Effects of poly(methyl methacrylate)‐based low‐profile additives on the properties of cured unsaturated polyester resins. II. Volume shrinkage characteristics and internal pigmentability

The effects of three series of self‐synthesized poly(methyl methacrylate) (PMMA)‐based low‐profile additives (LPAs), including PMMA, poly(methyl methacrylate‐co‐butyl acrylate), and poly(methyl methacrylate‐co‐butyl acrylate‐co‐maleic anhydride) with different chemical structures and MWs on the volume shrinkage characteristics and internal pigmentability for low‐shrink unsaturated polyester (UP) resins during curing were investigated by an integrated approach of static phase characteristics of the ternary styrene (ST)/UP/LPA system, reaction kinetics, cured‐sample morphology, microvoid formation, and property measurements. The relative volume fraction of microvoids generated during the cure was controlled by the stiffness of the UP resin used, the compatibility of the uncured ST/UP/LPA systems, and the glass‐transition temperature of the LPAs used. On the basis of the Takayanagi mechanical model, the LPA mechanism on volume shrinkage control, which accounted for phase separation and microvoid formation, and factors leading to both a good volume shrinkage control and acceptable internal pigmentability for the molded parts are discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3388–3397, 2004     

Effects of reactive low‐profile additives on the volume shrinkage and internal pigmentability for low‐temperature cure of unsaturated polyester

The effects of reactive poly(vinyl acetate)‐block‐poly(methyl methacrylate) (PVAc‐b‐PMMA) and poly(vinyl acetate)‐block‐polystyrene (PVAc‐b‐PS) as low‐profile additives (LPA) on the volume shrinkage characteristics and internal pigmentability for low‐shrink unsaturated polyester resins (UP) during the cure at 30°C were investigated. These reactive LPAs, which contained peroxide linkages in their backbones, were synthesized by suspension polymerizations, using polymeric peroxides (PPO) as initiators. Depending on the LPA composition and molecular weight, the reactive LPA could lead to a reduction of cyclization reaction for UP resin during the cure, and would be favorable for the decrease of intrinsic polymerization shrinkage after the cure. The experimental results have been explained by an integrated approach of measurements for the static phase characteristics of the styrene (ST)/UP/LPA system, reaction kinetics, cured sample morphology, and microvoid formation by using differential scanning calorimetry (DSC), scanning electron microscopy (SEM), optical microscopy (OM), and image analysis. Based on the Takayanagi mechanical model, factors leading to both a good volume shrinkage control and acceptable internal pigmentability for the molded parts have been explored. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 967–979, 2006     

Effects of poly(vinyl acetate) and poly(vinyl chloride‐ co‐vinyl acetate) low‐profile additives on properties of cured unsaturated polyester resins. I. Volume shrinkage characteristics and internal pigmentability

Three series of self‐synthesized poly(vinyl acetate)‐based low‐profile additives (LPAs) with different chemical structures and molecular weights, including poly(vinyl acetate), poly(vinyl chloride‐co‐vinyl acetate), and poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride), were studied. Their effects on the volume shrinkage characteristics and internal pigmentability for low‐shrink unsaturated polyester (UP) resins during cure were investigated. The experimental results were examined with an integrated approach involving measurements of the static phase characteristics of the ternary styrene/UP/LPA system, the reaction kinetics, the cured sample morphology, and microvoid formation by using differential scanning calorimetry, scanning electron microscopy, optical microscopy, and image analysis. Based on the Takayanagi mechanical model, factors leading to both good volume shrinkage control and acceptable internal pigmentability for the molded parts were explored. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3336–3346, 2003     

Effects of reactive low‐profile additives on the properties of cured unsaturated polyester resins. II. Glass‐transition temperature and mechanical properties

The effects of reactive poly(methyl methacrylate) (PMMA) and poly(vinyl acetate)‐block‐poly(methyl methacrylate) (PVAc‐b‐PMMA) as low‐profile additives (LPAs) on the glass‐transition temperature and mechanical properties of low‐shrink unsaturated polyester resin (UP) were investigated by an integrated approach of determining static phase characteristics, reaction kinetics, cured sample morphology, and property measurements. The factors that, according to Takayanagi mechanical models, control the glass‐transition temperature in each phase region of the cured samples, as identified by both the thermally stimulated currents method and dynamic mechanical analysis, and the mechanical properties are discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 867–878, 2006     

Effects of poly(methyl methacrylate)‐based low‐profile additives on the properties of cured unsaturated polyester resins. I. Miscibility,curing behavior,and glass‐transition temperatures

