Enhancing Electrical Properties in NBT–KBT Lead-Free Piezoelectric Ceramics by Optimizing Sintering Temperature

Conventional sintering of (Na_{1− x} K _x )_0.5Bi_0.5TiO₃ (abbreviated as NKBT x , x =18–22 mol%) lead-free piezoelectric ceramics was investigated to clarify the optimal sintering temperature for densification and electrical properties. Both sintered density and electrical properties were sensitive to sintering temperature; particularly, the piezoelectric properties deteriorated when the ceramics were sintered above the optimum temperature. The NKBT20 and NKBT22 ceramics synthesized at 1110°–1170°C showed a phase transition from tetragonal to rhombohedral symmetry, which was similar to the morphotropic phase boundary (MPB). Because of such MPB-like behavior, the highest piezoelectric constant ( d ₃₃) of about 192 pC/N with a high electromechanical coupling factor ( k _p) of about 32% were obtained in the NKBT22 ceramics sintered at 1150°C.     

Influences of Sintering Temperature on Piezoelectric, Dielectric and Ferroelectric Properties of Li/Ta-Codoped Lead-Free (Na,K)NbO3 Ceramics

Li/Ta-codoped lead-free (Na,K)NbO₃ ceramics with a nominal composition of [(Na_0.535K_0.480)_0.942Li_0.058](Nb_0.90Ta_0.10)O₃ were synthesized normally at 1070°–1100°C. The XRD patterns of all samples show a single pervoskite structure with tetragonal symmetry. Although MPB separating the orthorhombic and tetragonal symmetries was absent, the maximum piezoelectric coefficient ( d ₃₃), electromechanical coupling coefficient ( k _p), Curie temperature ( T _c), and remanent polarization ( P _r) were optimized as 216 pC/N, 38.1%, 445°C, and 8.73 μC/cm², respectively.     

Effect of ZnO and CuO on the Sintering Temperature and Piezoelectric Properties of a Hard Piezoelectric Ceramic

Hard piezoelectrics with high dielectric and piezoelectric constants are used for high-power applications. However, the sintering temperature of these ceramics is high, around 1200°C, restricting the usage of cheap base metal electrodes in fabrication of multi-layer components. This study investigates the effect of CuO and ZnO on the sintering temperature of a hard piezoelectric, APC 841, which is a MnO₂- and Nb₂O₅-modified PZT. The addition of CuO decreased the sintering temperature through the formation of a liquid phase. However, the piezoelectric properties of the CuO-added ceramics sintered at ≤950°C were lower than the desired values. The addition of ZnO resulted in a significant improvement in the piezoelectric properties. This enhancement was attributed to the formation of a homogeneous microstructure with large grains. The APC 841+0.2 wt% CuO+1.1 wt% ZnO ceramics sintered at 950°C showed excellent piezoelectric and dielectric properties with values of k _p=0.532, Q _m=750, d ₃₃=351 pC/N, ɛ₃₃/ɛ_o=1337, and T _c=280°C.     

Low-Temperature Sintering of K0.5Na0.5NbO3 Ceramics

The objective of this work was to lower the sintering temperature of K_0.5Na_0.5NbO₃ (KNN) without reducing its piezoelectric properties. The KNN was sintered using 0.5, 1, 2, and 4 mass% of (K, Na)-germanate. The influence of the novel sintering aid, based on alkaline germanate with a melting point near 700°C, on the sintering, density, and piezoelectric properties of KNN is presented. The alkaline-germanate-modified KNN ceramics reach up to 96% of theoretical density at sintering temperatures as low as 1000°C, which is approximately 100°C less than the sintering temperature of pure KNN. The relative dielectric permittivity (ɛ/ɛ₀) and losses (tanδ), measured at 10 kHz, the piezo d ₃₃ coefficient, the electromechanical coupling and mechanical quality factors ( k _p, k _t, Q _m) of KNN modified with 1 mass% of alkaline germanate are 397, 0.02, 120 pC/N, 0.40, 0.44, and 77, respectively. These values are comparable to the best values obtained for KNN ceramics sintered above 1100°C.     

