Microstructure and mechanical properties of C–Si–Mn(–Nb) TRIP steels after simulated thermomechanical processing

Abstract

Continuous and discontinuous cooling tests were performed using a quench deformation dilatometer to develop a comprehensive understanding of the structural and kinetic aspects of the bainite transformation in low carbon TRIP (transformation induced plasticity) steels as a function of thermomechanical processing and composition. Deformation in the unrecrystallised austenite region refined the ferrite grain size and increased the ferrite and bainite transformation temperatures for cooling rates from 10 to 90 K s^-1. The influence of niobium on the transformation kinetics was also investigated. Niobium increases the ferrite start transformation temperature, refines the ferrite microstructure, and stimulates the formation of acicular ferrite. The effect of the bainite isothermal transformation temperature on the final microstructure of steels with and without a small addition of niobium was studied. Niobium promotes the formation of stable retained austenite, which influences the mechanical properties of TRIP steels. The optimum mechanical properties were obtained after isothermal holding at 400°C in the niobium steel containing the maximum volume fraction of retained austenite with acicular ferrite as the predominant second phase.     

Effect of austenite grain size on isothermal bainite transformation in low carbon microalloyed steel

Abstract

The effect of austenite grain size on isothermal bainite transformation in a low carbon microalloyed steel was studied by means of optical microscopy, SEM and TEM. Two widely varying austenite grain sizes, a fine average grain size (～20 μm) and a coarse average grain size (～260 μm), were obtained by different maximum heating temperatures. The results showed that the morphology of isothermal microstructure changes from bainite without carbide precipitation to bainitic ferrite with a decrease in holding temperature. Coarse austenite grain can retard the kinetics of bainite transformation and increase the incubation time of bainite transformation by reducing the number of nucleation site, but it does not influence the nose temperature of the C curve of bainite start transformation, which is ～534°C.     

Transformation of austenite remaining after intercritical rolling to ferrite

Abstract

The impact of austenite deformation in the intercritical range on the rate of transformation in continuous cooling to ferrite, pearlite, bainite or martensite has been studied. The austenite associated with the rolled ferrite is much higher in carbon content, which does not influence the pearlite transformation but retards bainite and martensite. Furthermore, in comparison with rolling of stable austenite the increased strain hardening of the intercritically cooled austenite accelerates the formation of ferrite and pearlite (+ 10–30°C) and refines them but retards the bainite and martensite transformations (?20–40°C). At the intermediate cooling rate near 16 K s^?1, these several influences combined with near doubling of the ferrite production give rise to the suppression of bainite formation and to maximum increased delay of martensite start.     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.     

Effect of pearlite morphology on impact toughness of eutectoid steel containing vanadium

Abstract

The effect of a change in the morphology of the pearlite colonies on the Charpy impact energy of a fully pearlitic steel containing 0·76%C, 1·20%Mn, and 0·085% V was examined over the range of testing temperatures from ?50 to 200°C. The change from a multicolony nodular pearlite structure produced from austenite of grain size 185 μm to a structure composed of individually formed colonies produced from austenite of grain size 25 μm caused a decrease in the transition temperature of 75 K and an almost 100% increase in the Charpy impact energy measured at room temperature. It is proposed that the impact toughness of pearlitic steel can be affected by pearlite morphology, at constant interlamellar spacing, only at temperatures above the ductile–brittle transition temperature of the ferrite, when local plastic deformation in the pearlitic ferrite at high angle boundaries can arrest propagating brittle cracks.

MST/730     

Effect of reheat temperature on continuous cooling bainite transformation behavior in low carbon microalloyed steel

The effect of reheat temperature on continuous cooling bainite transformation in a low carbon microalloyed steel was investigated using a dilatometer based on welding thermal simulation process. The variation of microstructure was analyzed in detail by means of optical microscope and transmission electron microscope (TEM). The results showed that the morphology of the main microstructure changes from polygonal ferrite to granular bainite with increasing reheat temperature at a given lower cooling rate. For the higher cooling rate, the microstructure is predominantly lath bainite irrespective of the reheat temperature. The specimens with the relatively fine austenite grain size have the lowest bainite start and finish temperatures among the simulated sub-zones of heat affected zone, which is consistent with the result of the bainite lath width size observed using the TEM. Meanwhile, although the prevailing type of impingement mode of transformation is anisotropic growth impingement for all heat treatment processes, the reheat temperature has some influence on the maximum transformation rate and effective activation energy of bainite transformation.     

