were synthesized. The catalytic activities of 1 – 3 for ethylene polymerization were studied with poly(methylaluminoxane) (MAO) as a cocatalyst. Complex 1 was inactive in ethylene polymerization. Complex 2 at a molar ratio of cocatalyst to pre catalyst of Al_MAO/Ti = 400–1600 showed very high activity in ethylene polymerization comparable to that of the most efficient metallocene complexes and titanium compounds with phenoxy imine and indolide imine chelating ligands. It gave linear high‐molecular‐weight polyethylene [weight‐average molecular weight (M_w) ≥ 1,700,000. weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 4–5] with a melting point of 142°C. The ability of the 2 /MAO system to copolymerize ethylene with hexene‐1 in toluene was analyzed. No measurable incorporation of the comonomer was observed at 1:1 and 2:1 hexene‐1/ethylene molar ratios. However, the addition of hexene‐1 had a considerable stabilizing effect on the ethylene consumption rate and lowered the melting point of the resultant polymer to 132°C. The 2 /MAO system exhibited low activity for propylene polymerization in a medium of the liquid monomer. The polymer that formed was high‐molecular‐weight atactic polypropylene (M_w ～ 870,000, M_w/M_n = 9–10) showing elastomeric behavior. The activity of 3 /MAO in ethylene polymerization was approximately 70 times lower than that of the 2 /MAO system. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1040–1049, 2005     

Method for preparing polyaluminocarbosilane

Polyaluminocarbosilane (PACS) was synthesized directly by the one‐pot reaction of polydimethylsilane (PDMS) with aluminum acetylacetonate [Al(acac)₃] in an autoclave. In this closed system, all the aluminum in Al(acac)₃ was converted into PACS. Therefore, the content of aluminum could be readily controlled quantitatively. On the basis of Fourier transform infrared, ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, and ²⁷Al magic‐angle spinning NMR analysis, the reaction mechanism was proposed as follows: PDMS dissociated during pyrolysis to generate silicon free radicals, and then they reacted with Al(acac)₃ to yield PACS containing (Si? O)_nAl groups (n = 4, 5, or 6). Meanwhile, these reactions resulted in the cleavage of O? C and/or O?C bonds in Al(acac)₃. Some of the free‐radical fragments generated by this cleavage continued to react with the silicon free radicals and were incorporated into the structural units of PACS; the rest of them may have been converted into small oxygen‐containing compounds, which were removed in the subsequent processing after the reactions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Study of the compositional heterogeneity of ethylene/1–hexene copolymers produced over supported catalysts of different composition

Separation into narrow MWD fractions (liquid–liquid fractionation) and preparative TREF (temperature rising elution fractionation) with subsequent analysis of fractions by GPC, FTIR, and ¹³C NMR spectroscopy were used to study the comonomer distribution of ethylene/1–hexene copolymers produced over highly active supported titanium‐ and vanadium‐magnesium catalysts (TMC and VMC) and a supported zirconocene catalyst. These catalysts produce PE with different MWD: M_w/M_n values vary from 2.9 for zirconocene catalyst, 4.0 for TMC, and 15 for VMC. 1‐Hexene increases polydispersity to 25 for copolymer produced over VMC and hardly affects MWD of the copolymer produced over TMC and zirconocene catalysts. The most broad short chain branching distribution (SCBD) was found for ethylene/1–hexene copolymers produced over TMC. VMC and supported zirconocene catalyst produce copolymers with uniform profile of SCB content vs. molecular weight in spite of great differences in M_w/M_n values (22 and 2.5 respectively). TREF data showed that majority of copolymer produced over supported zirconocene catalyst was eluted at 70–90°C (about 85 wt %). In the case of VMC copolymer's fractions were eluted in the broad temperature interval (40–100°C). Accordingly, TREF data indicate a more homogeneous SCBD in copolymer, produced over supported zirconocene catalyst. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Using hydroxypropyl‐β‐cyclodextrin for the preparation of hydrophobic poly(ketoethyl methacrylate) in aqueous medium