Effect of CuO on the Sintering Temperature and Piezoelectric Properties of (Na0.5K0.5)NbO3 Lead-Free Piezoelectric Ceramics

When a small amount of CuO was added to (Na_0.5K_0.5)NbO₃ (NKN) ceramics sintered at 960°C for 2 h, a dense microstructure with increased grains was developed, probably due to liquid-phase sintering. The Curie temperature slightly increased when CuO exceeded 1.5 mol%. The Cu²⁺ ion was considered to have replaced the Nb⁵⁺ ion and acted as a hardener, which increased the E _c and Q _m values of the NKN ceramics. High piezoelectric properties of k _p=0.37, Q _m=844, and ɛ₃ ^T /ɛ₀=229 were obtained from the specimen containing 1.5 mol% of CuO sintered at 960°C for 2 h.     

Phase Transitional Behavior and Piezoelectric Properties of Lead-Free (Na0.5K0.5)NbO3–(Bi0.5K0.5)TiO3 Ceramics

(1− x )(Na_0.5K_0.5)NbO₃–(Bi_0.5K_0.5)TiO₃ solid solution ceramics were successfully fabricated, exhibiting a continuous phase transition with changing x at room temperature from orthorhombic, to tetragonal, to cubic, and finally to tetragonal symmetries. A morphotropic phase boundary (MPB) between orthorhombic and tetragonal ferroelectric phases was found at 2–3 mol% (Bi_0.5K_0.5)TiO₃ (BKT), which brings about enhanced piezoelectric and electromechanical properties of piezoelectric constant d ₃₃=192 pC/N and planar electromechanical coupling coefficient k _p=45%. The MPB composition has a Curie temperature of 370°–380°C, comparable with that of the widely used PZT materials. These results demonstrate that this system is a promising lead-free piezoelectric candidate material.     

Phase Transitions and Electrical Properties of (Na1−xKx)(Nb1−ySby)O3 Lead-Free Piezoelectric Ceramics With a MnO2 Sintering Aid

Lead-free piezoelectric ceramics (Na_{1− x} K _x )(Nb_{1− y} Sb _y )O₃+ z mol% MnO₂ have been prepared by a conventional solid-state sintering technique. Our results reveal that Sb⁵⁺ diffuses into the K_0.5Na_0.5NbO₃ lattices to form a solid solution with a single-phase orthorhombic perovskite structure. The partial substitution of Sb⁵⁺ for B-site ion Nb⁵⁺ decreases the paraelectric cubic-ferroelectric tetragonal phase transition ( T _c) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition ( T _O–F), and retains strong ferroelectricity. A small amount of MnO₂ is enough to improve the densification of the ceramics. The co-effects of MnO₂ doping and Sb substitution lead to significant improvements in ferroelectric and piezoelectric properties. The ceramics with x =0.45–0.525, y =0.06–0.08, and z =0.5–1 exhibit excellent ferroelectric and piezoelectric properties: d ₃₃=163–204 pC/N, k _P=0.47–0.51, k _t=0.46–0.52, ɛ=640–1053, tan δ=1.3–3.0%, P _r=18.1–22.6 μC/cm², E _c=0.72–0.98 kV/mm, and T _C=269°–314°C.     

Sintering and Electrical Properties of Lead-Free Na0.5K0.5NbO3 Piezoelectric Ceramics

Lead-free Na_0.5K_0.5NbO₃ (NKN) piezoelectric ceramics were fairly well densified at a relatively low temperature under atmospheric conditions. A relative density of 96%–99% can be achieved by either using high-energy attrition milling or adding 1 mol% oxide additives. It is suggested that ultra-fine starting powders by active milling or oxygen vacancies and even liquid phases from B-site oxide additives mainly lead to improved sintering. Not only were dielectric properties influenced by oxide additives, such as the Curie temperature ( T _c) and dielectric loss ( D ), but also the ferroelectricity was modified. A relatively large remanent polarization was produced, ranging from 16 μC/cm² for pure NKN to 23 μC/cm² for ZnO-added NKN samples. The following dielectric and piezoelectric properties were obtained: relative permittivity ɛ ^T ₃₃/ɛ ₀ =570–650, planar mode electromechanical coupling factor, k _p=32%–44%, and piezoelectric strain constant, d ₃₃=92–117 pC/N.     

