Thermodynamic analysis of two-component,two-phase flow in solar collectors with application to a direct-expansion solar-assisted heat pump

Two-phase flow of pure chlorofluorocarbon (CFC) refrigerants in solar collector tubes has been examined in previous studies in connection with applications in direct-expansion, solar-assisted heat pumps (DX-SAHP). The present work extends the thermodynamic analysis of solar collectors to the multicomponent and multiphase domain to cover newly proposed refrigerant mixtures which are potential candidates for replacing CFCs in future DX-SAHP systems. A computational methodology is developed to determine the size of a solar collector of a DX-SAHP that uses a binary refrigerant mixture whose thermodynamic and transport properties are predicted from a computer code. The energy equation for the elemental collector tube control volume, incorporating the local thermodynamic and heat transfer characteristics, is integrated to determine the tube length for a given set of inlet and exit thermodynamic states of the refrigerant mixture. Effects of various parameters such as the collector mass-flow rate and operating pressure, tube diameter and absorbed solar radiation on the collector tube length, heat transfer coefficient, and the local refrigerant temperature in the tube are also considered.     

直膨式太阳能热泵微通道集热/蒸发器制冷剂分布特性

为研究微通道集热/蒸发器内制冷剂分布及对直膨式太阳能热泵系统性能的影响,搭建以丙烷（R290）为制冷剂的系统实验平台。基于实验数据,提出一种利用红外成像技术分析微通道集热/蒸发器内两相态制冷剂分布的方法,获得了电子膨胀阀开度、太阳辐射强度以及环境温度对集热/蒸发器内两相态制冷剂分布情况的影响特性。结果表明：当电子膨胀阀开度由20%增至60%时,集热/蒸发器的制冷剂分布参数（RDP）提高10.6%,系统性能系数（COP）从2.8升至5.5。较高的太阳辐射强度或环境温度可有效避免制冷剂回流现象。     

Modeling and application of direct-expansion solar-assisted heat pump for water heating in subtropical Hong Kong

Direct hot water production consumes about 4% of the total energy use in Hong Kong, and about 20% when considering only the domestic sector. For water heating the energy sources are mostly town gas, liquefied petroleum gas and electricity. The use of heat pump or solar water heating, particularly the solar-assisted heat pump options, is not popular. In this paper, the potential application of a unitary type direct-expansion solar-assisted heat pump (DX-SAHP) system was examined. A numerical model of the DX-SAHP system was first introduced. From the simulation results with the use of the Typical Meteorological Year (TMY) weather data of Hong Kong, the system was found achieving a year-average coefficient of performance (COP) of 6.46, which is much better than the conventional heat pump system performance. The potential use of DX-SAHP therefore deserves further evaluation.     

Transient simulation of a capacity-modulated, direct-expansion, solar-assisted heat pump

The long-term thermal performance of a direct-expansion, solar-assisted heat pump is determined from the transient simulation of the system. The system employs a bare collector that also acts as the heat pump evaporator. Of particular interest in this study is the configuration in which the compressor and the collector area are properly matched from the long-term thermal performance point of view. This matching is achieved through multistep as well as two-step compressor capacity modulation. In addition to examining the effects of compressor capacity modulation, the effects of various system parameters such as collector area, storage volume, load temperature, wind speed, collector slope, and refrigerant properties are also studied in detail.Monthly averaged thermal performance parameters such as the heat pump system coefficient of performance are determined by executing a computer simulation program that uses the typical meterological year (TMY) solar data for Norfolk, Virginia. Results indicate that the system performance is governed strongly by collector area, compressor RPM, load temperature, and refrigerant properties. The remaining parameters have only weak influence on the long-term system performance of direct expansion solar-assisted heat pump (SAHP) system considered in this study.     

Heat-pipe enhanced solar-assisted heat pump water heater

A heat-pipe enhanced solar-assisted heat pump water heater (HPSAHP) is studied. HPSAHP is a heat pump with dual heat sources that combines the performance of conventional heat pump and solar heat pipe collector. HPSAHP operates in heat-pump mode when solar radiation is low and in heat-pipe mode without electricity consumption when solar radiation is high. HPSAHP can thus achieve high energy efficiency. A prototype was designed and built in the present study. An outdoor test for a HPSAHP in the present study has shown that COP of the hybrid-mode operation can reach 3.32, an increase of 28.7% as compared to the heat-pump mode COP (2.58).     

