首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
In the present study, a simple, inexpensive, nontoxic, and environmentally friendly polyethylene glycol (PEG) polymer was used to enhance the hydrophilicity of the forward osmosis (FO) membrane using various PEG concentrations as a pore forming agent in the casting solution of polyethersulfone/polysulfone (PES/PSF) blend membranes. A nonwoven PES/PSF FO blend membrane was fabricated via the immersion precipitation phase inversion technique. The membrane dope solution was cast on polyethylene terephthalate (PET) nonwoven fabric. The results revealed that PEG is a pore forming agent and that adding PEG promotes membrane hydrophilicity. The membrane with 1 wt% PEG (PEG1) had about 27% lower contact angle than the pristine blend membrane. The PEG1 membrane has less tortuosity (which reduces from 3.4–2.73), resulting in a smaller structure parameter (S value) of 277 μm, due to the presence of open pores on the bottom surface structure, which results in diminished ICP. Using 1 M NaCl as the draw solution and distilled water as the feed solution, the PEG1 membrane exhibited higher water flux (136 L m−2 h−1) and lower reverse salt flux (1.94 g m−2 h−1). Also, the selectivity of the membrane, specific reverse salt flux, (Js/Jw) showed lower values (0.014 g/L). Actually, the PEG1 membrane has a 34.6% higher water flux than the commercial nonwoven-cellulose triacetate (NW-CTA) membrane. By means of varied concentrations of NaCl salt solution (0.6, 1, 1.5, and 2 M), the membrane with 1 wt% PEG showed improved FO separation performance with permeate water fluxes of 108, 136, 142, and 163 L m−2 h−1. In this work, we extend a promising gate for designing fast water flux PES/PSF/PEG FO blend membranes for water desalination.  相似文献   

2.
A novel thin film composite‐type forward osmosis (FO) membrane with inhibited concentration polarization phenomenon and expectant separation performance was prepared by continuous interfacial polymerization method. The nylon‐6,6 microfiltration membrane with the average pore size of 5 μm and the self‐wetting property was for the first time used as the supporting layer of the FO membranes, which decreased the mass transfer resistance in the porous supporting layer. The skin layer was prepared via the continuous interfacial polymerization of polyamide as a relatively dense layer, with the reverse salt flux of less than 1 g/m?2 h?1. The mass transfer resistance and the reverse salt flux of the prepared FO membranes were remarkably reduced due to the functional design of the double‐layer structure, which effectively enhanced the separation selectivity and restrain the concentration polarization of the FO membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45133.  相似文献   

3.
Forward osmosis (FO) membranes were prepared by a coating method with poly(ethylene glycol) crosslinked sulfonated polysulfone (SPSf) as a selective layer. The poly(ether sulfone)/SPSf substrate was prepared by phase inversion. The composite membranes were characterized with respect to membrane chemistry (by attenuated total reflectance/Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy), hydrophilicity (by static contact angle measurement), and surface morphology (by scanning electron microscopy and atomic force microscopy). The FO performance was also characterized. The effects of the crosslinker concentration on the hydrophilicity and FO performance were investigated. The crosslinked membrane exhibited a high hydrophilicity with a lowest contact angle of 15.5°. Under FO tests, the membranes achieved a higher water flux of 15.2 L m?2 h?1 when used against deionized water as the feed solution and a 2 mol/L sodium chloride (NaCl) solution as the the draw solution. The membranes achieved a magnesium sulfate rejection of 96% and an NaCl rejection of 55% when used against a 1 g/L inorganic salt solution as the feed solution and a 2 mol/L glucose solution as the draw solution. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43941.  相似文献   

