Study of jute fiber reinforced polyester composites by dynamic mechanical analysis

Cyanoethylation of jute fibers in the form of nonwoven fabric was studied, and these chemically modified fibers were used to make jute–polyester composites. The dynamic mechanical thermal properties of unsaturated polyester resin (cured) and composites of unmodified and chemically modified jute–polyester were studied by using a dynamic mechanical analyzer over a wide temperature range. The data suggest that the storage modulus and thermal transition temperature of the composites increased enormously due to cyanoethylation of fiber. An increase of the storage modulus of composites, prepared from chemically modified fiber, indicates its higher stiffness as compared to a composite prepared from unmodified fiber. It is also observed that incorporation of jute fiber (both unmodified and modified) with the unsaturated resin reduced the tan δ peak height remarkably. Composites prepared from cyanoethylated jute show better creep resistance at comparatively lower temperatures. On the contrary, a reversed phenomenon is observed at higher temperatures (120°C and above). Scanning electron micrographs of tensile fracture surfaces of unmodified and modified jute–polyester composites clearly demonstrate better fiber–matrix bonding in the case of the latter. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1505–1513, 1999     

Microstructure and fracture behavior of (co)injection‐molded polyamide 6 composites with short glass/carbon fiber hybrid reinforcement

The mechanical and fracture properties of injection molded short glass fiber)/short carbon fiber reinforced polyamide 6 (PA 6) hybrid composites were studied. The short fiber composites of PA 6 glass fiber, carbon fiber, and the hybrid blend were injection molded using a conventional machine whereas the two types of sandwich skin–core hybrids were coinjection molded. The fiber volume fraction for all formulations was fixed at 0.07. The overall composite density, volume, and weight fraction for each formulation was calculated after composite pyrolysis in a furnace at 600°C under nitrogen atmosphere. The tensile, flexural, and single‐edge notch‐bending tests were performed on all formulations. Microstructural characterizations involved the determination of thermal properties, skin–core thickness, and fiber length distributions. The carbon fiber/PA 6 (CF/PA 6) formulation exhibits the highest values for most tests. The sandwich skin‐core hybrid composites exhibit values lower than the CF/PA 6 and hybrid composite blends for the mechanical and fracture tests. The behaviors of all composite formulations are explained in terms of mechanical and fracture properties and its proportion to the composite strength, fiber orientation, interfacial bonding between fibers and matrix, nucleating ability of carbon fibers, and the effects of the skin and core structures. Failure mechanisms of both the matrix and the composites, assessed by fractographic studies in a scanning electron microscope, are discussed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 957–967, 2005     

Surface modification of aramid fibers with γ‐ray radiation for improving interfacial bonding strength with epoxy resin

Co⁶⁰ γ‐ray radiation as a simple and convenient method for surface modification of Armos aramid fibers was introduced in this article. Two kinds of gas mediums, N₂ and air, were chosen to modify aramid fiber surface by γ‐ray irradiation. After fiber surface treatment, the interlaminar shear strength values of aramid/epoxy composites were enhanced by about 17.7 and 15.8%, respectively. Surface elements of aramid fibers were determined by XPS, the analysis of which showed that the ratio of oxygen/carbon was increased. The crystalline state of aramid fibers was determined by X‐ray diffraction instrument. The surface topography of fibers was analyzed by atomic force microscopy and scanning electron microscope. The degree of surface roughness and the wettability of fiber surface were both enhanced by γ‐ray radiation. The results indicated that γ‐ray irradiation technique, which is a suitable way of batch process for industrialization, can significantly improve the surface properties of aramid fibers reinforced epoxy resin matrix composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of layering pattern on the physical,mechanical, and thermal properties of jute/bagasse hybrid fiber‐reinforced epoxy novolac composites

