Development of a microfabricated palladium decoupler/electrochemical detector for microchip capillary electrophoresis using a hybrid glass/poly(dimethylsiloxane) device

The fabrication and evaluation of a palladium decoupler and working electrode for microchip capillary electrophoresis (CE) with electrochemical detection is described. The use of the Pd decoupler allows the working electrode to be placed directly in the separation channel and eliminates the band-broadening characteristic of the end-channel configuration. The method used for fabrication of the decoupler and working electrode was based on thin-layer deposition of titanium followed by palladium onto a glass substrate. When employed as the cathode in CE, palladium absorbs the hydrogen gas that is generated by the hydrolysis of water. The effect of the decoupler size on the ability to remove hydrogen was evaluated with regard to reproducibility and longevity. Using boric acid and TES buffer systems, 500 microm was determined to be the optimum decoupler size, with effective voltage isolation lasting for approximately 6 h at a constant field strength of 600 V/cm. The effect of distance between the decoupler and working electrode on noise and resolution for the separation of dopamine and epinephrine was also investigated. It was found that 250 microm was the optimum spacing between the decoupler and working electrode. At this spacing, laser-induced fluorescence detection at various points around the decoupler established that the band broadening due to pressure-induced flow that occurs after the decoupler did not significantly affect the separation efficiency of fluorescein. Limits of detection, sensitivity, and linearity for dopamine (500 nM, 3.5 pA/microM, r(2) = 0.9996) and epinephrine (2.1 microM, 2.6 pA/microM, r(2) = 0.9996) were obtained using the palladium decoupler in combination with a Pd working electrode.     

Elimination of high-voltage field effects in end column electrochemical detection in capillary electrophoresis by use of on-chip microband electrodes

The influence of the separation voltage on end column electrochemical detection (EC) in capillary electrophoresis (CE) has been investigated using an electrochemical detector chip based on an array of microband electrodes. It is shown, both theoretically and experimentally, that the effect of the CE electric field on the detection can be practically eliminated, without using a decoupler, by positioning the reference electrode sufficiently close to the working electrode. In the present study, this was demonstrated by using an experimental setup in which neighboring microband electrodes on a chip, positioned 30 microns from the end of the CE capillary, were used as working and reference electrodes, respectively. The short distance (i.e., 10 microns) between the working and reference electrode ensured that both of the electrodes were very similarly affected by the presence of the CE electric field. With this experimental setup, no significant influence of the CE voltage on the peak potentials for gold oxide reduction could be seen for CE voltages up to +30 kV. The detector noise level was also found to be reduced.     

Three-electrode electrochemical detector and platinum film decoupler integrated with a capillary electrophoresis microchip for amperometric detection

This article demonstrates that a three-electrode electrochemical (EC) detector and an electric decoupler could be fabricated in the same glass chip and integrated with an O2-plasma-treated PDMS layer using microfabrication techniques to form the capillary electrophoresis (CE) microchip. The platinized decoupler could mostly decouple the electrochemical detection circuit from the interference of an separation electric field in 10 mM 2-(N-morpholino)ethanesulfonic acid (MES, pH 6.5) solution. The baseline offset of background current recorded from the working electrode with and without application of a separation electric field was maintained at less than 0.05 pA in 10 mM MES. In addition, the platinized pseudoreference electrode was demonstrated to offer a stable potential in electrochemical detection. As a consequence, the limit of detection of dopamine was 0.125 microM at a S/N = 4. The responses for dopamine to different concentrations were found to be linear between 0.25 and 50 microM with a correlation coefficient of 0.9974 and a sensitivity of 11.76 pA/microM. The totally integrated CE-EC microchip should be able to fulfill the ideal of miniaturization and commercialization.     

In-channel electrochemical detection in the middle of microchannel under high electric field

We propose a new method for performing in-channel electrochemical detection under a high electric field using a polyelectrolytic gel salt bridge (PGSB) integrated in the middle of the electrophoretic separation channel. The finely tuned placement of a gold working electrode and the PGSB on an equipotential surface in the microchannel provided highly sensitive electrochemical detection without any deterioration in the separation efficiency or interference of the applied electric field. To assess the working principle, the open circuit potentials between gold working electrodes and the reference electrode at varying distances were measured in the microchannel under electrophoretic fields using an electrically isolated potentiostat. In addition, "in-channel" cyclic voltammetry confirmed the feasibility of electrochemical detection under various strengths of electric fields (～400 V/cm). Effective separation on a microchip equipped with a PGSB under high electric fields was demonstrated for the electrochemical detection of biological compounds such as dopamine and catechol. The proposed "in-channel" electrochemical detection under a high electric field enables wider electrochemical detection applications in microchip electrophoresis.     