4.
Development and use of novel membranes for forward osmosis (FO) applications have gained popularity throughout the world. To enhance FO membrane performance, a novel thin-film nanocomposite membrane was fabricated by interfacial polymerization incorporating Fullerenol (C60(OH)n) nanomaterial, having n in the range of 24–28 into the active layer. Different concentrations of fullerenol loading (100, 200, 400, and 800 ppm) were added to the top skin layer. The structural and surface properties of the pure thin-film composite membrane (TFC) and fullerenol-incorporated thin-film nanocomposite (FTFC) membranes, were characterized by ATR-FTIR, SEM, and AFM. FO performance and separation properties were evaluated in terms of water flux, reverse salt flux, antifouling propensity, water permeability and salt permeability for all TFC and FTFC membranes. Osmotic performance tests showed that FTFC membranes achieved higher water flux and reverse salt flux selectivity compared with those of TFC membranes. The FTFC membrane with a fullerenol loading of 400 ppm exhibited a water flux of 26.1 L m?2 h?1 (LMH), which is 83.03% higher than that of the TFC membrane with a specific reverse salt flux of 0.18 g/L using 1 M sodium chloride draw solution against deionized water in FO mode. The fullerenol incorporation in FTFC membranes also contributed to a decreased fouling propensity.  相似文献   

5.
A new cellulose acetate propionate (CAP) polymer has been synthesized and used to prepare high‐performance forward osmosis (FO) membranes. With an almost equal degree of substitution of acetyl and propionyl groups, the CAP‐based dense membranes show more balanced physicochemical properties than conventional cellulose acetate (CA)‐based membranes for FO applications. The former have a lower equilibrium water content (6.6 wt. %), a lower salt diffusivity (1.6×1014 m2 s?1) and a much lower salt partition coefficient (0.013) compared with the latter. The as‐prepared and annealed CAP‐based hollow fibers have a rough surface with an average pore radius of 0.31 nm and a molecular weight cut off of 226 Da. At a transmembrane pressure of 1 bar, the dual‐layer CAP‐CA hollow fibers show a pure water permeability of 0.80 L m?2 h?1 bar?1 (LMH/bar) and a rejection of 75.5% to NaCl. The CAP‐CA hollow fibers were first tested for their FO performance using 2.0 M NaCl draw solution and deionized water feed. An impressive water flux of 17.5 L m?2 h?1 (LMH) and a reverse salt flux of 2.5 g m?2 h?1 (gMH) were achieved with the draw solution running against the active CAP layer in the FO tests. The very low reverse salt flux is mainly resulting from the low salt diffusivity and salt partition coefficient of the CAP material. In a hybrid system combining FO and membrane distillation for wastewater reclamation, the newly developed hollow fibers show very encouraging results, that is, water production rate being 13–13.7 LMH, with a MgCl2 draw solution of only 0.5 M and an operating temperature of 343 K due to the incorporation of bulky propionyl groups with balanced physiochemical properties. © 2012 American Institute of Chemical Engineers AIChE J, 59: 1245–1254, 2013  相似文献   

6.
In this study, we report an easy and novel way to develop high flux aliphatic–aromatic-based thin-film composite (TFC) polyamide osmosis membranes by addition of inorganic metal salts with amine reactants in the reaction system of polyethylene imine (PEI) and 1,3-benzene dicarbonyl chloride. Inorganic metal salts like CuSO4, NiSO4, MgSO4, and Al2(SO4)3 added to block some of the amine groups of PEI through complexation which in turn changes the polycondensation reaction kinetics of amine acid chloride reaction. The prepared membranes were characterized using water contact angle and atomic force microscopy studies and the performances were evaluated both in reverse osmosis and forward osmosis mode. In presence of metal salts in reaction interface, the performance of TFC membranes was greatly enhanced and the optimum metal salt concentration was identified for individual metal salts for maximum performance enhancement. The effects of different anions for same metal ion and different molecular weight of PEI were evaluated on composite polyamide membrane performances. Water permeability (flux) of 63.48 L m?2 h?1 was achieved upon inorganic salt addition compared to the unmodified TFC membranes with flux of 42.1 L m?2 h?1 at similar salt rejection of ~95%. Based on the new findings, a conceptual model was proposed to explain the role of metal ion in amine solution on the resulting characteristics of aromatic–aliphatic type polyamide–polysulfone composite membrane.  相似文献   