In this study, randomly oriented short jute/bagasse hybrid fiber‐reinforced epoxy novolac composites were prepared by keeping the relative volume ratio of jute and bagasse of 1:3 and the total fiber loading 0.40 volume fractions. The effect of jute fiber hybridization and different layering pattern on the physical, mechanical, and thermal properties of jute/bagasse hybrid fiber‐reinforced epoxy novolac composites was investigated. The hybrid fiber‐reinforced composites exhibited fair water absorption and thickness swelling properties. To investigate the effect of layering pattern on thermomechanical behavior of hybrid composites, the storage modulus and loss factor were determined using dynamic mechanical analyzer from 30 to 200°C at a frequency of 1 Hz. The fracture surface morphology of the tensile samples of the hybrid composites was performed by using scanning electron microscopy. The morphological features of the composites were well corroborated with the mechanical properties. Thermogravimetric analysis indicated an increase in thermal stability of pure bagasse composites with the incorporation of jute fibers. The incorporation of hybrid fibers results better improvement in both thermal and dimensional stable compared with the pure bagasse fiber composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Study on mechanical properties of perlite‐filled gamma‐irradiated polypropylene

This study covers the preparation and characterization of perlite‐filled polypropylene (PP). The compositions of 15, 30, and 50 % by weight perlite–PP composites were prepared by melt‐mixing. The PP used in this study was either applied in the virgin form or γ‐irradiated in air at the doses of 10, 25, 50, and 100 kGy to determine the effect of oxidative degradation in composite properties. Furthermore, the active sites containing oxygen produced by γ‐irradiation in PP may provide a possible enhancement by the interfacial interaction between perlite and PP. An initial sharp drop in torque readings during the melt‐mixing of perlite–PP composite preparation indicated an extensive chain scission and degradation by γ‐irradiation. The thermal properties of the composites were characterized by DSC. The ultimate tensile strength and elongation and also impact strength decreased in all composites with γ‐irradiation. Yet, these changes appeared not to be faster than was the change in unfilled PP upon irradiation. Scanning electron microscopy revealed an interfacial adhesion between perlite and irradiated PP while virgin PP did not show any evidence of adhesion. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2670–2678, 2001     

Modification of cellulose fibers with functionalized silanes: Effect of the fiber treatment on the mechanical performances of cellulose–thermoset composites

Unsaturated polyester and epoxy resin matrices were filled with silane‐treated cellulose fibers and the ensuing composites were tested in terms of mechanical properties before and after accelerated aging consisting of their immersion into water. The coupling agents used were γ‐aminopropyltriethoxysilane (APS), γ‐methacrylopropyltrimethoxysilane (MPS), hexadecytrimethoxysilane, and γ‐mercaptopropyltrimethoxysilane (MRPS) and those containing reactive functions capable of reacting at one end with the fibers and at the other with the matrix, namely, APS, MPS, and MRPS, were more efficient in improving the mechanical properties of the composites. The immersion into water induced a drastic loss of mechanical properties of the materials. The water uptake of the composites was also studied and showed that the silane treatment was poorly efficient in preventing cellulose from water absorption. The fracture surfaces were inspected by scanning electron microscopy, which confirmed the quality of the interface. These observations were in agreement with the results obtained from the dynamic mechanical characterization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 974–984, 2005     

Effect of short carbon fiber content on the mechanical properties of TiB2-based composites prepared by spark plasma sintering

In this study, TiB₂-30 vol% SiC composites containing 0, 5, 10, and 15 vol% short carbon fibers (C_f) were produced by spark plasma sintering (SPS). The effect of carbon fiber content on microstructure, density, and mechanical properties (micro-hardness and flexural strength) of the fabricated composites was studied. Scanning electron microscopy (SEM) results indicated that the fibers were uniformly dispersed in the TiB₂–SiC matrix using wet ball milling before SPS process. Fully dense TiB₂–SiC–C_f composites were achieved by SPS process at 1900°C for 10 min under 30 MPa. With the addition of fibers, the relative density of the composites did not change considerably. Mechanical tests revealed that microhardness was reduced about 19% by the incorporation of carbon fibers, whereas the flexural strength improved significantly. However, the flexural strength diminished by adding carbon fibers above to critical value (5 vol%) due to residual thermal stresses, nonhomogeneous structure and graphitization of carbon fibers. It was found that the composite with 5 vol% C_f had the highest flexural strength (482 MPa), which was enhanced by 20% compared with the TiB₂–SiC composite.     