This work was committed to the polymerization of hydrophobic ketoethyl methacrylate monomer in aqueous medium in the presence of cyclodextrin, instead of polymerizing the monomer in toxic and volatile organic solvents. For this purpose, a new ketoethyl methacrylate monomer, p‐methylphenacylmethacrylate (MPMA), was synthesized from the reaction of p‐methylphenacylbromide with sodium methacrylate in the presence of triethylbenzylammonium chloride. The monomer was identified with FTIR, ¹H and ¹³C‐NMR spectroscopies. Hydroxypropyl‐β‐cyclodextrin (HPCD) was used to form a water‐soluble host/guest inclusion complex (MPMA/HPCD) with the hydrophobic monomer. The complex was identified with FTIR and NMR techniques and polymerized in aqueous medium using potassium persulfate as initiator. During polymerization the resulting hydrophobic methacrylate polymer precipitated out with a majority of HPCD left in solution and a minority of HPCD bonded on the resulting polymer. The thus‐prepared polymer exhibited little difference from the counterparts obtained in organic solvent in number average molecular weight (M_n), polydispersity (M_w/M_n) and yield. The investigation provides a novel strategy for preparing hydrophobic ketoethyl methacrylate polymer in aqueous medium by using a monomer/HPCD inclusion complex. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Stereochemical and compositional assignments of trans‐4‐methacryloyloxyazobenzene–methyl methacrylate copolymers by one‐ and two‐dimensional NMR spectroscopy

The microstructure of trans‐4‐methacryloyloxyazobenzene–methyl methacrylate copolymers prepared by solution polymerization process using AIBN as initiator is analyzed by one‐and two‐dimensional spectroscopy. Sequence distribution was calculated from the ¹³C(¹H)‐NMR spectra of the copolymers. Comonomer reactivity ratios were determined using the Kelen–Tudos and the nonlinear error‐in‐variables methods are r_A = 1.14 ± 0.08 and r_M = 0.51 ± 0.03; r_A = 1.13 ± 0.1 and r_M = 0.50 ± 0.04, respectively. The sequence distribution of A‐ and M‐centered triads determined from ¹³C(¹H)‐NMR spectra of copolymer is in good agreement with triad concentration calculated from a statistical model. The 2‐D heteronuclear single‐quantum correlation and correlated spectroscopy (TOCSY) was used to analyze the complex ¹H‐NMR spectrum. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3016–3025, 1999     

‘Living’ radical polymerization of styrene with AIBN/FeCl3/PPh3 initiating system via a reverse atom transfer radical polymerization process

Well‐defined polystyrenes with an α‐C(CH₃)₂(CN) and an ω‐chlorine atom end‐groups, and narrow polydispersity (M_n = 3000–4000 g mol⁻¹, M_w/M_n = 1.3–1.4) have been synthesized by a radical polymerization process using 2,2′‐azobisisobutyronitrile(AIBN)/FeCl₃/PPh₃ initiation system. When the ratio of [St]₀:[AIBN]₀:[FeCl₃]₀:[PPh₃]₀ is 200:1:4:12 at 110 °C, the radical polymerization is ‘living’, but the molecular weight of the polymers is not well‐controlled. The polymerization mechanism belongs to a reverse atom transfer radical polymerization (ATRP). Because the polymer obtained is end‐functionalized by a chlorine atom, it can then be used as a macroinitiator to perform a chain extension polymerization in the presence of CuCl/2,2′‐bipyridine catalyst system via a conventional ATRP process. The presence of a chlorine atom as an end‐group was determined by ¹H NMR spectroscopy. © 2000 Society of Chemical Industry     

Polyamides obtained by direct polycondesation of 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl] fluoren‐9‐YL]‐2‐methyl‐phenoxy]aniline with dicarboxylic acids based on a diphenyl‐silane moiety

Polyamides (PAs) containing fluorene, oxyether, and diphenyl‐silane moieties in the repeating unit were synthesized in > 85% yield by direct polycondesation between a diamine and four dicarboxylic acids. Alternatively, one PA was synthesized from an acid dichloride. The diamine 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl]fluoren‐9‐yl]‐2‐methyl‐phenoxy]aniline ( 3 ) was obtained from the corresponding dinitro compound, which was synthesized by nucleophilic aromatic halogen displacement from p‐chloronitrobenzene and 9,9‐bis (4‐hydroxy‐3‐methyl‐phenyl)fluorene ( 1 ). Monomers and polymers were characterized by FTIR and ¹H, ¹³C, and ²⁹Si‐NMR spectroscopy and the results were in agreement with the proposed structures. PAs showed inherent viscosity values between 0.14 and 0.43 dL/g, indicative of low molecular weight species, probably of oligomeric nature. The glass transition temperature (T_g) values were observed in the 188–211°C range by DSC analysis. Thermal decomposition temperature (TDT_10%) values were above 400°C due to the presence of the aromatic rings in the diamine. All PAs showed good transparency in the visible region (>88% at 400 nm) due to the incorporation of the fluorene moiety. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011