7.
Thin-film composite (TFC) membranes comprised of a polyamide (PA) selective layer upon a porous substrate dominate the forward osmosis (FO) membrane market. However, further improvement of perm-selectivity still remains a great challenge. Herein, a polyethyleneimine (PEI) interlayer is intentionally designed prior to interfacial polymerization (IP) to tailor the PA layer, which thus improves the separation performance. The PEI interlayer not only improves the substrate hydrophilicity for adsorbing more diamine monomer and controlling its release rate, but also participates in IP reaction by crosslinking with acyl chloride (TMC). Furthermore, it can decrease the electronegativity of the substrate for decreasing reverse salt diffusion. Consequently, a denser, thinner and smoother PA layer is formed due to the uniform distribution, controllable release of diamine monomer and the extra crosslinking between PEI and TMC. Furthermore, the PA layer becomes more hydrophilic with PEI involvement. As a result, the asprepared TFC membrane exhibits a favorable water flux of 16.1 L m−2 h−1 and an extremely low reverse salt flux (1.25 g m−2 h−1). Meanwhile, it achieves an excellent perm-selectivity with a ratio of water to salt permeability coefficient of 8.25 bar−1. Moreover, it exhibits an outstanding antifouling capacity. The work sheds light on fabricating high perm-selective membranes for desalination.  相似文献   

8.
Cellulose triacetate (CTA) membranes were fabricated via a modified nonsolvent induced phase separation (NIPS) method. Different solvent-nonsolvent compositions in first coagulation bath (FCB) were introduced to optimize CTA membrane structures. The effects of FCB compositions, immersion time and mass ratio of solvent (N-methyl-2-pyrrolidone, NMP) and nonsolvent (water, ethanol, ethylene glycol and glycerol) on membrane morphology and performance were systematically investigated. Prospective membranes with a dense bottom layer and a scaffold-like top layer were obtained under room temperature, owing to the low relative energy difference (RED) between nonsolvent and polymer as well as the high viscosity of FCBs. A high water flux Jv (12.6 L m?2 h?1) and a low reserve salt flux Js (1.32 g m?2 h?1) were obtained in the optimized membrane, with a structural parameter S of 119 μm. Compared with membranes prepared via conventional NIPS method and commercial CTA forward osmosis (FO) membranes, a remarkable improvement of Js/Jv value and S value was achieved, indicating membranes with single dense-layer structure might suffer less from internal concentration polymerization (ICP) which is the main obstacle for the development of FO process. This study might help us pave the way to design superior CTA membrane structures for forward osmosis application.  相似文献   

9.
Cellulose triacetate (CTA) forward‐osmosis (FO) membranes were prepared via the phase inversion method. The influence of thickness on the performance and morphology of CTA FO membranes was discussed in detail. When the thickness of the membrane was 50.0 ± 0.5 μm (CTA4), the prototype CTA membranes displayed a water flux of 20.2 L m?2 h?1 and a reverse salt transport of 14.6 g m?2 h?1 using 1 mol/L NaCl as the draw solution and deionized water as the feed solution during the FO process at 25 °C. In addition, the high‐performance CTA4 FO membranes have been used to process spent electroless nickel plating baths where the water flux could reach 13 L m?2 h?1 and NiSO4·6H2O crystals occurred in the feed solution of the spent electroless nickel plating baths. The recovery rates of NiSO4·6H2O and water from the spent electroless nickel plating baths were 44.54% and 53.53%, respectively. This study focused on improving membrane design for the FO process and finding a new method of waste liquor or wastewater treatment. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45049.  相似文献   