A solar-assisted heat pump system for heating and cooling residences

A significant impact of solar energy applications on the total energy demand requires systems or devices which can be retrofitted to existing energy users. The all-electric residence unit, which includes about 10 per cent of all such units in the U.S.A. and constitutes over half of those completed in 1973, seems particularly suited to a solar modification. It is proposed that heating and cooling of the all-electric residence unit be accomplished by using a solar-assisted heat-pump system. The proposed system makes use of a conventional air-conditioning unit which would be modified by fitting controls to reverse the flow of refrigerant for the heating mode and by changing the outdoor heat exchanger from refrigerant-to-air to refrigerant-to-water. In addition, there would be provided a solar collector and two insulated water-storage tanks. Water from one tank would be circulated through the refrigerant-to-water heat exchanger when needed and then returned to the other tank, so that essentially a source of heat of constant temperature would be maintained, thus decreasing the temperature interval for the heat pump and thereby saving energy. In the cooling mode the stored water would be cooled by exposure of the solar collector to the night sky to decrease the temperature interval for the heat pump, thereby reducing energy consumption. Calculations were made for an existing residence unit for which the total energy input is known and to which the proposed solar-assisted heat-pump system is applied. An estimated cost of equipment and of its operation is compared with the cost of owning and operating fuel and electrically heated systems. It is concluded that the solar-assisted heat-pump system with current fuel prices can provide immediate economic benefit over the all-electric home and is possibly on par with residences using fuel oil or liquefied petroleum gas, but it yields higher cost over systems using natural gas. The effect of a two-phase expander to replace the expansion valve in the refrigerant circuit has been theoretically investigated. It shows a significant energy saving worthy of further economic and practical consideration.     

Analysis of a direct expansion solar assisted heat pump using different refrigerants

The thermal performance of a direct expansion solar assisted heat pump (DX-SAHP) is analyzed for several refrigerants using two collector configurations, namely a bare collector and a one cover collector. The REFPROP computer program, developed by the National Institute of Science and Technology, is employed to predict the refrigerant properties involved in the energy balance across the collector. The thermal performance, as characterized by the coefficient of performance (COP), is determined for a variety of pure refrigerants as well as refrigerant mixtures. The performance degradation due to switching from R-12 to pure hydrofluorocarbon (HFC) refrigerants as well as refrigerant blends is investigated. A graphical procedure is developed and illustrated for several refrigerants for sizing the solar collector area and the heat pump compressor displacement capacity for the two collector configurations considered in this study.     

Advances in liquid based photovoltaic/thermal (PV/T) collectors

In order to get more power and heat from PV/T system, it is necessary to cool the PV cell and decrease its temperature. This is not an easy task especially in hot and humid climate areas. There is a lack of an effective cooling strategy of PV/T panels. The liquid based photovoltaic thermal collector systems are practically more desirable and effective than air based systems. Temperature fluctuation in liquid based PV/T is much less than the air based PV/T collectors which subjected to variation in solar radiation levels. In this study a review of the available literature on PV/T collector systems which utilize water and refrigerant (working fluid) as heat removal medium for different applications has been conducted. Future direction of water-cooled and refrigerant hybrid photovoltaic thermal systems was presented. This study revealed that the direct expansion solar-assisted heat pump system achieved better cooling effect of the PV/T collector.     

Experimental investigation and a dynamic simulation of the solar-assisted energy-storaged heat pump system

In order to improve the performance of the solar-assisted and energy-storaged heat pump system, an experimental setup was constructed. In this study, the solar-assisted energy-storaged series heat pump system and other conventional heat pump systems with no energy storage (series and parallel heat pump systems) are experimentally investigated and compared. The experiments were made in July, August, September, October, November, and December in 1990, under the clear-sky conditions for three heat pump systems. The experimentally obtained results are used to calculate the collector efficiency n_k, heat pump COP, and system COP_sys (coefficient of performance). On the other hand, a dynamic simulation program has been developed for a solar-assisted and energy-storaged heat pump system. The experimental results were compared with the dynamic simulation results.     

Energy and exergy performance assessment of a novel solar-based integrated system with hydrogen production

In this study, a new solar power assisted multigeneration system designed and thermodynamically analyzed. In this system, it is designed to perform heating, cooling, drying, hydrogen and power generation with a single energy input. The proposed study consists of seven sub-parts which are namely parabolic dish solar collector, Rankine cycle, organic Rankine cycle, PEM-electrolyzer, double effect absorption cooling, dryer and heat pump. The effects of varying reference temperature, solar irradiation, input and output pressure of high-pressure turbine and pinch point temperature heat recovery steam generator are investigated on the energetic and exergetic performance of integration system. Thermodynamic analysis result outputs show that the energy and exergy performance of overall study are computed as 48.19% and 43.57%, respectively. Moreover, the highest rate of irreversibility has the parabolic dish collector with 24,750 kW, while the lowest rate of irreversibility is calculated as 5745 kW in dryer. In addition, the main contribution of this study is that the solar-assisted multi-generation systems have good potential in terms of energy and exergy efficiency.     