The effects of three series of self‐synthesized poly(methyl methacrylate) (PMMA)‐based low‐profile additives (LPAs), including PMMA, poly(methyl methacrylate‐co‐butyl acrylate), and poly(methyl methacrylate‐co‐butyl acrylate‐co‐maleic anhydride), with different chemical structures and MWs on the miscibility, cured‐sample morphology, curing kinetics, and glass‐transition temperatures for styrene (ST)/unsaturated polyester (UP) resin/LPA ternary systems were investigated by group contribution methods, scanning electron microscopy, differential scanning calorimetry (DSC), and dynamic mechanical analysis, respectively. Before curing at room temperature, the degree of phase separation for the ST/UP/LPA systems was generally explainable by the calculated polarity difference per unit volume between the UP resin and LPA. During curing at 110°C, the compatibility of the ST/UP/LPA systems, as revealed by cured‐sample morphology, was judged from the relative magnitude of the DSC peak reaction rate and the broadness of the peak. On the basis of Takayanagi's mechanical models, the effects of LPA on the final cure conversion and the glass‐transition temperature in the major continuous phase of ST‐crosslinked polyester for the ST/UP/LPA systems was also examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3369–3387, 2004     

Effects of chemical structure of polyurethane‐based low‐profile additives on the miscibility,curing behavior,volume shrinkage,glass transition temperatures,and mechanical properties for styrene/unsaturated polyester/low‐profile additive ternary systems. I: Miscibility,curing behavior,and volume shrinkage

The effects of chemical structure and molecular weight of three series of thermoplastic polyurethane‐based (PU) low‐profile additives (LPA) on the miscibility of styrene (ST)/unsaturated polyester (UP) resin/LPA ternary systems prior to reaction were investigated by using the Flory‐Huggins theory and group contribution methods. The reaction kinetics during the cure at 110°C and the cured sample morphology were also studied by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM), respectively. The phase‐separation characteristics of ST/UP/LPA systems during the cure, as revealed by the cured‐sample morphology, and the DSC reaction‐rate profile, could be generally predicted by the calculated upper critical solution temperature for the uncured ST/UP/LPA systems. Finally, based on the measurements for volume change and microvoid formation, volume shrinkage characteristics for the cured ST/UP/LPA systems have been explored. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 543–557, 2000     

Effects of poly(vinyl acetate) and poly(vinyl chloride‐co‐vinyl acetate) low‐profile additives on properties of cured unsaturated polyester resins. II. glass‐transition temperatures and mechanical properties

Three series of self‐synthesized poly(vinyl acetate)‐based low‐profile additives (LPAs), including poly(vinyl acetate), poly(vinyl chloride‐co‐vinyl acetate), and poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride), with different chemical structures and molecular weights were studied. Their effects on the glass‐transition temperatures and mechanical properties for thermoset polymer blends made from styrene, unsaturated polyester, and LPAs were investigated by an integrated approach of the static phase characteristics, cured sample morphology, reaction kinetics, and property measurements. Based on Takayanagi mechanical models, the factors that control the glass‐transition temperature in each phase region of the cured samples and the mechanical properties are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3347–3357, 2003     

Effects of chemical structure of polyurethane‐based low‐profile additives on the miscibility,curing behavior,volume shrinkage,glass transition temperatures,and mechanical properties for styrene/unsaturated polyester/low‐profile additive ternary systems. II: Glass transition temperatures and mechanical properties

The effects of three series of thermoplastic polyurethane‐based (PU) low‐profile additives (LPA) with different chemical structures and molecular weights on the glass transition temperatures and mechanical properties for thermoset polymer blends made from styrene (ST), unsaturated polyester (UP), and LPA have been investigated by an integrated approach of static phase characteristics‐cured sample morphology‐reaction conversion‐property measurements. The three series of PU used were made from 2,4‐tolylene di‐isocyanate (2,4‐TDI) and varied diols, namely polycaprolactone diol (PCL), poly(diethylene adipate) diol (PDEA), and poly(propylene glycol) diol (PPG), respectively, while the two UP resins employed were synthesized from maleic anhydride (MA) and 1,2‐propylene glycol (PG) with and without modification by phthalic anhydride (PA). Based on the Takayanagi mechanical models, factors that control the glass transition temperature in each phase region of cured samples, as identified by the method of thermally stimulated currents (TSC), and mechanical properties will be discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 558–568, 2000     

Control of shrinkage and final conversion of vinyl ester resins cured in low‐temperature molding processes

