Silicon‐containing anionic water‐borne polyurethane with covalently bonded reactive dye

A silicon‐containing water‐borne polyurethane (PU) polymer with hydroxyl side groups was synthesized that was stable in basic conditions and also capable of reacting with a reactive dye to form a covalently bonded dye molecule. The silicon‐containing anionic water‐borne PU prepolymer was synthesized from H₁₂‐4,4′‐diphenylmethane diisocyanate (H₁₂‐MDI), polytetramethylene glycol, polydimethylsiloxane (PDMS), 2,2′‐bis(hydroxymethyl), propionic acid (anionic centers), and triethyleneamine using the prepolymer mixing method. Water was then added to emulsify and disperse the resin to form an anionic water‐borne PU prepolymer. N‐(2‐Hydroxyethyl ethylene diamine) (HEDA) was used to extend the prepolymer to form a water‐borne PU polymer with a side chain of hydroxyl groups, which can further react with the reactive dye to form a dyed PU. The reactive dye of chlorosulfuric acid esters of sulfatoethyl sulfones can react with the water‐borne PU polymer. Behaviors of alkali resistance and dyeing properties were observed. In consideration of thermal properties, the dye‐grafted PU polymers exhibited lower glass‐transition temperatures for soft segments and hard segments than those without dye. Concerning mechanical properties, it was found that the modulus and the strength of the dyed PU polymers decreased with grafting of the dye molecule, but elongation at break was increased. The alkali resistance increased with PDMS content. For dye‐uptake properties, the percentage of dye grafting was over 90%. Also, the dye‐grafted PU exhibited a lower percentage of dye migration than that of polymers with ethylene diamine instead of HEDA as a chain extender, and showed greater colorfastness to light. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2045–2052, 2003     

Synthesis of anionic water‐borne polyurethane with the covalent bond of a reactive dye

We successfully synthesized an anionic water‐borne polyurethane (PU) capable of reacting with a reactive dye to form a covalent bond with the dye molecule. The anionic water‐borne PU was synthesized and grafted with the reactive dye to form a dyed PU. First, the PU prepolymer was synthesized from 4,4′‐methylene bis(isocyanatocyclohexane), poly(tetramethylene glycol), 2,2′‐bis(hydroxymethyl) propionic acid (as an anionic center), and triethyleneamide (as a neutralizer). Then, pure water was added to emulsify and disperse the prepolymer to form an anionic water‐borne PU prepolymer. Finally, the extender N‐(2‐hydroxyethyl) ethylene diamine was used to extend the anionic water‐borne prepolymer to form a PU polymer with hydroxyl groups that could further react with the reactive dye molecule. With respect to the heating properties, the dyed PU polymers exhibited higher glass‐transition temperatures of the hard segment than those without dye molecules. However, neither the glass‐transition temperature of the soft segment nor the melting temperature of the soft segment varied in the presence of dye molecules, but they were changed with various chain lengths of the soft segment. As for the mechanical properties, the modulus and strength of the dyed PU polymers decreased because of the bulkiness of their dye molecules, but the breaking elongation increased. Moreover, the inherent viscosity decreased in the presence of the dye molecules. As for the dyeing properties, the percentage of dye grafting was greater than 90%. The dye‐grafted PU exhibited a lower percentage of migration than PU extended with ethylene diamine (without hydroxy groups) and also showed a higher grade of colorfastness to light. © 2002 John Wiley & Sons, Inc. J Appl Polym Sci 84: 797–805, 2002; DOI 10.1002/app.10336     

Synthesis and characterization of inherently flame‐retardant and anti‐dripping thermoplastic poly(imides‐urethane)s

