红外线聚光非球面透镜的单点金刚石镜面切削方法

根据硬脆性材料的延性域加工机理和面形误差补偿加工方法,研究了圆弧形和平头形刀具的单点金刚石延性域切削方法,在加工中直接获得了镜面切除面;并利用数控技术进行误差补偿,克服了因加工试验、刀具磨损、机械振动、热变形等造成的加工误差导致的非球面的面形精度降低和表面粗糙度恶化.并将该方法用于采用圆弧形刀具对红外线聚光的φ70mm非球面锗透镜进行单点金刚石切削实验中.试验结果表明面形误差补偿加工方法可以进一步消除加工误差,将非球面的面形精度PV值从微米级(1.23μm)提高到亚微米级(0.36μm)的程度,表面粗糙度R_a从亚微米级(0.27μm)改善到超亚微米级(0.04μm)的范围.     

Tool crater wear depth modeling in CBN hard turning

Hard turning has been receiving increased attention because it offers many possible benefits over grinding in machining hardened steel. The wear of cubic boron nitride (CBN) tools, which are commonly used in hard turning, is an important issue that needs to be better understood. For hard turning to be a viable replacement technology, the high cost of CBN cutting tools and the cost of down-time for tool changing must be minimized. In addition to progressive flank wear, microchipping and tool breakage (which lead to early tool failure) are prone to occur under aggressive machining conditions due to significant crater wear and weakening of the cutting edge. The objective of this study is to model the CBN tool crater wear depth (K_T) to guide the design of CBN tool geometry and to optimize cutting parameters in finish hard turning. First, the main wear mechanisms (abrasion, adhesion, and diffusion) in hard turning are discussed and the associated wear volume loss models are developed as functions of cutting temperature, stress, and other process information. Then, the crater wear depth is predicted in terms of tool/work material properties and process information. Finally, the proposed model is experimentally validated in finish turning of hardened 52100 bearing steel using a low CBN content tool. The comparison between model predictions and experimental results shows reasonable agreement, and the results suggest that adhesion is the dominant wear mechanism within the range of conditions that were investigated.     

AN EXPERIMENTAL AND FEM STUDY ON DRY TURNING OF ROTOR STEEL 26NiCrMoV145 USING MULTILAYER COATED CEMENTED CARBIDE TOOL

Rotor steel 26NiCrMoV145 has been widely employed in aerospace and power industry because of its unique properties. As to this new material that is used widely in important places, it is worth studying its machinability. An experiment and finite element (FE) simulation has been carried out to study the cutting forces, cutting temperature and tool wear mechanism during high speed dry turning of 26NiCrMoV145 using multilayer TiCN + Al₂O₃ coated carbide inserts. The orthogonal test was chosen and cutting forces were measured to validate the FE simulations. SEM analysis has been carried out on worn tools to determine the tool wear mechanism. Crater wear and coating peeling could be found at every cutting speed. Flank face wear appears smooth when cutting speed increases. Analyses of tool stress and temperature distribution during simulated cutting process were also taken out to help in understanding tool wear mechanism. At last, an optimization of the cutting conditions was suggested when considering material remove rate, cutting forces and tool wear.     

Cutting forces,tool wear and surface finish in high speed diamond machining

We have investigated the cutting forces, the tool wear and the surface finish obtained in high speed diamond turning and milling of OFHC copper, brass CuZn39Pb3, aluminum AlMg5, and electroless nickel. In face turning experiments with constant material removal rate the cutting forces were recorded as a function of cutting speed between v_c = 150 m/min and 4500 m/min revealing a transition to adiabatic shearing which is supported by FEM simulations of the cutting process. Fly-cutting experiments carried out at low (v_c = 380 m/min) and at high cutting speed (v_c = 3800 m/min) showed that the rate of abrasive wear of the cutting edge is significantly higher at ordinary cutting speed than at high cutting speed in contrast to the experience made in conventional machining. Furthermore, it was found that the rate of chemically induced tool wear in diamond milling of steel is decreasing with decreasing tool engagement time per revolution. High speed diamond machining may also yield an improved surface roughness which was confirmed by comparing the step heights at grain boundaries obtained in diamond milling of OFHC copper and brass CuZn39Pb3 at low (v_c = 100 m/min) and high cutting speed (v_c = 2000 m/min). Thus, high speed diamond machining offers several advantages, let alone a major reduction of machining time.     

