Techno-economic evaluation of advanced IGCC lignite coal fuelled power plants with CO2 capture

The techno-economic evaluation of four novel integrated gasification combined cycle (IGCC) power plants fuelled with low rank lignite coal with CO₂ capture facility has been investigated using ECLIPSE process simulator. The performance of the proposed plants was compared with two conventional IGCC plants with and without CO₂ capture. The proposed plants include an advanced CO₂ capturing process based on the Absorption Enhanced Reforming (AER) reaction and the regeneration of sorbent materials avoiding the need for sulphur removal component, shift reactor and/or a high temperature gas cleaning process. The results show that the proposed CO₂ capture plants efficiencies were 18.5–21% higher than the conventional IGCC CO₂ capture plant. For the proposed plants, the CO₂ capture efficiencies were found to be within 95.8–97%. The CO₂ capture efficiency for the conventional IGCC plant was 87.7%. The specific investment costs for the proposed plants were between 1207 and 1479 €/kW_e and 1620 €/kW_e and 1134 €/kW_e for the conventional plants with and without CO₂ capture respectively. Overall the proposed IGCC plants are cleaner, more efficient and produce electricity at cheaper price than the conventional IGCC process.     

Competitiveness of CO2 capture from an industrial solid oxide fuel cell combined heat and power system in the early stage of market introduction

In this article, it was investigated whether potentially low-cost CO₂ capture from SOFC systems could enhance the penetration of SOFC in the energy market in a highly carbon-constrained society in the mid-term future (up to year 2025). The application of 5 MWe SOFC systems for industrial combined heat and power (CHP) generation was considered. For CO₂ capture, oxyfuel combustion of anode off-gas using commercially available technologies was selected. Gas turbine (GT-) CHP plant was considered to be the reference case.Technical results showed that despite the energy penalties due to CO₂ capture and compression, net electrical and heat efficiencies were nearly identical with or without CO₂ capture. This was due to higher heat recovery efficiency by separating SOFC off-gas streams for CO₂ capture. However, CO₂ capture significantly increased the required SOFC and heat exchanger areas.Economic results showed that for above 40-50 $ t⁻¹ CO₂ price, SOFC-CHP systems were more economical when equipped with CO₂ capture. CO₂ capture also enabled SOFC-CHP to compete with GT-CHP at higher cell stack production costs. At zero CO₂ price, cell stack production cost had to be as low as 140 kW⁻¹ for SOFC-CHP to outperform GT-CHP. At 100 $ t⁻¹ CO₂ price, the cell stack production cost requirement raised to 350 $ kW⁻¹. With CO₂ capture, SOFC-CHP still outperformed GT-CHP at a significantly higher cell stack production cost above 900 $ kW⁻¹.     

An economic feasibility study of O2/CO2 recycle combustion technology based on existing coal-fired power plants in China

In order to reduce the CO₂ emission from the coal-fired power plants, O₂/CO₂ recycle combustion (Oxy-combustion) technique has been proposed through combining a conventional combustion process with a cryogenic air separation process. The technique is capable of enriching CO₂ concentration and then allowing CO₂ sequestration in an efficient and energy-saving way. Taking into account the CO₂ taxation and CO₂ sale, the paper evaluates the economic feasibility of Oxy-combustion plants retrofitted from two typical existing conventional coal-fired power plants (with capacities of 2 × 300 MW and 2 × 600 MW, respectively) with Chinese data. The cost of electricity (COE) and the CO₂ avoidance cost (CAC) are also considered in the evaluation. The COE of the retrofitted Oxy-combustion plant is nearly the same as that of the corresponding conventional plant if the unit price of CO₂ sale reaches 17-22 $/t (different cases). The CAC of the retrofitted 2 × 300 MW Oxy-combustion plant is 1-3 $/t bigger than that of the retrofitted 2 × 600 MW Oxy-combustion plant. Supercritical plants are more economical and appropriate for Oxy-combustion retrofit. The result indicates that Oxy-combustion technique is not only feasible for CO₂ emission control based on existing power plants but is also cost-effective.     

