Mechanical properties of Mg(OH)2/polypropylene composites modified by functionalized polypropylene

Modified Mg(OH)₂/polypropylene (PP) composites were prepared by the addition of functionalized polypropylene (FPP); and acrylic acid (AA) and by the formation of in situ FPP. The effects of the addition of FPP and AA and the formation of in situ FPP on the mechanical properties of Mg(OH)₂/PP composites were investigated. Experimental results indicated that the addition of Mg(OH)₂ markedly reduced the mechanical properties of PP. The extent of reduction in notch impact strength of PP was higher than that in flexural strength and tensile strength. However, tensile modulus and flexural modulus increased with increased Mg(OH)₂ content. The addition of FPP facilitated the improvement in the flexural strength and tensile strength of Mg(OH)₂/PP composites. The higher the Mg(OH)₂ content was, the more significant the effect of FPP was. The incorporation of AA resulted in further increased mechanical properties, in particular the flexural strength, tensile strength, and notch impact strength of Mg(OH)₂/PP composites containing high levels of Mg(OH)₂. It not only improved mechanical properties but also increased the flame retardance of Mg(OH)₂/PP composites. Although the mechanical properties of composites modified by the formation of in situ FPP were lower than those of composites modified by only the addition of AA in the absence of diamylperoxide, the mechanical properties did not decline with increased Mg(OH)₂ content. Moreover, the mechanical properties increased with increasing AA content. The addition of an oxidation resistant did not influence the mechanical properties of the modified Mg(OH)₂/PP composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2139–2147, 2003     

Crystallization and dynamic mechanical properties of polypropylene/polystyrene blends modified with maleic anhydride and styrene

Polypropylene (PP)/polystyrene (PS) blends modified with reactive monomers, such as maleic anhydride (MAH) and styrene (St), and in situ formed PP/PS blends were prepared by melting extrusion. The crystallization and melting behavior and the dynamic mechanical properties of the PP/PS blends, including the structure of the grafted copolymer, were investigated with differential scanning calorimetry, dynamic mechanical analysis, and Fourier transform infrared. The results indicated that the addition of MAH hardly influenced the crystallization temperature of PP in the blends, but the addition of MAH and St increased the crystallization temperature of PP in its blends. The blends showed no remarkable variety for the melting temperature, but the shapes of the melting peaks were influenced by the addition of the reactive monomers. In addition, a significant increase in the storage and loss moduli of all the modified PP/PS blends was observed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2038–2045, 2005     

Crystallization kinetics of polypropylene composites filled with nano calcium carbonate modified with maleic anhydride

The subject of this study was the crystallization behavior and thermal properties of polypropylene (PP)/maleic anhydride (MAH) modified nano calcium carbonate (nano‐CaCO₃) composites. In this study, 5 wt % nano‐CaCO₃ modified with different contents of MAH was filled into a PP matrix. X‐ray diffraction and differential scanning calorimetry were used to characterize the crystal morphology and crystallization kinetics of a series of composites. The results demonstrate that the nano‐CaCO₃ modified with MAH had an important effect on the thermal and morphological properties of the nanocomposites. The Avrami exponent of the pure PP was an integer, but those of the composites were not integers, but the crystallization rate constant decreased as the content of MAH in the nano‐CaCO₃ filler increased in isothermal crystallization. In nonisothermal crystallization, the kinetic parameter F(T) and the degree of crystallinity of pure PP were compared with those of the PP composites filled with nano‐CaCO₃. We suggest that heterogeneous nucleation existed in the PP composites and that the transformation and retention of the β‐form crystal into the α‐form crystal took place in the composite system and the β‐form crystal had a higher nucleation rate and growth process than the α‐form crystal in the PP composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of calcium carbonate on the mechanical and thermal properties of isotactic polypropylene/ethylene vinyl acetate blends