3D characterisation of tool wear whilst diamond turning silicon

Nanometrically smooth infrared silicon optics can be manufactured by the diamond turning process. Due to its relatively low density, silicon is an ideal optical material for weight sensitive infrared (IR) applications. However, rapid diamond tool edge degradation and the effect on the achieved surface have prevented significant exploitation. With the aim of developing a process model to optimise the diamond turning of silicon optics, a series of experimental trials were devised using two ultra-precision diamond turning machines. Single crystal silicon specimens (1 1 1) were repeatedly machined using diamond tools of the same specification until the onset of surface brittle fracture. Two cutting fluids were tested. The cutting forces were monitored and the wear morphology of the tool edge was studied by scanning electron microscopy (SEM).The most significant result showed the performance of one particular tool was consistently superior when compared with other diamond tools of the same specification. This remarkable tool performance resulted in doubling the cutting distance exhibited by the other diamond tools. Another significant result was associated with coolant type. In all cases, tool life was prolonged by as much as 300% by using a specific fluid type.Further testing led to the development of a novel method for assessing the progression of diamond tool wear. In this technique, the diamond tools gradual recession profile is measured by performing a series of plunging cuts. Tool shape changes used in conjunction with flank wear SEM measurements enable the calculation of the volumetric tool wear rate.     

Wear of Ceramic Cutting Tools in Ni-Based Superalloy Machining

The machining performance of monolithic and composite silicon nitride and Al₂O₃-based cutting tools in continuous turning of Inconel 718 was examined. The character of tool wear has been found to vary, depending on the feed rate and cutting speeds. At a lower cutting speed, of 120 m/min, tool life is restricted by depth-of-cut notching, while at high cutting speeds (300 m/min), tools fail due to nose wear and fracture. The sensitivity of monolithic Si₃N₄ and Al₂O₃ to depth-of-cut notching was found to he significantly reduced with the addition of SiC whiskers, and to a lesser extent with TiC particulates. The ceramic composites also exhibited resistance to nose and flank wear that was higher than that of the monoliths. The internal stress distribution for the cutting tool has been calculated using the finite element method and is the basis for explaining fracture beneath the rake face. Cutting tool wear results are discussed in terms of chemical and mechanical properties of the ceramic tool material, abrasive wear, thermal shock resistance, and metal cutting conditions.     

Tool wear and its effect on surface roughness in diamond cutting of glass soda-lime

For the technology of diamond cutting of optical glass, the high tool wear rate is a main reason for hindering the practical application of this technology. Many researches on diamond tool wear in glass cutting rest on wear phenomenon describing simply without analyzing the genesis of wear phenomenon and interpreting the formation process of tool wear in mechanics. For in depth understanding of the tool wear and its effect on surface roughness in diamond cutting of glass, experiments of diamond turning with cutting distance increasing gradually are carried out on soda-lime glass. The wear morphology of rake face and flank face, the corresponding surface features of workpiece and the surface roughness, and the material compositions of flank wear area are detected. Experimental results indicate that the flank wear is predominant in diamond cutting glass and the flank wear land is characterized by micro-grooves, some smooth crater on the rake face is also seen. The surface roughness begins to increase rapidly, when the cutting mode changes from ductile to brittle for the aggravation of tool wear with the cutting distance over 150 m. The main mechanisms of inducing tool wear in diamond cutting of glass are diffusion, mechanical friction, thermo-chemical action and abrasive wear. The proposed research makes analysis and research from wear mechanism on the tool wear and its effect on surface roughness in diamond cutting of glass, and provides theoretical basis for minimizing the tool wear in diamond cutting brittle materials, such as optical glass.     