Amine modified mesocellular siliceous foam (MCF) as a sorbent for CO2

Adsorption is considered a promising method for carbon capture. CO₂ adsorbents take a variety of forms - but one approach is to fill mesoporous substrates with a polymeric CO₂ selective sorbent. SBA-15 and mesocellular siliceous foam (MCF) are high pore volume, high surface area ordered mesoporous materials for which modification with amine should result in high capacity, highly selective adsorbents. SBA-15 and MCF were separately loaded with approximately one pore volume equivalent of linear polyethyleneimine (PEI) (M_w = 2500) or branched PEI (M_n = 1200). CO₂ adsorption/desorption isotherms under dry CO₂ were obtained at 75, 105 and 115 °C. The CO₂ adsorption/desorption kinetics were improved with temperature, though the CO₂ capacities generally decreased. The adsorption capacity for MCF loaded with branched PEI at 105 and 115 °C were 151 and 133 mg/g adsorbent, respectively (in 50% CO₂/Ar, 20 min adsorption time). These are significantly higher than the adsorption capacity observed for SBA-15 loaded with branched PEI under same conditions, which were 107 and 83 mg/g adsorbent, respectively. Thus the results indicate that, on a unit mass basis, amine modified MCF's are potentially better adsorbents than amine modified SBA-15 for CO₂ capture at modestly elevated temperature in a vacuum swing adsorption process.     

Enhancement of reactivity in surfactant-modified sorbent for CO2 capture in pressurized carbonation

The calcination/carbonation loop of calcium-based (Ca-based) sorbents is considered as a viable technique for CO₂ capture from combustion gases. Recent attempts to improve the CO₂ uptake of Ca-based sorbents by adding calcium lignosulfonate (CLS) with hydration have succeeded in enhancing its effectiveness. The optimum mass ratio of CLS/CaO is 0.5 wt.%. The reduction in particle size and grain size of CaO appeared to be parts of the reasons for increase in CO₂ capture. The primary cause of increase in reactivity of the modified sorbents was the ability of the CLS to retard the sintering rate and thus to remain surface area and pore volume for reaction. The CO₂ uptake of the modified sorbents was also enhanced by elevating the carbonation pressure. Experimental results indicate that the optimal reaction condition of the modified sorbents is at 0.5 MPa and 700 °C and a high conversion of 0.7 is achieved after 10 cycles, by 30% higher than that of original limestone, at the same condition.     

Optimization of CO2 capture process with aqueous amines using response surface methodology

Amine is one of candidate solvents that can be used for CO₂ recovery from the flue gas by conventional chemical absorption/desorption process. In this work, we analyzed the impact of different amine absorbents and their concentrations, the absorber and stripper column heights and the operating conditions on the cost of CO₂ recovery plant for post-combustion CO₂ removal. For each amine solvent, the optimum number of stages for the absorber and stripper columns, and the optimum absorbent concentration, i.e., the ones that give the minimum cost for CO₂ removed, is determined by response surface optimization. Our results suggest that CO₂ recovery with 48 wt% DGA requires the lowest CO₂ removal cost of $43.06/ton of CO₂ with the following design and operating conditions: a 20-stage absorber column and a 7-stage stripper column, 26 m³/h of solvent circulation rate, 1903 kW of reboiler duty, and 99°C as the regenerator-inlet temperature.     

Separation and capture of carbon dioxide from CO2/H2 syngas mixture using semi-clathrate hydrates

The relation between anthropogenic emissions of CO₂ and its increased levels in the atmosphere with global warming and climate change has been well established and accepted. Major portion of carbon dioxide released to the atmosphere, originates from combustion of fossil fuels. Integrated gasification combined cycle (IGCC) offers a promising fossil fuel technology considered as a clean coal-based process for power generation particularly if accompanied by precombustion capture. The latter includes separation of carbon dioxide from a synthesis gas mixture containing 40 mol% CO₂ and 60 mol% H₂.A novel approach for capturing CO₂ from the above gas mixture is to use gas hydrate formation. This process is based on selective partition of CO₂ between hydrate phase and gas phase and has already been studied with promising results. However high-pressure requirement for hydrate formation is a major problem.We have used semiclathrate formation from tetrabutylammonium bromide (TBAB) to experimentally investigate CO₂ capture from a mixture containing 40.2 mol% of CO₂ and 59.8 mol% of H₂. The results shows that in one stage of gas hydrate formation and dissociation, CO₂ can be enriched from 40 mol% to 86 mol% while the concentration of CO₂ in equilibrium gas phase is reduced to 18%. While separation efficiency of processes based on hydrates and semi-clathrates are comparable, the presence of TBAB improves the operating conditions significantly. Furthermore, CO₂ concentration could be increased to 96 mol% by separating CO₂ in two stages.     