Vinyl ester resin is a major thermoset polymer used in low‐temperature composite manufacturing processes such as the Seemann composite resin infusion‐molding process (SCRIMP). Volume shrinkage and residual styrene are important concerns for composites produced in such processes. A low‐shrinkage additive (LSA) is a typical agent added to control the volume shrinkage of vinyl ester resins during molding. In this study, the effects of LSA content and the temperature profile (the temperature gradient and peak temperature) on the volume shrinkage control of a vinyl ester resin were investigated. The reaction kinetics of the resin system were also studied. We achieved good volume shrinkage control if we raised the curing temperature slowly to allow sufficient time for phase separation and if the curing temperature reached a high value after phase separation to allow microvoid formation. On the basis of experimental results, we designed an improved SCRIMP to increase resin conversion, reduce resin shrinkage, and produce composites with better properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1486–1496, 2003     

Hydrolytic stability of cured urea‐formaldehyde resins modified by additives

Urea‐formaldehyde (UF) resins are prone to hydrolysis that results in low‐moisture resistance and subsequent formaldehyde emission from UF resin‐bonded wood panels. This study was conducted to investigate hydrolytic stability of modified UF resins as a way of lowering the formaldehyde emission of cured UF resin. Neat UF resins with three different formaldehyde/urea (F/U) mole ratios (1.4, 1.2, and 1.0) were modified, after resin synthesis, by adding four additives such as sodium hydrosulfite, sodium bisulfite, acrylamide, and polymeric 4,4′‐diphenylmethane diisocyanate (pMDI). All additives were added to UF resins with three different F/U mole ratios before curing the resin. The hydrolytic stability of UF resins was determined by measuring the mass loss and liberated formaldehyde concentration of cured and modified UF resins after acid hydrolysis. Modified UF resins of lower F/U mole ratios of 1.0 and 1.2 showed better hydrolytic stability than the one of higher F/U mole ratio of 1.4, except the modified UF resins with pMDI. The hydrolytic stability of modified UF resins by sulfur compounds (sodium bisulfate and sodium hydrosulfite) decreased with an increase in their level. However, both acrylamide and pMDI were much more effective than two sulfur compounds in terms of hydrolytic stability of modified UF resins. These results indicated that modified UF resin of the F/U mole ratio of 1.2 by adding acrylamide was the most effective in improving the hydrolytic stability of UF resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Control of shrinkage and residual styrene of unsaturated polyester resins cured at low temperatures: I. Effect of curing agents

In low temperature molding processes, control of resin shrinkage and residual monomer is an important concern. The presence of low profile additives (LPAs) can reduce the shrinkage of unsaturated polyester (UP)/styrene (St) resins under proper processing conditions but may increase the residual styrene content. A systematic study was carried out to investigate the effect of the initiator system and reaction temperature on sample morphology, final resin conversion, and resin shrinkage of UP resins with LPA. It was found that the final conversion of the resin system could be improved by using dual initiators. The effect is more obvious at low temperatures. Volume shrinkage measurements of the resin system initiated with dual initiators revealed that good LPA performance was achieved at low (e.g. 35 °C) and high (e.g. 100 °C) temperatures but not at intermediate ones. This can be explained by how temperature affects phase separation, reaction kinetics in the LPA-rich and UP-rich phases, micro-void formation, and thermal expansion.     

Infrared laser‐ignited horizontal frontal polymerization of versatile unsaturated polyester resins

Infrared laser‐ignited horizontal frontal polymerization is applied for the synthesis of unsaturated polyester resin (UPER) by copolymerizing unsaturated polyester with styrene (St), methyl methacrylate (MMA), and 2‐dimethylamino ethyl methacrylate (DMAEMA) monomers. Dependence of frontal velocity and temperature on the initiator and monomer concentration is discussed for St‐based UPER. These resins have also been characterized by Fourier transform infrared, thermogravimetric analysis, and scanning electron microscopy. The results reveal St‐based resins have superior crosslinked networks. Besides, the thermo‐pH responsiveness behaviors of DMAEMA‐based resins are demonstrated by swelling measurements under the conditions of different temperatures and pH values. Moreover, by introducing CdSe@ZnS quantum dots and CsPbBr₃ perovskites into St‐ and MMA‐based resins, respectively, we realize the in situ generation of CdSe@ZnS‐UPER and CsPbBr₃‐UPER composites with good fluorescence properties and fluorescent stability, which have potential application in optoelectronic devices such as light‐emitting diode and perovskite solar cells. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45935.     