Environmentally conscious hard turning of cemented carbide materials on the basis of micro-cutting in SEM (2nd report): stress turning with three kinds of cutting tools

Environmentally conscious hard turning and technology have placed increasing importance on the machining process. Cutting fluids have a significant impact on the environment, thus numerous research works are being performed to minimize their use. However, tool wear is very severe in hard turning cemented carbides without the use of cutting fluids. In this research, the effects of dry and wet cutting methods (vegetable oil mist and mineral oil) and tool material on cutting resistance and wear characteristics of cutting tools were experimentally investigated to study the possibility of creating an environmentally conscious hard turning of cemented carbides. Mist and wet cutting of the cemented carbides using poly-crystalline diamond (PCD) cutting tools were adopted to investigate how tool wear on the basis of micro-cutting in the Scanning Electron Microscope (SEM) can be reduced. Additionally, the poly-crystalline cubic boron nitride (PcBN) and the usual cBN cutting tools were compared with the PCD cutting tools. This paper was presented at the 9^th Asian International Conference on Fluid Machinery (AICFM9), Jeju, Korea, October 16–19, 2007.recommended for publication in revised form by Associate Editor Dae-Eun Kim HEO Sung Jung was born in Busan, R. O. K., in 1958. He received the Ph.D. in Mechanical Engineering from Osaka University, Osaka, Japan. He is a Full Professor of Mechanical Engineering at Doowon Technical College, Ansong -si, Gyonggi-do, Republic of Korea. His current research interests are in the areas of cutting of difficult-to-cut materials, environmentally conscious machining and cutting tool design.     

Experimental assessment of textured tools with nano-lubricants in orthogonal cutting of titanium alloy

In this study, we investigated the effects of composite nano-Cu/WS₂ lubricating oil and single-point diamond indentation-textures on improving the cutting performance of YG8 cemented carbide tools, which is crucial for textures tool applications. The aims of the study were to improve wear resistance and reduce chip adhesion at the tool’s rake face in cutting of titanium alloys. Dot textures with different spacings were fabricated on the surface of YG8 cemented carbide tools through the single-point diamond indentation method, and composite nano-Cu/WS₂ lubricating oil was prepared. Orthogonal cutting tests were carried out under dry cutting and minimal quantity lubricated (MQL) conditions. Investigate the effect of different texture spacing on the cutting performance in the light of cutting forces, friction coefficient, the deformed chip thickness, tool adhesions, and chip morphology. The results show that the dot texture effectively improved the lubrication conditions in machining titanium alloys under the MQL conditions. The dot texture is effective at low speed in the dry cutting conditions. With the increase of cutting speed, the friction coefficient of dot texture tool is affected by texture spacing, and the friction coefficient of DT-200 tool is the smallest. In addition, composite nano Cu/WS₂ lubricating oil forms a lubricating film on the wear path by atomizing the lubricating oil and stores it in the dot texture, which enhances the anti-wear performance in the cutting process and reduces the cutting force and friction coefficient at the tool chip interface. By evaluating cutting force, friction coefficient, chip and tool morphology, it is concluded that DT-100 tool is more effective in improving lubrication conditions.

     

A comparative study of multilayer and functionally graded coated tools in high-speed machining

Multilayer-coated tool systems have been effective in controlling mechanical and thermal loads, especially in high-speed cutting regime. In this study, cutting performance of tungsten carbide tools with restricted contact length and multilayer chemical vapour deposition deposited coatings, TiCN/Al₂O₃/TiN (in series) and TiCN/Al₂O₃–TiN (functionally graded), was investigated in dry turning. Cutting tests were conducted on low carbon alloy steel AISI/SAE 4140 over a wide range of cutting speeds between 200 and 879?m/min. Results including cutting forces, chip compression ratio, shear angle, contact area inclusive of sticking and sliding phenomena and tool flank wear are presented. In particular, prediction of heat partition into the cutting tool inserts was carried out using a combination of experimental tests and the finite element method. The results show that coating layouts and cutting tool edge geometry can significantly affect heat distribution into the cutting tool. The paper clearly shows the role and potential benefits of applying different top coats on the rake and flank faces with regards contact phenomenon, impact on thermal shielding and tool wear. An appropriate coating layout selection is crucial in controlling tool wear, especially in high-speed machining.     