Simple and sensitive electrode design for microchip electrophoresis/electrochemistry

A simple and sensitive electrode design for microchip capillary electrophoresis/electrochemistry (CE-EC) is presented. The system employs metal microwires as the working electrodes for electrochemical detection. Two general approaches for integration of electrodes in microchip CE-EC are commonly used, end-channel and microfabrication. The end-channel approach allows electrode cleaning and the use of chemically modified electrodes; however, the designs generally lack portability and the ability to incorporate multiple electrodes. Microfabrication allows the incorporation of multiple electrodes on-chip and is easily made portable; however, it requires the use of expensive metallization and clean room facilities, and integration of more than one electrode material is challenging. The reported approach aligns a solid metal microwire through the separation channel allowing integration of multiple electrodes and the use of different electrode materials without sacrificing the portability. A detection limit of 100 nM for dopamine was achieved without the use of a decoupler as a result of a higher collection efficiency with the new design.     

Using channel depth to isolate and control flow in a micro free-flow electrophoresis device

A multiple-depth micro free-flow electrophoresis chip (mu-FFE) has been fabricated with a 20-microm-deep separation channel and 78-microm-deep electrode channels. Due to the difference in channel heights, the linear velocity of buffer in the electrode channels is approximately 15 times that of the buffer in the separation channel. Previous mu-FFE devices have been limited by electrolysis product formation at the electrodes. These electrolysis products, manifested as bubbles, decreased the electric field and disrupted the buffer flow profile, limiting performance and preventing continuous operation. Using channel depth to control buffer flow over the electrodes and in the separation channel effectively removes electrolysis products, allowing continuous operation. The linear velocities in the channels were confirmed using particle velocimetry and compared well with values predicted using lubrication theory. A separation potential of 645 V could be applied before significant Joule heating was observed. This corresponded to an electric field of 586 V/cm in the separation channel, a 4-fold increase over our previous design. A separation of fluorescent standards was demonstrated using the new mu-FFE device. Resolution increased by a factor of 1.3 over our previous design, even when operated under similar conditions, suggesting that effective removal of electrolysis products is more important than originally thought.     

On-column electrochemical detection for microchip capillary electrophoresis

The development of a cellulose acetate decoupler for on-column electrochemical detection in microchip capillary electrophoresis is presented. The capillary based laser-etched decoupler is translated to the planar format to isolate the detector circuit from the separation circuit. The decoupler is constructed by aligning a series of 20 30-microm holes through the coverplate of the microchip with the separation channel and casting a thin film of cellulose acetate within the holes. The decoupler shows excellent isolation of the detection circuit for separation currents up to 60 microA, with noise levels at or below 1 pA at a carbon fiber electrode. Detection limits of 25 nM were achieved for dopamine. This decoupler design combines excellent mechanical stability, effective shunting of high separation currents, and ease of manufacture.     

Capillary electrophoresis chips with a sheath-flow supported electrochemical detection system

Microfabricated capillary electrophoresis chips containing an integrated sheath-flow electrochemical detector are developed with the goal of minimizing the influence of separation voltages on end-column detection while maintaining optimum performance. The microdevice consists of an upper glass wafer carrying the etched separation, injection, and sheath-flow channels and a lower glass wafer on which gold- and silver-plated electrodes have been fabricated. The sheath-flow channels join the end of the separation channel from each side, and gravity-driven flow carries the analytes to the electrochemical detector placed at working distances of 100, 150, 200, and 250 microm from the separation channel exit. The performance of this detector is evaluated using catechol and a detection limit of 4.1 microM obtained at a working distance of 250 microm. Detection of DNA restriction fragments and PCR product sizing is demonstrated using the electroactive intercalating dye, iron phenanthroline. Additionally, an allele-specific, PCR-based single-nucleotide polymorphism typing assay for the C282Y substitution diagnostic for hereditary hemochromatosis is developed and evaluated using ferrocene-labeled primers. This study advances the feasibility of high-speed, high-throughput chemical and genetic analysis using microchip electrochemical detection.     