Properties of Modified Lead Zirconate Titanate Ceramics Prepared at Low Temperature (800°C) by Hot Isostatic Pressing

High-density lead zirconate titanate (PZT) ceramics were fabricated for the first time at a temperature as low as 800°C via the hot isostatic pressing (HIP) of a PZT powder with a modified composition of 0.92Pb(Zr_0.53Ti_0.47)O₃—0.05BiFeO₃—0.03Ba(Cu_0.5W_0.5)O₃ that contained 0.5 mass% MnO₂. The resultant PZT ceramics exhibited a microstructure that was denser and finer than that of PZT sintered at 935°C, which is the lowest temperature for the densification of the same composition via normal sintering. The relevant dielectric and piezoelectric properties of the HIPed PZT ceramics were as follows: coefficient of electromechanical coupling ( K ₃₁), 31.8%; mechanical quality factor ( Q _m), 1364; piezoelectric constant ( d ₃₁), −73.7 × 10⁻¹² C/N; relative dielectric constant (ɛ₃₃^T/ɛ₀), 633; dielectric loss factor (tan δ), 0.5%; Curie temperature ( T _c), 285°C; and density (ρ), 8.06 g/cm³. In addition to these reasonably good piezoelectric properties, the HIPed PZT exhibited better mechanical properties—particularly, higher fracture strength—than the normally sintered PZT.     

Spark Plasma Sintering of Nano-Sized TiN Prepared from TiO2 by Controlled Hydrolysis of TiCl4 and Ti(O-i-C3H7)4 Solution

Nano-sized TiO₂ powders were prepared by controlled hydrolysis of TiCl₄ and Ti(O-i-C₃H₇)₄ solutions and nitrided in flowing NH₃ gas at 700°–1000°C to form TiN. Nano-sized TiN was densified by spark plasma sintering at 1300°–1600°C to produce TiN ceramics with a relative density of 98% at 1600°C. The microstructure of the etched ceramic surface was observed by SEM, which revealed the formation of uniformly sized 1–2 μm grains in the TiCl₄-derived product and 10–20 μm in the Ti(O-i-C₃H₇)₄-derived TiN. The electric resisitivity and Vickers micro-hardness of the TiN ceramics was also measured.     

BiNbO4-Based Glass–Ceramic Composites for Microwave Applications

The effect of a bespoke glass sintering aid, 0.3Bi₂O₃–0.3Nb₂O₅–0.3B₂O₃–0.1SiO₂ (BN1), developed from the base ceramic composition, BiNbO₄ (BN), on the sinterability, microstructure, and microwave (MW) dielectric properties of BN ceramics has been investigated. Densities >97% theoretical could be achieved at 1020°C for samples with up to 15% BN1 additions. The resulting microstructure was composed of BN laths surrounded by a residual glass phase that contained small fibrous crystals. Some evidence of dissolution of BN crystals was observed. Optimum properties were exhibited for samples with 15 wt% of glass addition sintered for 4 h at 1020°C with a relative permittivity ɛ_r=38, a MW quality factor Q × f ₀=17 353 at 5.6 GHz, and a temperature coefficient of resonant frequency τ_f=−10 ppm/°C. The high Q × f ₀, ɛ_r, and low τ_f, coupled with a relatively low sintering temperature, suggest that the use of bespoke glass sintering aids of this type may have great potential for the fabrication of MW ceramics.     

Effects of La on Dielectric and Piezoelectric Properties of Pb1−xLa2x/3(Nb0.95Ti0.0625)2 O6 Ceramics

Ceramics with the chemical compositions of Pb_{1− x} La_{2 x /3}(Nb_0.95Ti_0.0625)₂O₆ (0≤ x ≤0.060) (PLTN) were prepared by the conventional solid-state reaction method. X-ray diffraction analysis indicated that Ti and La doping not only decreased the rhombohedral–tetragonal phase transformation temperature, but also stabilized the orthorhombic phase of PLTN ceramics. All ceramics sintered at 1190°–1250°C had shown the pure orthorhombic ferroelectric phase. La doping suppresses grain growth and inhibits the formation of pores and cracks, resulting in an increase in relative density up to 97%. The amount of La doping to PLTN ceramics obviously affect ceramics' piezoelectric constant ( d ₃₃) and dielectric loss (tanδ). The sample with x =0.015 possesses high Curie temperature ( T _c=560°C), low dielectric loss (tanδ=0.0054), and excellent piezoelectric constant ( d ₃₃=92 pC/N), presenting a high potential to be used in high-temperature applications as piezoelectric transducers.     