Investigation and prediction of chip geometry in diamond turning

Management of the chips generated in diamond turning is often critical, because contact between chips and the workpiece can result in superficial damage to the finished surface. Controlling chip motion is not a trivial process as the proper positioning of an oil or air stream requires an understanding of the dynamics of a diamond turned chip and the machining parameters that affect it. Work has been performed to investigate the effects of cutting speed, depth of cut, tool geometry, tool wear, and workpiece material properties on chip motion and geometry. Utilizing radius of curvature data from cutting experiments, a parameter has been proposed that can be used to predict chip radius of curvature for a wide range of machining conditions. This chip curvature parameter, χ, exhibits a power law relationship with chip radius of curvature as a function of tool geometry, depth of cut, cutting speed, and both elastic and plastic properties of the workpiece material.     

An investigation on wear mechanism of high-speed turning of free-cutting steel AISI 1215 using uncoated and multi-layer coated tools

AISI 1215 is a new kind of green and non-toxic free-cutting steel with minimum environmental pollution and excellent machinability, which receives wide promotion, investigation, and application in manufacturing industries. In machining of AISI 1215 steel, tool wear has a close relation with the presence of manganese sulfide lubricant zone formed on the tool surface. In this work, with the aid of cutting temperature and tool Von Mises stress simulations, tool wear analysis on the uncoated and multi-layer (Al₂O₃/TiCN) coated carbide tools was performed in high-speed turning operation. Wear pattern and wear mechanisms were studied through the experimental results. The main findings showed that the uncoated tool suffered high cutting temperature and severe tool wear and was not conducive to form a manganese sulfide lubricant zone in the turning operation. In contrast, the multi-layer coated tool could form a manganese sulfide lubricant zone on the chip–tool contact area. The beneficial roles of the manganese sulfide lubricant zone formed on the coated tool surface can be summarized as lubrication and diffusion blocking. The main wear mechanisms of the uncoated tool were crater wear, oxidation wear, adhesive wear, and abrasive wear, whereas for the multi-layer coated tool, they were crater wear, adhesive wear, and abrasive wear.     

Suppression of tool damage in ultraprecision diamond machining of stainless steel by applying electron-beam-excited plasma nitriding

Mirror surface machining of stainless steel with single-crystalline diamond tools is proposed in this study by applying a new nitriding method, called electron-beam-excited-plasma (EBEP) nitriding, to workpiece surfaces as pretreatment. It is well known that mirror surface finish of steel workpieces by conventional diamond cutting is unachievable owing to rapid tool wear. Nitriding of steel workpieces has been one of the several attempts to prevent the rapid tool wear of diamond tools. It has been reported that the rapid tool wear is caused by thermochemical interaction between diamond and steel, and that the wear can be greatly reduced by nitriding of steel. However, hard compounds formed on the outmost surfaces of workpieces by the conventional nitriding methods can cause micro-chippings of cutting tools. The authors has recently developed a new nitriding method called EBEP nitriding, in which a high dissociation rate for nitrogen molecules is achieved using the electron-beam-excited-plasma, and iron-compounds-free nitriding has been realized. Therefore, the EBEP nitriding is applied to a typical mold material, modified AISI 420 stainless steel, aiming at suppressing the micro-chippings as well as the thermochemical tool wear during diamond cutting of the stainless steel. The conventional ion nitriding and the gas nitrocarburizing are also applied to the same stainless steel in comparison. Chemical components of the nitrided workpiece surfaces are analyzed by an electron prove micro-analyzer (EPMA) and an X-ray diffraction (XRD) in advance, and turning experiments are conducted with single-crystalline diamond tools. Subsequently, changes in cutting forces and roughness of finished surfaces and tool damages after the turning experiments are evaluated. Finally, mirror surface machining by using the EBEP nitriding is demonstrated, and its advantages and disadvantages in the diamond cutting of stainless steel are summarized in comparison with the conventional nitriding methods.     

