Control over the surface plasmon band of block copolymer/Ag/Au nanoparticles composites by the addition of single walled carbon nanotubes

In this study, we demonstrate control over the localized surface plasmon band (SPB) of a micellar poly(styrene-block-4vinylpyridine) (PS-b-P4VP) copolymer thin film composite that includes Ag and Au nanoparticles (NPs) in the presence of single walled carbon nanotubes (SWCNTs). Ag and Au NPs are preferentially located in the P4VP core and the PS corona of ordered spherical PS-b-P4VP copolymer micelles, respectively. This structure gave rise to a single SPB due to the coupling of Ag and Au SPBs. The non-covalent addition of SWCNTs in the block copolymer micelles shifts the coupled SPB to a lower wavelength. The maximum shift in the coupled SPB of approximately 30 nm was achieved in the PS-b-P4VP/Ag/Au NPs composite. The carbon nanotube induced modulation of the coupled SPB stems from the charge accumulation effect of the SWCNTs placed between the two types of nanoparticles.     

Selective distribution of interacting magnetic nanoparticles into block copolymer domains based on the facile inversion of micelles

We demonstrate a simple methodology to incorporate interacting magnetic nanoparticles (mNPs) into cylinder forming block copolymer templates. Poly(styrene-block-isoprene) (PS-b-PI) with PI cylinders and poly(styrene-block-4vinylpyridine) (PS-b-P4VP) with PS cylinders were used as the block copolymer templates and γ-Fe₂O₃ NPs coated with oleic acids were pre-synthesized for the interacting mNPs. Regardless of the template block copolymers, the selective location of mNPs and the size of mNP aggregates are clearly altered by changing casting solvents. When good solvents for both blocks were used as casting solvents, mNPs are readily aggregated during the solvent evaporation. In contrast, under selective casting solvents for the minor blocks, the mNPs were selectively trapped into the cylinder domains through the facile inversion of micelles during solvent evaporation. The interplay between mNPs and block copolymers was also tested with different molecular weights of block copolymers.     

Shell-core-corona aggregates formed from poly(styrene)-poly(4-vinylpyridine) block copolymer induced by added homopolymer via interpolymer hydrogen-bonding

The solution behavior of poly(styrene)-poly(4-vinylpyridine) (PS-b-P4VP) block copolymer with added poly(4,4′-oxydiphenylenepyromellitamic acid) (POAA) homopolymer in DMF is studied by dynamic light scattering (DLS), nuclear magnetic resonance (NMR), and transmission electron microscopy (TEM). It is found that coaggregation takes place when mixing PS-b-P4VP block copolymer and POAA homopolymer in DMF due to the strong interpolymer hydrogen-bonding between POAA chains and P4VP blocks. The coaggregation is a diffusion-controlled process and the complexation-induced aggregates are very stable. NMR measurements demonstrate that the resultant aggregates are much more swollen compared with typical amphiphilic block copolymer core-shell micelles. DLS measurements with Eu³⁺ as a probe combined with TEM observation, are employed to study the structure of the aggregates. Results reveal that the formed aggregates are core-shell spheres with the P4VP/POAA complexes as core and the PS blocks as shell when the weight ratio of POAA to PS-b-P4VP is lower. However, a core-shell-corona structure forms with a thin layer of POAA chains adsorbed on the initial core-shell aggregates with increasing weight content of POAA to 60%. Finally, possible mechanisms of the structural transitions are proposed.     

Low dielectric constant nanoporous poly(methyl silsesquioxane) using poly(styrene-block-2-vinylpyridine) as a template

Low dielectric constant nanoporous poly(methyl silsesquioxane) (PMSSQ) was prepared through the templating of an amphiphilic block copolymer, poly(styrene-b-2-vinylpyridine) (PS-b-P2VP). The experimental and theoretical studies suggest that the intermolecular hydrogen bonding interaction is existed between the PMSSQ precursor and PS-b-P2VP. The result of modulated differential scanning calorimeter (MDSC) indicates the miscible hybrid of the PMSSQ precursor/PS-b-P2VP. The miscible hybrid and the narrow thermal decomposition of the PS-b-P2VP lead to nanopores in the prepared films from the results of transmission electronic microscopy (TEM), atomic force microscopy (AFM), and small angle X-ray scattering (SAXS). The effects of the loading ratio and the PS block volume ratio (f_PS: 0.74, 0.46 and 0.35) on the morphology and properties of the prepared nanoporous PMSSQ films were investigated. The AFM and TEM studies suggest that the uniform pore morphology should be prepared from a modest porogen loading level for the optimum intermolecular hydrogen bonding. The PS-b-P2VP with a smaller f_PS requires a higher loading level to obtain the uniform pores. The refractive index and dielectric constant of the prepared nanoporous films could be tuned by the loading ratio in the range of 1.361-1.139 and 2.359-1.509, respectively. However, both properties are independent of the f_PS. The prepared study demonstrates the control of the morphology and properties of the nanoporous films through the polymer structure.     