A series of thermoplastic poly(imide‐urethane)s (TPIUs), based on 4,4′‐diphenylmethane diisocyanate (MDI) and pyromellitic anhydride (PMDA) as hard segments and poly(tetrahydrofuran) (PTMG) as soft segments, has been prepared by a two‐step polymerization process. The objective of this study is to prepare a type of intrinsically flame‐retardant polyurethane by incorporating PMDA as a flame retardant in the main chains. The thermal behavior and flame retardancies of the TPIUs have been characterized by thermal gravimetric (TG) analysis and limiting oxygen index (LOI), UL‐94 vertical burning, cone calorimeter tests. The results indicate that the TPIUs display outstanding performance. The temperature at 5% mass loss (T_5%) and LOI value increase with the hard‐segment contents, while the total heat released (THR) and peak heat release rate (p‐HRR) show the opposite trend. Furthermore, the T_5% of TPIU211 (molar ratio: MDI : PTMG : PMDA = 2 : 1 : 1) is 33.2°C higher than that of the conventional thermoplastic polyurethane TPU211 (molar ratio: MDI : PTMG : 1,4‐butanediol = 2 : 1 : 1), and the THR and p‐HRR of TPIU211 are 14.62% and 64.02% lower than the respective parameters of TPU211. In addition, UL‐94 vertical burning tests show that the TPIUs exhibit excellent antidripping effects. The ultimate tensile strengths of the TPIUs reached 23.1?37.6 MPa with increasing hard segment contents, which meets the requirement of mechanical properties with regard to practical use. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40801.     

A novel synthesis of reactive nano‐clay polyurethane and its physical and dyeing properties

This study is about polyurea prepolymer, which was synthesized from the extender (N‐(2‐hydroxyethyl) ethylene diamine, HEDA or ethylene diamine, EDA) with 4,4′‐diphenylmethane diisocyanate (MDI), as an intercalative agent to intercalate the organic modified montmorillonite clay. Then, it is further reacted with the polyurethane prepolymer, which is polymerized from the polytetramethylene glycol (PTMG) and MDI, to proceed the intercalative polymerization to form a polyurethane/clay nanocomposite polymer. The experimental parameters contain the use of polyurea intercalative prepolymer extender and also the contents of organo‐clay in the prepolymer etc. We expect to get better mechanical property and also to improve the dyeing properties of nano‐clay polyurethane. The polyurethane/clay polymer is synthesized using two‐step method: synthesizing the polyurethane prepolymer from PTMG and MDI and then extended with the polyurea prepolymer modified with the organo‐clay. Because the extender HEDA contains side chain of hydroxyl groups, the modified PU can further react with the reactive dye. From the experimental results of the fine structure (X‐ray and FT‐IR) and mechanical analysis, it is found that the intercalation is successfully achieved. Thedistance of interlayer spacing is manifestly enlarged. The mechanical properties are significantly improved as the content of organo‐clay is increased. Besides, although thedye up‐take is decreased with the increasing content oforgano‐clay, but the water‐resistant fastness is improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and application to cellulose of reactive dye precursor of anti‐bacterial N‐halamine

To achieve textile dyeing and functional finishing in one process, a bleach‐resistant reactive dye precursor to anti‐bacterial N‐halamine was synthesised by reacting a type of dichlorotriazine reactive dye with 4‐amino‐2,2,6,6‐tetramethylpiperidine. The synthesised compound, which can be transformed to an N‐halamine molecule by exposure to dilute bleach solution, was used to dye cotton fabrics. After exposure to a dilute sodium hypochlorite solution, dyed cotton fabrics showed excellent anti‐bacterial properties against Staphylococcus aureus and Escherichia coli O157:H7, facilitating a ca. 6‐log reduction in bacteria within a short period of contact. Compared with the dichlorotriazine reactive dye, the reactive dye precursor demonstrated comparable dyeing properties including exhaustion and fixation values. No differences in rub fastness, wash fastness or bleach fastness were detected between fabrics dyed with, respectively, dichlorotriazine reactive dye and the reactive dye precursor to N‐halamine.     