Effect of cooling rate on grain size of ferrite in a carbon steel

Abstract

Ferrite grain refinement by accelerated cooling has been studied in a carbon steel. The size of ferrite grains d_α formed by continuous cooling transformation from polygonal austenite has been measured as a function of cooling rate and austenite grain size d_γ. In the cooling rate range studied (q= 0·05–5 K s^?1), d_α was found to be proportional to q^?0·26d_γ^0·46. The mechanism of grain refinement by accelerated cooling is discussed, and it is shown that this occurs in the transformation where the ratio of nucleation to growth rate increases with a decrease in temperature. The austenite grain size dependence of ferrite grain size is shown to become progressively large as the nucleation mode changes from homogeneous to grain surface to edge to corner. A theoretical estimation of ferrite grain size formed by continuous cooling transformation was attempted on the basis of nucleation and growth rates. In the alloy studied, ferrite grain size was theoretically estimated to be proportional to q^?0·17d_γ^0·33. This was in close agreement with the dependence obtained in the present experiment.

MST/466     

变形制度对低碳锰钢组织性能的影响

为了获得细晶铁素体/贝氏体的复相组织,通过控轧控冷工艺研究了低碳锰钢在奥氏体区变形时变形量、终轧温度和卷取温度对组织演变和力学性能的影响规律.研究表明,增加变形量(对应道次间隔时间缩短)可以细化铁素体晶粒,但当终轧温度降低到800℃时,变形量的增加以及开冷温度的降低不利于贝氏体组织的获得.通过调整变形量、终轧温度、可开冷温度并适当降低卷取温度,可使实验钢获得晶粒尺寸约为5μm的铁素体和10%~20%的贝氏体组织,低碳锰钢强塑性能良好.     

Influence of microalloying additions on thickness of grain boundary carbides in ferrite–pearlite steels

Abstract

For a series of plain C and microalloyed steels at two levels of Mn, the growth of grain boundary carbides has been monitored after heating to 920°C and cooling at 40 and 150 K min^?1 through the austenite–ferrite/pearlite transformation down to room temperature. In pearlite free steels, on cooling to room temperature, all the C in solution in the ferrite is able to precipitate as carbides at the boundaries and the grain boundary carbide thickness is dependent on the number of nucleation sites for precipitation. Increasing the cooling rate increases the number of sites and reduces the carbide thickness. In ferrite–pearlite steels, the grain boundary carbides form the ‘tails’ to the pearlite colonies. The thickness of the grain boundary carbide is related to the pearlite reaction, since the temperature at which this occurs controls both the thickness of the carbide nuclei and the amount of C available for precipitating out on these tails. Increasing the cooling rate and Mn content causes a decrease in the transformation temperature and leads to finer carbides. The pearlite nose transformation temperature must be ≦600°C to produce fine (≦0·2 μm) carbides. The austenite grain size, which controls the pearlite colony size, is also very important in determining the thickness of carbides, since the finer the grain size, the greater the carbide density and,for a given amount of C available for precipitation, the finer the resulting carbides. Faster cooling or a higher Mn content refine the pearlite colony size leading to finer carbides. Compared with C–Mn–Al steels, Nb and Ti microalloying additions result in coarser carbides and higher carbide densities. The increased carbide density is due to the finer austenite grain size and the coarser carbides are due to the finer grain size raising the transformation temperature. The implications of these observations on impact behaviour are discussed.

MST/1858     

Structure–property relationships for quenched and tempered flanges made to ASTM A350 LF2 specification

Abstract

The structure–property relationships for quenched and tempered flanges made to the ASTM A350 LF2 specification have been determined. Samples from Al containing and Al free forged flanges have been heated to temperatures in the range 900–1000°C to produce a wide range in γ grain size and quenched in oil or iced water to produce a variety of commercially obtainable microstructures from fine grained ferrite–pearlite to fully bainitic. After quenching, the samples were tempered at 600°C, and the Charpy V-notch impact values at ?46°C and room temperature hardness values were obtained. Raising the quenching temperature reduced the impact energy values and increased the hardness. Increasing the cooling rate also increased hardness, but there was little change in impact behaviour. Impact behaviour was found to be mainly dependent on the γ grain size: the coarser the grain size, i.e. the higher the quench temperature, the lower the impact value. The facet size was also found to be related to γ grain size, indicating that the high angle grain boundaries, i.e. γ, bainite colony, and ferrite boundaries, were the main obstacles to crack propagation. Increasing the cooling rate from the austenitising temperature increased hardness without significantly affecting the impact behaviour. It is believed that the expected deterioration in impact behaviour associated with an increase in hardness was offset by a refinement of the carbides and the removal of the long carbides situated at the interlath ferrite boundaries. The impact energy in joules at ?46°C was given by the equation: impact energy absorbed at ?46°C=82+18·6d^?1/2?0·8H+0·05CR, where d is austenite grain size in millimetres, H is hardness HV10, and CR is cooling rate in K min^?. To meet the ASTM A350 LF2 impact requirement, the γ grain size should be below 40 μm, and this necessitates a grain refining addition.