K/Na Ratio Dependence of the Electrical Properties of [(KxNa1−x)0.95Li0.05](Nb0.95Ta0.05)O3 Lead-Free Ceramics

[(K _x Na_{1− x} )_0.95Li_0.05](Nb_0.95Ta_0.05)O₃ (K _x NLNT) ( x= 0.40–0.60) lead-free piezoelectric ceramics were prepared by conventional solid-state sintering. The effects of K/Na ratio on the dielectric, piezoelectric, and ferroelectric properties of the K _x NLNT ceramics were studied. The experimental results show that the electrical properties strongly depend on the K/Na ratio in the K _x NLNT ceramics. The K _x NLNT ( x =0.42) ceramics exhibit enhanced properties ( d ₃₃∼242 pC/N, k _p∼45.7%, k _t∼47%, T _c∼432°C, T _o−t =48°C, ɛ_r∼1040, tanδ∼2.0%, P _r∼26.4 μC/cm², E _c∼10.3 kV/cm). Enhanced electrical properties of the K _x NLNT ( x =0.42) ceramics could be attributed to the polymorphic phase transition near room temperature. These results show that the K _x NLNT ( x =0.42) ceramic is a promising lead-free piezoelectric material.     

Low-Temperature Sintering and Piezoelectric Properties of CuO-Added 0.95(Na0.5K0.5)NbO3–0.05BaTiO3 Ceramics

The sintering temperature of 0.95(Na_0.5K_0.5)NbO₃–0.05BaTiO₃ (NKN–BT) ceramics needs to be decreased below 1000°C to prevent Na₂O evaporation, which can cause difficulties in poling and may eventually degrade their piezoelectric properties. NKN–BT ceramics containing CuO were well sintered at 950°C with grain growth. Poling was easy for all specimens. Densification and grain growth were explained by the formation of a liquid phase. The addition of CuO improved the piezoelectric properties by increasing the grain size and density. High piezoelectric properties of d ₃₃=230 pC/N, k _p=37%, and ɛ₃^T/ɛ₀=1150 were obtained from the specimen containing 1.0 mol% of CuO synthesized by the conventional solid-state method.     

Phase Structure and Electrical Properties of (K0.48Na0.52)(Nb0.95Ta0.05)O3-LiSbO3 Lead-Free Piezoelectric Ceramics

(1− x )(K_0.48Na_0.52)(Nb_0.95Ta_0.05)O₃– x LiSbO₃ [(1− x )KNNT− x LS] lead-free piezoelectric ceramics were prepared by the conventional solid-state sintering method. A morphotropic phase boundary (MPB) between orthorhombic and tetragonal phases was identified in the composition range of 0.03< x <0.05. The ceramics near the MPB exhibit a strong compositional dependence and enhanced electrical properties. The (1− x )KNNT– x LS ( x =0.04) ceramics exhibit good electrical properties ( d ₃₃=250 pC/N, k _p=45.1%, k _t =46.3%, T _c=348°C, T _{o − t} =74°C, P _r=25.9 μC/cm², E _c=10.7 kV/cm, ɛ_r∼1352, tan δ∼3%). These results show that (1− x )KNNT– x LS ceramic is a promising lead-free piezoelectric material.     

Double Precursor Solution Coating Approach for Low-Temperature Sintering of [Pb(Mg1/3Nb2/3)O3]0.63[PbTiO3]0.37 Solids

Lead-based piezoelectric ceramics typically require sintering temperatures higher than 1000°C at which significant lead loss can occur. Here, we report a double precursor solution coating (PSC) method for fabricating low-temperature sinterable polycrystalline [Pb(Mg_1/3Nb_2/3)O₃]_0.63-[PbTiO₃]_0.37 (PMN–PT) ceramics. In this method, submicrometer crystalline PMN powder was first obtained by dispersing Mg(OH)₂-coated Nb₂O₅ particles in a lead acetate/ethylene glycol solution (first PSC), followed by calcination at 800°C. The crystalline PMN powder was subsequently suspended in a PT precursor solution containing lead acetate and titanium isopropoxide in ethylene glycol to form the PMN–PT precursor powder (second PSC) that could be sintered at a temperature as low as 900°C. The resultant d ₃₃ for samples sintered at 900°, 1000°, and 1100°C for 2 h were 600, 620, and 700 pm/V, respectively, comparable with the known value. We attributed the low sintering temperature to the reactive sintering nature of the present PMN–PT precursor powder. The reaction between the nanosize PT and the submicrometer-size PMN occurred roughly in the same temperature range as the densification, 850°–900°C, thereby significantly accelerating the sintering process. The present PSC technique is very general and should be readily applicable to other multicomponent systems.     

