Necessity of biodiesel utilization as a source of renewable energy in Malaysia

In recent decades, the energy crisis and environmental issues have become a crucial problem. The rapid industrialization has lead humankind to deplete the fossil fuels and consequently the pollutant emissions have increased in the world. Many investigations have been done to find an alternative fuel to fulfill increasing energy demand. Recently, biodiesel has been introduced as an economical renewable and sustainable fuel which is cited as an environment-friendly resource. Around 350 oil-bearing crops were analyzed and some of them were capable to be considered as potential alternative fuels for diesel engines. These include virgin vegetable oils and waste vegetable oils. Rapeseed, jatropha, soybean, and palm oil are mentioned as the most common sources of biodiesel. Many countries have invested in biodiesel as an acceptable source of energy not only in research area but also in production and export. It has been proven that the biodiesel combustion characteristics are similar as petroleum. Higher ignition pressure and temperature, shorter ignition delay and higher peak release were reported in experimental combustion of biodiesel blends. Also, the efficiency of biodiesel base catalysts is more than enzymes and acid catalysts. This article is a literature review on necessity of biodiesel production as alternative fuel recourse in Malaysia and tries to illustrate the combustion characteristics and pollutant formation in biodiesel application.     

非直喷式增压柴油机燃用生物柴油的性能与排放特性

研究了非直喷式增压柴油机燃用柴油一生物柴油混合燃料的性能和排放特性。未对原机作任何调整和改动,研究了不同生物柴油掺混比例的混合燃料对功率、油耗、烟度和NOx排放的影响。结果表明：非直喷式柴油机燃用生物柴油后柴油机功率略有下降,油耗有所上升,烟度大幅下降,NOx排放增加明显。油耗、烟度和NOx的变化均与生物柴油掺混比例呈线性关系,合适的生物柴油掺混比例即可以保持柴油机的性能,又可有效地降低碳烟排放,且不引起NOx排放的显著变化。对于该增压柴油机,掺混生物柴油对外特性下的排放影响最大,影响最小的为标定转速下的负荷特性。不论是全负荷还是部分负荷,燃用生物柴油时低速下的烟度降低和NOx上升幅度均比高速时大,而同转速下高负荷时烟度降低和NOx上升更为明显。     

Impact of alternative fuel properties on fuel spray behavior and atomization

In order to verify and solve the problem of NOx and PM emissions, it is necessary to directly observe the internal combustion chamber of a diesel engine. Many studies have been performed in recent years to verify the macroscopic and microscopic behavior of the injected fuel spray because observing it is not easy due to the difficulties of the experiment. Researchers have investigated the spray characteristics for various diesel injector nozzles over a wide range of temperatures and pressure, but there is lack of evaluation for the spray characteristics for biodiesel. At a time when rapid rise of fuel prices and depleting hydrocarbon resources of the world have forced us to look for alternative fuels biodiesel produced by transesterification of non-edible vegetable oils is promising to be an important additive/substitute to petro diesel. Biodiesel being an oxygenated and sulfur-free fuel leads to more complete combustion and lower emissions. But, the energy content or net calorific value of biodiesel is less than that of diesel fuel; also it has higher viscosity and density, than diesel fuel. A considerable improvement in these properties can be obtained by mixing diesel and biodiesel and then using the blends. Biodiesel and biodiesel/petro diesel blends, with their higher lubricity levels, are increasingly being utilized as an alternative. Present paper analyzed the correlation of injection parameters that will affect the spray characteristics of biodiesel. Observations for analyzing the effect of injection parameters on spray cone angle, break up length and fuel penetration were made. Finally the performance and emissions tests were studied. Atomization and vaporization of fuel are greatly influenced by viscosity and density of fuel and these properties are temperature dependent. Thus fuel inlet temperature plays a very important role in fuel atomization process. At higher temperature viscosity of fuel decreases which enhances the atomization of biofuels.     

