Formation of ZnAl2O4 in the Presence of Cl2

The formation of ZnAl₂O₄ spinel in diffusion couples of Al₂O₃ and ZnO was investigated between 1000° and 1390°C in air and in air containing 4.8 vol% Cl₂ by X-ray diffraction, electron probe microanalysis, and scanning electron microscopy. The rate of formation of a spinel layer obeyed a parabolic rate law and was accelerated remarkably by the presence of Cl₂. The interdiffusion coefficient, , and the activation energy, E, were calculated to be 10⁻⁸ to 10⁻⁹ cm²/s and 123 kcal/mol (514 kJ/mol) in air and 10⁻⁷ cm²/s and 31 kcal/mol (130 kJ/mol) in air containing 4.8 vol% Cl₂, respectively.     

Growth of Single-Crystal and Polycrystalline Thin Films of MgAl2O4 and MgFe2O4

Single-crystal and polycrystalline films of Mg-Al₂O₄ and MgFe₂O₄ were formed by two methods on cleavage surfaces of MgO single crystals. In one procedure, aluminum was deposited on MgO by vacuum evaporation. Subsequent heating in air at about 510°C formed a polycrystalline γ-Al₂O₈ film. Above 540°C, the γ-Al₂O, and MgO reacted to form a single-crystal MgAl₂O₄ film with {001} MgAl₂O₄‖{001} MgO. Above 590°C, an additional layer of MgAl₂O₄, which is polycrystalline, formed between the γ-Al₂O₃ and the single-crystal spinel. Polycrystalline Mg-Al₂O₄ formed only when diffusion of Mg²⁺ ions proceeded into the polycrystalline γ-Al₂O₃ region. Corresponding results were obtained for Mg-Fe₂O₄. MgAl₂O₄ films were also formed on cleaved MgO single-crystal substrates by direct evaporation, using an Al₂O₃ crucible as a source. Very slow deposition rates were used with source temperatures of ∼1350°C and substrate temperatures of ∼800°C. Departures from single-crystal character in the films may arise through temperature gradients in the substrate.     

Indirect Dissolution of (Al, Cr)2O3 in CaO—MgO—Al2O3—SiO2 (CMAS) Melts

The dissolution of (Al, Cr)₂O₃ into CaO—MgO—Al₂O₃—SiO₂ melts, under static and forced-convective conditions was investigated at 1550°C in air. With sufficient MgO in the melt, or sufficient Cr₂O₃ in (Al, Cr)₂O₃, a layer consisting of a spinel solid solution, Mg(Al, Cr)₂O₄, formed at the (Al, Cr)₂O₃/melt interface. The dissolution kinetics of 1.5 and 10 wt% Cr₂O₃ specimens were determined as a function of immersion time, specimen rotation rate, and magnesia content of the melt. Electron microprobe analysis was used to characterize concentration gradients in the (Al, Cr)₂O₃ sample, the Mg(Al, Cr)₂O₄ spinel, or in the melt after immersion of specimens containing 1.5 to 78 mol% Cr₂O₃. The dissolution kinetics and microprobe analyses indicated that a steady-state condition was reached during forced-convective, indirect (Al, Cr)₂O₃ dissolution such that spinel layer formation was rate limited by solid-state diffusion through the spinel layer and/or through the specimen, and spinel layer dissolution was rate limited by liquid-phase diffusion through a boundary layer in the melt. This is consistent with a model previously developed for the indirect dissolution of sapphire in CMAS melts.     

Grain Growth of ZnO in ZnO-Bl2O3 Ceramics with Ai2O3 Additions

Grain growth of ZnO during liquid-phase sintering of a ZnO-6 wt% Bi₂O₃ ceramic was investigated for A1₂O₃ additions from 0.10 to 0.80 wt%. Sintering in air for 0.5 to 4 h at 900° to 1400°C was studied. The AI₂O₃ reacted with the ZnO to form ZnAl₂O₄ spinel, which reduced the rate of ZnO grain growth. The ZnO grain-growth exponent was determined to be 4 and the activation energy for ZnO grain growth was estimated to be 400 kJ/mol. These values were compared with the activation parameters for ZnO grain growth in other ceramic systems. It was confirmed that the reduced ZnO grain growth was a result of ZnAl₂O₄ spinel particles pinning the ZnO grain boundaries and reducing their mobility, which explained the grain-growth exponent of 4. It was concluded that the 400 kJ/mol activation energy was related to the transport of the ZnAl₂O₄ spinel particles, most probably controlled by the diffusion of O^2- in the ZnAl₂O₄ spinel structure.     