MST/771     

Investigation on decomposition behavior of austenite under continuous cooling in vanadium microalloyed steel (30MSV6)

In the present study, investigations are focused on microstructural evolution and the resulting hardness during continuous cooling transformation (CCT) in a commercial vanadium microalloyed steel (30MSV6). Furthermore, the effects of cooling rate and austenite grain size (AGS) on CCT behavior of the steel have been studied by employing high-resolution dilatometry. Quantitative metallography accompanied with scanning electron microscopy (SEM) has efficiently confirmed the dilatometric measurements of transformation kinetics and austenite decomposition products. A semi-empirical model has been proposed for prediction of microstructural development during austenite decomposition of the steel and the resultant hardness. The model consists of 8 sub-models including ferrite transformation start temperature, ferrite growth, pearlite start temperature, pearlite growth, bainite start temperature, bainite growth, martensite start temperature and hardness. The transformed fractions of ferrite, pearlite and bainite have been described using semi-empirical Johnson–Mehl–Avrami–Kolmogorov (JMAK) approach in combination with Scheil's equation of additivity. The JMAK rate parameter for bainite has been formulated using a diffusion-controlled model. Predictions of the proposed model were found to be in close agreement with the experimental measurements.     

Acicular ferrite transformation in alloy-steel weld metals

In this paper, the morphology of acicular ferrite in alloy-steel weld metals has been investigated. The effect of the grain size of prior austenite on acicular ferrite transformation has also been studied. It is found that acicular ferrite can form in reheated weld metals when the austenite grain size is relatively large. On the other hand, classical sheaf-like bainite will form at the same temperature if the austenite grain size is kept small. Further results strongly suggest that acicular ferrite is in fact intragranular bainite rather than intragranular Widmanstätten ferrite.     

Microstructure in adiabatic shear bands in a pearlitic ultrahigh carbon steel

Abstract

Adiabatic shear bands, obtained in compression deformation at a strain rate of 4000 s^?1, in a pearlitic 1·3%C steel, were investigated. Shear bands initiated at 55% compression deformation with the width of the band equal to 14 μm. Nano-indentor hardness of the shear band was 11·5 GPa in contrast to the initial matrix hardness of 3·5 GPa. The high strength of the shear band is attributed to its creation from two sequential events. First, large strain deformation, at a high strain rate, accompanied by adiabatic heating, led to phase transformation to austenite. Second, retransformation upon rapid cooling occurred by a divorced eutectoid transformation (DET). The result is a predicted microstructure consisting of nano size carbide particles within a matrix of fine ferrite grains. It is proposed that the DET occurs in iron–carbon steels during high rate deformation in ball milling, ball drop tests and in commercial wire drawing.     

The isochronal δ → γ transformation of high Cr ferritic heat-resistant steel during cooling

Thermal simulation technology was employed to investigate phase transformation in heat-affected zones (HAZ) of high Cr ferritic heat-resistant steel. The simulated continuous cooling transformation diagram was established based on the experimental results obtained from different cooling rates in the range of 0.02–60 °C/s. A theoretical model considering the site saturation nucleation at grain boundaries has been applied to calculate the austenite fraction as a function of cooling rate. It is found that both the austenite fraction and grain size decrease with the increase of cooling rates. The calculated results are mostly consistent with the experimental data.     

Cyclic strain hardening of polygonal and acicular ferrite/bainite microstructures in microalloyed steels in the temperature range − 150°C to 27°C

Cyclic strain hardening has been observed to be markedly sensitive to microstructural changes in microalloyed steels. Two significantly different microstructures - polygonal ferrite grains of average grain size 10–120 μm and acicular ferrite/upper bainite colonies of dimensions 200–625 μm - were examined in order to determine the influence of each on cyclic strain hardening and related properties. Tests were conducted at temperatures between ?150 and 27°C. The cyclic strain hardening exponent, β_c, was significantly more sensitive to changes in the size of the polygonal ferrite grains than to changes in the acicular ferrite/upper bainite colony size.     

