Effects of alkali and silane treatment on the mechanical properties of jute‐fiber‐reinforced recycled polypropylene composites

Jute‐fibers‐reinforced thermoplastic composites are widely used in the automobile, packaging, and electronic industries because of their various advantages such as low cost, ease of recycling, and biodegradability. However, the applications of these kinds of composites are limited because of their unsatisfactory mechanical properties, which are caused by the poor interfacial compatibility between jute fibers and the thermoplastic matrix. In this work, four methods, including (i) alkali treatment, (ii) alkali and silane treatment, (iii) alkali and (maleic anhydride)‐polypropylene (MAPP) treatment, and (iv) alkali, silane, and MAPP treatment (ASMT) were used to treat jute fibers and improve the interfacial adhesion of jute‐fiber‐reinforced recycled polypropylene composites (JRPCS). The mechanical properties and impact fracture surfaces of the composites were observed, and their fracture mechanism was analyzed. The results showed that ASMT composites possessed the optimum comprehensive mechanical properties. When the weight fraction of jute fibers was 15%, the tensile strength and impact toughness were increased by 46 and 36%, respectively, compared to those of untreated composites. The strongest interfacial adhesion between jute fibers and recycled polypropylene was obtained for ASMT composites. The fracture styles of this kind of composite included fiber breakage, fiber pull‐out, and interfacial debonding. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers.     

Preparation and mechanical properties of high‐performance short ramie fiber‐reinforced polypropylene composites

Short ramie fiber (RF) was used to reinforce the polypropylene (PP). The composites were prepared in a twin‐screw extruder followed by injection molding. The experimental results showed that both the strength and the modulus of the composites increase considerably with increasing RF content. The tensile strength and flexural strength are as high as 67 and 80 MPa by the incorporation of ramie up to 30 wt %. To the best of our knowledge, this is one of the best results for short natural fiber‐reinforced PP composites. However, the preparation method in this study is more simple and economic. This short RF‐reinforced PP composites extend the application field for short‐nature fiber‐reinforced PP composites. Morphological analysis revealed that it is the high aspect ratio of the fiber and good interfacial compatibility that result in the high performance of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of sizing materials on the properties of carbon fiber‐reinforced polyamide 6,6 composites

This article aims to study the effect of the sizing materials type on the mechanical, thermal, and morphological properties of carbon fiber (CF)‐reinforced polyamide 6,6 (PA 6,6) composites. For this purpose, unsized CF and sized CFs were used. Thermogravimetric analysis was performed, and it has been found that certain amounts of polyurethane (PU) and PA sizing agents decompose during processing. The effects of sizing agent type on the mechanical and thermomechanical properties of all the composites were investigated using tensile, Izod impact strength test, and dynamic mechanical analysis. Tensile strength values of sized CF‐reinforced composites were higher than that of unsized CF‐reinforced composites. PA and polyurethane sized CF‐reinforced composites exhibited the highest impact strength values among the other sized CF‐reinforced composites. PU and PA sized CF‐reinforced composites denoted higher storage modulus and better interfacial adhesion values among the other sizing materials. Scanning electron microscope studies indicated that CFs which were sized with PU and PA have better interfacial bonding with PA 6,6 matrix among the sized CFs. All the results confirmed that PA and PU were suitable for CF's sizing materials to be used for PA 6,6 matrix. POLYM. COMPOS., 34:1583–1590, 2013. © 2013 Society of Plastics Engineers     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Short jute fiber‐reinforced polypropylene composites: Dynamic mechanical study

Short jute fiber‐reinforced polypropylene (PP) composites were prepared using a high‐speed thermokinetic mixer. A compatibilizer was used to improve the molecular interaction between jute and PP. Both the percent weight fraction of the jute fiber and compatibilizer were varied to study the dynamic mechanical thermal (DMT) properties. Dynamic parameters such as storage flexural modulus (E′), loss flexural modulus (E″), storage shear modulus (G′), loss shear modulus (G″), and loss factor or damping efficiency (tan δ) were determined in a resonant frequency mode. The transition peak nature, amplitude, and temperature of E′, E″, G′, G″, and tan δ of different compositions were shown to indicate possible improvements of molecular interaction in the presence of a compatibilizer. The modulus retention term, a plot of the reduced modulus with the weight fraction of the jute fiber, also indicate its improvement. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 531–539, 1999     