Mineralizing Effect of Li2B4O7 and Na2B4O7 on Magnesium Aluminate Spinel Formation

Lithium borate (Li₂B₄O₇) and sodium borate (Na₂B₄O₇) mineralize spinel formation from stoichiometric MgO and Al₂O₃ between 1000° and 1100°C. Mineralization with both compounds is shown to be mediated by B-containing liquids which form glass on cooling. However, the liquid compositions depend on the type of mineralizer and temperature, suggesting that templated grain growth or dissolution–precipitation mechanisms are operating, one dominating over the other under certain conditions. Na₂B₄O₇-mineralized compositions show predominantly templated grain growth at 1000°C, which changes to dissolution–precipitation at 1100°C, whereas Li₂B₄O₇-mineralized compositions show dissolution–precipitation from 1000°C. Li₂B₄O₇ is a stronger mineralizer as spinel formation is complete with 3 wt% Li₂B₄O₇ at 1000°C and with ≥1.5 wt% addition at 1100°C, whereas Na₂B₄O₇-mineralized compositions are found to retain some unreacted corundum even at 1100°C.     

Interdiffusion and Association Phenomena in the System NiO-Al2O3

The rate of formation of NiAl₂O₄ by reaction between single crystals of NiO and Al₂O₃ can be described by k = 1.1 × 10⁴ exp (−108,000 ± 5,000/ RT ) cm²/s. In NiO the behavior of D as a function of concentration supports the Lidiard theory of diffusion by impurity-vacancy pairs. A good fit of the theory to the experimental results was obtained by assuming that Al³⁺ ions diffuse as [Al_Ni· V_Ni]'pairs. The diffusion coefficient of pairs, D_p , obeys the equation 6.6 × 10⁻² exp (−54,000 ± 3,000/ RT ) cm²/s. The free energy of association for pairs was calculated to range from 6.5 kcal/mol at 1789°C to 9.0 kcal/mol at 1540°C. The interdiffusion coefficients in the spinel showed a constant small increase with increasing concentration of Al³⁺ dissolved in the spinel.     

Exsolution of β-Ga2O3 Crystalline Solutions in the System MgAl2O3-Ga2O3

The subsolidus phase equilibrium diagram for the pseudobinary join MgAl₂O₄-Ga₂O₃ was determined. The shape of the exsolution boundary was obtained by heat-treating samples pre- equilibrated at 1600°C. Crystalline solubility of Ga₂O₃ in MgAl₂O₄ decreased from 73 mole % at 1600°C to 55 mole % at 1200°C. The crystalline solution was formed by the replacement of Mg²⁺ions by Ga³⁺ ions to produce a cation defect spinel. The phase precipitated was the mono-clinic δ-Ga₂O₃ (=δ-Al₂O₃ structure). Changes in the ratios of relative X-ray diffraction intensities indicated that the crystalline solutions also disorder with temperature.     

Initial Sintering of α-Cr2O3

Since the difference between oxygen-ion and cation diffusion coefficients is greater for α-Cr₂O₃ than for α-Fe₂O₃ or α-Al₂O₃, a study of initial-sintering kinetics was undertaken to show unequivocally which species is rate controlling. Fine powders of α-Cr₂O₃, obtained by thermal decomposition of reagent-grade (NH₄)₂Cr₂O₇, were lightly compacted and their isothermal rates of shrinkage were determined between 1050° and 1300°C. Resultant data follow volume-diffusion sintering models, and calculated diffusion coefficients agree with, those measured for oxygen ions in α-Cr₂O₃. There is little evidence that oxygen diffusion along grain boundaries becomes so enhanced that chromium ions are left in control of the process.     

Molten Salt Synthesis of Magnesium Aluminate (MgAl2O4) Spinel on Ti3AlC2 Substrate

A MgAl₂O₄ (MA) spinel layer was synthesized on Ti₃AlC₂ substrate through the molten salt synthesis (MSS) method. The Ti₃AlC₂ substrate was immersed in MgCl₂·6H₂O powders and treated at 800°, 850°, and 900°C for 4 h in air. A continuous and 10-μm-thick MgAl₂O₄ layer was obtained at 900°C, by which the surface hardness of Ti₃AlC₂ can be effectively improved. The combined scanning electron microscopy observations and crystal morphology simulation further revealed that the as-formed MgAl₂O₄ presents tetragonal bipyramids morphology with (400)-orientation.     

Phase Equilibria in the Spinel Region of the System FeO-Fe2O3-Al2O3

Phase relations in the spinel region of the system FeO-Fe₂O₃-Al₂O₃ were determined in CO₂ at 1300°, 1400°, and 15000°C and for partial oxygen pressures of 4 × 10⁻⁷ and 7 × 10⁻¹⁰ atmospheres at 15OO°C. The spinel field extends continuously from Fe₃O_4-x to FeAl₂O_4+z.     