Dispersion of polymer-grafted magnetic nanoparticles in homopolymers and block copolymers

The dispersion of magnetic nanoparticles (NPs) in homopolymer poly(methyl methacrylate) (PMMA) and block copolymer poly(styrene-b-methyl methacrylate) (PS-b-PMMA) films is investigated by TEM and AFM. The magnetite (Fe₃O₄) NPs are grafted with PMMA brushes with molecular weights from M = 2.7 to 35.7 kg/mol. Whereas a uniform dispersion of NPs with the longest brush is obtained in a PMMA matrix (P = 37 and 77 kg/mol), NPs with shorter brushes are found to aggregate. This behavior is attributed to wet and dry brush theory, respectively. Upon mixing NPs with the shortest brush in PS-b-PMMA, as-cast and annealed films show a uniform dispersion at 1 wt%. However, at 10 wt%, PS-b-PMMA remains disordered upon annealing and the NPs aggregate into 22 nm domains, which is greater than the domain size of the PMMA lamellae, 18 nm. For the longest brush length, the NPs aggregate into domains that are much larger than the lamellae and are encapsulated by PS-b-PMMA which form an onion-ring morphology. Using a multi-component Flory-Huggins theory, the concentrations at which the NPs are expected to phase separate in solution are calculated and found to be in good agreement with experimental observations of aggregation.     

Hexagonally ordered arrays of metallic nanodots from thin films of functional block copolymers

We demonstrate a new and simple route to fabricate highly dense arrays of hexagonally close packed inorganic nanodots using functional diblock copolymer (PS-b-P4VP) thin films. The deposition of pre-synthesized inorganic nanoparticles selectively into the P4VP domains of PS-b-P4VP thin films, followed by removal of the polymer, led to highly ordered metallic patterns identical to the order of the starting thin film. Examples of Au, Pt and Pd nanodot arrays are presented. The affinity of the different metal nanoparticles towards P4VP chains is also understood by extending this approach to PS-b-P4VP micellar thin films. The procedure used here is simple, eco-friendly, and compatible with the existing silicon-based technology. Also the method could be applied to various other block copolymer morphologies for generating 1-dimensional (1D) and 2-dimensional (2D) structures.     

The fabrication of graphitic thin films with highly dispersed noble metal nanoparticles by direct carbonization of block copolymer inverse micelle templates

Ordered arrays of Au or Ag nanoparticles supported on two-dimensional graphitic carbon films were prepared by direct carbonization of stabilized asymmetric polystyrene-block-poly(4-vinyl pyridine) (PS-b-P4VP) inverse micellar films loaded with metal precursors. Crosslinked PS-b-P4VP thin film templates with metal precursors selectively distributed in P4VP domains were converted to carbonaceous thin films having well-defined, highly dispersed metal nanoparticle (NP) arrays by ultraviolet (UV) irradiation under vacuum and subsequent carbonization. Mesoporous carbon films were also obtained after extracting the metal NPs by sonication in selected solvents. PS-b-P4VP was employed not only as carbon source, but also as template for introducing metal NPs in a nanopatterned configuration. The characteristic features and properties of thus generated hybrid carbon nanostructures were investigated by microscopy, UV–visible spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction measurement, and Raman spectroscopy.     

A new approach in the study of tethered diblock copolymer surface morphology and its tethering density dependence

A poly(l-lactic acid)-block-polystyrene-block-poly(methyl methacrylate) (PLLA-b-PS-b-PMMA) triblock copolymer was synthesized with a crystalline PLLA end block. Single crystals of this triblock copolymer grown in dilute solution could generate uniformly tethered diblock copolymer brushes, PS-b-PMMA, on the PLLA single crystal substrate. The diblock copolymer brushes exhibited responsive, characteristic surface structures after solvent treatment depending upon the quality of the solvent in relation to each block. The chemical compositions of these surface structures were detected via the surface enhanced Raman scattering technique. Using atomic force microscopy, the physical morphologies of these surface structures were identified as micelles in cyclohexane and “onion”-like morphologies in 2-methoxyethanol, especially when the PS-b-PMMA tethered chains were at low tethering density.     