Mechanical properties and viscoelastic behavior of basalt fiber‐reinforced polypropylene

In the present article, a series of commercial‐grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene‐g‐maleic anhydride) (PP‐g‐MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP‐g‐MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP‐g‐MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP‐g‐MA content. With increasing fiber content, damping in the β‐region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the α‐relaxation process of PP. The position of the peaks of the above‐mentioned relaxation processes are discussed as well. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 523–531, 1999     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

Moisture absorption properties of wood‐fiber‐reinforced recycled polypropylene matrix composites

To reduce the moisture absorption of wood‐fiber‐reinforced recycled plastic composites (WRPCs), a coupling agent (KH550), methyl methacrylate (MMA), and maleic anhydride (MA) were used to modify the wood fibers. The surface‐treated wood fibers were mixed with recycled polypropylene and processing agents to fabricate the WRPCs. The mechanical properties and moisture absorption behavior of the WRPCs were determined. The results showed that the three surface treatment methods could effectively reduce the moisture absorption and thickness swelling of WRPCs. In Comparison to the properties of untreated wood‐fiber‐reinforced WRPCs, the moisture absorption ratio of WRPCs with wood fibers treated by MMA, KH550, and MA was reduced by 31.4%, 49.8%, and 38.2%, respectively, and the tensile strength was increased by 22.1%, 26.3%, and 4.2%, respectively. The impact toughness of the WRPCs was increased by 36.2% KH550 treatment and 19.2% for MMA treatment but was decreased by 4.2% for MA treatment. Coupling treatment of the wood fibers was the best way to reduce the moisture absorption of WRPCs, and this kind of WRPC possessed the best comprehensive properties. J. VINYL ADDIT. TECHNOL., 2010. © 2009 Society of Plastics Engineers     

Influence of thermooxidative aging on the static and dynamic mechanical properties of long‐glass‐fiber‐reinforced polyamide 6 composites

The static and dynamic mechanical properties, thermal behaviors, and morphology of pure long‐glass‐fiber‐reinforced samples [polyamide 6 (PA6)/long glass fiber (LGF)] with different thermal exposure times at 160°C were studied by comparison with stabilized samples in this study. The aging mechanism of the PA6/LGF samples under heat and oxygen was studied with the methods of thermal Fourier transform infrared (FTIR), differential scanning calorimetry, dynamic mechanical analysis, scanning electron microscopy (SEM), and so on. The results indicate that the static mechanical strength, melting temperature, and crystallization temperature decreased because of the decomposition of the macromolecular chain of PA6 resin and the debonding of the interface between the glass fibers and matrix. The glass‐transition temperature and crystallinity also increased and decreased, respectively, after aging. The macromolecular chain decomposition dominated in the subsequent aging process; this resulted in many sharp and brittle microcracks appearing on the surfaces of the aged samples, as shown by SEM and the FTIR spectra. The existence of stabilizers endowed the PA6/LGF composites with better retention of static and dynamic mechanical properties. The reason was that the metal ions of the copper salt antioxidant acted as an anti‐aging catalyst in the reinforced PA6 system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39594.     

