共查询到20条相似文献,搜索用时 15 毫秒
1.
Clarence W.DE SILVA 《Instrumentation》2019,(4):72-84
An engineering system may consist of several different types of components,belonging to such physical"domains"as mechanical,electrical,fluid,and thermal.It is t... 相似文献
2.
INTEGRAL EQUATION METHOD'S APPLICATION IN HOLE-EDGE STRESS OF COMPOSITE MATERIAL PLATE WITH DIFFERENT SHAPED HOLES 总被引:1,自引:0,他引:1
LI Cheng ZHENG Yanping 《机械工程学报(英文版)》2008,21(6):115-118
The strength of composite plate with different hole-shapes is always one of the most important but complicated issues in the application of the composite material. The holes will lead to mutations and discontinuity to the structure. So the hole-edge stress concentration is always a serious phenomenon. And the phenomenon makes the structure strength decrease very quickly to form dangerous weak points. Most partial damage begins from these weak points. According to the complex variable functions theory, the accurate boundary condition of composite plate with different hole-shapes is founded by conformal mapping method to settle the boundary condition problem of complex hole-shapes. Composite plate with commonly hole-shapes in engineering is studied by several complex variable stress fimction. The boundary integral equations are founded based on exact boundary conditions. Then the exact hole-edge stress analytic solution of composite plate with rectangle holes and wing manholes is resolved. Both of offset axis loadings and its influences on the stress concentration coefficient of the hole-edge are discussed. And comparisons of different loads along various offset axis on the hole-edge stress distribution of orthotropic plate with rectangle hole or wing manhole are made. It can be concluded that hole-edge with continuous variable curvatures might help to decrease the stress concentration coefficient; and smaller angle of outer load and fiber can decrease the stress peak value. 相似文献
3.
30 keV Ga+ focused ion beam induced secondary electron (iSE) imaging was used to determine the relative contrast between several materials. The iSE signal compared from C, Si, Al, Ti, Cr, Ni, Cu, Mo, Ag, and W metal layers does not decrease with an increase in target atomic number Z2, and shows a non-monotonic relationship between contrast and Z2. The non-monotonic relationship is attributed to periodic fluctuations of the stopping power and sputter yield inherent to the ion–solid interactions. In addition, material contrast from electron-induced secondary electron (eSE) and backscattered electron (BSE) images using scanning electron microscopy (SEM) also shows non-monotonic contrast as a function of Z2, following the periodic behavior of the stopping power for electron–solid interactions. A comparison of the iSE and eSE results shows similar relative contrast between the metal layers, and not complementary contrast as conventionally understood. These similarities in the contrast behavior can be attributed to similarities in the periodic and non-monotonic function defined by incident particle–solid interaction theory. 相似文献
4.
The fraction defective of semi-finished products is predicted to optimize the process of relay production lines, by which production quality and productivity ar... 相似文献
5.
The use of hand gestures can be the most intuitive human-machine interaction medium.The early approaches for hand gesture recognition used device-based methods.... 相似文献
6.
This paper proposes a novel grading method of apples,in an automated grading device that uses convolutional neural networks to extract the size,color,texture,an... 相似文献
7.
分布动态载荷识别的抗噪处理 总被引:2,自引:2,他引:0
针对正交多项式频域法在用多种响应对矩形薄板进行载荷识别中抗噪性较差的问题,综合运用平均法、矩阵预处理和奇异值截断法等方法对之进行改善,并引入空间映射的思想,将该方法的应用范围拓展为复杂的模型.利用仿真算例,证实了该方法具有较好的抗噪性. 相似文献
8.
针对工程实践中环网通讯相关问题的处理缺乏理论基础及国产化安全级DCS平台的开发缺乏成熟经验借鉴问题,对基于MELTAC-N平台核电厂安全级DCS环网的软硬件实现进行了研究。提出了安全级DCS环网双环网冗余设计、光切换开关设计等硬件设计方法,以及以RPR协议为基础,采用全数据收发策略的软件设计方法。在CPR1000安全级DCS平台上对安全级DCS环网的可靠性及实时性进行了评价,并进行了容错能力、响应时间及响应时间稳定性测试验证实验。结果表明,基于MELTAC-N平台安全级DCS环网软硬件设计具有较好的容错能力及响应时间稳定性。 相似文献
9.