Performance of ceramic tools in high-speed cutting iron-based superalloys

A series of turning tests were conducted to investigate the cutting performance of ceramic tools in high-speed turning iron-based superalloys GH2132 (A286). Three kinds of ceramic tools, KY1540, CC650, and CC670 were used and their materials are Sialon, Al₂O₃–Ti(C,N), and Al₂O₃–SiC_w, respectively. The cutting forces, cutting temperatures, tool wear morphologies, and tool failure mechanisms are discussed. The experimental results show that with the increase in cutting speed, the resultant cutting forces with KY1540 and CC670 tools show a tendency to increase first and then decrease while those for CC650 increase gradually. The cutting temperature increases monotonically with the increase in cutting speed. The optimum cutting speeds for KY1540 and CC650 when turning GH2132 are less than 100 m/min, while those for CC670 are between 100 and 200 m/min. Flank wear is the main reason that leads to tool failure of KY1540 and CC670 while notch wear is the main factor that leads to tool failure of CC650. Tool failure mechanisms of ceramic tools when machining GH2132 include adhesion, chipping, abrasion, and notching. Better surface roughness can be got using CC670 ceramic tools.     

Cutting force and tool wear of single diamond-coated bead

The aim of this study is to optimize stone materials cutting by diamond wire cutter. Attention is focused on the study of the cutting process through sintered diamond-encrusted beads used to work granite. This study is aimed at understanding the interaction between the bead and the material; in detail, experimental equipment was designed to test individual diamond-coated beads, and it was installed on a numerical-control work center. This equipment made it possible to test an individual bead and, in particular, to determine its cutting power and its main force components on the basis of various process parameters, such as cutting velocity (V _t) and feed velocity (V _a). The test runs also made it possible to determine wear on each bead on the basis of process parameters. This is a necessary first step to be able, in the future, to optimize the tool and the cutting process.     

Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts

The present work deals with some machinability studies on flank wear, surface roughness, chip morphology and cutting forces in finish hard turning of AISI 4340 steel using uncoated and multilayer TiN and ZrCN coated carbide inserts at higher cutting speed range. The process has also been justified economically for its effective application in hard turning. Experimental results revealed that multilayer TiN/TiCN/Al₂O₃/TiN coated insert performed better than uncoated and TiN/TiCN/Al₂O₃/ZrCN coated carbide insert being steady growth of flank wear and surface roughness. The tool life for TiN and ZrCN coated carbide inserts was found to be approximately 19 min and 8 min at the extreme cutting conditions tested. Uncoated carbide insert used to cut hardened steel fractured prematurely. Abrasion, chipping and catastrophic failure are the principal wear mechanisms observed during machining. The turning forces (cutting force, thrust force and feed force) are observed to be lower using multilayer coated carbide insert in hard turning compared to uncoated carbide insert. From 1st and 2nd order regression model, 2nd order model explains about 98.3% and 86.3% of the variability of responses (flank wear and surface roughness) in predicting new observations compared to 1st order model and indicates the better fitting of the model with the data for multilayer TiN coated carbide insert. For ZrCN coated carbide insert, 2nd order flank wear model fits well compared to surface roughness model as observed from ANOVA study. The savings in machining costs using multilayer TiN coated insert is 93.4% compared to uncoated carbide and 40% to ZrCN coated carbide inserts respectively in hard machining taking flank wear criteria of 0.3 mm. This shows the economical feasibility of utilizing multilayer TiN coated carbide insert in finish hard turning.     