A comparative study on mechanical properties and water absorption behavior of fiber‐reinforced polypropylene composites prepared by OCC fiber and aspen fiber

Fiber‐reinforced polymers have received considerable attention from industry in recent years. Due to the sharp ecological damage, worldwide shortage of trees in many areas and the global demand for fibrous material, there has been growing interest in the use of recycled wood fiber as an alternative or substitute fiber source. The present study investigates the tensile, flexural, Izod impact, and water absorption behavior of Old Corrugated Container (OCC) and aspen (AS) reinforced polypropylene (PP) composites as a function of fiber content. The surface of AS and OCC fibers was modified through the use of MAPP coupling agent. From the studies it was found that mechanical properties increase with increase in fiber loading in both cases. However the addition of wood fibers resulted in a decrease in impact strength of the composites. The water absorption property at varying fiber loading were evaluated and found maximum for the OCC/PP composites. The weight gains for all specimens were less than 3.5%. Finally, the results showed the usefulness of OCC fiber as a good alternative and reinforcing agent for composite. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Effect of maleic anhydride grafted polypropylene on the mechanical and morphological properties of chemically modified short‐pineapple‐leaf‐fiber‐reinforced polypropylene composites

With the rising cost of petroleum‐based fibers, the utilization of plant fibers in the manufacture of polymer–matrix composites is gaining importance worldwide. The scope of this study was to examine the perspective of the use of pineapple leaf fibers (PALFs) as reinforcements for polypropylene (PP). These fibers are environmentally friendly, low‐cost byproducts of pineapple cultivation and are readily available in the northeastern region of India. Here, both untreated and treated pineapple fibers were used. Maleic anhydride grafted polypropylene (MA‐g‐PP) was used as a compatibilizing agent. The polymer matrix of PP was used to prepare composite specimens with different volume fractions (5–20%) of fibers by the addition of 5% of MA‐g‐PP. These specimens were tested for their mechanical properties, and additional assessments were made via observations by scanning electron microscopy, thermogravimetric analysis, and IR spectroscopy. Increase in the impact behavior, flexural properties, and tensile moduli of the composites were noticed, and these were more appreciable in the treated fibers mixed with MA‐g‐PP. PALF in 10 vol % in PP mixed with MA‐g‐PP was the optimum and recommended composition, where the flexural properties were the maximum. The impact strength and the tensile modulus were also considerably high. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fabrication and properties of nano‐ZnO/glass‐fiber‐reinforced polypropylene composites

Polypropylene (PP) is widely used in many fields, such as automobiles, medical devices, office equipment, pipe, and architecture. However, its high brittle transformation temperature, low mechanical strength, dyeing properties, antistatic properties, and poor impact resistance, considerably limit its further applications. Nano‐ZnO treated by KH550 coupling agent and glass fibers (GFs) were introduced in order to improve the mechanical performance and flowability of PP in this research. The crystallization behavior and microstructure of nano‐ZnO/GFs/PP hybrid composites were analyzed by differential scanning calorimetry, transmission electron microscopy, and scanning electron microscopy. The effect of crystallization behavior on the mechanical properties of the nanocomposites was investigated and analyzed. The results indicated that nano‐ZnO surface‐coupled by KH550 could be uniformly dispersed in the PP matrix. The incorporation of nano‐ZnO and GFs resulted in increases of the crystallization temperature and crystallization rate of PP and a decrease of the crystallization degree. The introduction of nano‐ZnO and GFs also enhanced the tensile strength and impact toughness of the hybrid composites and improved their fluidity. Composites containing 2% of nano‐ZnO and 40% of GFs possessed the optimum mechanical properties. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Crystallization,mechanical, and fracture behavior of mullite fiber‐reinforced polypropylene nanocomposites