The effect of calcium carbonate (CaCO₃) on the mechanical properties (with heat treatment) and thermal properties of polypropylene and isotactic polypropylene (i‐PP)/ethylene vinyl acetate (EVA) blends was investigated. CaCO₃, in five different concentrations (3, 6, 9, 12l, and 15 wt %), was added to i‐PP/EVA (88/12) to produce ternary composites. The mechanical properties, including the yield and tensile strengths, elastic modulus, Izod impact strength for notch radii of 0.25 and 1 mm, and hardness with and without an annealing heat treatment, and the thermal properties, such as the melting point and melt‐flow index, of the composites were investigated. The annealing heat treatment was carried out at 100°C for three different holding times: 75, 100, and 150 h. On the basis of the results, attempts were made to establish a relationship between the CaCO₃ content, the annealing holding time, and the mechanical and thermal properties to obtain the best results. The tensile test results showed that the heat treatment was not effective for the ultimate tensile strength, and the yield strength and tensile strength decreased gradually as the CaCO₃ content increased. However, CaCO₃ was effective for higher elastic modulus, impact strength, and hardness values. A considerable increase in the elastic modulus was found with a 3% CaCO₃ concentration for a holding time of 100 h. The maximum impact strength for a notch radius of 1 mm was obtained with 3% CaCO₃ with annealing for a holding time of 100 h, whereas a 9% CaCO₃ concentration produced higher toughness values for a notch radius of 0.25 mm. The fracture surfaces also supported the results from the Izod impact tests. Similarly, hardness values increased with the annealing heat treatment and increasing CaCO₃ content. However, different holding times showed similar effects on the hardness values. The increased CaCO₃ content caused the melting point to increase 5°C, whereas the melt‐flow index showed a sharp decrease as the CaCO₃ content increased to 3%. Taking into consideration the mechanical and thermal properties and the annealing holding time, we recommend a CaCO₃ concentration of 3% with an annealing heat treatment for 100 h for optimum properties of such ternary composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1126–1137, 2005     

Morphology and mechanical properties of polypropylene and poly(ethylene‐co‐methyl acrylate) blends

The morphology and mechanical properties of isotactic polypropylene (iPP) and poly(ethylene‐co‐methyl acrylate) (EMA) blends were investigated. Various EMA copolymers with different methyl acrylate (MA) comonomer content were used. iPP and EMA formed immiscible blends over the composition range studied. The crystallization and melting reflected that of the individual components and the crystallinity was not greatly affected. The size of the iPP crystals was larger in the blends than those of pure iPP, indicating that EMA may have reduced the nucleation density of the iPP; however, the growth rate of the iPP crystals was found to remain constant. The tensile elongation at break was greatly increased by the presence of EMA, although the modulus remained approximately constant until the EMA composition was greater than 20%. EMA with a 9.0% MA content provided the optimum effect on the mechanical properties of the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 175–185, 2003     

Effects of calcium carbonate and its purity on crystallization and melting behavior,mechanical properties,and processability of syndiotactic polypropylene

Calcium carbonate‐filled syndiotactic poly(propylene) (CaCO₃‐filled s‐PP) was prepared in a self‐wiping, co‐rotating twin‐screw extruder. The effects of CaCO₃ of varying particle size (1.9, 2.8 and 10.5 μm), content (0–40 wt %), and type of surface modification (uncoated, stearic acid‐coated, and paraffin‐coated) on the crystallization and melting behavior, mechanical properties, and processability of CaCO₃‐filled s‐PP were investigated. Non‐isothermal crystallization studies indicate that CaCO₃ acts as a good nucleating agent for s‐PP. The nucleating efficiency of CaCO₃ for s‐PP was found to depend strongly on its purity, type of surface treatment, and average particle size. Tensile strength was found to decrease, while Young's modulus increased, with increasing CaCO₃ content. Both types of surface treatment on CaCO₃ particles reduced tensile strength and Young's modulus, but improved impact resistance. Scanning electron microscopy (SEM) observations of the fracture surfaces for selected CaCO₃‐filled s‐PP samples revealed an improvement in CaCO₃ dispersion as a result of surface treatment. Finally, steady‐state shear viscosity of CaCO₃‐filled s‐PP was found to increase with increasing CaCO₃ content and decreasing particle size. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 201–212, 2004     

Effect of oxidized polypropylene as a new compatibilizer on the water absorption and mechanical properties of wood flour–polypropylene composites

The effect of oxidized polypropylene (OPP) as new compatibilizer on the water absorption and mechanical properties of wood flour–polypropylene (PP) composites were studied and compared with maleic anhydride grafted polypropylene (MAPP). The oxidation of PP was performed in the molten state in the presence of air. Wood flour, PP, and the compatibilizers (OPP and MAPP) were mixed in an internal mixer at temperature of 190°C. The amorphous composites removed from the mixer were then pressed into plates that had a nominal thickness of 2 mm and nominal dimensions of 15 × 15 cm² with a laboratory hydraulic hot press at 190°C. Physical and mechanical tests showed that the wood flour–PP composites with OPP exhibited higher flexural and impact properties but lower water absorption than MAPP. All of the composites with 2% compatibilizers (OPP and MAPP) gave higher flexural and impact properties and lower water absorption compared to those with 4% compatibilizers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and thermal properties of talc and calcium carbonate filled polypropylene hybrid composites