Performance and emission evaluation of a diesel engine fueled with methyl esters of rubber seed oil

Recent concerns over the environment, increasing fuel prices and scarcity of its supply have promoted the interest in development of the alternative sources for petroleum fuels. At present, biodiesel is commercially produced from the refined edible vegetable oils such as sunflower oil, palm oil and soybean oil, etc. by alkaline-catalyzed esterification process. This process is not suitable for production of biodiesel from many unrefined non-edible vegetable oils because of their high acid value. Hence, a two-step esterification method is developed to produce biodiesel from high FFA vegetable oils. The biodiesel production method consists of acid-catalyzed pretreatment followed by an alkaline-catalyzed transesterification. The important properties of methyl esters of rubber seed oil are compared with other esters and diesel. Pure rubber seed oil, diesel and biodiesel are used as fuels in the compression ignition engine and the performance and emission characteristics of the engine are analyzed. The lower blends of biodiesel increase the brake thermal efficiency and reduce the fuel consumption. The exhaust gas emissions are reduced with increase in biodiesel concentration. The experimental results proved that the use of biodiesel (produced from unrefined rubber seed oil) in compression ignition engines is a viable alternative to diesel.     

Theoretical modeling and experimental studies on biodiesel-fueled engine

In recent years, much research has been carried out to find suitable alternative fuel to petroleum products. The use of renewable fuels like ethanol, biogas and biodiesel in diesel engines is significant in this context. The properties of biodiesel depend on the type of the vegetable oil used for the trans-esterification process. Experimental analysis of the engine with various biodiesel and its blends requires much effort and time. Hence, a theoretical model is developed to analyze the performance characteristics of the compression ignition engine fueled by biodiesel and its blends. In the present investigation, biodiesel is produced using unrefined rubber seed oil. A two-step trans-esterification process (i.e. acid–alkaline trans-esterification) is developed for the production of methyl-esters of rubber seed oil. The properties of this biodiesel are closely matched with those of diesel fuel. The performance tests are carried out on a C.I. engine using biodiesel and its blends with diesel (B20 and B100) as fuel. The effects of relative air-fuel ratio and compression ratio on the engine performance for different fuels are also analyzed using this model. The comparison of theoretical and experimental results are presented.     

Comparison of performance characteristics of agricultural tractor diesel engine operating on home and industrially produced biodiesel

Owing to unstable diesel fuel prices in the world market, many farmers have been looking for alternative fuels. Vegetable oils are one of the alternatives, which can be used as fuel in diesel engines either in the form of straight vegetable oil or in the form of biodiesel. This study aims to present experimental data by utilization of home and industrial biodiesel as fuel in an agricultural tractor diesel engine. The home biodiesel production was made from different vegetable oils (crude rapeseed, edible sunflower and waste oil) with the process of one‐stage‐based catalyzed transesterification. A commercially available agricultural tractor ZETOR 7745 was employed. Measurements were taken on the power take‐off shaft by electrical dynamometer FROMENT XT200. According to the results, agricultural tractor diesel engine operating on home biodiesel fuels had better performance characteristics related to industrially produced biodiesel and similar to conventional diesel fuel. Copyright © 2009 John Wiley & Sons, Ltd.     

Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine

Vegetable oils and their methyl/ethyl esters are alternative renewable fuels for compression ignition engines. Different kinds of vegetable oils and their methyl/ethyl esters have been tested in diesel engines. However, tobacco seed oil and tobacco seed oil methyl ester have not been tested in diesel engines, yet. Tobacco seed oil is a non-edible vegetable oil and a by-product of tobacco leaves production. To the author's best knowledge, this is the first study on tobacco seed oil methyl ester as a fuel in diesel engines.In this study, potential tobacco seed production throughout the world, the oil extraction process from tobacco seed and the transesterification process for biodiesel production were examined. The produced tobacco seed oil methyl ester was characterized by exposing its major properties. The effects of tobacco seed oil methyl ester addition to diesel No. 2 on the performance and emissions of a four cycle, four cylinder turbocharged indirect injection (IDI) diesel engine were examined at both full and partial loads. Experimental results showed that tobacco seed oil methyl ester can be partially substituted for the diesel fuel at most operating conditions in terms of performance parameters and emissions without any engine modification and preheating of the blends.     