This study describes the reinforcement effect of surface modified mullite fibers on the crystallization, thermal stability, and mechanical properties of polypropylene (PP). The nanocomposites were developed using polypropylene‐grafted‐maleic anhydride (PP‐g‐MA) as compatibilizer with different weight ratios (0.5, 1.0, 1.5, 2.5, 5.0, and 10.0 wt %) of amine functionalized mullite fibers (AMUF) via solution blending method. Chemical grafting of AMUF with PP‐g‐MA resulted in enhanced filler dispersion in the polymer as well as effective filler‐polymer interactions. The dispersion of nanofiller in the polymer matrix was identified using scanning electron microscopy (SEM) elemental mapping and transmission electron microscopy (TEM) analysis. AMUF increased the Young's modulus of PP in the nanocomposites up to a 5 wt % filler content, however, at 10 wt % loading, a decrease in the modulus resulted due to agglomeration of AMUF. The impact strength of PP increased simultaneously with the modulus as a function of AMUF content (up to 5 wt %). The mechanical properties of PP‐AMUF nanocomposites exhibited improved thermal performance as compared to pure PP matrix, thus, confirming the overall potential of the generated composites for a variety of structural applications. The mechanical properties of 5 wt % of AMUF filled PP nanocomposite were also compared with PP nanocomposites generated with unmodified MUF and the results confirmed superior mechanical properties on incorporation of modified filler. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43725.     

Moisture absorption behavior and its effect on the mechanical properties of jute‐reinforced epoxy composite

With the growing economic competition and the ecological pressure, the past decade has seen a renewed interest in developing more efficient reinforcements along with overall production cost. In some industrial applications, natural fiber composites fulfill small requirements for making the product to be economical due to their several advantages such as low density, greater deformability, lower abrasiveness, and cost. In the present work, composites are prepared with epoxy as a resin and jute as reinforcement by hand lay‐up technique. Moisture absorption characteristics when exposed to saline water, mineral water, sub‐zero temperature conditions, and also effect of moisture on depreciation in strength (tensile strength and flexural strength) and of different layers (one, two, three layers) of composites are studied experimentally. Specimen preparation and testing were carried out as per ASTM standards. It is found that the jute‐reinforced epoxy composite give encouraging results when compared with the pure epoxy composites. The less effect in strength is observed after exposure to mineral water and sub‐zero temperature condition. The morphologies of the composites are also studied by scanning electron microscope. POLYM. COMPOS., 38:516–522, 2017. © 2015 Society of Plastics Engineers     

Localized thermal analysis of carbon fiber‐reinforced polypropylene composites

The effect of carbon fiber (CF) and annealing temperature on polypropylene (PP) microstructure was studied. The crystalline state of polymer matrix was found to be a strong function of thermal history. The effect of annealing temperature on the microstructure evolution of PP in the presence of CFs was characterized by using X‐ray diffraction, DSC and localized thermal analysis. The melting behavior of CF‐reinforced PP composite was strongly dominated by the thermal history and was weakly influenced by the presence of CFs. The interface between a CF and PP matrix was found to be weak. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Fabrication and mechanical properties of glass fiber‐reinforced wood plastic hybrid composites

To fully utilize the resource in the municipal solid waste (MSW) and improve the strength and toughness of wood plastic composites, glass fiber (GF)‐reinforced wood plastic hybrid composites (GWPCs) were prepared through compounding of recycled high‐density polyethylene (HDPE) from MSW, waste wood fibers, and chopped GF. Mechanical tests of GWPCs specimens with varying amounts of GF content were carried out and the impact fractured surface of GWPCs was observed through scanning electron microscope (SEM). The tensile strength of GWPCs and the efficiency coefficient values were predicted by Kelly‐Tyson method. The results indicated that the tensile strength and impact strength of GWPCs could be improved simultaneously by adding type L chopped GF (L‐GF), and would be dropped down when type S chopped GF (S‐GF) was included. The tensile strength of GWPCs was well accordant with the experimental result. The efficiency coefficient values of S‐GF and L‐GF are ?0.19 and 0.63, respectively. Inspection of SEM micrographs indicated that L‐GF had achieved full adhesion with the plastic matrix through addition of maleic anhydride‐g‐polyethylene. The main fracture modes of GWPCs included pullout of GF, broken of matrix, and interfacial debonding. Because of the synergistic effects between hybrid components in GF/wood fiber/HDPE hybrid system, a special 3D network microstructure was formed, which was the main contribution to the significant improvement in the tensile strength and impact strength of L‐GF‐reinforced hybrid composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Influence of functionalized polyolefin on interfacial adhesion of glass fiber‐reinforced polypropylene

