Scanning electron microscopy study of the cross section of intermetallic compound in the solder ball on the plastic ball grid array package following reliability tests

The 63Sn-37Pb solder ball (φ=300 μm) was attached to gold-nickel-plated plastic ball grid array (PBGA) substrates, with gold and nickel thicknesses of 0.6 μm and 7 μm, respectively. The thickness of the intermetallic compound (IMC) in solder balls was measured following each instance of infrared (IR) reflow (90 sec at 230 °C), level II preconditioning, a pressure cooking test (for 96 h or 168 h), and a temperature cycle test (with 500 or 1,000 cycles). Scanning electron microscopy (SEM) was used to identify the cross-section sites of the solder balls following testing. Following all the reliability tests, the IMC demonstrated that an IMC thickness exceeding 5 μm will reduce the solder ball shear strength owing to diffusion of Ni into the solder balls.     

The effect of isothermal aging on the thickness of intermetallic compound layer growth between low melting point solders and Ni-plated Cu substrate

The growth kinetics of the intermetallic compound (IMC) layer formed between two low melting point solders and electrolytic Ni/Cu substrate by solid-state isothermal aging were examined. The solders were 100 In and In-48Sn. A quantitative analysis of the IMC layer thickness as a function of aging time and aging temperature was performed. Experimental results showed that the IMCs, such as In₂₇Ni₁₀ and Ni₃(In, Sn)₄), were observed for different solders. Additionally, the growth rate of these IMCs increased with the aging temperature and time. The layer growth of the IMC in the couples of indium solder alloy/electrolytic Ni system satisfied the parabolic law at a given temperature range. As a whole, because the values of the time exponent (n) are approximately 0.5, the layer growth of the IMC was mainly controlled by the diffusion mechanism over the temperature range studied. The apparent activation energies for IMC growth were 60.03 kJ/mol for In₂₇Ni₁₀ and 72.84 kJ/mol for Ni₃(In, Sn)₄.     

Effect of cooling rate on growth of the intermetallic compound and fracture mode of near-eutectic Sn-Ag-Cu/Cu pad: Before and after aging

Several near-eutectic solders of (1) Sn-3.5Ag, (2) Sn-3.0Ag-0.7Cu, (3) Sn-3.0Ag-1.5Cu, (4) Sn-3.7Ag-0.9Cu, and (5) Sn-6.0Ag-0.5Cu (in wt.% unless specified otherwise) were cooled at different rates after reflow soldering on the Cu pad above 250°C for 60 sec. Three different media of cooling were used to control cooling rates: fast water quenching, medium cooling on an aluminum block, and slow cooling in furnace. Both the solder composition and cooling rate after reflow have a significant effect on the intermetallic compound (IMC) thickness (mainly Cu₆Sn₅). Under fixed cooling condition, alloys (1), (3), and (5) revealed larger IMC thicknesses than that of alloys (2) and (4). Slow cooling produced an IMC buildup of thicker than 10 μm, while medium and fast cooling produced a thickness of thinner than 5 μm. The inverse relationship between IMC thickness and shear strength was confirmed. All the fast- and medium-cooled joints revealed a ductile mode (fracture surface was composed of the β-Sn phase), while the slow-cooled joints were fractured in a brittle mode (fracture surface was composed of Cu₆Sn₅ and Cu₃Sn phases). The effect of isothermal aging at 130°C on the growth of the IMC, shear strength, and fracture mode is also reported.     

The effect of intermetallic compound morphology on Cu diffusion in Sn-Ag and Sn-Pb solder bump on the Ni/Cu Under-bump metallization

The eutectic Sn-Ag solder alloy is one of the candidates for the Pb-free solder, and Sn-Pb solder alloys are still widely used in today’s electronic packages. In this tudy, the interfacial reaction in the eutectic Sn-Ag and Sn-Pb solder joints was investigated with an assembly of a solder/Ni/Cu/Ti/Si₃N₄/Si multilayer structures. In the Sn-3.5Ag solder joints reflowed at 260°C, only the (Ni_1−x,Cu_x)₃Sn₄ intermetallic compound (IMC) formed at the solder/Ni interface. For the Sn-37Pb solder reflowed at 225°C for one to ten cycles, only the (Ni_1−x,Cu_x)₃Sn₄ IMC formed between the solder and the Ni/Cu under-bump metallization (UBM). Nevertheless, the (Cu_1−y,Ni_y)₆Sn₅ IMC was observed in joints reflowed at 245°C after five cycles and at 265°C after three cycles. With the aid of microstructure evolution, quantitative analysis, and elemental distribution between the solder and Ni/Cu UBM, it was revealed that Cu content in the solder near the solder/IMC interface played an important role in the formation of the (Cu_1−y,Ni_y)₆Sn₅ IMC. In addition, the diffusion behavior of Cu in eutectic Sn-Ag and Sn-Pb solders with the Ni/Cu UBM were probed and discussed. The atomic flux of Cu diffused through Ni was evaluated by detailed quantitative analysis in an electron probe microanalyzer (EPMA). During reflow, the atomic flux of Cu was on the order of 10¹⁶−10¹⁷ atoms/cm²sec in both the eutectic Sn-Ag and Sn-Pb systems.