Experimental investigations of a four-stroke single cylinder direct injection diesel engine operated on dual fuel mode with producer gas as inducted fuel and Honge oil and its methyl ester (HOME) as injected fuels

In order to meet the energy requirements, there has been growing interest in alternative fuels like biodiesels, methyl alcohol, ethyl alcohol, biogas, hydrogen and producer gas to provide a suitable diesel oil substitute for internal combustion engines. Vegetable oils present a very promising alternative to diesel oil since they are renewable and have similar properties. Vegetable oils offer almost the same power output with slightly lower thermal efficiency when used in diesel engine [Srivastava A, Prasad R. Triglycerides-based diesel fuels. Renew Sustain Energy Rev 2000;4:111–33. [1]; Vellguth G. Performance of vegetable oils and their monoesters as fuels for diesel engines. SAE 831358, 1983. [2]; Demirbas A. Biodiesel production from vegetable oils via catalytic and non-catalytic supercritical methanol transesterification methods. Int J Prog Energy Combust Sci 2005;31:466–87. [3]; Jajoo BN, Keoti RS. Evaluation of vegetable oils as supplementary fuels for diesel engines. In: Proceedings of the XV national conference on IC engines and combustion, Anna University Chennai, 1997. [4]; Altin R, Cetinkaya S, Yucesu HS. The potential of using vegetable oil fuels as fuel for diesel engines. Int J Energy Convers Manage 2000;42:529–38, 248. [5]; Gajendra Babu MK, Chandan Kumar Das LM. Experimental investigations on a Karanja oil methyl ester fuelled DI diesel engine. SAE 2006-01-0238, 2006. [6]; Agarwal D, Kumar Agarwal A. Performance and emission characteristics of a Jatropha oil (preheated and blends) in a direct injection compression ignition engine. Int J Appl Therm Eng 2007;27:2314–23. [7]]. Research in this direction with edible oils have yielded encouraging results, but their use as fuel for diesel engine has limited applications due to higher domestic requirement [Scholl Kyle W, Sorenson Spencer C. Combustion Analysis of soyabean oil methyl ester in a direct injection diesel engine. SAE 930934, 1993. [8]; Nwafor OMI. Effect of advanced injection timing on the performance of rapeseed oil in diesel engines. Int J Renew Energy 2000;21:433–44. [9]; Nwafor OMI. The effect of elevated fuel inlet temperature on performance of diesel engine running on neat vegetable oil at constant speed conditions. Renew Energy 2003;28:171–81. [10]]. In view of this, Honge oil (Pongamia Pinnata Linn) being non-edible oil could be regarded as an alternative fuel for CI engine applications. The viscosity of Honge oil is reduced by transesterification process to obtain Honge oil methyl ester (HOME).Gasification is a process in which solid biomass is converted into a mixture of combustible gases, which complete their combustion in an IC engine. Hence, producer gas can act as a promising alternative fuel, especially for diesel engines by substituting considerable amount of diesel fuels. Downdraft moving bed gasifiers coupled with IC engine are a good choice for moderate quantities of available biomass, up to 500 kW of electric power. Hence, bioderived gas and vegetable liquids appear more attractive in view of their friendly environmental nature. Since vegetable oils produce higher smoke emissions, dual fuel operation could be adopted for improving their performance.     

Hydroprocessed vegetable oil as a fuel for transportation sector: A review

Renewable fuels produced from vegetable oils are an attractive alternative to fossil-based fuel. Different type of fuels can be derived from these triglycerides. One of them is biodiesel which is a mono alkyl ester of the vegetable oil. The biodiesel is produced by transesterification of the oil with an alcohol in the presence of a catalyst. Another kind of fuel (which is similar to petroleum-derived diesel) can be produced from the vegetable oil using hydroprocessing technique. This method uses elevated temperature and pressure along with a catalyst to produce a fuel termed as ‘renewable diesel’. The fuel produced has properties that are beneficial for the engine as well as the environment. It has high cetane number, low density, excellent cold flow properties and same materials can be used as are used for engine running on petrodiesel. It can effectively reduce NOx, PM, HC, CO emissions and unregulated emissions as well as greenhouse gases as compared to diesel. The fuel is also beneficial for the after-treatment systems. Trials in the field have shown that the volumetric fuel consumption of renewable diesel is higher than petrodiesel and nearly proportional to the volumetric heating value. The present review focuses on the hydroprocessing technique used for the renewable diesel production and the effect of different parameters such as catalyst, reaction temperature, hydrogen pressure, liquid hourly space velocity (LHSV) and H₂/oil ratio on oil conversion, diesel selectivity, and isomerization. The review also summarizes the effect; renewable diesel has on combustion, performance, and emission characteristics of a compression ignition engine.     