Modified polyurethane with improvement of acid dye dyeability

This article concerns the modification of polyurethane using polyamide 6,6 prepolymer to improve the dyeability properties of the polyurethane copolymer with acid dye. First, the carboxyl‐terminated polyamide 6,6 prepolymer was synthesized from adipic acid and 1,6‐diaminohexane. The isocyanate‐terminated polyurethane prepolymer was also synthesized from polytetramethylene glycol and 4,4′‐diphenylmethane diisocyanate in N,N‐dimethylformamide. The polyurethane prepolymer was then extended with a mixture of 1,4‐butanediol and the polyamide 6,6 prepolymer (molar ratios of 1,4‐butanediol to prepolymer being 100%, 75%, 50%, and 25%, respectively). Finally, the poly(urethane–amide) copolymers were dyed with acid dyes. The chemical, physical, and the dyeing properties of the poly(urethane–amide) coploymers are discussed. From the experimental results, it is found that the inherent viscosity of poly(urethane–amide) coploymers is increased with the increasing amount of polyamide content. The structure is proven by infrared spectra, which exhibits the absorption peaks of urethane and amide groups as we expected. From the differential scanning calorimetry measurements, it is found that the poly(urethane–amide) coploymers have two‐phase structures and good phase separation. There are four transition temperatures (T_gs, T_gh, T_ms, and T_mh), but only those copolymers in PTMG 2,000 series possess T_ms. Moreover, the T_gs is found to change with the length of soft segment, and the T_gh is increased with the increasing amount of polyamide content. Also, the dyed copolymers exhibit higher T_gh than those without dyeing of dye molecule, but the T_gs is not obviously changed. For mechanical properties, it is indicated that both the modulus and the strength of the coploymers are higher than those of unmodified polyurethane, but they are lowered after being dyed with dye molecule due to further separation of intermolecular distance of the dyed polyurethanes. For dye uptake in dyeing properties, it is found to increase with increasing amount of polyamide content. For dye fastness, the dyed copolymers exhibit higher grade of water fastness than that of unmodified polyurethane. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1397–1404, 2003     

In Situ synthesis of multiblock copolymers of poly(ϵ‐caprolactone) with different poly(ether diols) based polyurethane by reactive extrusion

Polyurethanes with multiblock copolymers of poly(?‐caprolactone) (PCL) and poly(tetramethylene oxide) glycol (PTMG) or poly(ethylene glycol) (PEG) as a soft segment were synthesized in situ via reactive extrusion from ?‐caprolactone (CL) and 4,4′‐diphenylmethane diisocyanate (MDI). The titanium alkoxide mixture generated from an ester‐exchange reaction between titanium propoxide [Ti(OPr)₄], and excessive PTMG or PEG was used as an initiator and catalyst. Compared to the reported fabrication of polycaprolactone‐based polyurethane (PCLU), the in situ reactive extrusion preparation not only explored a new rapid route for the fabrication of PCLU but also offered a simplified, controllable approach for the production of PCLU in a successive mass scale. A series of PTMG–PCLUs and PEG–PCLUs with different PCL block‐average degrees of polymerization (DP_n's) were prepared by only an adjustment of the relative concentration of CL in the reaction system, with a certain constant molar ratio of MDI to titanium alkoxide. ¹H‐NMR, gel permeation chromatography, and differential scanning calorimetry results indicate that all of the CL monomers were converted in the polymerization, and the molecular weight of the copolymers was about 8 × 10⁴ g/mol with a polydispersity index of approximate 2.4. With an increase in the PCL block‐average DP_n in PTMG–PCLU from 25 to 40, the tensile strength increased from 16.5 to 22.7 MPa, and the melting point increased from 46.1 to 49.5°C. It was also verified by PEG–PCLU prepared with organic Ti of lowered content in the initiator mixture that the mechanical properties could be greatly affected and dropped with decreasing content of organic Ti in the initiator mixture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Poly(urea-urethane) polymers with multi-functional properties