Ultrahigh strength hot rolled microalloyed steel: microstructure and properties

Abstract

A low carbon steel alloyed with Ni, Mn, Mo, Cu and microalloyed with Nb and Ti was prepared. Continuous cooling transformation behaviour of the steel was evaluated. Formation of polygonal or Widmanstätten ferrite is suppressed at high temperature and the 'C' curve is shifted to an extreme right. At lower temperatures a flat top 'C' curve with a mixed structure of bainite and martensite was obtained and the transformation temperatures do not vary much with a wide range of cooling rates. The steel was thermomechanically processed at different finishing temperatures and ultrahigh strength values were obtained as a result of austenite grain refinement, highly dislocated fine lath martensite structure along with tiny precipitates of microalloying carbide and carbonitride at all finish rolling temperatures. The stable and large TiN/TiCN particles formed during casting have impaired the impact toughness values at ambient and at ?40°C temperatures.     

Effect of austenite microstructure and cooling rate on transformation characteristics in a low carbon Nb-V microalloyed steel

Deformation dilatometry has been used to simulate controlled hot rolling followed by cooling of a Nb-V low carbon steel, looking for conditions corresponding to wide austenite grain size distributions prior to transformation. Recrystallization and non-recrystallization deformation schedules were applied, followed by controlled cooling at rates from 0.1 °C/s to about 200 °C/s, and the corresponding continuous cooling transformation (CCT) diagrams were constructed. The resultant microstructures ranged from polygonal ferrite (PF) and pearlite (P) at slow cooling rates to bainitic ferrite (BF) accompanied by martensite (M) for fast cooling rates. Plastic deformation of the parent austenite accelerated both ferrite and bainite transformations, displacing the CCT curve to higher temperatures and shorter times. However, it was found that the accelerating effect of strain on bainite transformation weakened as the cooling rate diminished and the polygonal ferrite formation was enhanced. Moreover, it was found that plastic deformation had different effects on the refinement of the microstructure, depending on the cooling rate. An analysis of the microstructural heterogeneities that can impair toughness behavior has been done.     

含磷和钒热轧TRIP钢组织控制及力学性能研究

为探讨含磷和钒热轧TRIP钢的组织控制和力学性能,采用不同变形温度（900和800℃）,研究其相变行为,并在此基础上进行热轧试验.研究表明：随着冷速增加,变形温度对铁素体相变开始温度（Ar3）的影响逐渐增大;相同冷速条件下,变形使贝氏体相变开始温度（Bs）升高;变形对贝氏体相变的促进作用,随着变形温度的降低而减弱.终轧...     

Effect of strain on formation of ultrafine ferrite in surface of hot rolled microalloyed steel

Abstract

The phenomenon of ultra grain refinement of ferrite in surface layers of hot rolled strip has been studied in a low carbon, niobium microalloyed steel. Wedge specimens were used, to vary the nominal equivalent strain applied during rolling from zero to approximately unity, and the cooling rate after rolling was varied from ~ 20 to 1 K s ^-1. In contrast with previous work, which contended that a very coarse austenite grain size and a low rolling temperature near the Ar ₃ were essential to obtain ultrafine ferrite in surface layers, such ultrafine layers were observed after rolling coarse austenite at up to 150 K above the Ar ₃ and after rolling fine grained austenite near the Ar ₃. In the case of coarse grained austenite, a critical nominal rolling strain needed to be exceeded to trigger the surface layer phenomenon, upon which cooling rate had little effect on the surface layer's grain size. Refining the prior austenite grain size had the further beneficial effect of refining the grain size at the centre of the rolled product, for example to 2·6 μm, while the surface layer was refined to 0·7 μm.     

Effect of dissolution and precipitation of Nb on the formation of acicular ferrite/bainite ferrite in low-carbon HSLA steels

Effect of dissolution and precipitation of Nb on the phase transformation during cooling was investigated. It is firstly recognized that either the formation of acicular ferrite or the separation of bainite ferrite could be adjusted by the preparation of the steel specimens with different amounts of solute Nb and Nb-precipitates in austenite (isothermally holding at 850 °C for different durations). An increase in isothermal duration at 850 °C would spawn more Nb(CN) precipitates, leading to a microstructural evolution from bainite ferrite to acicular ferrite/bainite ferrite dual phase, and eventually to acicular ferrite in the final microstructure. This could be explained by the solution of Nb in the austenite, due to the solute dragging effect of Nb, can decrease the A_r3 temperature and promote the formation of bainite ferrite, while the precipitation of NbC can increase the A_r3 temperature and promote the formation of acicular ferrite by increasing the nucleation sites of acicular ferrite. Thus, the properties of acicular ferrite/bainite ferrite dual phase steel can generally be improved by appropriately controlling the state of Nb (Nb(CN) as precipitates and Nb in solution) in the austenite before cooling, which provides a new approach to the modification of acicular ferrite/bainite ferrite ratio.