10.
In this work, a novel approach to improve the antifouling properties of membrane surfaces was developed. First, a polydopamine layer was attached onto the surface of an ultrahigh molecular weight polyethylene/fabric composite microporous membrane based on dopamine self‐polymerization and adhesive behavior. Then, methoxy polyethylene glycol amine was covalently bonded with the polydopamine layer via a Schiff base reaction. The physicochemical properties of the modified composite membrane surface were investigated, and the results indicated this modification could effectively enhance the membrane surface hydrophilicity. Furthermore, the protein fouling resistance of both dopamine‐coated and methoxy polyethylene glycol amine immobilized composite membranes was evaluated. It was found that a dopamine coating cannot obviously enhance the membrane antifouling properties due to its strong bioadhesion behavior. However, the antifouling properties of the composite membranes were significantly improved after being immobilized with a methoxy polyethylene glycol amine layer. Consequently, a layer‐by‐layer modified composite membrane with excellent antifouling property was obtained. The pure water flux and flux recovery ratio of the resultant membrane were 764 L m?2 h?1 and 83%, respectively. The aim of this paper was to provide an effective approach to optimizing the separation efficiency and antifouling performance of the ultrahigh molecular weight polyethylene/fabric composite membrane. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46428.  相似文献   

11.
Outer‐selective thin‐film composite (TFC) hollow fiber membranes offer advantages like less fiber blockage in the feed stream and high packing density for industrial applications. However, outer‐selective TFC hollow fiber membranes are rarely commercially available due to the lack of effective ways to remove residual reactants from fiber's outer surface during interfacial polymerization and form a defect‐free polyamide film. A new simplified method to fabricate outer‐selective TFC membranes on tribore hollow fiber substrates is reported. Mechanically robust tribore hollow fiber substrates containing three circular‐sector channels were first prepared by spinning a P84/ethylene glycol mixed dope solution with delayed demixing at the fiber lumen. The thin wall tribore hollow fibers have a large pure water permeability up to 300 L m?2 h?1 bar?1. Outer‐selective TFC tribore hollow fiber membranes were then fabricated by interfacial polymerization with the aid of vacuum sucking to ensure the TFC layer well‐attached to the substrate. Under forward osmosis studies, the TFC tribore hollow fiber membrane exhibits a good water flux and a small flux difference between active‐to‐draw (i.e., the active layer facing the draw solution) and active‐to‐feed (i.e., the active layer facing the feed solution) modes due to the small internal concentration polarization. A hyperbranched polyglycerol was further grafted on top of the newly developed TFC tribore hollow fiber membranes for oily wastewater treatment. The membrane displays low fouling propensity and can fully recover its water flux after a simple 20‐min water wash at 0.5 bar from its lumen side, which makes the membrane preferentially suitable for oil‐water separation. © 2015 American Institute of Chemical Engineers AIChE J, 61: 4491–4501, 2015  相似文献   

12.
Cellulose acetate (CA) is a low cost and readily available material widely used in forward osmosis (FO) membranes. However, the performance of pure CA membranes is not good enough in salt separation and the traditional modification methods are generally multistep and difficult to control. In this paper, we reported high performance cellulose acetate (CA) composite forward osmosis (FO) membranes modified with polyvinyl alcohol (PVA) and polydopamine (PDA). PVA was first cross-linked onto the surface of CA membranes, and then PDA was coated with a rapid deposition method. The membranes were characterized with respect to membrane chemistry (FTIR and XPS), surface properties comprising wettability (by water contact angle), and osmosis performance. The modified membrane coated by PVA and PDA shown better hydrophilicity and exhibited 16.72 LMH osmotic water flux and 0.14 mMH reverse solute flux with DI water as feed solution and 2.0 M NaCl as draw solution and active layer facing the feed solution. This simple and highly effective modification method makes it as an excellent candidate for further exploration for FO.  相似文献   