短切碳纤维对聚苯腈/碳纤维复合材料性能的影响

利用碳纤维（CF）增强聚苯腈（PN）树脂制备一系列PN/CF复合材料,利用万能试验机和动态热机械分析仪（DMA）,研究短CF含量、长度与偶联剂种类对PN树脂力学性能的影响。结果表明,采用苯基三乙氧基硅烷作为偶联剂时力学性能和热稳定性达到最佳水平,相较于未经偶联剂改性PN/CF复合材料的储能模量提高了22.2%,热失重5%温度（Td5%）提高了33.1%;随着CF掺杂量的增加,材料力学性能呈现先增大后减小趋势,在0.3%（质量分数,下同）时获得了最优异力学性能,相较于PN树脂,其弯曲强度提高了38.4%,弯曲模量提升了97.7%;CF长度为6 mm时材料的弯曲强度和储能模量优于CF长度为3 mm时的材料。     

Influence of γ‐ray irradiation on structure and properties of PAN precursor fibers

To improve the oxidative efficiency of polyacrylonitrile (PAN) precursors, modification of PAN precursors was employed by gamma ray irradiation. Effects of irradiation on the structure and properties of PAN precursors were investigated. The results showed that cyclized structure in the precursors was formed after γ‐ray irradiation. Meanwhile, irradiation could reduce the heat evolved, relax the exothermic behavior, decrease the mechanical properties and enhance the density of PAN fibers. It is supposed that the modification of γ‐ray irradiation could remarkably accelerate the stabilization process of PAN precursors and reduce the production cost of resulting carbon fibers. POLYM. ENG. SCI., 56:1313–1318, 2016. © 2016 Society of Plastics Engineers     

Mechanical and thermal shock properties of Cf/SiBCN composite: Effect of sintering densification and fiber coating

In this work, resin-derived carbon coating was prepared on carbon fibers by polymer impregnation pyrolysis method, then silicoboron carbonitride powder was prepared by mechanical alloying, and finally carbon fiber-reinforced silicoboron carbonitride composites were prepared by hot-pressing process. The effects of sintering densification and fiber coating on microstructure, mechanical properties, thermal shock resistance, and failure mechanisms of the composites were studied. Fiber bridging hinders the sintering densification, causing more defects in fiber-dense area and lower strength. However, higher sintering temperature (1800–2000°C) can improve mechanical properties significantly, including bending strength, vickers hardness, and elastic module, because further sintering densification enhances matrix strength and fiber/matrix bonding strength, while the change of fracture toughness is not obvious (2.24–2.38 MPa·m^1/2) due to counteraction of higher debonding resistance and less pull-out length. However, fiber coating improves fracture toughness greatly via protecting carbon fibers from chemical corrosion and damage of thermal stress and external stress. Due to lower coefficient of thermal expansion, lower fiber loading ratio, less stress concentration at the fiber/matrix interface, and better defect healing effect, lower sintering temperature favors thermal shock resistance of composites, and thermal shock recession mechanisms are the damage of interface.     

Thermal,mineralogical, and microstructural characterizations of irradiated polymer blended cement mortar composites

In this study, the effects of styrene–acrylic ester (SAE), nanocalcined clay (NCC), and irradiation dose on the thermal, mineralogical, and microstructural characterizations of irradiated polymer‐blended cement mortar composites have been investigated. The composites were prepared by partial replacement of cement with 5 and 10% NCC and mixed with sand, SAE latex was added with different ratios (2, 4, 6, 8, 10, and 15%); the composites were subjected to various doses of γ‐irradiation ranged from 10 to 50 kGy. Physicomechanical properties, thermogravimetric analysis, X‐ray diffractometry, and scanning electron microscopy techniques were carried out. Mechanical investigation manifested that composites loaded with SAE up to 8% showed the best mechanical performance as compared with composites contains 10 and 15% SAE. POLYM. COMPOS., 36:1849–1858, 2015. © 2014 Society of Plastics Engineers     

Polypropylene/(waste tire dust)/(short glass fiber composites): Effects of silane coupling agent and dynamic vulcanization