Performance evaluation of a diesel engine fueled with methyl ester of castor seed oil

In this investigation, castor methyl ester (CME) was prepared by transesterification using potassium hydroxide (KOH) as catalyst and was used in four stroke, single cylinder variable compression ratio type diesel engine. Tests were carried out at a rated speed of 1500 rpm at different loads. Straight vegetable oils pose operational and durability problems when subjected to long term usages in diesel engines. These problems are attributed to high viscosity, low volatility and polyunsaturated character of vegetable oils. The process of transesterification is found to be an effective method of reducing vegetable oil viscosity and eliminating operational and durability problems. The important properties of methyl ester of castor seed oil are compared with diesel fuel. The engine performance was analysed with different blends of biodiesel and was compared with mineral diesel. It was concluded that the lower blends of biodiesel increased the break thermal efficiency and reduced the fuel consumption. The exhaust gas temperature increased with increasing biodiesel concentration. The results proved that the use of biodiesel (produced from castor seed oil) in compression ignition engine is a viable alternative to diesel.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Bio-diesel as an alternative fuel for diesel engines—A review

The present review aims to study the prospects and opportunities of introducing vegetable oils and their derivatives as fuel in diesel engines. In our country the ratio of diesel to gasoline fuel is 7:1, depicting a highly skewed situation. Thus, it is necessary to replace fossil diesel fuel by alternative fuels. Vegetable oils present a very promising scenario of functioning as alternative fuels to fossil diesel fuel. The properties of these oils can be compared favorably with the characteristics required for internal combustion engine fuels. Fuel-related properties are reviewed and compared with those of conventional diesel fuel. Peak pressure development, heat release rate analysis, and vibration analysis of the engine are discussed in relation with the use of bio-diesel and conventional diesel fuel. Optimization of alkali-catalyzed transesterification of Pungamia pinnata oil for the production of bio-diesel is discussed. Use of bio-diesel in a conventional diesel engine results in substantial reduction in unburned hydrocarbon (UBHC), carbon monoxide (CO), particulate matters (PM) emission and oxide of nitrogen. The suitability of injection timing for diesel engine operation with vegetable oils and its blends, environmental considerations are discussed. Teardown analysis of bio-diesel B20-operated vehicle are also discussed.     

An investigation of using biodiesel/marine diesel blends on the performance of a stationary diesel engine

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high-energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. With the exception of rape seed oil which is the principal raw material for biodiesel fatty acid methyl esters, sunflower oil, corn oil and olive oil, which are abundant in Southern Europe, along with some wastes, such as used frying oils, appear to be attractive candidates for biodiesel production. In this paper, fuel consumption and exhaust emissions measurements from a single cylinder, stationary diesel engine are described. The engine was fueled with pure marine diesel fuel and blends containing two types of biodiesel, at proportions up to 50%. The two types of biodiesel appeared to have equal performance, and irrespective of the raw material used for their production, their addition to the marine diesel fuel improved the particulate matter, unburned hydrocarbons, nitrogen oxide and carbon monoxide emissions.     

Impact of Carbon Nanotubes and Di-Ethyl Ether as additives with biodiesel emulsion fuels in a diesel engine – An experimental investigation