Polyurea-urethanes with multifunctional properties were synthesized by reacting 4,4′-diphenylmethane disocyanate (MDI) with a two diol mixture of polytetramethylene glycol (PTMG (1000, 2000) and biocidal quaternary ammonium monomer ((N-benzyl-N-dodecyl-N-bis2-hydroxyethyl) ammonium chloride (BDAC)), and extended with N-(2-hydroxyethyl) ethylene diamine (HEDA) to form PU polymers. The PU polymer was then grafted with a disperse dye via a coupling agent of epichlorohydrin to form a dye grafted polyurethane with biocidal and covalent bond dyeing properties. In consideration of the mechanical properties, it is found that both the modulus and the strength of the dye grafted PU polymer films are lower than those of pure PU polymers due to the bulkiness of their dye molecules. For thermal properties, the dye grafted PU polymers exhibit higher T_gh than those without dye molecules. However,neither the T_gs nor the T_ms vary in the presence of BDAC or dye molecules, but they are changed with various chain lengths of the soft segment. For dyeing properties, the effective dyeing efficiency of dye grafted PU is over 85%. Moreover, the dye grafted PU polymers exhibit lower dye migration (M_p%) than those of simple mixtures of PU and dyestuff, and they show a higher grade of color fastness when exposed to light. In the shake method of antibacterial testing, the modified PU polymers exhibit a long lasting biocidal activity.     

Comparison of properties of thermoplastic polyurethane elastomers with two different soft segments

Two series of thermoplastic polyurethane elastomers [poly(propylene glycol) (PPG) based PP samples and poly(oxytetramethylene)glycol (PTMG) based PT samples] were synthesized from isophorone diisocyanate (IPDI)/1,4-butanediol (BD)/PPG and IPDI/BD/PTMG. The IPDI/BD based hard segments contents of polyurethane prepared in this study were 40–73 wt %. These polyurethane elastomers had a constant soft segment molecular weight (average M_n, 2000) but a variable hard segment block length (n, 3.5–17.5; average M_n, 1318–5544). Studies were made on the effects of the hard segment content on the dynamic mechanical thermal properties and elastic behaviors of polyurethane elastomers. These properties of PPG based PP and PTMG based PT samples were compared. As the hard segment contents of PP and PT samples increased, dynamic tensile modulus and α-type glass transition temperature (T_g) increased; however, the β-type T_g decreased. The permanent set (%) increased with increasing hard segment content and successive maximum elongation. The permanent set of the PT sample was lower than that of the PP sample at the same hard segment content. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1349–1355, 1998     

Investigation of alkaline hydrolysis of phthalimide‐based azo dye and its application to after‐treatment optimisation for high‐fastness dyeing of polyesters

4‐Amino‐N‐methylphthalimide was prepared from phthalimide for use as a diazo component and was coupled with N,N‐Diethylaniline to produce a phthalimide‐derived monoazo disperse dye. The pseudo first‐order kinetics were confirmed by analyzing the dye hydrolysis under alkaline conditions using high performance liquid chromatography, and the optimal dyeing pH and alkali‐clearing conditions were proposed. The synthesised phthalimidyl disperse dyes exhibited excellent colour fastness with a mild alkaline after‐treatment instead of reduction clearing which results in a high biological oxygen demand and pH in conventional disperse dyeing wastewater.     

Differential scanning calorimetry analysis of silicon‐containing and phosphorus‐containing segmented polyurethane. I—Thermal behaviors and morphology

This article investigated thermal transition and morphology utilizing differential scanning calorimetry (DSC), which was performed on silicon‐containing and phosphorus‐containing segmented polyurethane (Si‐PU and P‐PU). The hard segments of those Si‐PU and P‐PU polymers investigated consisted of 4,4′‐diphenylmethane diisocyanate (MDI) and diphenylsilanediol (DSiD), MDI, and methylphosponic (MPA), respectively. The soft segment of those polymers comprised polytetramethylene ether glycol, with an average molecular weight of 1000 or 2000 (PTMG 1000 and PTMG 2000, respectively). Several thermal transitions appeared for on the Si‐PU and P‐PU polymers, reflecting both the soft‐segment and hard‐segment phases. The Si‐PU and P‐PU polymers with a lower hard‐segment content exhibited a high degree of phase separating as indicated by the constancy of both the soft‐segment glass transition temperature (T_gs) and the breadth of transition zone (ΔB). The polymers in which PTMG 2000 was used as the soft segment generally exhibited a crystalline melting endotherm about 10°C, while crystallization usually disappeared upon melt quenching. The hard segments of the Si‐PU and P‐PU polymers displayed multiple endotherms. The first endotherm was related to a short‐range ordering of the hard segment domain (Region I), and the second endotherm was ascribed to a long‐range ordering of the domain (Region II). The wide‐angle X‐ray demonstrated that the structure in Region I and Region II was almost completely amorphous. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3489–3501, 2001     