Dual-channel method for interference-free in-channel amperometric detection in microchip capillary electrophoresis

A novel in-channel amperometric detection method for microchip capillary electrophoresis (CE) has been developed to avoid the interference from applied potential used in the CE separation. Instead of a single separation channel as in conventional CE microchips, we use a dual-channel configuration consisting of two different parallel separation and reference channels. A working electrode (WE) and a reference electrode (RE) are placed equally at a distance 200 microm from its outlet on each channel. Running buffer flows through the reference channel. Our dual-channel CE microchips consist of a poly(dimethylsiloxane) (PDMS) upper plate and a glass lower plate to form a PDMS/glass hybrid chip. Amperometric signals are measured without any potential shift and interference from the applied CE potential, and CE separation maintains its high resolution because this in-channel configuration does not allow additional band broadening that is notorious in end-channel and off-channel configurations. The high performance of this new in-channel electrochemical detection methodology for CE has been demonstrated by analyzing a mixture of electrochemically active biomolecules: dopamine (DA), norepinephrine, and catechol. We have achieved a 0.1 pA detectability from the analysis of DA, which corresponds to a 1.8 nM concentration.     

Capillary electrophoresis coupled with electrochemiluminescence detection using porous etched joint

A new setup to couple capillary electrophoresis (CE) with electrochemiluminescence (ECL) detection is described in which the electrical connection of CE is achieved through a porous section at a distance of 7 mm from the CE capillary outlet. Because the porous capillary wall allowed the CE current to pass through and there was no electric field gradient beyond that section, the influence of CE high-voltage field on the ECL procedure was eliminated. The porous section formed by etching the capillary with hydrofluoric acid after only one side of the circumference of 2-3 mm of polyimide coating of the capillary was removed, while keeping the polyimide coating on the other part to protect the capillary from HF etching makes the capillary joint much more robust since only a part of the circumference of it is etched. A standard three-electrode configuration was used in experiments with Pt wire as a counter electrode, Ag/AgCl as a reference electrode, and a 300-microm diameter Pt disk as a working electrode. Compared with CE-ECL conventional decoupler designs, the present setup with a porous joint has no added dead volume created. Moreover, the dead volume can be increasingly decreased by shortening the distance ( approximately 100 microm) between the working electrode and the end of the separation capillary. The versatility in choice of capillaries and separation buffers within this design is the main advantage over the use of small i.d. capillary and low conductivity buffer in some CE-ECL systems. The performance of this setup is illustrated by the analyses of tripropylamine and proline.     

Miniaturized electrochemical flow cells

Several novel types of miniaturized electrochemical flow cells are described. The flow cells are fabricated in fluorinated ethylene propylene using a novel technique where channels with inner diameters down to 13 microm are integrated with electrodes. The channel is formed by shrinking and simultaneous melting of a heat shrink/melt tubing around a channel template (a tungsten wire) and electrodes followed by removal of the channel template. The technique allows incorporation of different electrode materials of different sizes. The electrode configuration consists of one or two working electrodes inside the channel and a counter electrode located in the channel outlet reservoir. Electrode configurations with different channel and working electrode sizes, different electrode materials including carbon fibers, glassy carbon rods, poly(tetrafluoroethylene)/carbon composite material, and platinum wires, and different arrangements have been assembled. Hydrodynamic voltammograms in dual-electrode (generator-collector) experiments indicate good potential control for cells with 25-microm channels, while there is some iR drop in cells with 13-microm channels. Cells prepared with a cylindrical working electrode tangent and perpendicular to a flow channel show a flow rate dependence consistent with thin-layer cell behavior. Electrode areas can be made in the range of 10(-10)-10(-8) m2.     

Electrochemical detection method for nonelectroactive and electroactive analytes in microchip electrophoresis

In this work, we establish an indirect amperometric detection method via mounting a single carbon fiber disk working electrode in the end part of a microchannel. This in-channel configuration for microchip capillary electrophoresis brings about that the potential of the working electrode in the case of electrochemical reduction reaction is coupled by the separation electric field, while the potential of the working electrode in the case of electrochemical oxidation reaction is not coupled by the separation electric field. Such a special performance provides a convenient and sensitive approach for indirectly detecting nonelectroactive analytes that relies on amperometric response of dissolved oxygen in solution and directly detecting electroactive analytes based on their own amperometric response on the carbon fiber electrode. This method has shown its essential importance in the analysis of inorganic cations, biomolecules, and electroosmotic flow rates. Based on preliminary results, a detection limit of 1.0 microM for K(+) and Na(+) have been achieved.     