Several types of functionalized polyolefins, grafted with maleic anhydride, were synthesized and used to modify the surface of fiberglass in reinforced polypropylene composites. The influence of maleated polyolefin, matrix, and compounding conditions on the interfacial bonding strength of composite were studied by measuring interfacial shear strength. The results showed that strong interactions, e.g., chemical bonding, were formed between maleated polyolefin and fiber surface. When the modified fibers were compounded with polypropylene, firm entanglements of molecular chain were formed due to the segmental interdiffusion between maleated polyolefin and matrix polypropylene. As a result, the degree of fiber‐matrix adhesion was improved. The extent of such improvement depended on the grafting degree, chain length of maleated polyolefin, and the compatibility between maleated polyolefin and matrix resin. At the same time, the compounding temperature and the cooling procedure affected the interfacial adhesion too. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1359–1365, 2000     

Short sisal fiber‐reinforced tire rubber composites: Dynamic and mechanical properties

The world tendency toward using recycled materials demands new products from vegetable resources and waste polymers. In this work, composites made from powdered tire rubber (average particle size: 320 μm) and sisal fiber were prepared by hot‐press molding and investigated by means of dynamic mechanical thermal analysis and tensile properties. The effects of fiber length and content, chemical treatments, and temperature on dynamic mechanical and tensile properties of such composites were studied. The results showed that mercerization/acetylation treatment of the fibers improves composite performance. Under the conditions investigated the optimum fiber length obtained for the tire rubber matrix was 10 mm. Storage and loss moduli both increased with increasing fiber content. The results of this study are encouraging, demonstrating that the use of tire rubber and sisal fiber in composites offers promising potential for nonstructural applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 670–677, 2004     

Carbon fiber‐reinforced gelatin composites. I. Preparation and mechanical properties

Composites were made from carbon fibers and gelatin using a solvent‐casting or solution‐impregnation technique. Relationships between the fiber volume fraction (Vf), glycerol (plasticizer) content, gelatin content, fiber form, and mechanical properties (tensile strength and modulus, elongation at break, and shear strength) of the composites were investigated. In long carbon fiber gelatin composite (C_L/Gel), tensile strength, modulus, and shear strength increased steadily with the Vf. In the case of a short carbon fiber gelatin composite (C_S/Gel), an initial improvement in tensile strength and modulus was followed by a reduction, whereas the shear strength improved with the Vf and then reached a constant value. The elongation decreased with the Vf for both composites. It is shown that C_L/Gel had higher values of strength, modulus, and elongation than did C_S/Gel at any Vf level. The effects of glycerol and gelatin contents on the mechanical properties of the composites were found to be much less significant as compared to the Vf. According to scanning electron microscopic observation of the fracture surfaces, the fibers were uniformly distributed in the gelatin matrix, but the interfacial adhesion between the gelatin matrix and the carbon fibers was not very good for both composites. Fiber surface modification would be necessary to further improve the mechanical properties of the two composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 987–993, 2000     

Recycled‐disposable‐chopstick‐fiber‐reinforced polypropylene green composites

The utilization of disposable chopsticks is very popular in Taiwan, China, and Japan and is one of the major sources of waste in these countries. In this study, recycled disposable chopstick fiber was chemically modified. Subsequently, this modified fiber and polypropylene‐graft‐maleic anhydride were added to polypropylene (PP) to form novel fiber‐reinforced green composites. A heat‐deflection temperature (HDT) test showed an increase of approximately 81% for PP with the addition of 60‐phr fibers, and the HDT of the composite could reach up to 144.8°C. In addition, the tensile strength, Young's modulus, and impact strength were 66, 160.3, and 97.1%, respectively, when the composite material was 40‐phr fibers. Furthermore, this type of reinforced PP would be more environmentally friendly than an artificial‐additive‐reinforced one. It could also effectively reduce and reuse the waste of disposable chopsticks and lower the costs of the materials. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012