Photocrosslinkable acid urethane dimethacrylates from renewable natural oil and their use in the design of silver/gold polymeric nanocomposites

Castor oil-based acid urethane macromers were prepared and employed for obtaining Ag/Au/polymer nanocomposites. Structure and UV induced photopolymerization of the macromers were investigated by spectral methods. The polymerization rate and the degree of conversion decreased with about 10% in the presence of 2.5 wt.% silver nanoparticles (Ag NPs). For the diacid macromer, the surface plasmon intensity increased with irradiation time (the optical density of the absorption maximum (430 nm) attained 2.3 after 600 s), whereas a diminished efficiency was found for Ag NPs in situ generated. Transmission electron microscopy and X-ray photoelectron spectroscopy confirmed uniform distribution of the spherical nanoparticles (0.6 nm (Ag NPs); 5 nm (Au NPs)) and the appearance of Ag 3d_3/2, Ag 3d_5/2, Au 4f_7/2 and Au 4f_5/2 peaks corresponding to Ag (0) or Au (0). Environmental scanning electron microscope with energy-dispersive X-ray detector, contact angle and mechanical parameters measurements complemented the above observations.     

Surface morphology evolution of poly(styrene-block-4-vinylpyridine) (PS-b-P4VP)(H) and poly(methyl methacrylate)-dibenzo-18-crown-6-poly(methyl methacrylate) (PMCMA) supramolecular film

Well-ordered nanostructured polymeric supramolecular thin films were fabricated from the supramolecular assembly of poly(styrene-block-4-vinylpyridine) (PS-b-P4VP)(H⁺) and poly(methyl methacrylate)-dibenzo-18-crown-6-poly(methyl methacrylate) (PMCMA). A depression of cylindrical nanodomains was formed by the block of P4VP(H⁺) and PMCMA associates surrounded by PS. The repulsive force aroused from the incompatibility between the block of P4VP(H⁺) and PMCMA was varied through changing the molecule weight (M_w) of PMCMA, the volume fraction of the block of P4VP(H⁺), and annealing the film at high temperature. Increasing the repulsive force led to a change of overall morphology from ordered nanoporous to featureless structures. The effects of solvent nature and evaporation rate on the film morphology were also investigated. Further evolution of surface morphologies from nanoporous to featureless to nanoporous structures was observed upon exposure to carbon bisulfide vapors for different treatment periods. The wettability of the film surface was changed from hydrophilicity to hydrophobicity due to the changes of the film surface microscopic composition.     

Nanostructure and hydrogen bonding in interpolyelectrolyte complexes of poly(?-caprolactone)-block-poly(2-vinyl pyridine) and poly(acrylic acid)

Nanostructured poly(?-caprolactone)-block-poly(2-vinyl pyridine) (PCL-b-P2VP)/poly(acrylic acid) (PAA) interpolyelectrolyte complexes (IPECs) were prepared by casting from THF/ethanol solution. The morphological behaviour of this amphiphilic block copolymer/polyelectrolyte complexes with respect to the composition was investigated in a solvent mixture. The phase behaviour, specific interactions and morphology were investigated using differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, optical microscopy (OM), dynamic light scattering (DLS) and atomic force microscopy (AFM). Micelle formation occurred due to the aggregation of hydrogen bonded P2VP block and polyelectrolyte (PAA) from non-interacted PCL blocks. It was observed that the hydrodynamic diameter (D_h) of the micelles in solution decreased with increasing PAA content up to 40 wt%. After 50 wt% PAA content, D_h again increased. The micelle formation in PCL-b-P2VP/PAA IPECs was due to the strong intermolecular hydrogen bonding between PAA homopolymer units and P2VP blocks of the block copolymer. The penetration of PAA homopolymers into the shell of the PCL-b-P2VP block copolymer micelles resulted in the folding of the P2VP chains, which in turn reduced the hydrodynamic size of the micelles. After the saturation of the shell with PAA homopolymers, the size of the micelles increased due to the absorption of added PAA onto the surface of the micelles.     

Negative differential resistance and improved optoelectronic properties in Ag nanoparticles-decorated graphene oxide–riboflavin hybrids

Silver nanoparticles (Ag NPs) are decorated on graphene oxide (GO)–riboflavin (R) hybrids produced with three different compositions. The SEM micrographs of the GO–R–Ag materials show a helical fibrillar morphology different from the bar and wrinkled sheet morphology of R and GO, respectively. FT-IR spectra indicate that GO produces a supra molecular complex with R and Ag NPs are stabilized by both R and GO. The UV–vis spectra show a large shift of surface plasmon band from 390 to 570 nm and the circular dichroism spectra indicate a drastic change in the GO–R–Ag system over the GO–R system for a weight ratio of GO to R of 13, suggesting that Ag NPs are wrapped by both the GO–R hybrid and R moieties. The PL-intensity of R increases in the GO–R hybrids but it decreases in the GO–R–Ag ones. The dc-conductivity of the GO–R hybrids increases by 2–3 orders of magnitude on addition of Ag NPs. The I–V characteristic curves of the GO–R–Ag (GO/R = 1/3) material shows a negative differential resistance. Possible reasons from the charge trapping on the Ag NPs followed by stabilization by R are discussed and a model using the density of states approach is proposed.     