Precision milling of high volume fraction SiCp/Al composites with monocrystalline diamond end mill

Silicon carbide particle-reinforced aluminum matrix (SiC_p/Al) composites have attracted considerable interest as potential materials due to their excellent engineering properties. Many research works have been done associated with turning SiC_p/Al in the past. However, it still lacks of experience on milling of SiC_p/Al composites. This paper presents an exploratory study on precision milling of SiC_p/Al composites with higher volume fraction (SiC_p, 65 %) and larger particle size. The experiments were conducted on a Kern MMP 2522, high-precision micromilling machine center. A single flute monocrystalline diamond end mill was used to mill straight grooves with cutting parameters in a few micros. The machined surface quality including surface roughness and surface topography were studied. The cutting mechanisms of SiC particle and tool wear characters were also investigated. The results showed that mirror-like surface with surface roughness around 0.1 μm Ra can be achieved by precision milling with small parameters in the range of a few micros. Most of the SiC reinforcements were cut in partial ductile way with microfractures and cracks on the machined surface; tool wear included chipping and cleavage on monocrystalline diamond edge. A large flank wear on tool bottom face was observed and suspected to be caused by coaction of chemical transition and mechanical abrasion.     

Single-point diamond turning of CaF2 for nanometric surface

Single-crystal CaF₂ is an important optical material. In this work, single-point diamond turning experiments were performed to investigate the nanometric machining characteristics of CaF₂. The effects of tool feed, tool rake angle, workpiece crystal orientation and cutting fluid were examined. It was found that two major types of microfracturing differing in mechanism limited the possibility of ductile regime machining. The critical conditions for microfracturing depend strongly on the tool rake angle and the type of cutting fluid. The results also indicate that one type of the microfractures is caused by thermal effect, and can be completely eliminated by using a sufficiently small undeformed chip thickness and an appropriate negative rake angle under dry cutting conditions. Continuous chips and ductile-cut surfaces with nanometric roughness were generated.     

Competitive parameter optimization of multi-quality CNC turning

Surface roughness, tool wear, and material removal rate (MRR) are major intentions in the modern computer numerical controlled (CNC) machining industry. In this paper, the ${\text{L}}_9 \left( {3^4 } \right)$ orthogonal array of a Taguchi experiment is selected for four parameters (cutting depth, feed rate, speed, and tool nose runoff) with three levels (low, medium, and high) in optimizing the finish turning parameters on an ECOCA-3807 CNC lathe. The surface roughness (R_a) and tool wear ratio (mm^?2) are primarily observed as independent objectives for developing two combinations of optimum single-objective cutting parameters. Additionally, the levels of competitive orthogonal array are then proposed between the two parameter sets. Therefore, the optimum competitive multi-quality cutting parameters can then be achieved. Through the machining results of the CNC lathe, it is shown that both tool wear ratio and MRR from our optimum competitive parameters are greatly advanced with a minor decrease in the surface roughness in comparison to those of benchmark parameters. This paper not only proposes a competitive optimization approach using orthogonal array, but also contributes a satisfactory technique for multiple CNC turning objectives with profound insight.     

A step towards the in-process monitoring for electrochemical microdrilling

The bandsawing as a multi-point cutting operation is the preferred method for cutting off raw materials in industry. Although cutting off with bandsaw is very old process, research efforts are very limited compared to the other cutting process. Appropriate online tool condition monitoring system is essential for sophisticated and automated machine tools to achieve better tool management. Tool wear monitoring models using artificial neural network are developed to predict the tool wear during cutting off the raw materials (American Iron and Steel Institute 1020, 1040 and 4140) by bandsaw. Based on a continuous data acquisition of cutting force signals, it is possible to estimate or to classify certain wear parameters by means of neural networks thanks to reasonably quick data-processing capability. The multi-layered feed forward artificial neural network (ANN) system of a 6?×?9?×?1 structure based on cutting forces was trained using error back-propagation training algorithm to estimate tool wear in bandsawing. The data used for the training and checking of the network were derived from the experiments according to the principles of Taguchi design of experiments planned as L ₂₇. The factors considered as input in the experiment were the feed rate, the cutting speed, the engagement length and material hardness. 3D surface plots are generated using ANN model to study the interaction effects of cutting conditions on sawblade. The analysis shows that cutting length, hardness and cutting speed have significant effect on tooth wear, respectively, while feed rate has less effect. In this study, the details of experimentation and ANN application to predict tooth wear have been presented. The system shows that there is close match between the flank wear estimated and measured directly.