The main aim of this work was to study and compare the mechanical and thermal properties of hybrid polypropylene (PP) composites and single‐filler PP composites. With two main types of mineral fillers—calcium carbonate (CaCO₃) and talc—PP composites of different filler weight ratios (talc/CaCO₃) were compounded with a twin‐screw extruder and then injection‐molded into dumbbell specimens with an injection‐molding machine. Tensile, flexural, and impact tests were performed to determine and compare the mechanical properties of the hybrid and single‐filler PP composites. A synergistic hybridization effect was successfully achieved; the flexural strength and impact strength were highest among the hybrids when the PP/talc/CaCO₃ weight ratio was 70:15:15. The nucleating ability of the fillers and its effects on the mechanical properties were also studied with differential scanning calorimetry. Because of the influence of talc as the main nucleating agent, the hybrid fillers showed significant improvements in terms of the nucleating ability, and this contributed to the increase in or retention of the mechanical properties of the hybrid composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3327–3336, 2004     

Effect of the mixing sequence on the morphology and properties of a polypropylene/polydimethylsiloxane/nano‐SiO2 ternary composite

Ternary composites of polypropylene (PP), polydimethylsiloxane (PDMS) elastomer, and nano‐SiO₂, prepared with three different mixing sequences, were studied for dispersion morphology and its effect on the crystallization of PP and the mechanical properties. The mixing sequence produced a significant effect on the dispersion morphology and, thereby, on the mechanical properties of the composites. A two‐step mixing sequence, in which nano‐SiO₂ was added in the second step to the PP/PDMS binary system, produced a significant encapsulation of nano‐SiO₂ by PDMS, and this, in turn, resulted in the poor modulus and impact strength of the composite. A one‐step mixing sequence of all three components produced a separated dispersion of PDMS and nano‐SiO₂ phases in the PP matrix with the occurrence of a fine band of nano‐SiO₂ particles at the boundaries of the PDMS domains and the presence of some nano‐SiO₂ filler particles inside the PDMS domains. This one‐step mixing sequence produced an improvement in the tensile modulus but a decrease in the impact strength with increasing nano‐SiO₂ content. In the third sequence of mixing, which involved a two‐step mixing sequence through the addition of PDMS in the second step to the previously prepared PP/nano‐SiO₂ binary system, the morphology of the dispersion showed separately dispersed PDMS and nano‐SiO₂ phases with a loose network of nano‐SiO₂ particles surrounding the PDMS domains. This latter series of ternary composites had the highest impact strength and exhibited high shear deformation under tensile and impact conditions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization behavior and mechanical properties of polypropylene copolymer by in situ copolymerization with a nucleating agent and/or nano‐calcium carbonate

The crystallization behavior of polypropylene (PP) copolymer obtained by in situ reactor copolymerization with or without a nucleating agent and/or nano‐CaCO₃ particles was investigated both by thermal analysis and by polarized light microscopy. The Avrami model is successfully used to describe the crystallization kinetics of the studied copolymer. The results of the investigation show that a dramatic decrease of the half‐time of crystallization t_1/2, as well as a significant increase of the overall crystallization rate, are observed in the presence of the nucleating agent. These effects are further promoted in the presence of the nano‐CaCO₃ particles. The incorporation of the nucleating agent and nano‐CaCO₃ particles into PP copolymer remarkably improved the mechanical properties and heat distortion temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 431–438, 2004     

Effects of rosin‐type cocrystal nucleating agents on the crystallization process and the properties of polypropylene

A new kind of rosin‐type nucleating agent for polypropylene (PP), the cocrystal of dehydroabietic acid, potassium dehydroabietate, and sodium dehydroabietate, was prepared, and the effects of the nucleating agents on the mechanical and crystallization properties of PP were also studied. The results of differential scanning calorimetry and X‐ray diffraction proved that the cocrystal of dehydroabietic acid and compound alkali dehydroabietate was formed rather than a simple blend of dehydroabietic acid and single alkali dehydroabietate. When it was added to PP, the size of the PP spherulite decreased; the mechanical properties, crystallization temperature, and transparency of PP were substantially improved. Thus, the cocrystal of dehydroabietic acid, potassium dehydroabietate, and sodium dehydroabietate acted as a more effective nucleating agent for PP. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2137–2141, 2003     