Biomimetic fabrication of mulberry-like nano-hydroxyapatite with high specific surface area templated by dual-hydrophilic block copolymer

Novel porous and mulberry-like hydroxyapatite (HAp) nanoparticles with three-dimensionally hierarchical microstructures were developed by using the dual-hydrophilic block copolymer poly(methacrylate acid)-b-poly[N-(2-methacryloylxyethyl) pyrrolidone] (PMAA-b-PNMP) as the template. It was found that the morphology and Ca/P ratio of synthesized HAp was highly related to the concentration of block copolymer and solution pH, respectively. The morphological evolution of HAp nanoparticles in different conditions was investigated systematically by scanning electron microscopy (SEM), transmission electron microscope (TEM), high-resolution transmission electron microscope (HRTEM), powder X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The possible mechanism of PMAA-b-PNMP assisted mulberry-like HAp formation was also proposed based on the time-dependent TEM results. Attributing to the high specific surface area (SSA) of 119 m² g⁻¹, these mulberry-like HAp nanoparticles exhibited excellent adsorption ability for Congo Red (CR). The maximum adsorption capacity was 467 mg g⁻¹ according to the Langmuir monolayer adsorption model.     

Synthesis and chemosensory properties of terpyridine-containing diblock polycarbazole through RAFT polymerization

This paper describes the synthesis of a terpyridine-containing diblock copolymer, poly(N-vinylcarbazole)-block-poly[4′-((4-vinylphenyl) phenyl)-2,2′:6′,2″- terpyridine] (poly(VK₁₅-b-TPY₄)), using the macro-chain transfer agent VK macro-CTA, and employing two-step reverse addition-fragmentation transfer (RAFT) polymerization. We examined the effect of terpyridine units on sensory characteristics of fluorescent chemosensors. VK macro-CTA and diblock copolymer poly(VK₁₅-b-TPY₄) both exhibited moderate thermal stability, with thermal decomposition temperatures of 5% weight losses at approximately 307 °C and 378 °C, respectively, suggesting that the enhancement of thermal stability was attributed to the incorporation of terpyridine segments into the block copolymer. Poly(VK₁₅-b-TPY₄) exhibited higher sensitivities to Ni^2 + and Mn^2 + ions, with Stern–Volmer constants (K_sv) of 2.58 × 10⁵ M^− 1 and 2.57 × 10⁵ M^− 1, respectively. Adding a Zn^2 + ion not only caused partial fluorescence enhancement (3.2-fold quantum efficiency) but also induced a bathochromic shift of emission peak by approximately 56 nm (from 429 nm to 485 nm), indicating that the Zn^2 +-terpyridine complex reduced the twist and vibration of the C–C polymer backbone and enhanced the charge transfer from donors to acceptors because of the more planar and rigid structure. Our results suggest that poly(VK₁₅-b-TPY₄) is a promising material for chemosensory applications.     

Re-assembly behaviors of polystyrene-b-poly(acrylic acid) micelles

The re-assembly behaviors of spherical micelles of the polystyrene-b-poly(acrylic acid) (PS-b-PAA) diblock copolymer in different solvent mixtures were investigated using dynamic light scattering, transmission electron microscopy and atomic force microscopy. Depending on the nature of the solvent, PS-b-PAA micelles re-assembled from spheres to nanorings in toluene or to necklace-like aggregates in water induced by solvent evaporation. Systematic studies suggested that the re-assembly behaviors on a neutral surface are strongly correlated with the micellar surface components, the solvent polarity and the chain length of the micelle corona of the solvated blocks. We proposed that the formation of nanorings from PS-b-PAA micelles in toluene is mainly induced by the dewetting process of the solvent, while the necklace-like structure arises from the hydrogen bonding interactions among the partially dissociated PAA units.     