Experimental studies on a ground coupled heat pump with solar thermal collectors for space heating

This paper presents experimental studies on a solar-assisted ground coupled heat pump (SAGCHP) system for space heating. The system was installed at the Hebei Academy of Sciences in Shijiazhuang (lat. N38°03′, long. E114°26′), China. Solar collectors are in series connection with the borehole array through plate heat exchangers. Four operation modes of the system were investigated throughout the coldest period in winter (Dec 5th to Dec 27th). The heat pump performance, borehole temperature distributions and solar colleting characteristics of the SAGCHP system are analyzed and compared when the system worked in continuous or intermittent modes with or without solar-assisted heating. The SAGCHP system is proved to perform space heating with high energy efficiency and satisfactory solar fraction, which is a promising substitute for the conventional heating systems. It is also recommended to use the collected solar thermal energy as an alternative source for the heat pump instead of recharging boreholes for heat storage because of the enormous heat capacity of the earth.     

基于PVT集热/蒸发器的补气增焓热泵性能分析

传统直膨式太阳能辅助热泵系统在低温环境适应性欠佳,影响其在寒冷地区使用,通过采用补气增焓技术可以有效提高其低温条件下的供热能力。以所提出的采用PVT集热/蒸发器的补气增焓热泵系统为研究对象,计算分析环境条件、太阳辐射强度、注入蒸汽质量流量对该热泵系统性能的影响。研究结果表明： 当环境温度为-10℃,太阳照强度为500 W/m²时,性能系数（COP）可达4.3,比使用补气增焓（VI）循环的空气源热泵（ASHP）系统高63.6%。以当量热价（LCOH）作为指标与其他3种供热系统进行比较,所提出的系统经济性也具有一定的优势,可为补气增焓热泵系统在寒冷气候地区的应用提供新思路。     

Optimization study on a solar-assisted air source heat pump system with energy storage based on the economics method

Currently, hybrid renewable energy systems with thermal energy storage have various advantages and are widely used. This paper investigated the performance of a solar-assisted air source heat pump system with energy storage (SASHPS-ES) in Beijing, China, and proposed an optimal operation mode based on economic evaluation. The results indicate that with the optimal heat storage ratio of 50%, the rated capacity of the air source heat pump (ASHP) of the SASHPS-ES system can be reduced by 16.7%, decreasing its annual total cost by 26.5% under a peak-valley electricity price policy. The price of 620¥/m² is critical for the solar collectors. The economics of SASHPS-ES is better than that of an air source heat pump system with energy storage (ASHPS-ES) when the price of the selected solar collector units is less than this critical price (without subsidies from the government). In the current local market, the promotion of SASHPS-ES systems and other solar energy applications requires government subsidies for a period of time. The results can guide the utilization and popularity of SASHPS-ES in China.     

Economic comparison of solar-assisted heat pumps

A study of the economic performance of a solar system, air-to-air heat pumps, and several solar-assisted heat pump systems (SAHP) for residential heating is presented. The study is based on a computer simulation which is supported by monitoring data from an existing installation, the Terrosi-Grumman house in Quechee, Vermont. Three different SAHP configurations as well as conventional solar and air-to-air heat pump systems are evaluated for a northern New England climate. All systems are evaluated both with and without a peak/off-peak electricity price differential.

The SAHP systems are: (1) the series system in which the solar storage serves as the energy source for the heat pump, (2) the series off-peak system in which the heat pump in the series system operates only during certain periods of the day under a special electric rate structure, (3) a parallel system in which the environment is the source for both the collector and the heat pump, and (4) a peak/off-peak parallel system in which oil is operated during the period of peak electricity price. Hybrid air-to-air heat pump/oil systems are also evaluated.

For all alternatives, two different economic analyses are used: (1) the rate of return which emphasizes the return earned on the capital investment, and (2) the life cycle critical price which compares the current capital cost to the present worth of the stream of all future energy savings.

Both economic measures select the air-to-air heat pump/on-peak oil system when there is a peak/off-peak electricity price differential. (In this case the ratio of off-peak to average price is 40 per cent.) When there is no price differential, the air-to-air heat pump/oil system is still preferred, but the oil system is now operated when the ambient temperature falls below −6.7°C (20°F). When the electricity price is doubled (from 19.5 to 40$/GJ), solar/oil is the preferred system.     

Solar-assisted heat pump system and in-ground energy storage in a school building

An experimental solar-assisted heat pump system with a hybrid ground-coupled storage at the F.U.L. in Arlon, Belgium, is described. It includes a 382 m² solar roof, two types of water storages, heat storage in earth by horizontal exchangers, and heat pumps. One operating period (1984–1985) is analyzed. The data processed has shown that each of the subsystems has apparently performed adequately: annual collector efficiency is 0.41, heat pump C.O.P. range around 4. Despite important energy losses from the underground storage, the storage efficiency reaches 0.7. This effectiveness is mainly due to heat recovery below natural soil temperature and also to the use of buried tanks for short-term storage. The main difficulties are controlling the flow between these subsystems and developing an operating strategy that matches both the building's heat requirements and a good solar fraction.     