Thermal and mechanical properties of a polypropylene nanocomposite

An experimental polypropylene (PP) nanocomposite, containing approximately 4 wt % of an organophilic montmorillonite clay, was prepared and characterized, and its properties were compared with those of talc‐filled (20–40 wt %) compositions. Weight reduction, with maintained or even improved flexural and tensile moduli, especially at temperatures up to 70°C, was a major driving force behind this work. By a comparison with the analytical data from a nylon 6 (PA‐6) nanocomposite, it was found that the PP nanocomposite contained well‐dispersed, intercalated clay particles; however, X‐ray diffraction, transmission electron microscopy, dynamic mechanical analysis, and permeability measurements confirmed that exfoliation of the clay in PP was largely absent. The increased glass‐transition temperature (T_g) of a PA‐6 nanocomposite, which possessed fully exfoliated particles, indicated the molecular character of the matrix–particle interaction, whereas the PP nanocomposite exhibited simple matrix–filler interactions with no increase in T_g. The PP nanocomposite exhibited a weight reduction of approximately 12% in comparison with the 20% talc‐filled PP, while maintaining comparable stiffness. Undoubtedly, considerable advantages may be available if a fully exfoliated PP nanocomposite is fabricated; however, with the materials available, a combination of talc, or alternative reinforcements, and nanocomposite filler particles may provide optimum performance. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1639–1647, 2003     

Correlation of the material properties of calcium carbonate filled polypropylene with the filler surface energies

The physical and mechanical properties of polypropylene (PP) were measured and compared with those of PP composites filled with calcium carbonate modified with sodium polyacrylate, stearic acid, or both. The variations in the mechanical properties showed a high degree of correlation with the surface energies of the fillers, as determined by inverse gas chromatography. The results confirmed the usefulness of inverse gas chromatography for characterizing the compatibility of polymer–filler combinations. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1951–1955, 2003     

Effect of the delignification of wood fibers on the mechanical properties of wood fiber–polypropylene composites

The effect of the delignification of hornbeam fibers on the mechanical properties of wood fiber–polypropylene (PP) composites was studied. Original fibers and delignified fibers at three levels of delignification were mixed with PP at a weight ratio of 40:60 in an internal mixer. Maleic anhydride (0.5 wt %) as the coupling agent and dicumyl peroxide (0.1 wt %) as the initiator were applied. The produced composites were then hot‐pressed, and specimens for physical and mechanical testing were prepared. The results of the properties of the composite materials indicate that delignified fibers showed better performance in the enhancement of tensile strength and tensile modulus, whereas the hardness of the composites was unaffected by delignification. Delignified fibers also exhibited better water absorption resistance. Notched impact strength was higher for delignified fiber composites, but it was reduced at higher delignification levels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4759–4763, 2006     

Effect of the elastomer type on the microstructure and mechanical properties of polypropylene

In this study, the effects of the elastomer type—ethylene–propylene–diene monomer (EPDM), three kinds of ethylene vinyl acetate (EVA 9, EVA 18, and EVA 28, where the number is the vinyl acetate concentration), and styrene–butadiene–styrene—and content on the microstructure and mechanical and thermal properties of isotactic polypropylene (i‐PP) blends were investigated. Five different elastomer concentrations (3, 6, 9, 12, and 15 wt %) were added to i‐PP to produce polypropylene/elastomer blends. The yield and tensile strengths, elastic modulus, impact strength, hardness, melt flow index (MFI), and structural properties of the blends were investigated. The tensile and yield strengths, elastic modulus, and hardness decreased gradually, whereas the impact strength and MFI increased as the elastomer content increased. As a result, with respect to the impact strength, the most effective elastomers were EPDM with 15 wt % and EVA 28 with 15 wt % for higher impact strength values. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1445–1450, 2005     

Comparison of the mechanical properties and interfacial interactions between talc,kaolin, and calcium carbonate filled polypropylene composites

Three types of mineral fillers—talc, calcium carbonate (CaCO₃), and kaolin (10–40 wt % filler loadings)—were compounded with polypropylene (PP) with a twin‐screw extruder. The composites were injection‐molded, and the effects of the filler loading on the mechanical, flow, and thermal properties for the three different types of filled composites were investigated. The aim was to compare their properties and to deduce prospective filler combinations that would yield hybrid PP composites in following studies. The results showed that in most cases, the strength and stiffness of the talc‐filled PP composites was significantly higher than those of the CaCO₃‐ and kaolin‐filled PP composites. However, CaCO₃, being a nonreactive filler, increased the toughness of PP. The kaolin‐filled PP composites also showed some improvement in terms of strength and stiffness, although the increases in these properties were not as significant as those of the talc‐filled PP composites. The effects of interfacial interactions between the fillers and PP on the mechanical properties were also evaluated with semiempirical equations. The nucleating ability of all three fillers was studied with differential scanning calorimetry, and the strongest nucleating agent of the three was talc, followed by CaCO₃ and kaolin. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3315–3326, 2004     