In the current global energy scenario, fossil fuels face challenges with regards to exorbitant demand, environmental hazards and escalating costs. In this regard, the technical community is in quest for alternative resources. In this context, biodiesel fuel is potentially considered as alternative fuels for compression ignition engines. Hence, in this current investigation, biodiesel and biodiesel emulsions are prepared from a vegetable oil and further subjected for the blending with potential additives such as CNT (Carbon Nanotubes) and DEE (Di-Ethyl Ether) to improve the working attributes of the diesel engine. The entire investigation was carried out in five stages. In the first stage, both pure diesel and biodiesel (derived from jatropha oil) fuels were tested in the diesel engine to obtain baseline readings. In the second stage, water–biodiesel emulsion fuel was prepared in the proportion of 91% of biodiesel, 5% of water and 4% of emulsifiers (by volume). In the third stage, 50 ppm of CNT, 50 ml of DEE and combined mixture of CNT+DEE (50 ppm CNT+50 ml DEE) were mixed with the water–biodiesel emulsion fuel separately to prepare the CNT and DEE blended water–biodiesel emulsion fuels respectively. In fourth stage, the prepared emulsion fuels were subjected to stability investigations. In the fifth stage, all the prepared stable emulsion fuels were subjected for experimental testing in a diesel engine. It was observed that the CNT and DEE blended biodiesel emulsion fuels reflected better performance, emission and combustion attributes than that of pure diesel and biodiesel. At the full load, the brake thermal efficiency, NO and smoke emission of CNT+DEE fuels was 28.8%, 895 ppm and 36%, whereas it was 25.2%, 1340 ppm and 71% for pure diesel respectively. It was also observed that on adding CNT and DEE with the biodiesel emulsion fuels, the ignition delay was shortened and henceforth, the additive blended biodiesel emulsion fuels exhibited higher brake thermal efficiency and reduced emissions (NO, smoke) than that of pure diesel and biodiesel.     

Performance and emissions characteristics of Jatropha oil (preheated and blends) in a direct injection compression ignition engine

The scarce and rapidly depleting conventional petroleum resources have promoted research for alternative fuels for internal combustion engines. Among various possible options, fuels derived from triglycerides (vegetable oils/animal fats) present promising “greener” substitutes for fossil fuels. Vegetable oils, due to their agricultural origin, are able to reduce net CO₂ emissions to the atmosphere along with import substitution of petroleum products. However, several operational and durability problems of using straight vegetable oils in diesel engines reported in the literature, which are because of their higher viscosity and low volatility compared to mineral diesel fuel.In the present research, experiments were designed to study the effect of reducing Jatropha oil’s viscosity by increasing the fuel temperature (using waste heat of the exhaust gases) and thereby eliminating its effect on combustion and emission characteristics of the engine. Experiments were also conducted using various blends of Jatropha oil with mineral diesel to study the effect of reduced blend viscosity on emissions and performance of diesel engine. A single cylinder, four stroke, constant speed, water cooled, direct injection diesel engine typically used in agricultural sector was used for the experiments. The acquired data were analyzed for various parameters such as thermal efficiency, brake specific fuel consumption (BSFC), smoke opacity, CO₂, CO and HC emissions. While operating the engine on Jatropha oil (preheated and blends), performance and emission parameters were found to be very close to mineral diesel for lower blend concentrations. However, for higher blend concentrations, performance and emissions were observed to be marginally inferior.     

Characterization and effect of using rubber seed oil as fuel in the compression ignition engines

Vegetable oils pose some problems when subjected to prolonged usage in compression ignition engines because of their high viscosity and low volatility. The common problems are poor atomization, carbon deposits, ring sticking, fuel pump failure, etc. Converting the high viscosity vegetable oil into its blends or esters can minimize these problems. The various blends of rubber seed oil and diesel were prepared and its important properties such as viscosity, calorific value, flash point, fire point, etc. were evaluated and compared with that of diesel. The blends were then subjected to engine performance and emission tests and compared with that for diesel. It was found that 50–80% of rubber seed oil blends gave the best performance. Long run tests were conducted using optimized blend and diesel. It was found that blend fueled engine has higher carbon deposits inside combustion chamber than diesel-fueled engine. Utilization of blends requires frequent cleaning of fuel filter, pump and the combustion chamber. Hence, it is recommended that rubber seed oil–diesel blend fuel is more suitable for rural power generation.     