Crystal Chemistry and Phase Relations in the System Li2O-Fe2O3-TiO2

Above 755°C, compounds along the spinel join LiFe₅O₈-Li₄Ti₅O₁₂ form a complete solid solution and below that temperature a two-phase region separates the ordered LiFe₅O₈ and the disordered spinel phase. At 800° and 900°C, cubic LiFeO₂ ( ss ) and monoclinic Li_zTi0₃ ( ss ) exist on the monoxide join LiFeO₂-Li₂TiO₃. The distributions of cations in both the spinel and monoxide structures were calculated as a function of equilibrium temperature and composition. Sub-solidus equilibria in the system Li₂O-Fe₂O₃-TiO₂ at 800° and 900°C were determined for compositions containing ∼50 mol% Li₂O.     

Activity–Composition Relations in NiAl2O4─MnAl2O4 Solid Solutions and Stabilities of NiAl2O4 and MnAl2O4 at 1300° and 1400°C

Activities of NiO were measured in the oxide and spinel solutions of the system MnO–NiO–Al₂O₃ at 1300° and 1400° C with the aim of deriving information on the thermodynamic properties of the spinel phases. Synthetic samples in selected phase assemblages of the system were equilibrated with metallic nickel and a gas phase of known oxygen partial pressures at a total pressure of 1 atm. The data on NiO activities and directions of conjugation lines between coexisting oxide and spinel phases were used to establish the activity–composition relations in spinel solid solutions at 1300° and 1400°C. The MnAl₂O₄–NiAl₂O₄ solid solutions exhibit considerable negative deviations from ideality at these temperatures. The free energy of formation of MnAl₂O₄ from its oxide components (MnO + Al₂O₃) at 1300° and 1400°C is calculated to be −24.97 and −26.56 kJ. mol⁻¹, respectively. The activities determined in the stoichiometric spinel solid solutions are more negative as compared with those predicted from cation distribution models.     

Solubility and Crystal Growth of ZnAl2,O4 and AI2O3 in Molten PbF2 Solutions

The solubility of ZnAl₂O₄ (gahnite spinel) and NZOI (corundum) in their respective molten PbF₂ solutions was determined by a sealed-tube quenching method between 900° and 1250°C. Differential thermal analysis was used below 900°C. The solubilities (crystal-constituent/ PbF₂ weight ratio) at 1200°C were 0.151 for A1₂O₃ and 0.108 for ZnAl₂O₄, whereas at 900°C they were 0.093 and 0.048, respectively. These results are compared with those of single-crystal growth experiments and the crystalline products are described.     

Coherent Precipitation in the System MgO-Al2O3-Cr2O3

An isothermal section of the ternary system MgO–Al₂O₃-Cr₂O₃ was determined at 1700°± 15°C to delineate the stability field for spinel crystalline solutions (cs). Crystalline solutions were found between the pseudobinary joins MgAl₂O₄–Cr₂O₃ and MgCr₂O₄-Al₂O₃, and the binary join MgAl₂O₄-MgO. The first two crystalline solutions exhibit cation vacancy models while the latter can probably be designated as a cation interstitial model. Precipitation from spinel cs may proceed directly to an equilibrium phase, (Al_1-xCr_x)₂O₃, with the corundum structure or through a metastable phase of the probable composition Mg(Al_1-xC_r)₂₆O₄₀. The composition and temperature limits were defined where the precipitation occurs via metastable monoclinic phases. The coherency of the metastable monoclinic phase with the spinel cs matrix can be understood by considering volume changes with equivalent numbers of oxygens and known crystallographic orientation relations. Electron probe and metallographic microscope investigations showed no preferential grain boundary precipitation.     

Reducing the Sintering Temperature for MgO–Al2O3Mixtures by Addition of Cryolite (Na3AlF6)

The preparation of near stoichiometric spinel and alumina-rich spinel composites from Al₂O₃and MgO powders with the addition of Na₃AlF₆up to 4 wt% in the temperature range 700°–1600°C was studied; 98 wt% spinel containing 72 wt% Al₂O₃can be produced from the mixture of 72 wt% (50 at.%) Al₂O₃+ 28 wt% (50 at.%) MgO powders with the addition of 1 wt% Na₃AlF₆fired at 1300°C for 1 h. Spinels containing 81–85 wt% Al₂O₃can be produced from either the mixture of 90 wt% (78 at.%) Al₂O₃+ 10 wt% (22 at.%) MgO or the mixture of 95 wt% (88 at.%) Al₂O₃+ 5 wt% (12 at.%) MgO powders with the addition of 4 wt% Na₃AlF₆in the temperature range 1300°–1600°C by using a torch-flame firing for 3 min, followed by quenching in water, while the same system under slow cooling in a furnace results in spinel containing 74–76 wt% Al₂O₃. Microscopic studies indicate that the alumina-rich spinel composites consist of a continuous majority spinel phase and an isolated minority corundum phase, regardless of slow cooling in a furnace or quenching in water.     