Gasoline-range hydrocarbon synthesis over Co/SiO2/HZSM-5 catalyst with CO2-containing syngas

Selective synthesis of gasoline-range hydrocarbons (C₅-C₁₂) was investigated in a fixed-bed micro reactor using two series of CO₂-containing syngas with various mole CO₂/(CO + CO₂) and H₂/(CO + CO₂) ratios, where Fischer-Tropsch synthesis(FTS) and in situ hydrocracking/hydroisomerization were performed over bifunctional Co/SiO₂/HZSM-5 catalyst. CO₂ was converted at 0.15-0.55 of CO₂/(CO + CO₂) ratio under H₂-rich condition (H₂/(CO + CO₂) = 2.0), highest conversion of 20.3% at 0.42. Further increasing CO₂ content decreased CO₂ conversion and quite amount of CO₂ acted as diluting component. For the syngas with low H₂ content or H₂/(CO + CO₂) ratio(< 1.85, H₂/CO = 2.0), the competitive adsorption of CO, H₂ and CO₂ resulted in low CO, CO₂ and total carbon conversion, which was 57.9%, 12.7% and 31.4% respectively at 0.74 of H₂/(CO + CO₂) ratio(H₂/CO/CO₂/N₂ = 40.8/20.4/34.8/4). FTS results indicated that high H₂ content and proper H₂/(CO + CO₂) ratio were favorable for the conversion of CO₂-containing syngas. More than 45% selectivity to gasoline-range hydrocarbons including isoparaffins was obtained under the two series of syngas. It was also tested that the catalytic activity of Co/SiO₂/HZSM-5 kept stable under CO₂-containing syngas(< 7.5%). And the quick catalytic deactivation under high CO₂ containing syngas(H₂/CO/CO₂/N₂ = 45.3/23.2/27.1/3.06) was due to carbon deposition and pore blockage by heavy hydrocarbon, tested by thermal gravimetry, N₂ physisorption and scanning electron microscopy(SEM).     

Modelling of an IGCC plant with carbon capture for 2020

Currently several industrial scale IGCC - carbon capture demonstration plants are being planned. Thermodynamic simulations are a useful tool to investigate the optimal plant configuration. In order to demonstrate the potential of the next generation of IGCC with CCS a thermodynamic model was developed using conventional but improved technology. The plant concept was verified and simulated for a generic hard coal and lignite. The simulation showed a net efficiency (LHV) of 38.5% and 41.9% for hard coal and lignite, respectively.The results are consistent with current studies but also indicate that major simulations were too optimistic. The auxiliary demand of an IGCC plant with carbon capture can be expected with 21 to 24% based on gross output. The drop in efficiency compared to the none-capture case is estimated with roughly 11 to 12%-points. During a sensitivity study the impact of process changes on plant efficiency and economics is evaluated. Releasing the captured CO₂ without compression is found to be economically favourable at CO₂ prices below 15 €/t and electricity prices above 100 €/MWh. Further the impact of carbon capture rate is quantified and an efficiency potential is indicated for lower CO₂ quality.     

The calcium looping cycle for CO2 capture from power generation, cement manufacture and hydrogen production

Calcium looping is a CO₂ capture scheme using solid CaO-based sorbents to remove CO₂ from flue gases, e.g., from a power plant, producing a concentrated stream of CO₂ (∼95%) suitable for storage. The scheme exploits the reversible gas-solid reaction between CO₂ and CaO(s) to form CaCO₃(s). Calcium looping has a number of advantages compared to closer-to-market capture schemes, including: the use of circulating fluidised bed reactors—a mature technology at large scale; sorbent derived from cheap, abundant and environmentally benign limestone and dolomite precursors; and the relatively small efficiency penalty that it imposes on the power/industrial process (i.e., estimated at 6-8 percentage points, compared to 9.5-12.5 from amine-based post-combustion capture). A further advantage is the synergy with cement manufacture, which potentially allows for decarbonisation of both cement manufacture and power production. In addition, a number of advanced applications offer the potential for significant cost reductions in the production of hydrogen from fossil fuels coupled with CO₂ capture. The range of applications of calcium looping are discussed here, including the progress made towards demonstrating this technology as a viable post-combustion capture technology using small-pilot scale rigs, and the early progress towards a 2 MW scale demonstrator.     