13.
Polysulfonamide (PSA), with its chemical stability and acid-resistance, is seen as a potential material for reverse osmosis. However, the present PSA thin film composite membranes fabricated via prevailing interfacial polymerization (IP) approach generally exhibited nonfavored desalination performance. In this work, PSA membrane was assembled via spinning-assist layer-by-layer (sLbL) on a poly(vinyl alcohol) modified polyethersulfone substrate. Fabrication was carried out through sequential interfacial reaction between naphthalene-1,3,6-trisufonylchloride and piperazine by alternately dipping and drying the substrate in two monomer phases. Morphology, chemical composition, surface charge distribution as well as surface hydrophilicity were investigated as a function of repeated cycles. The sLbL assembly approach implemented facile control over membrane properties with well-organized selective layer thickness growth and twofold to threefold reduced surface roughness. As measured from spectroscopic ellipsometry, the sLbL assembled membranes exhibited a linear thickness growth at ~2.72 nm per layer. Performance test indicated that the salt rejection and water flux showed a trade-off pattern with increasing layer number. The PSA membrane with five layers showed a preferable NaCl rejection of 95.7 ± 0.4% with a water flux of 12.4 ± 0.9 L m−2 h−1 at 10 bar, whereas the IP membrane exhibited only 58% and a 22.12 L m−2 h−1 flux. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47138.  相似文献   

14.
Membrane hydrophilicity influences the transport of water through the membrane in osmotically driven separations such as forward osmosis. In this paper, we coated the polysulfone support layer of two types of commercially available reverse osmosis membranes (brackish water and seawater) with hydrophilic polyvinyl alcohol (PVA). The aim of this was to increase the support layer hydrophilicity and, correspondingly, the rate of water transport through the membrane. Previous work with polydopamine coatings of the polysulfone support of reverse osmosis membranes has yielded promising results. In this work, we explore more readily available materials. Specifically, we studied the effects of two different PVA crosslinking agents – maleic acid and glutaraldehyde – on the resultant membrane properties and osmotic performance. For seawater membranes we found that PVA crosslinked to a limited degree with maleic acid creates a significant improvement in water flux in RO and FO systems, as compared to membranes with PVA crosslinked by glutaraldehyde. However, brackish water membranes did not have comparably significant changes in membrane performance. We conclude that the smaller pores of the brackish water membrane become clogged, and this effect is magnified by the lack of fractional free volume available within PVA that is highly crosslinked with glutaraldehyde.  相似文献   

15.
The poly(2‐hydroxyethyl methacrylate) grafted titanium dioxide nanoparticles were synthesized and added to the substrate of flat‐sheet thin film composite forward osmosis (TFC‐FO) membranes. The hydrophilicity of substrate was improved, which was advantageous to enhance the water flux of TFC‐FO membranes. The membranes containing a 3 wt % TiO2‐PHEMA in the substrate exhibited a finger‐like structure combined with sponge‐like structure, while those with lower or without TiO2‐PHEMA content showed fully finger‐like structures. As for FO performance, the TFC‐FO membranes with 3 wt % TiO2‐PHEMA content achieved the highest water flux of 42.8 LMH and 24.2 LMH against the DI water using 2M NaCl as the draw solution tested under the active layer against draw solution (AL‐DS) mode and active layer against feed solution (AL‐FS) mode, respectively. It was proven that the hydrophilic property of membrane substrates was a strong factor influencing the water flux in FO tests. Furthermore, the structural parameter was remarkably decreased with an increase of TiO2‐PHEMA content in membrane substrate, indicating the reducing of internal concentration polarization. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43719.  相似文献   

16.
This paper investigates the synthesis of graphene oxide (GO)-incorporated polyamide thin-film nanocomposite (TFN) membranes on polysulfone substrate for forward osmosis applications. The GO nanosheets were embedded into polyamide layer using different concentrations (0.05?0.2 wt%). The results represented the alteration of polyamide surface by GO nanosheets and enhancing the surface hydrophilicity by increasing the GO loading. The results showed that the water flux for 0.1 wt% GO embedded nanocomposite (TFN) membrane was 34.7 L/m2 h, representing 90% improvement compared to the thin-film composite, while the salt reverse diffusion was reduced up to 39%.  相似文献   