Design and stabilization of block copolymer micelles via phenol-pyridine hydrogen-bonding interactions

A new approach for the preparation of block copolymer micelles in non-selective solvent is introduced. Phenol-pyridine hydrogen-bonding interactions are used for the first time to prepare core-shell micelles in non-selective solvents using block copolymers and bifunctional low-molecular-weight hydrogen-bonding crosslinkers. Poly(styrene-b-4-vinylphenol)/Bis-pyridyl ethane and poly(styrene-b-4-vinylpyridine)/Bisphenol A were investigated as micelle formation due to phenol-pyridine hydrogen bond crosslinking. The influence of several factors such as temperature, concentration, solvent and pH in micellization-demicellization process was analyzed by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), dynamic light scattering (DLS) and atomic force microscopy (AFM). This method opens new possibilities to the generation of block copolymer micelles in non-selective solvents.     

Anisotropic Conductivity of Diblock Copolymer Films

The first part of this article reviews the orientation of the surface and the in-bulk microdomain structures of diblock copolymers. Well-defined poly(styrene-b-2-vinylpyridine) diblock copolymers (about 50 wt% polystyrene blocks) formed horizontally oriented lamellar microdomains when these copolymers were cast from a nonselective solvent by means of the air–copolymer and substrate–copolymer interactions. The second section reviews the preparation of semiconducting materials by the exposure of these films to alkyl dihalide vapor. This film had an anisotropic conductivity with about 8 orders of magnitude. The third section reviews the construction of ionic complex phases by an ion-exchange reaction of quaternized poly(2-vinylpyridine) (P2VP) layers with lithium perchlorate. Finally, the introduction of colloidal silver into quaternized P2VP layers by reduction of silver iodide is reported. High electrical anisotropy originated in the orientation of microphase-separated structure of diblock copolymer films.     

Vesicle formation of polystyrene-block-poly (ethylene oxide) block copolymers induced by supercritical CO2 treatment

A novel route for a preparation of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) block copolymer vesicles induced by supercritical carbon dioxide (scCO₂) is demonstrated. When PS-b-PEO block copolymer solutions in tetrahydrofuran (THF) are treated with scCO₂ at 70 °C for different times, PS-b-PEO copolymers first assemble into aggregated spheres; then aggregated spheres change into large compound micelles and finally evolve into vesicles. The possible formation mechanism of the vesicles is discussed.     

Extraordinary mechanical flexibility in composite thin films composed of bimetallic AgPt nanoparticle-decorated multi-walled carbon nanotubes

Flexible, transparent, and conducting composite thin films, constructed from multi-walled carbon-nanotube-supported silver–platinum alloy nanoparticles (AgPt–MWCNT) on a flexible polyethylene terephthalate (PET) substrate through the combination of a two-step polyol process for synthesizing composites of carbon nanotubes (CNTs) and metallic nanoparticles (NPs) with an ultrasonic atomization-spin coating method for preparing thin films, have been fabricated. AgPt NPs with an average size of approximately 26 nm were uniformly attached to the sidewalls of MWCNTs to form an effective and strongly mechanical conductive network. These composites were then exposed to microwave plasma irradiation, which can lower the contact resistance between the metallic NPs and CNTs and reinforce the network bridges. The resulting AgPt–MWCNT–PET thin films exhibit improved optoelectronic and mechanical properties, and they possess a sheet resistance of 154 Ω/sq with a transmittance of 80% at 550 nm. These values are competitive with those of most other CNT-based films. Most importantly, the corresponding sheet conductivity does not decrease even after 500 bending cycles. Therefore, the as-produced AgPt–MWCNT–PET films may be direct alternatives to indium tin oxide and other transparent conducting oxide films.     

Preparation and antibacterial activity of Ag/SiO2 thin film on glazed ceramic tiles by sol–gel method

In the present study, silver-doped silica thin films on glazed surface of ceramic tiles were well prepared by sol–gel method to achieve antibacterial activity. Thermal treatment was done in the air at 1100 °C for two hours. The Ag/SiO₂ thin films were investigated through Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD) and wavelength dispersive spectrometry (WDS). Atomic absorption spectroscopy (AAS) was used for the quantitative determination of the silver ion concentration being released from Ag/SiO₂ films over a 24 day period. The antibacterial effects of Ag/SiO₂ thin films against Escherichia coli and Staphylococcus aureus were also examined. From the analysis results, it was found that high temperature treated coating consists of two phases of SiO₂ and Ag based on the trapping of the Ag phase in the silica matrix. The presence of Ag elements on the surface of the coated tiles, were also observed. Thermal treatment at high temperatures caused sharp XRD peaks and high crystallinity in this system. Ag⁺ ions were released constantly and the mean release rate (±SD) was 0.104 ±0.01 μg/ml during 24 days. Coating films exhibited an excellent antibacterial performance against both bacterium.