Thermal Grooving of MgO and Al2O3

High-purity polycrystalline MgO and Al₂O₃ were thermally grooved at 1500° and 1600°C. Accurate techniques were developed for following the growth of a single groove. For high-purity samples growth kinetics were essentially similar to those reported in the literature but were determined to be controlled by volume diffusion. Specimens for thermal grooving were prepared from Al₂O₃ to which transition metal oxides (Fe₂O₃₉, MnO, and TiO₂), which are known to accelerate shrinkage and sintering of Al₂O₃ powder compacts, had been added; the rate of groove growth was increased remarkably by minor amounts of these additives. Control of partial pressure indicated that Fe²⁺ and Ti⁴⁺ are the species active in promoting groove growth. Substantial evidence was found for volume diffusion as the mechanism controlling groove formation.     

Phase Relations and Lattice Constants in the MgO-Al2O3-Ga2O3 System at 1550°C

Phase relations and lattice constants in the MgO–Al₂O₃–Ga₂O₃ system at 1550°C have been determined experimentally. In a large part of this system, only a nonstoichiometric spinel is stable. Compositions as extreme as 12.5 mol% MgO–20.5 mol% Ga₂O₃–67 mol% Al₂O₃ for a homogeneous spinel are possible. In the bordering phase diagrams of MgO–Al₂O₃ and MgO–Ga₂O₃, the composition of the spinel is as high as 63 mol% Al₂O₃ or Ga₂O₃, respectively. The contributions of all simple ionic exchange reactions on the lattice constant of the spinel have been deduced from X-ray diffractometry data.     

TEM Characterization of Nanostructured MgAl2O4 Synthesized by a Direct Conversion Process from γ-Al2O3

Nanostructured MgAl₂O₄ spinel was synthesized by a direct conversion process from cubic γ-Al₂O₃. The effect of post-annealing temperature (300°, 500°, and 800°C) on MgAl₂O₄ phase formation was investigated using transmission electron microscopy, selected area electron diffraction (SAED), electron energy loss spectroscopy (EELS), and energy-dispersive spectroscopy (EDS). Relative diffraction intensities as well as lattice parameter measurements from SAED revealed that MgAl₂O₄ spinel structure starts forming at temperatures as low as 300°C. EELS and EDS spectrum images also revealed an increase in elemental homogeneity with increasing annealing temperature. The degree of ordering of Mg and Al between octahedral and tetrahedral sites has been determined from relative diffraction intensities. Results show that annealing to 800°C leads to a spinel phase with an order parameter of 0.78.     

Phase Equilibrium Studies in the System Iron Oxide-Al2O3-Cr2O3

Subsolidus phase relations in the system iron oride-Al₂O₂-Cr₂O₃ in air and at 1 atm. O₂ pressure have been studied in the. temperature interval 1250° to 1500°C. At temperatures below 1318° C. only sesquioxides with hexagonal corundum structure are present as equilibrium phases. In the temperature interval 1318° to 1410°C. in air and 1318° to 1495° C. at 1 atm. O₂, pressure the monoclinic phase Fe₂O₃. Al₂O₃ with some Cr₂O₃ in solid solution is present in the phase assemblage of certain mixtures. At temperatures above 1380°C. in air and above 1445°C. at 1 atm. O₂ pressure a complex spinel solid solution is one of the phases present in appropriate composition areas of the system. X-ray data relating d- spacing to composition of solid solution phases are given.     

Decomposition of Al2TiO5 and Al2(1-x)MgxTi(1+x)O5 Ceramics

The decomposition of Al_{2(1- x )}Mg _x Ti_{(1+ x )}O₅ ceramics in air has been studied between 900° and 1175°C for 0 lessthan equal to x lessthan equal to 0.6. The decomposition temperature versus composition x predicted using a thermodynamic model based on the regular solution approach is in satisfactory agreement with the experimental results. The decomposition kinetics has been studied at 1100°C for x = 0, 0.1, and 0.2 and follows a nucleation and growth mechanism. Random nucleation of the reaction products is hindered by the high elastic stresses that result from the molar volume change related to decomposition because of the small chemical driving force available. Decomposition occurs only at a limited number of sites, probably associated with the presence of impurities and/or glassy phase. The decomposition products grow as nodules formed by an Al₂O₃ (+ MgAl₂O₄ for x > 0) core and a TiO₂ shell. The growth is parabolic for x = 0 and linear for x = 0.1 and 0.2. The rate-controlling step in the decomposition mechanism of pure Al₂TiO₅ ( x = 0) is the transport of Al³⁺ ions through the TiO₂-rutile phase.