CO2 capture using some fly ash-derived carbon materials

Adsorption is considered to be one of the more promising technologies for capturing CO₂ from flue gases. For post-combustion capture, the success of such an approach is however dependent on the development of an adsorbent that can operate competitively at relatively high temperatures. In this work, low cost carbon materials derived from fly ash, are presented as effective CO₂ sorbents through impregnation these with organic bases, for example, polyethylenimine aided by polyethylene glycol. The results show that for samples derived from a fly ash carbon concentrate, the CO₂ adsorption capacities were relatively high (up to 4.5 wt%) especially at high temperatures (75 °C), where commercial active carbons relying on physi-sorption have low capacities. The addition of PEG improves the adsorption capacity and reduces the time taken for the sample to reach the equilibrium. No CO₂ seems to remain after desorption, suggesting that the process is fully reversible.     

Development of new alumina-modified sorbents for CO2 sorption and regeneration at temperatures below 200 °C

A new regenerable alumina-modified sorbent was developed for CO₂ capture at temperatures below 200 °C. The CO₂ capture capacity of a potassium-based sorbent containing Al₂O₃ (KAlI) decreased during multiple CO₂ sorption (60 °C) and regeneration (200 °C) tests due to the formation of the KAl(CO₃)(OH)₂ phase, which could be converted into the original K₂CO₃ phase above 300 °C. However, the new regenerable potassium-based sorbent (Re-KAl(I)) maintained its CO₂ capture capacity during multiple tests even at a regeneration temperature of 130 °C. In particular, the CO₂ capture capacity of the Re-KAl(I)60 sorbent which was prepared by the impregnation of Al₂O₃ with 60 wt.% K₂CO₃ was about 128 mg CO₂/g sorbent. This excellent CO₂ capture capacity and regeneration property were due to the characteristics of the Re-KAl(I) sorbent producing only a KHCO₃ phase during CO₂ sorption, unlike the KAlI30 sorbent which formed the KHCO₃ and KAl(CO₃)(OH)₂ phases even at 60 °C. This result was explained through the structural effect of the support containing the KAl(CO₃)(OH)₂ phase which was prepared by impregnation of Al₂O₃ with K₂CO₃ in the presence of CO₂.     

Design and operation of pilot plant for CO2 capture from IGCC flue gases by combined cryogenic and hydrate method

This project is a trial conducted under contract with CO₂CRC, Australia of a new CO₂ capture technology that can be applied to integrated gasification combined cycle power plants and other industrial gasification facilities. The technology is based on combination of two low temperature processes, namely cryogenic condensation and the formation of hydrates, to remove CO₂ from the gas stream. The first stage of this technology is condensation at −55 °C where CO₂ concentration is expected to be reduced by up to 75 mol%. Remaining CO₂ is captured in the form of solid hydrate at about 1 °C reducing CO₂ concentration down to 7 mol% using hydrate promoters. This integrated cryogenic condensation and CO₂ hydrate capture technology hold promise for greater reduction of CO₂ emissions at lower cost and energy demand. Overall, the process produced gas with a hydrogen content better than 90 mol%. The concentrated CO₂ stream was produced with 95-97 mol% purity in liquid form at high pressure and is available for re-use or sequestration. The enhancement of carbon dioxide hydrate formation and separation in the presence of new hydrate promoter is also discussed. A laboratory scale flow system for the continuous production of condensed CO₂ and carbon dioxide hydrates is also described and operational details are identified.     

Preparation of a highly microporous carbon from a carpet material and its application as CO2 sorbent

In order to increase the use of carpet wastes (pre- and/or post-consumer wastes), this work studies for the first time the preparation and characterisation of a microporous material from a commercial carpet (pile fiber content: 80% wool/20% nylon; primary and secondary backings: woven polypropylene; binder: polyethylene) and its application for CO₂ capture. The porous material was prepared from an entire carpet material using a standard chemical activation with KOH and then, characterised in terms of their porous structure and surface functional groups. Adsorption of CO₂ was studied using a thermogravimetric analyser at several temperatures (25-100 °C) and under different CO₂ partial pressures (i.e. pure CO₂ flow and a ternary mixture of 15% CO₂, 5% O₂ and 80% N₂). In order to examine the adsorbent regenerability, multiple CO₂ adsorption/desorption cycles were also carried out. The surface area and micropore volume of the porous adsorbent were found to be 1910.17 m² g^− 1 and 0.85 cm³ g^− 1, respectively. The CO₂ adsorption profiles illustrate that the maximum CO₂ capture on the sample was reached in less than 10 min. CO₂ adsorption capacities up to 8.41 wt.% and 3.37 wt.% were achieved at 25 and 70 °C, respectively. Thermal swing regeneration studies showed that the prepared adsorbent has good cyclic regeneration capacities.     