Synthesis and characterization of poly[(butylene succinate)‐co‐(butylene terephthalate)]‐b‐poly(tetramethylene glycol) segmented block copolymer

Polyester‐polyether segmented block copolymers of poly[(butylene succinate)‐co‐poly(butylene terephthalate)] (PBS–PBT) and poly(tetramethylene glycol) (PTMG) (M_n = 2000) with various compositions were synthesized. PBT content in the PBS was adjusted to ca. 5 mol %. Their thermal and mechanical properties were investigated. In the case of copolymer, the melting point of the PBS–PBT control was 107.8°C, and the melting point of the copolymer containing 70 wt % of PTMG was 70.1°C. Crystallinity of soft segment was 5 ∼ 17%, and that of hard segment was 42 ∼ 59%. The breaking stress of the PBS–PTMG control was 47 MPa but it decreased with increasing PTMG content. In the case of copolymer containing 70 wt % of PTMG, breaking stress was 36 MPa. Contrary to the decreasing breaking stress, breaking strain increased from 300% for PBS–PBT control to 900% for a copolymer containing 70 wt % of PTMG. The shape recovery ratios of the copolymer containing 70 wt % PTMG were almost twice of those of copolymers containing 40 wt % PTMG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2067–2075, 2001     

Preparation and properties of segmented thermoplastic polyurethane elastomers with two different soft segments

Thermoplastic polyurethane elastomers were prepared from 4,4‐diphenylmethane diisocyanate (MDI)/1,4‐butanediol (BD)/poly(propylene glycol) (PPG) and MDI/BD/poly(oxytetramethylene glycol) (PTMG). The MDI/BD‐based hard‐segment content of polyurethane prepared in this study was of 39–65 wt %. These polyurethane elastomers had a constant soft‐segment molecular weight (M_n , 2000), but a variable hard‐segment block length (n, 3.0–10.1; M_n , 1020–3434). The effects of the hard‐segment content on the thermal properties and elastic behavior were investigated. These properties of the PPG‐based MPP samples and the PTMG‐based MPT samples were compared. The polyurethane prepared in this study had a hard‐segment crystalline melting temperature in the range of 185.5–236.5°C. With increasing hard‐segment content, the dynamic storage modulus and glass transition temperature increased in both the MPP and MPT samples. The permanent set (%) increased with increasing hard‐segment content and successive maximum elongation. The permanent set (%) of the MPP samples was higher than that of MPT samples at the same hard‐segment content. The value of K (area of the hydrogen‐bonded carbonyl group/area of the free carbonyl group) increased with increasing hard‐segment content in both the MPP and MPT samples, and the K value of the MPT samples was higher than that of the MPP samples at the same hard‐segment content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 345–352, 1999     

Improved mechanical properties of shape‐memory polyurethane block copolymers through the control of the soft‐segment arrangement

High‐performance shape‐memory polyurethane block copolymers, prepared with two types of poly(tetramethylene glycol) (PTMG) used as soft segments, were investigated for their mechanical properties. Copolymers with a random or block soft‐segment arrangement had higher stresses at break and elongations at break than those with only one kind of PTMG. Random copolymers with fewer interchain interactions showed higher elongation than block copolymers. All the copolymers had shape‐recovery ratios higher than 80%. In dynamic mechanical testing, the glass‐transition behavior clearly depended on the soft‐segment arrangement: random copolymers had only one glass‐transition peak, whereas block copolymers showed two separate glass‐transition peaks. Overall, the control of the soft‐segment arrangement plays a vital role in the development of high‐performance shape‐memory polyurethane. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2410–2415, 2004     