J. A. Williams 《Lubrication Science》1997,3(3):267-306
Abrasive wear has long been recognised as one of the most potentially serious tribological problems facing the operators of many types of plant and machinery; several industrial surveys have indicated that wear by abrasion can be responsible for more than 50% of unscheduled machine and plant stoppages. Locating the operating point of a tribological contact in an appropriate operational ‚map’︁ can provide a useful guide to the likely nature and origins of the surface degradation experienced in use, though care must be exercised in choosing the most suitable parameters for the axes of the plot. Laboratory testing of materials and simulations of machine contacts are carried out for a number of purposes; at one level for the very practical aims of ranking candidate materials or surface hardening treatments in order of their wear resistance, or in an attempt to predict wear lives under field conditions. More fundamentally, tests may be aimed at elucidating the essential physical mechanisms of surface damage and loss, with the longer term aim of building an analytical and predictive model of the wear process itself. In many cases, component surface damage is brought about by the ingress of hard, particulate matter into machine bearing or sealing clearances. These may be running dry although, more usually, a lubricant or service fluid is present at the interface. A number of standardised wear test geometries and procedures have been established for both two- and three-body wear situations, and these are briefly described. Although abrasive wear is often modelled as following an ‚Archard’︁ equation (i.e. a linear increase in material loss with both load and time, and an inverse dependence on specimen hardness) both industrial experience and laboratory tests of particularly lubricated contacts show that this is not always the case: increasing the hardness differential in an abrasively contaminated lubricated pair may not always reduce the rate of damage to the harder surface. 相似文献
10.
CHEN Sunyi 《机械工程学报(英文版)》2007,20(6):13-17
A graph as the new engineering method for estimate the safety of bulging deformation of coke tower is proposed. Through stresses analysis of circumferential weld of coke tower and comparing the stresses produced by pressure with heat stress of steady state, residual stress, bending stress produced by both itself weight and wind loads, it showed that the stresses produced by pressure on the angle distortion are the main factor of equivalent stress of the combined stress. After comparing four kinds of stress controlling conditions, the relation to stress with depth of angular distortion, grade of curvature of angular distortion and half of region of angular distortion has been inferred. Graph of deformation allowable value of coke tower for different condition by angular distortion and half of region of angular distortion has been plotted. The five steps for its engineering use have been explained. The lighter the grade of curvature is, the larger of bulge allowance, may be, and the bigger of depth of angular distortion may pose too. For the coke tower with a popular structure of Dg 5 400 mm×28 mm, the result by graph is nearly more than the result of two formulas formed by other research, the error is less than 7.0%. But, the graph can be easily applied to different size of angular distortion. 相似文献
11.
《Measurement》2016
This article describes designing, implementation and tuning processes of multiple-tapped-delay-line (MTDL). Obtained MTDL can be implemented in various field-programmable-logic-devices (FPGA) devices and applied for time-to-digital-converters (TDC) construction. The task of tuning process is the tapped-delay-line (TDL) linearisation, and consists of two stages. The first stage depends on selecting an appropriate configurable-logic-block (CLB) for particular delay-segment realization and selecting proper connection between these blocks. The second tuning stage, that is essential from this article viewpoint, depends on inter CLBs connecting wires delay regulation realized directly by load regulation. The Load regulation depends on connecting an appropriate number of unused three-state-buffers or CLB inputs to the wire which delay is adjusted. Depending on the number of inputs connected to the wire its capacitance changes that influences its time-constant and finally changes its time-delay.The MTDL mathematical model, obtained characteristics and results of time-interval (TI) measurements are also presented. The derived TDL model provides information about how the particular wire delay should be changed and in which order the changes should be executed. This makes the designing process predictable and easy to carry out. Presented characteristics confirm the proper operation of presented linearisation technique. The proper operation of the whole measuring module is confirmed by obtained TIs histograms presentation. 相似文献
12.
M. Stedman 《Journal of microscopy》1988,152(3):611-618
Parameters describing the topographic character of a surface (height, surface wavelength, slope and curvature) can be derived from equivalent sinusoidal profiles. The response of a surface-measuring instrument may be modelled in terms of instrument parameters such as stylus radius, and scanning range and resolution. The performance of the instrument may then be mapped as a zone in amplitude-wavelength (AW) space to show the sinusoidal profiles it is capable of measuring. In a first-order analysis the STM and AFM are considered as equivalent to contact-stylus instruments with a notional stylus radius equal to the tip radius plus the gap. Comparisons between different instruments and types of instrument are readily made by mapping in AW space. The error arising from convolution of the sinusoidal profile with that of the finite tip may be quantified and plotted as contours in AW space. 相似文献
13.
Fractional order nonsingular terminal sliding mode control for flexible spacecraft attitude tracking
This paper investigates a fractional terminal sliding mode control for flexible spacecraft attitude tracking in the presence of inertia uncertainties and extern... 相似文献
14.