Improving the mechanical properties of polypropylene via melt vibration

The effect of melt vibration on the mechanical properties of polypropylene prepared by low-frequency vibration-assisted injection molding (VAIM) has been investigated. With the application of melt vibration technology, the mechanical properties of polypropylene are improved. The yield strength increases with the increment of the vibration frequency, and a peak stands at a special frequency for VAIM; the elongation at break decreases first and then increases with increasing vibration frequency, and a valley stands at a special frequency. The tensile properties increase sharply at an enlarged vibration pressure amplitude with sharply decreased elongation at break. The Young's modulus and impact strength also increase with the vibration frequency and pressure vibration amplitude. When it is prepared at 59.4 MPa and 0.7 Hz, the maximal yield strength is approximately 40 MPa versus 33.7 MPa for a conventional sample; an 18.7% increase in the tensile strength is produced. Self-reinforcing and self-toughening polypropylene molded parts have been found to be prepared at a high vibration frequency or at a large pressure vibration amplitude. Scanning electron micrographs have shown that, in the vibration field, the enhancement of the mechanical properties is attributable to more pronounced spherulite orientation and increased crystallinity in comparison with conventional injection moldings. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and properties of isotactic polypropylene modified with hydrocarbon resin MBG273. I. Binary blends

We investigated a system formed of isotactic polypropylene (iPP) and hydrogenated hydrocarbon resin MBG273 (up to 30 wt % resin) to study the influence of the composition on the morphology, structure, and properties of its blends and derived films. All the blends, after the mixing of the components in the melt and cooling at room temperature, were formed by a crystalline phase of iPP and by one homogeneous phase formed by amorphous iPP and the MBG273 resin. The presence of MBG273 did not influence the crystalline structure of iPP, which remained, for every blend, α‐monoclinic, but it reduced the crystallization temperature and nucleation density of iPP. Differential scanning calorimetry and dynamic mechanical thermal analysis showed an increase in the glass‐transition temperature with the resin content, confirming the formation of one amorphous phase. Tensile property analysis indicated an increase in Young's modulus and a decrease in the elongation at break of films as a function of the resin content in the blends. The water vapor permeability and tensile mechanical properties were related to an increase in the glass transition with the addition of MBG273. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3454–3465, 2004     

Effect of corn‐zein coating on the mechanical properties of polypropylene packaging films

In this study, a novel film structure of corn zein coated on polypropylene (PP) synthetic films for food packaging applications was developed, and the mechanical properties of the resulting coated film, as affected by the coating formulation, were investigated. Composite structures of PP films coated with corn zein were obtained through a simple solvent casting method. Different amounts of corn zein (5 and 15%) were dissolved in 70 and 95% aqueous ethanol solution at 50°C. Solutions of corn zein plasticized with poly(ethylene glycol) and glycerol (GLY) at various levels (20 and 50%) were applied on corona‐discharge‐treated PP. A statistical analysis based on full factorial design was performed to examine the influence of the coating formulation on the final properties of the corn‐zein‐coated PP films. A significant (p < 0.05) improvement in the coated film's mechanical properties was observed compared to those of the uncoated PP. The effect of the plasticization of the coating solutions was also quite significant. In general, GLY provided better improvements in the mechanical properties of the corn‐zein‐coated PP films. The statistical analysis of the results showed that the corn‐zein and plasticizer concentrations and plasticizer type used in the coating formulations were more effective parameters and had significant effects on the mechanical behavior of the coated PP films. In conclusion, corn‐zein coatings could have potential as alternatives to conventional synthetic polymers used in composite multilayer structures for food packaging applications. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of the zeolite type on the mechanical–thermal properties and volatile organic compound emissions of natural‐flour‐filled polypropylene hybrid composites

The physicomechanical properties, thermal properties, odor, and volatile organic compound (VOC) emissions of natural‐flour‐filled polypropylene (PP) composites were investigated as a function of the zeolite type and content. The surface area and pore structure of the natural and synthetic zeolites were determined by surface area analysis and scanning electron microscopy, respectively. With increasing natural and synthetic zeolite content, the tensile and flexural strengths of the hybrid composites were not significantly changed, whereas the water absorption was slightly increased. The thermal stability and degradation temperature of the hybrid composites were slightly increased with increasing natural and synthetic zeolite content. At natural and synthetic zeolite contents of 3%, the various odors and VOC emissions of the polypropylene/rice husk flour and polypropylene/wood flour hybrid composites were significantly reduced because of the absorption of the odor and VOC materials in the pore structures of the natural and synthetic zeolites. These results suggest that the addition of natural and synthetic zeolites to natural‐flour‐filled thermoplastic polymer composites is an effective method of reducing their odor and VOC emissions without any degradation of their mechanical and thermal properties. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008