Synthesis and application of hyperbranched poly(urethane‐urea) finishing agent with amino groups

The isocyanate‐terminated linear polyurethane prepolymer (LPPU) was successfully synthesized via step‐by‐step polymerization, with isophorone disocyanate (IPDI) and polytetramethylene ether glycol (PTMG, M_n = 2000 g/mol) used as raw materials, dibutyltin dilaurate (DBTDL) as the catalyst, 1,4‐butanediol (BDO) as the chain extender and anhydrous ethanol (EtOH) as the blocking agent. Then the hyperbranched poly (urethane‐urea) (HBPU) containing amino groups was synthesized by grafting LPPU on amino‐terminated hyperbranched polymers (NH₂‐HBP). The molecular structure of LPPU and HBPU were characterized by means of FT‐IR and ¹H‐NMR. It was founded that LPPU and HBPU were successfully synthesized as anticipated. The thermal stability and crystalline morphology of LPPU and HBPU were characterized and analyzed by TG and XRD. Additionally, it was also found that, after addition of 10% HBPU, the water absorption rate, water vapor transmission rate, and water vapor permeability increased markedly by 162.02%, 400.00%, 260.00%, respectively. The tensile strength of membrane decreased by 24.57% and the elongation at break increased by 26.92%. Compared with the leather finished by commercial PU finishing agent, the leather finished by HBPU presented better properties. The water vapor permeability of the leather finished by increased by 13.0%, and the dry‐ and wet‐rub resistances and the physical and mechanical performances were excellent. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44139.     

Chemical Processes During Energy‐Saving Preparation of Lightweight Ceramics

Lightweight glass‐ceramic material similar to foam glass was obtained at 700°C–800°C directly from alkali‐activated silica clay and zeolitized tuff without preliminary glass preparation. It was characterized by low bulk density of 100–250 kg/m³ and high pore size homogeneity. Chemical processes occurring in alkali‐activated silica clay and zeolitized tuff were studied using X‐ray diffraction, thermal gravimetry, IR‐spectroscopy, and scanning electron microscopy. Pore formation in both compositions is caused by dehydration of hydrated sodium polysilicates (Na₂O·mSiO₂·nH₂O), formed during alkali activation. Additional pore‐forming gas source in alkali‐activated zeolitized tuff is trona, Na₃(CO₃)(HCO₃)·2H₂O, formed during interaction between unbound NaOH and CO₂ and H₂O from air. Influence of mechanical activation of raw materials on chemical processes occurring in alkaline compositions was also studied.     

Effects of TDI and FA‐703 on physico‐mechanical properties of polyurethane dispersion

A series of water dispersion polyurethanes dispersions (PUDs) were prepared by polyaddition reaction using isophorone diisocyanate (IPDI), toluene diisocyanate (TDI), poly(oxytetramethylene) glycol (PTMG), dimethylol propionic acid (DMPA), and triol (trade name FA‐703). Various formulations were designed to investigate the effects of process variables such as TDI and FA‐703 on the physico‐mechanical properties of PUD. IR spectroscopy was used to check the end of polymerization reaction and characterization of polymer. Evolution of the particle size distribution, contact angle, T_g, molecular weight, viscosity, and mechanical properties of the emulsion‐cast films were significantly affected by variable content of TDI and FA‐703. Average particle size of the prepared polyurethane emulsions and contact angle decrease with increase of content of FA‐703 and TDI. Molecular weight, T_g, tensile strength, tear strength, hardness, viscosity and elongation at break increase with increase of content of FA‐703 and TDI. The increase of molecular weight, tensile strength, tear strength and elongation at break properties are interpreted in terms of increasing hard segments, chain flexibility, and phase separation in high content of FA‐703 and TDI‐based polyurethane. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Reactive dyeing of silk using commercial acid dyes based on a three‐component Mannich‐type reaction