Characteristic electrochemical responses of polymer microchannel-microelectrode chips

Polymer microchannel chips (dimension of the channel, 20 microm (depth) x 100 microm (width)) integrated with dual microband electrodes were fabricated by an imprinting method, and their characteristic electrochemical responses were elucidated in detail. A silicon micromachined template fabricated by photolithography and dry etching techniques was used for imprinting. An aqueous solution of a ferrocene derivative was brought into the microchannel by pressure-driven flow, and the electrode responses were studied on the basis of voltammetry and chronoamperometry. A linear sweep voltammetry of 1-hydroxyethylferrocene (FeCp-OH) in water demonstrated that the electrode responses in the microchannel chip were best characterized by one-dimensional diffusion along the channel length, reflecting the structural dimension of the channel. In generation-collection mode experiments, furthermore, a collection efficiency as high as approximately 90% was attained in the microchannel owing to both restricted space and characteristics of solution flow in the channel. It was confirmed that diffusion and solution flow made molecular transport very efficient in the microchannel. The experimental results were also compared with those predicted by computer simulations.     

Microchip capillary electrophoresis with an integrated indium tin oxide electrode-based electrochemiluminescence detector

This paper describes an indium tin oxide (ITO) electrode-based Ru(bpy)3(2+) electrochemiluminecence (ECL) detector for a microchip capillary electrophoresis (CE). The microchip CE-ECL system described in this article consists of a poly(dimethylsiloxane) (PDMS) layer containing separation and injection channels and an electrode plate with an ITO electrode fabricated by a photolithographic method. The PDMS layer was reversibly bound to the ITO electrode plate, which greatly simplified the alignment of the separation channel with the working electrode and enhanced the photon-capturing efficiency. In our study, the high separation electric field had no significant influence on the ECL detector, and decouplers for isolating the separation electric field were not needed in the microchip CE-ECL system. The ITO electrodes employed in the experiments displayed good durability and stability in the analytical procedures. Proline was selected to perform the microchip device with a limit of detection of 1.2 microM (S/N = 3) and a linear range from 5 to 600 microM.     

Capillary-electrode alignment by an optical-fiber connector for amperometric detection in capillary electrophoresis

We describe here an electrochemical cell ideal for routine analysis of CE-EC experiments (capillary electrophoresis coupled with electrochemical detection). The cell was modified from a fiber-optic connector, named MT, which allowed frequent change and fast alignment between a pair of 4-strand fiber ribbons. The relative standard deviations of the current response and migration time for 100 microM dopamine were, respectively, 3.7 and 0.5% in five repetitive routines of disconnecting, polishing, and assembling the CE cell. The time required for alignment of the separation capillary and the working electrode was < 10 s, once all components were assembled in an MT fiber-optic plug. These features enabled CE-EC users to polish the working electrode and reassemble the EC cell as in HPLC-EC. However, to accommodate the channel dimensions of the commercially available MT, a special order capillary with outer diameter of 125 microm is necessary at this stage.     

In-channel electrochemical detection for microchip capillary electrophoresis using an electrically isolated potentiostat

A new electrode configuration for microchip capillary electrophoresis (CE) with electrochemical (EC) detection is described. This approach makes it possible to place the working electrode directly in the separation channel. The "in-channel" EC detection was accomplished without the use of a decoupler through the utilization of a specially designed, electrically isolated potentiostat. The effect of the working electrode position on the separation performance (in terms of plate height and peak skew) of poly(dimethylsiloxane)-based microchip CEEC devices was evaluated by comparing the more commonly used end-channel configuration with this new in-channel approach. Using catechol as the test analyte, it was found that in-channel EC detection decreased the total plate height by a factor of 4.6 and lowered the peak skew by a factor of 1.3. A similar trend was observed for the small, inorganic ion nitrite. Furthermore, a fluorescent and electrochemically active amino acid derivative was used to directly compare the separation performance of in-channel EC detection to that of a widely used laser-induced fluorescence (LIF) detection scheme. In this case, it was found that the plate height and peak skew for both detection schemes were essentially equal, and the separation performance of in-channel EC detection is comparable to LIF detection.     