Performance analysis of solar-assisted chemical heat-pump dryer

A solar-assisted chemical heat-pump dryer has been designed, fabricated and tested. The performance of the system has been studied under the meteorological conditions of Malaysia. The system consists of four main components: solar collector (evacuated tubes type), storage tank, solid-gas chemical heat pump unit and dryer chamber. A solid-gas chemical heat pump unit consists of reactor, condenser and evaporator. The reaction used in this study (CaCl2-NH₃). A simulation has been developed, and the predicted results are compared with those obtained from experiments. The maximum efficiency for evacuated tubes solar collector of 80% has been predicted against the maximum experiment of 74%. The maximum values of solar fraction from the simulation and experiment are 0.795 and 0.713, respectively, whereas the coefficient of performance of chemical heat pump (COP^h) maximum values 2.2 and 2 are obtained from simulation and experiments, respectively. The results show that any reduction of energy at condenser as a result of the decrease in solar radiation will decrease the coefficient of performance of chemical heat pump as well as decrease the efficiency of drying.     

Theoretical thermal performance analysis of two solar‐assisted heat‐pump systems

The thermal performance of two different schemes of solar‐assisted heat‐pump systems has been theoretically studied. In first scheme, the evaporator of the heat pump is taken directly as the solar collecting plate and always maintained at the ambient temperature. As there is no heat loss from the collecting plate, the thermal efficiency of the collector is high and equals the solar absorptivity of the collecting plate. As suggested, the heat‐pump evaporator of the second scheme is placed in a novel fresh water solar pond/tank with high efficiency. Since the evaporator operates at a relatively high temperature, the COP of the heat pump can be increased. The calculated results show that the COP of a solar‐assisted heat pump using the second scheme is considerably higher than that of the first scheme. Copyright © 1999 John Wiley & Sons, Ltd.     

Performance of a multi-functional direct-expansion solar assisted heat pump system

This paper reports on the long-term performance of a direct-expansion solar assisted heat pump (DX-SAHP) system for domestic use, which can offer space heating in winter, air conditioning in summer and hot water during the whole year. The system employs a bare flat-plate collector array with a surface area of 10.5 m², a variable speed compressor, a storage tank with a total volume of 1 m³ and radiant floor heating unit. The performance under different operation modes is presented and analyzed in detail. For space-heating-only mode, the daily-averaged heat pump COP varied from 2.6 to 3.3, while the system COP ranged from 2.1 to 2.7. For water-heating-only mode, the DX-SAHP system could supply 200 l or 1000 l hot water daily, with the final temperature of about 50 °C, under various weather conditions in Shanghai, China. For space-cooling-only mode, the compressor operates only at night to take advantage of a utility’s off-peak electrical rates by chilling water in the thermal storage tank for the daytime air-conditioning. It shows that, the multi-functional DX-SAHP system could guarantee a long-term operation under very different weather conditions and relatively low running cost for a whole year.     

Performance characteristics of integral type solar-assisted heat pump

The characteristic of an integral type solar-assisted heat pump water heater (ISAHP) is investigated in the present study. The ISAHP consists of a Rankine refrigeration cycle and a thermosyphon loop that are integrated together to form a package heater. Both solar and ambient air energies are absorbed at the collector/evaporator and pumped to the storage tank via a Rankine refrigeration cycle and a thermosyphon heat exchanger. The condenser releases condensing heat of the refrigerant to the water side of the thermosyphon heat exchanger for producing a natural-circulation flow in the thermosyphon loop. A 105-liter ISAHP using a bare collector and a small R134a reciprocating-type compressor with rated input power 250 W was built and tested in the present study. The ISAHP was designed to operate at an evaporating temperature lower than the ambient temperature and a matched condition (near saturated vapor compression cycle and compressor exhaust temperature <100°C). A performance model is derived and found to be able to fit the experimental data very well for the ISAHP. The COP for the ISAHP built in the present study lies in the range 2.5–3.7 at water temperature between 61 and 25°C.     

太阳能电池与热泵热水器联合运行系统性能分析

为了降低太阳能光伏电池的温度,同时提升热泵热水器的蒸发温度,利用循环水路冷却太阳能光伏电池,并将热量传递给热泵热水器的蒸发器,构成联合运行系统。针对杭州市的夏季和冬季气象条件,对该联合运行系统的性能进行了计算,分析了对应不同太阳能电池温度下的系统运行参数的变化情况,包括太阳能电池发电效率和所需换热量,热泵热水器的制热量以及热泵效率等。计算结果表明,该联合运行系统能够同时提高太阳能电池光伏转换效率和热泵效率。