Processing and Electrical Properties in Lead-Based (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) Systems

Lead-based ferroelectric (FE) ceramics exhibit superior electromechanical properties; therefore, there has been an increased focus on developing new lead-based FE materials with high Curie temperature ( T _c) and enhanced properties. The aim of this study was to investigate new compositions in the Pb(Mg_1/3Nb_2/3)O₃–Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ ( PMN–PYbN–PT) system to enhance the electromechanical properties while increasing the T _c and lowering the sintering temperature. The 0.575[0.5PMN–0.5PYbN]–0.425PT composition at PMN/PYbN (50/50) mole ratio were prepared by reactive sintering PMNT and PYbNT powder mixtures at 950°–1200°C for 4 h. PMNT and PYbNT powders were calcined via the columbite method. Samples were prepared by cold isostatic pressing at 80 MPa. Dense and fully perovskite 0.575[0.5PMN–0.5PYbN]–0.425PT ceramics were fabricated at 975°C for 4 h, and these samples displayed a remnant polarization ( P _r) of 32 μ C/cm², coercive field ( E _c) of 17 kV/cm, and a piezoelectric charge coefficient ( d ₃₃) of 475 pC/N. It is proposed that this ternary system can be tailored for various applications.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Phase Structure, Microstructure, and Electrical Properties of Sb-Modified (K, Na, Li) (Nb, Ta) O3 Piezoelectric Ceramics

Lead-free (K_0.44Na_0.52Li_0.04)(Nb_{0.80− x} Ta_0.20Sb _x )O₃ piezoelectric ceramics were prepared by the ordinary sintering method. The much higher Pauling electronegativity of Sb compared with Nb makes the ceramics more covalent. By increasing x from 0.00 to 0.06, the phase structure of the ceramics changed from the tetragonal to the pseudocubic phase, and both the bands in the Raman scattering spectra shifted to lower frequency numbers. The grain growth of the ceramics was improved by substituting Sb⁵⁺ for Nb⁵⁺. By increasing x , the dielectric properties were optimized and the variation of dielectric constants before and after poling became smaller. Only the tetragonal–cubic phase transition was observed above room temperature in all the ɛ_r– T curves. The degree of diffuseness increased from 1.29 at x =0.00 to 1.96 at x =0.06, indicating that the ceramics at x =0.06 changed to an approximate ideal relaxor ferroelectric. The temperature dependences of f _r and k _p became better by increasing x properly. Significantly, the ceramics with x between 0.00 and 0.04 had high density and outstanding electrical properties ( d ₃₃=241–272pC/N, k _p=0.42–0.52, ɛ_r=1258–1591, tan δ=0.015–0.025, T _c=280°–355°C, E _c=10.62–12.60 kV/cm, and P _r=16.19–20.13 μC/cm²). Besides, the underlying mechanism for variations of the electrical properties due to Sb⁵⁺ substitution was explained in this work.     

Preparation of Undoped Lead Titanate Ceramics via Sol-Gel Processing

Crack-free, undoped PbTiO₃ ceramics were fabricated successfully using sol–gel-synthesized powder prepared from chelated titanium alkoxide and lead acetate. The sintered ceramics, 8.3 mm in diameter and 6–8 mm thick, were 96% dense. In the present study, PbTiO₃ ceramics with excess lead (Pb:Ti = 1.1:1.0) had large grains, averaging 14.3 μm. Lower-lead ceramics (Pb:Ti = 1.0:1.0 and 0.9:1.0) had smaller grains, averaging 1.8 μm. The PbTiO₃ ceramics with a high lead content cracked during sintering at 1150°C, whereas the other ceramics did not crack. Excess lead, in a more-than-stoichiometric ratio, promoted grain growth and caused disintegration of the ceramics. Therefore, uncracked PbTiO₃ ceramics apparently can be fabricated by avoiding excess lead, possibly because restricted grain growth in low-lead ceramics causes low residual stress over many small grains during transition. The electrical properties measured in the present study for PbTiO₃ ceramics with a Pb:Ti ratio of 1:1 are d ₃₃= 35 pC/N, K ₃= 64, k _p= 0.59, and k _t≈ 0.