Kinetics of thermal decomposition of unsaturated polyester resins with reduced flammability

In this article, the kinetics of thermal decomposition of unsaturated maleic–phthalic polyester resins, flame‐retarded with zinc hydroxystannate, was studied by thermogravimetric analysis at different heating rates. At the first stage, it was found, on the basis of isoconversional analysis by the methods of Friedman and of Ozawa–Flynn–Wall, that the value of the (apparent) activation energy (E) characteristically changes in three steps during the degradation. Further kinetic studies using nonlinear regression methods revealed the best fits for both pristine and stabilized resins. It was observed that the course of E versus the degree of conversion (α) during degradation of zinc hydroxystannate‐containing resins (α > 0.8) was characterized by higher values of E—this phenomenon can be explained in terms of the flame‐retardation action of zinc hydroxystannate, which is believed to operate primarily in the condensed phase. At the next stage, kinetic analysis by the nonregression method was performed to find the kinetic model [f(α) function] of the decomposition process; hence, for pristine resin, the best fit was found for the Avrami–Yerofeeyev model (nuclei growth), and for stabilized samples, the nth‐order function with catalysis proved to be the best approximation. The obtained kinetic parameters in the form of E, the preexponential factor A, and the model function f(α) allow a prediction of the polyester resin's thermal behavior in an extrapolated range of degree of conversion, time, and temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2851–2857, 2003     

Control of volume shrinkage and residual styrene of unsaturated polyester resins cured at low temperatures. II. Effect of comonomer

The effect of a comonomer, methyl methacrylate (MMA), on volume shrinkage and residual styrene content of an unsaturated polyester (UP) resin with low profile additives (LPAs) cured at low temperature was investigated by an integrated reaction kinetics-morphology-property analysis. MMA affects the volume shrinkage and residual styrene content differently depending on MMA to styrene (St) CC bond molar ratio. At low MMA/St ratio, residual styrene decreases and the volume shrinkage of the resin system remains unchanged. At high MMA/St ratio, residual styrene can be substantially reduced, but the resin system suffers poor volume shrinkage control. Reactivity of the comonomer MMA and its compatibility to other components in the resin system can explain the observed results. A series of Seemann composites resin infusion molding process (SCRIMP) were conducted to study the relationship among materials, processing, and properties of molded composites in low temperature curing processes.     

Mechanical characterization and chemical resistances of cured unsaturated polyester resins modified with vinyl ester resins based on recycled poly(ethylene terephthalate)

Unsaturated polyester resin (UP) was prepared from glycolyzed oligomer of poly(ethylene terephthalate) (PET) waste based on diethylene glycol (DEG). New diacrylate and dimethacrylate vinyl ester resins prepared from glycolysis of PET with tetraethylene glycol were blended with UP to study the mechanical characteristics of the cured UP. The vinyl ester resins were used as crosslinking agents for unsaturated polyester resin diluted with styrene, using free‐radical initiator and accelerator. The mechanical properties of the cured UP resins were evaluated. The compressive properties of the cured UP/styrene resins in the presence of different vinyl ester concentrations were evaluated. Increasing the vinyl ester content led to a pronounced improvement in the compression strength. The chemical resistances of the cured resins were evaluated through hot water, solvents, acid, and alkali resistance measurements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3175–3182, 2007     

Improving the heat‐resistance and toughness performance of phenolic resins by adding a rigid aromatic hyperbranched polyester

An aromatic hyperbranched polyester (AHBP) was synthesized by melt polycondensation from diphenolic acid and characterized by Fourier transform infrared spectrum (FTIR) spectra. The degree of branching (DB) value of AHBP calculated from the ¹³C‐NMR spectroscopy was 0.67. The number‐average molecular weight (M_n) and weight‐average molecular weight (M_w) of AHBP were 1792 and 4480 g/mol, respectively. Novel phenolic resins modified with AHBP (PR/AHBP) were then prepared, in which AHBP was used as toughener of phenolic resins. The effect of AHBP on the thermal properties of phenolic resins was studied by means of differential scanning calorimetry (DSC), thermal gravimetric analyses (TGA), and heat deformation temperature tests. The modified resins presented higher glass transition temperature (T_g) than the unmodified system due to that the rigid backbone structure of AHBP with a great deal of the benzene ring groups restricted the mobility of the chain segments of macromolecules. The DSC, scanning electron microscopy (SEM) analyses showed that AHBP had good compatibility with phenolic resin, and the modified resins showed ductile fracture. The results of mechanical performance measurements exhibited that the impact strength of PR/AHBP containing 15 wt % AHBP was about 130% higher than that of the neat phenolic resin, suggesting that the toughness of PR/AHBP was significantly improved by the addition of AHBP. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42734.     