15.
以德士古气化炉耐火砖的内壁蚀损检测设备为基础,对采集到的点云数据做了进一步处理.通过对数据的筛选和剔除,实现了数据点的平滑降噪细化和精简.然后利用点云对整、网格划分和分色显示等方法,最终完成了内壁腐蚀情况的三维建模.重点讨论了点云数据的预处理及后处理的方法,并根据内壁耐火砖的腐蚀阈值,提出了一种气化炉内壁腐蚀区域的识别与分割方法.对耐火砖的腐蚀分析、气化炉的生产与维修提供了可靠依据,并在工程应用中获得了一致认可. 相似文献
16.
17.
EXPERIMENTAL RESEARCH AND DESIGN ON HEAT TRANSFER OF EVAPORATOR USED IN THE LARGE QUICK FREEZE PLANT
ZHENG Chuanxiang ZHUO Chuanmin 《机械工程学报(英文版)》2007,20(6):18-23
The evaporator is the main part of a quick-freeze equipment. There are many factors influencing the heat transfer coefficient of an evaporator. The most important factors among them are the fin shape, tube diameter, distance of fin space, frost, and velocity of air flow etc. They mainly influence the thermal efficiency of an evaporator, and therefore its thermal efficiency has direct relationship with the whole efficiency of the quick freeze plant. Evaporators with different structural types have different heat transfer efficiency. In order to obtain high efficiency structure of evaporator, 8 evaporator models with different fin shape, tube diameter and tube arrangement are analyzed and compared. The calculation results show that the integral waved fins, equilateral-triangle arranged small diameter tubes and varying fin-spacing has the highest heat transfer coefficient. The experimental result also shows that the evaporator with this type of structure has better thermal efficiency. The experimental result is in good agreement with the calculation result. It can instruct engineering design for usual designer. A real quick-freeze equipment is designed and put into production. The result shows that, compared with traditional domestic quick-freeze equipments, this equipment decreases by 40% in size and by 20% in energy consumption. 相似文献
18.
LI Xianghua ZHANG Jianwu School of Mechanical Engineering Shanghai Jiaotong University Shanghai China 《机械工程学报(英文版)》2007,20(2):1-5
A newly found phenomenon of carved driving wheels of a rear-wheel-drive tractor used in an airport is discussed. The circum of every driving wheel is damaged at three regions,which distribute regularly and uniformly. Everyday,the tractor tows a trailer which are times heavier than the tractor,and moves on the same road in the airport. The phenomenon is explained by the torsional self-excited vibration system of the powertrain. The simplified torsional vibration system is discribed by a 2-order ordinary differential equation,which has a limit circle. Experiments and numerical simulations show the followings: Because of the heavy trailer,the slip ratio of the tractor’s driving wheels is very large. Therefore,there is severe torsional self-excited vibration in the tractor’s drivetrain,and the self-excited vibration results in severe and regular fluctuations of the rear wheel’s velocity. The severe fluctuations in velocity fastens the damage of the driving wheels. At the same time,the time interval in which an arbitrary point in the circum of the driving wheel contacts with the road twice is two times more than the period of the torsional self-excited vibration,and this times explained the existence of three damaged regions. At last,it points out that the phenomenon can be avoided when the torsional damping is large enough. 相似文献
19.
WU Shixiong WANG Chengyong FAN Jingming 《机械工程学报(英文版)》2007,20(5):1-4
An approach is presented to generate rough interference-free tool-paths directly from massive unorganized data in rough machining that is performed by machining volumes of material in a slice-by-slice manner. Unorganized point-cloud is firstly converted to cross-section data. Then a robust data-structure named tool-path net is constructed to save tool-path data. Optimal algorithms for partitioning sub-cut-areas and computing interference-free cutter-locations are put forward. Finally the tool-paths are linked in a zigzag milling mode, which can be transformed into a traveling sales man problem. The experiment indicates optimal tool paths can be acquired, and high computation efficiency can be obtained and interference can be avoided successfully. 相似文献
20.
《机械设计与研究》2014,(3)
正3-11 September,2014University of Bologna,Bologna,Italy www.summerscrews.org summerscrews2014.ing.unibo.it SUMMER 20SCREWS 14In 2014,our screw-theory school comes to the world's oldest university.In early September,Summer Screws'14 will gather six experts in the application of screw theory in robotics and up to 40 participants at the University of Bologna,Bologna,Italy.The school will teach attendees how to apply existing methods and empower them to develop new ones in their own research.The basic theoretical notions will be introduced in a rigorous manner,emphasizing examples,applications,and exercises.Scholarships are available. 相似文献