Polypropylene (PP) and waste tire dust (WTD) were internally mixed with various amounts of short glass fiber (SGF) to form a series of PP/WTD/SGF composites, with and without addition of a silane coupling agent, γ‐aminopropyltrimethoxysilane (γ‐APS), and dynamic vulcanization (DV). The effects of γ‐APS, and DV on the properties of the composites were investigated. The PP/WTD/SGF composites were prepared by using WTD of 250–500 μm dimensions at different SGF loadings (5, 10, 15, and 20 parts per hundred parts of polymer). The results revealed that the addition of γ‐APS and DV increased the equilibrium torque, tensile properties except elongation at break, and swelling resistance of the composites. Because of the incorporation of γ‐APS and DV, the thermal stability was enhanced, and scanning electron micrographs showed improved adhesion between the PP/WTD matrix and SGF. Analysis by Fourier transform infrared was performed on the composites with and without addition of γ‐APS and DV in order to study the interactions among the PP, WTD, SGF, and the amino functional group of the silane. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers.     

Carbon fiber reinforced phenolic Resin/Silica ceramer composites—processing,mechanical and thermal properties

Phenolic/silica ceramers were prepared by the sol‐gel method. Carbon fiber reinforced phenolic/silica ceramer composites with high thermal resistance were fabricated. Tetraethyl orthosilicate (TEOS) was used as a monomer for sol‐gel system. Different ratios of the sol‐gel solutoins and phenolic resins were adopted and the resulting ceramers were used as matrices for carbon fiber reinforced composites. The mechanical and thermal properties of the fabricated composites were studied. The results show that the incorporation of inorganic ingredients into the phenolic resins will increase the thermal resistance of the fabricated composites but not affect the flexural strength of the carbon fiber reinforced phenolic/silica ceramer composites up to 60 wt%. The morphologies of the ceramer matrices were examined by SEM. SiO₂ particles from at the gaps between fibers for higher inorganic contents.     

碳纤维增强聚丙烯复合材料的制备及性能

采用硝酸液相氧化法改性短切碳纤维(NCF),用以制备聚丙烯(PP)复合材料。以纤维含量和纤维种类为变量,通过万能力学试验机、熔体流动速率试验机、差示扫描量热、X射线衍射、扫描电子显微镜等研究它们对材料力学性能、流动性能、熔融温度以及结晶性能的影响。实验结果表明,纤维的含量影响纤维在基体中的分布,进而显著影响材料的性能,且含量在10%至20%区内时具有较好的增强效果;NCF与PP的界面具有更强的粘附力,这提升了复合材料的力学强度,降低了材料的断裂伸长率,降低了材料的熔融流动速率,提升了材料的结晶温度与结晶度,略微降低了材料的熔融温度;纤维含量与纤维种类均对材料的结晶晶型无明显影响。     

The effect of filler concentration on the electrical,thermal, and mechanical properties of carbon particle and carbon fiber‐reinforced poly(styrene‐co‐acrylonitrile) composites

Composite materials of poly (styrene‐co‐acrylonitrile) (luran) matrix with carbon fibers (CF)/carbon particles (CP) were prepared and their properties were evaluated. The mechanical and thermal properties of these composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). Although, by increasing the filler concentration no significant difference was found in melting and crystallization temperatures of the luran. The storage and tensile modulus of the composites increased linearly with filler concentration up to 40 wt % that was approximately three times higher than that of the virgin luran. There is a shift in glass transition temperature of the composite with increasing the filler concentration and the damping peak became flatter that indicated the effectiveness of the filler–matrix interaction. The volume resistivity and thermal conductivity (TC) of the composites were also measured. At a given carbon filler content the CF–Luran composites have much less volume resistivity as compared to CP–Luran composites. The decreased percolation threshold and volume resistivity in case of CF–Luran composites indicated that conductive paths existed in the composites. The conductive pathways were probably formed through interconnection of the carbon fillers. The volume resistivity was also decreased as a function of temperature. The thermal conductivity was increased linearly as a function of temperature with increasing filler concentration up to 40% of CF and CP. This increase was more profound in case of CF–Luran as compared to CP–Luran composites. This was owing to greater thermal networks of fibers as compared to particles. POLYM. COMPOS., 28:186–197, 2007. © 2007 Society of Plastics Engineers     

Concentration effect of γ‐glycidoxypropyltrimethoxysilane on the mechanical properties of glass fiber–epoxy composites