Microporous phenol-formaldehyde resin-based adsorbents for pre-combustion CO2 capture

Different types of phenolic resins were used as precursor materials to prepare adsorbents for the separation of CO₂ in pre-combustion processes. In order to obtain highly microporous carbons with suitable characteristics for the separation of CO₂ and H₂ under high pressure conditions, phenol-formaldehyde resins were synthesised under different conditions. Resol resins were obtained by using an alkaline environment while Novolac resins were synthesised in the presence of acid catalysts. In addition, two organic additives, ethylene glycol (E) and polyethylene glycol (PE) were included in the synthesis. The phenolic resins thus prepared were carbonised at different temperatures and then physically activated with CO₂. The carbons produced were characterised in terms of texture, chemical composition and surface chemistry. Maximum CO₂ adsorption capacities at atmospheric pressure were determined in a thermogravimetric analyser. Values of up to 10.8 wt.% were achieved. The high-pressure adsorption of CO₂ at room temperature was determined in a high-pressure magnetic suspension balance. The carbons tested showed enhanced CO₂ uptakes at high pressures (up to 44.7 wt.% at 25 bar). In addition, it was confirmed that capture capacities depend highly on the microporosity of the samples, the narrow micropores (pore widths of less than 0.7 nm) being the most active in CO₂ adsorption at atmospheric pressure. The results presented in this work suggest that phenol-formaldehyde resin-derived activated carbons, particularly those prepared with the addition of ethylene glycol, show great potential as adsorbents for pre-combustion CO₂ capture.     

CO2 uptake of modified calcium-based sorbents in a pressurized carbonation-calcination looping

This study focuses on enhancing CO₂ uptake by modifying limestone with acetate solutions under pressurized carbonation condition. The multicycle tests were carried out in an atmospheric calcination/pressurized carbonation reactor system at different temperatures and pressures. The pore structure characteristics (BET and BJH) were measured as a supplement to the reaction studies. Compared with the raw limestone, the modified sorbent showed a great improvement in CO₂ uptake at the same reaction condition. The highest CO₂ uptake was obtained at 700 °C and 0.5 MPa, by 88.5% increase over the limestone at 0.1 MPa after 10 cycles. The structure characteristics of the sorbents on N₂ absorption and SEM confirm that compared with the modified sorbent, the effective pores of limestone are greatly driven off by sintering, which hinders the easy access of CO₂ molecules to the unreacted-active sites of CaO. The morphological and structural properties of the modified sorbent did not reveal significant differences after multiple cycles. This would explain its superior performance of CO₂ uptake under pressurized carbonation. Even after 10 cycles, the modified sorbent still achieved a CO₂ uptake of 0.88.     

Ca-based sorbent looping combustion for CO2 capture in pilot-scale dual fluidized beds

To demonstrate process feasibility of in situ CO₂ capture from combustion of fossil fuels using Ca-based sorbent looping technology, a flexible atmospheric dual fluidized bed combustion system has been constructed. Both reactors have an ID of 100 mm and can be operated at up to 1000 °C at atmospheric pressure. This paper presents preliminary results for a variety of operating conditions, including sorbent looping rate, flue gas stream volume, CaO/CO₂ ratio and combustion mode for supplying heat to the sorbent regenerator, including oxy-fuel combustion of biomass and coal with flue gas recirculation to achieve high-concentration CO₂ in the off-gas. It is the authors' belief that this study is the first demonstration of this technology using a pilot-scale dual fluidized bed system, with continuous sorbent looping for in situ CO₂ capture, albeit at atmospheric pressure. A multi-cycle test was conducted and a high CO₂ capture efficiency (> 90%) was achieved for the first several cycles, which decreased to a still acceptable level (> 75%) even after more than 25 cycles. The cyclic sorbent was sampled on-line and showed general agreement with the features observed using a lab-scale thermogravimetric analysis (TGA) apparatus. CO₂ capture efficiency decreased with increasing number of sorbent looping cycles as expected, and sorbent attrition was found to be another significant factor to be limiting sorbent performance.     