Acid dyes are employed for commercially dyeing silk, which results in ionic bonds between the silk fibroin and the dye. This generally leads to low wet fastness properties for dyed silk fabrics. In this work, three commercial acid dyes with aromatic primary amine structures were selected to dye silk using a Mannich‐type reaction, resulting in improved wet fastness of dyed silk by forming covalent bonds between silk fibroin and dye. The Mannich‐type reactive dyeing was applied to silk fabrics at both 30 and 90°C in trials. Dyeing at 90°C can shorten the dyeing time compared with dyeing at 30°C, even although dye exhaustion and relative fixation at 90°C were a little lower. The dyeing process was optimised when the dyeing temperature was 90°C, dyebath pH 4, dye‐to‐formaldehyde ratio 1:30 and holding dyeing time 60 minutes. The results showed that the dye exhaustion on silk fabrics for the three aromatic primary amine‐containing acid dyes exceeded 94% and their relative fixation was over 80%. Their washing and rubbing fastness reached grade 4 or higher. Hence, the colour fastness properties of dyed silk fabrics using the Mannich‐type reactive dyeing method is superior to the conventional acid dyeing method using the same aromatic primary amine‐containing acid dyes. The Mannich‐type reactive dyeing for silk fabrics at 90°C can be developed into a novel and rapid reactive dyeing method, promising an effective dyeing process with excellent colour fastness.     

Soft segmental effect of methylene bis(p‐cyclohexyl isocyanate) based thermoplastic polyurethane impregnated with lithium perchlorate/propylene carbonate on ionic conductivity

Thermoplastic polyurethane (TPU) was employed as the polymer matrix for ion conduction as gelled electrolytes with lithium perchlorate (LiClO₄) in propylene carbonate (PC) solution. The TPU was prepared by methylene bis(p‐cyclohexyl isocyanate) as the hard segment while employing both poly(ethylene glycol) (PEG) and poly(tetramethylene glycol) (PTMG) as the soft segments. The copolymer comprising both PEG and PTMG was prepared such that it possessed the combined characteristics of good conductivity from the former and good mechanical properties from the latter. All the polymers were characterized by gel permeation chromatography, differential scanning calorimetry, and Fourier transform IR spectroscopy. The conductivity data were obtained from alternating current impedance experiments. The results revealed that the copolymer containing both PEG and PTMG as the soft segments showed better performance than TPU containing either PEG or PTMG. The copolymer TPU(PEG/PTMG) proved to be a good gelled electrolyte from 5 to 85°C. This copolymer, impregnated with 150% LiClO₄/PC, possessed good mechanical strength and conductivity as high as 10^?3 S/cm. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 935–942, 2001     

Supercritical carbon dioxide‐assisted loosening preparation of dry leather

The physical modification of the dry leather using supercritical carbon dioxide (SC‐CO₂) was studied in this article. A series of loosening processes of the leather fibers were carried out by changing the experimental conditions such as experimental pressure, experimental temperature, and time. The samples were characterized by scanning electronic microscopy (SEM), Brunauer–Emmett–Teller (BET) and X‐ray diffraction (XRD). SEM images show that samples were loosened by SC‐CO₂ and the leather fibers in micron size arrange more orderly after treatment. The BET surface area of treated samples increase from 1.67 m²/g to 6.33 m²/g with the changing of conditions. The optimal treatment conditions were determined. Moreover, XRD patterns indicate that aggregation structure of collagen fibers in the sample was altered by SC‐CO₂, and it can be found that the loosening of leather mostly happened in amorphous regions of collagen fibers. Besides, the percent breaking elongation of the samples was examined by means of a tensile analyzing test, and it indicates that the elongation at break of all the treated samples in SC‐CO₂ can increase to 128.2% compared with 95.9% of the original ones. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009