In this study, glass fibers were modified using γ‐glycidoxypropyltrimethoxysilane of different concentrations to improve the interfacial adhesion at interfaces between fibers and matrix. Effects of γ‐glycidoxypropyltrimethoxysilane on mechanical properties and fracture behavior of glass fiber/epoxy composites were investigated experimentally. Mechanical properties of the composites have been investigated by tensile tests, short beam tests, and flexural tests. The short‐beam method was used to measure the interlaminar shear strength (ILSS) of laminates. The tensile and flexural properties of composites were characterized by tensile and three‐point bending tests, respectively. The fracture surfaces of the composites were observed with a scanning electron microscope. On comparing the results obtained for the different concentrations of silane solution, it was found that the 0.5% GPS silane treatment provided the best mechanical properties. The ILSS value of heat‐cleaned glass fiber reinforced composite is enhanced by ∼59% as a result of the glass fiber treatment with 0.5% γ‐GPS. Also, an improvement of about 37% in tensile strength, about 78% in flexural strength of the composite with the 0.5% γ‐GPS treatment of glass fibers was observed. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Thermal decomposition behavior of γ‐irradiated poly(vinyl acetate)/poly(methyl methacrylate) miscible blends

Miscible polymer blends based on various ratios of poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) were prepared in film form by the solution casting technique using benzene as a common solvent. The thermal decomposition behavior of these blends and their individual homopolymers before and after γ‐irradiation at various doses (50–250 kGy) was investigated. The thermogravimetric analysis technique was utilized to determine the temperatures at which the maximum value of the rate of reaction (T_max) occurs and the kinetic parameters of the thermal decomposition. The rate of reaction curves of the individual homopolymers or their blends before or after γ‐ irradiation displayed similar trends in which the T_max corresponding to all polymers was found to exist in the same position but with different values. These findings and the visual observations of the blend solutions and the transparency of the films gave support to the complete miscibility of these blends. Three transitions were observed along the reaction rate versus temperature curves; the first was around 100–200°C with no defined T_max, which may arise from the evaporation of the solvent. The second T_max was in the 340–380°C range, which depended on the polymer blend and the γ‐irradiation condition. A third transition was seen in the rate of reaction curves only for pure PVAc and its blends with PMMA with ratios up to 50%, regardless of γ‐ irradiation. We concluded that γ‐irradiation improved the thermal stability of PVAc/PMMA blends, even though the PMMA polymer was degradable by γ irradiation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1773–1780, 2006     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Tribological behavior of short‐fiber‐reinforced polyimide composites under dry‐sliding and water‐lubricated conditions

Polyimide composites reinforced with short‐cut fibers such as carbon, glass, and quartz fibers were fabricated by the polymerization of monomer reactants process. The mechanical properties of the composites with different fiber contents were evaluated. The friction and wear properties of the polyimide and its composites were investigated under dry‐sliding and water‐lubricated conditions. The results indicated that the short‐carbon‐fiber‐reinforced polyimide composites had better tensile and flexural strengths and improved tribological properties in comparison with glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. The incorporation of short carbon fibers into the polyimide contributed to decreases in the friction coefficient and wear rate under both dry and water‐lubricated conditions and especially under water lubrication because of the boundary lubrication effect of water. The polyimide and its composites were characterized by plastic deformation, microcracking, and spalling under both dry and water‐lubricated conditions, which were significantly abated under the water‐lubricated condition. The glass and quartz fibers were easily abraded and broken; the broken fibers transferred to the mating metal surface and increased the surface roughness of mating stainless steel, which led to the wear rate increasing for the glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Influence of γ‐irradiation on poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) was γ‐irradiated (5–20 kGy) by a ¹³⁷Cs source at room temperature in air. The changes in the molecular structure attributed to γ‐irradiation were studied by mechanical testing (flexure and hardness), size‐exclusion chromatography, differential scanning calorimetry, thermal gravimetric analysis, and both Fourier transform infrared and solution ¹³C‐NMR spectroscopy. Scanning electron microscopy was used to investigate the influence of the dose of γ rays on the fracture behavior of PMMA. The experimental results confirm that the PMMA degradation process involves chain scission. It was also observed that PMMA presents a brittle fracture mechanism and modifications in the color, becoming yellowish. The mechanical property curves show a similar pattern when the γ‐radiation dose increases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 886–895, 2002