Exergoeconomic and exergoenvironmental evaluation of power plants including CO2 capture

CO₂ capture from power plants, combined with CO₂ storage, is a potential means for limiting the impact of fossil fuel use on the climate. In this paper, three oxy-fuel plants with incorporated CO₂ capture are evaluated from an economic and environmental perspective. The oxy-fuel plants, a plant with chemical looping combustion with near 100% CO₂ capture and two advanced zero emission plants with 100% and 85% CO₂ capture are evaluated and compared to a similarly structured reference plant without CO₂ capture. To complete the comparison, the reference plant is also considered with CO₂ capture incorporating chemical absorption with monoethanolamine. Two exergy-based methods, the exergoeconomic and the exergoenvironmental analyses, are used to determine the cost-related and the environmental impacts of the plants, respectively, and to reveal options for improving their overall effectiveness.For the considered oxy-fuel plants, the investment cost is estimated to be almost double that of the reference plant, mainly due to the equipment used for oxygen production and CO₂ compression. Furthermore, the exergoeconomic analysis reveals an increase in the cost of electricity with respect to the reference plant by more than 20%, with the advanced zero emission plant with 85% CO₂ capture being the most economical choice. On the other hand, a life cycle assessment reveals a decrease in the environmental impact of the plants with CO₂ capture, due to the CO₂ and NO_x emission control. This leads to a reduction in the overall environmental impact of the plants by more than 20% with respect to the reference plant. The most environmentally friendly concept is the plant with chemical looping combustion.     

Partial O2-fired coal power plant with post-combustion CO2 capture: A retrofitting option for CO2 capture ready plants

In the work presented in this paper, an alternative process concept that can be applied as retrofitting option in coal-fired power plants for CO₂ capture is examined. The proposed concept is based on the combination of two fundamental CO₂ capture technologies, the partial oxyfuel mode in the furnace and the post-combustion solvent scrubbing. A 330 MW_el Greek lignite-fired power plant and a typical 600 MW_el hard coal plant have been examined for the process simulations. In a retrofit application of the ECO-Scrub technology, the existing power plant modifications are dominated by techno-economic restrictions regarding the boiler and the steam turbine islands. Heat integration from processes (air separation, CO₂ compression and purification and the flue gas treatment) can result in reduced energy and efficiency penalties. In the context of this work, heat integration options are illustrated and main results from thermodynamic simulations dealing with the most important features of the power plant with CO₂ capture are presented for both reference and retrofit case, providing a comparative view on the power plant net efficiency and energy consumptions for CO₂ capture. The operational characteristics as well as the main figures and diagrams of the plant’s heat balances are included.     

Reactivation and remaking of calcium aluminate pellets for CO2 capture

CaO-based pellets supported with aluminate cements show superior performance in carbonation/calcination cycles for high-temperature CO₂ capture. However, like other CaO-based sorbents, their CO₂ carrying activity is reduced after increasing numbers of cycles under high-temperature, high-CO₂ concentration conditions. In this work the feasibility of their reactivation by steam or water and remaking (reshaping) was investigated. The pellets, prepared from three limestones, Cadomin and Havelock (Canada) and Katowice (Poland, Upper Silesia), were tested in a thermogravimetric analyzer (TGA). The cycles were performed under realistic CO₂ capture conditions, which included calcination in 100% CO₂ at temperatures up to 950 °C. Typically, after 30 cycles, samples were hydrated for 5 min with saturated steam at 100 °C in a laboratory steam reactor (SR). Moreover, larger amounts of pellets were cycled in a tube furnace (TF), hydrated with water and reshaped, and tested to determine their CO₂ capture activity in the TGA. It was found that, after the hydration stage, pellets recovered their activity, and more interestingly, pellets that had experienced a longer series of cycles responded more favorably to reactivation. Moreover, it was found that conversion of pellets increased after about 70 cycles (23%), reaching 33% by about cycle 210, with no reactivation step. Scanning electron microscope (SEM) analyses showed that the morphology of the low-porosity shell formed at the pellet surface during cycles, which limits conversion, was eliminated after a short period (5 min) of steam hydration. The nitrogen physisorption analyses (BET, BJH) of reshaped spent pellets from cycles in the TF confirmed that sorbent surface area and pore size distribution were similar to those of the original pellets. The main alumina compound in remade pellets as determined by XRD was mayenite (Ca₁₂Al₁₄O₃₃). These results showed that, with periodic hydration/remaking steps, pellets can be used for extended times in CO₂ looping cycles, regardless of capture/regeneration conditions.