Isoelectric focusing in a microfluidically defined electrophoresis channel

A new form of microchip isoelectric focusing that allows efficient coupling with pretreatment processes is reported. The sample is conveyed in a carrier ampholyte solution to the separation channel that is connected at both ends by two V-shaped lead channels, which supply electrode solutions to the connection point and complete the electrical connection to off-chip electrodes. The relatively high electric conductivity of the electrode solutions compared with that of the pH gradient enables focusing with a 2% loss of applied voltage at the electrodes using the lead channels. A glass microchip was constructed specifically for this configuration. The channel wall was coated with polydimethylacrylamide, and the IEF chip was operated in a chip holder equipped with on-chip connector valves. A plug of fluorescence-labeled peptide p I markers with p I values ranging from 3.64 to 9.56 with carrier ampholyte solution (pH 3-10) was introduced into the separation channel. When the plug reached the channel segment (24 mm in length) between the connection points with the electrolyte lead channels, isoelectric focusing was started after filling the lead channels with electrolyte solutions. The peptide markers were observed using scanning fluorescence detection. The entire range of the pH gradient was established in the segment after approximately 2 min. Isoelectric focusing of three consecutively injected sample plugs containing different p I markers was demonstrated.     

Dielectrophoretic and electrothermal effects at alternating current heated disk microelectrodes

When a disk microelectrode is polarized with an alternating potential of very high frequency (0.1-2 GHz) and a high amplitude (up to 2.8 V rms), the electrode is heated up, and at the same time, a very intense electric field is created around the electrode (>10(6) V/m for electrodes 1 microm in radius). This strong electric field gives rise to positive or negative dielectrophoretic effects. Positive dielectrophoretic effects can be used to assemble nanowires from nanoparticles at the electrode edge. On the other hand, a negative dielectrophoretic effect is probably responsible for "jet boiling" observed at overheated microelectrodes. In addition, a combination of a high temperature gradient and a high potential gradient generates an intense electrothermal flow of solution which very strongly enhances the mass transport and is responsible for intense convection in such systems. The electrothermal flow and dielectrophoretic forces can be generated directly on a microelectrode employed in electrochemical detection because the high frequency ac polarization of the electrode does not interfere with the acquisition of analytical signals.     

Microchip capillary electrophoresis with electrochemical detection

A novel microchip capillary electrophoresis system with electrochemical detection, using the replaceable microelectrode, is first reported. This kind of electrode can be fabricated in general laboratories and can be replaced quickly with electrodes of different materials according to the requirements of experiments. The end-column electrochemical detection on microchip CE was achieved by fixing the working electrode (such as carbon fiber, Pt, or Au, etc.) through a guide tube on the end of the separation channel. The experiment results indicate that the alignment of the electrode with the channel outlet can be carried out accurately and reproducibly, and therefore, the detection device has low noise and good reproducibility. The detection limit of dopamine is 2.4 x 10(-7) M, which is the lowest result reported so far. The separation and detection of dopamine, 5-hydroxytryptamine and epinephrine using carbon fiber and Pt microdisk electrodes within 50 s was successfully performed.     

On-chip electric field driven electrochemical detection using a poly(dimethylsiloxane) microchannel with gold microband electrodes

An external electric field driven in-channel detection technique for on-chip electrochemical detection in micro fabricated devices is described based on a microfluidic system containing an array of 20 microband electrodes. It is shown that an external electric field induces a potential difference between two gold microband electrodes in a poly(dimethylsiloxane) (PDMS) microchannel, and that this enables the electrochemical detection of electroactive species such as ascorbic acid and Fe(CN) 6 (4-). The results, which are supported by simulations of the behavior of the microband electrodes in the microfluidic system, show that the induced potential difference between the electrodes can be controlled by altering the external electric field or by using different microbands in the microband array. As the obtained currents depend on the concentrations of electroactive species in the flowing solution and the detection can be carried out anywhere within the channel without interference of the external electric field, the present approach significantly facilitates electrochemical detection in capillary electrophoresis. This approach consequently holds great promise for application in inexpensive portable chip-based capillary electrophoresis (CE) devices.