17.
There has been a resurgence of interest in forward osmosis (FO) as a potential means of desalination, dewatering and in pressure retarded osmosis, which Sidney Loeb was advocating over 3 decades ago. This paper describes the characteristics and potential applications of a newly developed FO hollow fiber membrane, which was fabricated by interfacial polymerization on the inner surface of a polyethersulfone (PES) hollow fiber. This FO membrane presents excellent intrinsic separation properties, with a water flux of 42.6 L/m2 h using 0.5 M NaCl as the draw solution and DI water as the feed with the active layer facing the draw solution orientation at 23 °C. The corresponding ratio of salt flux to water flux was only 0.094 g/L, which is superior to all other FO membranes reported in the open literature. To evaluate different application scenarios, various NaCl solutions (500 ppm (8.6 mM), 1 wt.% (0.17 M) and 3.5 wt.% (0.59 M)) were used as the feed water to test the performance of the FO membrane. The membrane can achieve a water flux of 12.4 L/m2 h with 3.5 wt.% NaCl solution as the feed and 2 M NaCl as the draw solution, suggesting it has good potential for seawater desalination.  相似文献   

18.
A new type of membrane has been prepared for hyperfiltration (reverse osmosis) desalination that is essentially a very thin polyelectrolyte membrane. It is prepared by casting an aqueous solution of a polyelectrolyte, specifically poly(acrylic acid) (PAA), directly on one surface of a finely porous support membrane. In hyperfiltration tests, these composite membranes exhibit desalination performance comparable in dilute solutions to that observed with cellulose acetate membranes of the Loeb-Sourirajan type. The water flux through these membranes is linear in the pressure up to 100 atm. Salt rejection is a function of pressure; it is also a function of the concentration of the feed solution and the charge of the counterion, in qualitative agreement with the Donnan ion-exclusion mechanism. Typical long-term results range from water fluxes of 2 × 10?3 g/cm2-sec (50 gal/ft2-day) and 80% salt rejection to 0.2 × 10?3 g/cm2-sec (5 gal/ft2-day) and >99.5% salt rejection at 1500 psi with 0.3 wt-% NaCl. These membranes appear to be useful for brackish water desalination.  相似文献   

19.
In this study, novel nanofiltration membranes were prepared with acrylonitrile–butadiene–styrene (ABS)–poly(ethylene glycol)–N,N ‐dimethylacetamide–[tetrahydrofuran (THF)–acetone] as a cosolvent. All of the membranes were prepared by the phase‐inversion method and a casting solution technique. The effects of the cosolvent concentration in the casting solution and the evaporation time before the immersion/precipitation step on the membrane performance and properties were investigated. The prepared membranes were characterized through their permeation flux, salt rejection, and phase‐inversion time values. The salt rejection was increased from 53% for the bare ABS membrane to 73% for the membrane prepared with 40 wt % THF as a cosolvent. The water flux was decreased from 4345 to 1121 cc m?2 h?1 with the addition of THF to the casting solution. The addition of acetone to the casting solution improved the water flux from 4345 to 5607 cc m?2 h?1 and reduced the salt rejection from 53 to 36%. The evaporation time of THF and acetone led to similar effects on flux and rejection. However, with evaporation time, membranes prepared with acetone were denser than those prepared with THF; this was due to the lower boiling point and higher boiling rate of acetone at the same temperatures. This resulted in greater effects on the ABS performance and structure. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44993.  相似文献   

20.
《分离科学与技术》2012,47(13):2895-2912
Abstract

Flat sheet ultrafiltration membranes from cellulose acetate (CA)/low cyclic dimer polysulfone (LCD PSf) were prepared by a phase inversion method. N, N′‐Dimethyl formamide and different molecular weight of polyethylene glycol (PEG 200, PEG 400, and PEG 600) were used as solvent and pore‐forming additive, respectively. The membranes were characterized in terms of pure water flux, water content, porosity, membrane hydraulic resistance, and morphology. The pure water flux was found to reach the highest value of 181.82 Lm?2h?1 at 5 wt.% PEG of 600 molecular weight and 10 wt.% LCD PSf content in the blended solution for membrane preparation. SEM micrographs indicated that the addition of PEG into the CA/LCD PSf solution changes the inner structure of the membrane. The influence of filtration time and applied pressure on membrane permeability was examined by copper/polyethylenimine complex rejection studies. With increase in filtration time, the rejection of the copper/polyethylenimine complex decreased and the results were discussed.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号