不饱和聚酯树脂微乳液的研究(Ⅰ)不饱和聚酯树脂的微乳化

合成了不同磺酸盐含量的三种不饱和聚酯，通过拟三元相图分析磺酸盐含量、苯乙烯、不同正构醇和水组成的体系对微乳区域的影响。研究结果表明，磺酸盐不饱和聚酯同苯乙烯互溶的前提下，磺酸盐含量越大，其微乳液增溶的水量越大；磺酸盐含量一定时，苯乙烯含量越小，其微乳液增溶的水量越大；正构醇质量分数为在2％～10％范围内，其微乳液增溶的水量最多；三种醇相比较，正丁醇体系的微乳区是W／O型向O／W型过渡的连续区域，正丙醇体系的O／W型微乳液区明显不同于正丁醇体系，正戊醇体系不能形成水包油型的微乳区。     

Phase‐separation mechanism and corresponding final morphologies of thermoset blends based on unsaturated polyester and low‐molar‐weight saturated polyester

The final morphology of cured blends based on unsaturated polyester, styrene, and low‐molar‐weight saturated polyester as a low profile additive (LPA) was investigated with atomic force microscopy and scanning electron microscopy. The observed structure was compared to those obtained with widely used poly(vinyl acetate) (PVAc). On the surface and in the bulk, a network of particles, ranging in size from 50 to 60 nm, was observed with saturated polyester as an LPA. The influence of the molar weight and LPA content was investigated. To determine the mechanism of formation of such a morphology, in situ experiments were carried out to elucidate the phase‐separation mechanism. Small‐angle laser light scattering and small‐angle neutron scattering experiments were performed on ternary blends containing PVAc and saturated polyester, respectively. The first stage of spinodal decomposition was observed in both cases. Within our experimental conditions, gelation froze further evolution and led to a two‐phase cocontinuous structure that imposed the final morphology characteristics. In particular, the period and amplitude of the concentration fluctuations generated during the phase separation played essential roles. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1459–1472, 2005     

Application of azodiisobutyronitrile and azobisisoheptonitrile in low‐density unsaturated polyester resin manufacturing

Low‐density unsaturated polyester resin (LDUPR) is an extended application of unsaturated polyester resin (UPR) material. In this study, azodiisobutyronitrile (AIBN) and azobisisoheptonitrile (ABVN) were presented as composite foaming agents and as initiators in LDUPR manufacturing. On the basis of the kinetics of AIBN and ABVN, their optimum half‐lives (t_1/2's) for LDUPR were both 1.0 h. In this study, the mass ratio of AIBN and ABVN was chosen at 7:3, and the preferred amount of the composite foaming agent was 2 wt % resin. They were treated at a molding temperature of 78.7 ± 1.0°C. The obtained LDUPR had an apparent density of 0.37 ± 0.01 g/cm³ and a specific compression strength of 35.58 ± 1.50 MPa·g^?1·cm^?3; it approached the highest specific compression strength value of rigid polyurethane foam (28–35 MPa g^?1 cm^?3). A dual‐initiation and dual‐foaming mechanism based on the dual‐exothermic decomposition properties of the composite foaming agent was proposed with the support of the differential scanning calorimetry and scanning electron microscopy results. In the first stage, ABVN decomposed, released bubble nuclei, and initiated UPR cross‐polymerization. The bubble nuclei spread in the resin glue and grew. In the second stage, the gas in resin glue was enriched by the AIBN decomposition. The gelation time of the resin glue was influenced by AIBN and delayed. With the curing of resin, more bubbles grew up, took shape, and were retained in the UPR matrix. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40238.     

Activity of a modified redox system for polymerization of unsaturated polyester resins

Summary: A modified redox system intended for initiation of radical polymerization of unsaturated polyester resins was investigated. The main feature of this modification was the presence of an additional accelerator—sodium formaldehyde sulfoxylate (also known as Rongalit). Rongalit acts as a reducer in hydrophilic medium. The interaction between Rongalit and the hydrophobic ingredients of the reactive mixture occur at the boundary surfaces between the different phases.The specific influence of the initiating systems components over the polymerization kinetics was estimated. The technological time needed for gelling and then—for complete hardening of the resin was determined. The end properties of the cured polyesters as well as those of their derivative glass-fibres-reinforced composites were not found to be dependent on the mode of initiation of the polymerization process.