Progress in biodiesel processing

Biodiesel is a notable alternative to the widely used petroleum-derived diesel fuel since it can be generated by domestic natural sources such as soybeans, rapeseeds, coconuts, and even recycled cooking oil, and thus reduces dependence on diminishing petroleum fuel from foreign sources. The injection and atomization characteristics of the vegetable oils are significantly different than those of petroleum-derived diesel fuels, mainly as the result of their high viscosities. Modern diesel engines have fuel-injection system that is sensitive to viscosity change. One way to avoid these problems is to reduce fuel viscosity of vegetable oil in order to improve its performance. The conversion of vegetable oils into biodiesel is an effective way to overcome all the problems associated with the vegetable oils. Dilution, micro-emulsification, pyrolysis, and transesterification are the four techniques applied to solve the problems encountered with the high fuel viscosity. Transesterification is the most common method and leads to monoalkyl esters of vegetable oils and fats, now called biodiesel when used for fuel purposes. The methyl ester produced by transesterification of vegetable oil has a high cetane number, low viscosity and improved heating value compared to those of pure vegetable oil which results in shorter ignition delay and longer combustion duration and hence low particulate emissions.     

Performance characteristics of a low heat rejection diesel engine operating with biodiesel

Vegetable oils are a promising alternative among the different diesel fuel alternatives. However, the high viscosity, poor volatility and cold flow characteristics of vegetable oils can cause some problems such as injector coking, severe engine deposits, filter gumming, piston ring sticking and thickening of lubrication oil from long-term use in diesel engines. These problems can be eliminated or minimized by transesterification of the vegetable oils to form monoesters. These monoesters are known as biodiesel. The important advantages of biodiesel are lower exhaust gas emissions and its biodegradability and renewability compared with petroleum-based diesel fuel. Although the transesterification improves the fuel properties of vegetable oil, the viscosity and volatility of biodiesel are still worse than that of petroleum diesel fuel. The energy of the biodiesel can be released more efficiently with the concept of low heat rejection (LHR) engine. The aim of this study is to apply LHR engine for improving engine performance when biodiesel is used as an alternative fuel. For this purpose, a turbocharged direct injection (DI) diesel engine was converted to a LHR engine and the effects of biodiesel (produced from sunflower oil) usage in the LHR engine on its performance characteristics have been investigated experimentally. The results showed that specific fuel consumption and the brake thermal efficiency were improved and exhaust gas temperature before the turbine inlet was increased for both fuels in the LHR engine.     

Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters

The high viscosity of fish oil leads to problem in pumping and spray characteristics. The inefficient mixing of fish oil with air leads to incomplete combustion. The best way to use fish oil as fuel in compression ignition (CI) engines is to convert it into biodiesel. It can be used in CI engines with very little or no engine modifications. This is because it has properties similar to mineral diesel. Combustion tests for methyl ester of fish oil and its blends with diesel fuel were performed in a kirloskar H394 DI diesel engine, to evaluate fish biodiesel as an alternative fuel for diesel engine, at constant speed of 1500 rpm under variable load conditions. The tests showed no major deviations in diesel engine's combustion as well as no significant changes in the engine performance and reduction of main noxious emissions with the exception on NO_x. Overall fish biodiesel showed good combustion properties and environmental benefits.     

Experimental investigations on combustion, performance and emissions characteristics of neat karanji biodiesel and its methanol blend in a diesel engine

The increased focus on alternative fuels research in the recent years are mainly driven by escalating crude oil prices, stringent emission norms and the concern on clean environment. The processed form of vegetable oil (biodiesel) has emerged as a potential substitute for diesel fuel on account of its renewable source and lesser emissions. The experimental work reported here has been carried out on a turbocharged, direct injection, multi-cylinder truck diesel engine fitted with mechanical distributor type fuel injection pump using biodiesel-methanol blend and neat karanji oil derived biodiesel under constant speed and varying load conditions without altering injection timings. The results of the experimental investigation indicate that the ignition delay for biodiesel-methanol blend is slightly higher as compared to neat biodiesel and the maximum increase is limited to 1 deg. CA. The maximum rate of pressure rise follow a trend of the ignition delay variations at these operating conditions. However, the peak cylinder pressure and peak energy release rate decreases for biodiesel-methanol blend. In general, a delayed start of combustion and lower combustion duration are observed for biodiesel-methanol blend compared to neat biodiesel fuel. A maximum thermal efficiency increase of 4.2% due to 10% methanol addition in the biodiesel is seen at 80% load and 16.67 s⁻¹ engine speed. The unburnt hydrocarbon and carbon monoxide emissions are slightly higher for the methanol blend compared to neat biodiesel at low load conditions whereas at higher load conditions unburnt hydrocarbon emissions are comparable for the two fuels and carbon monoxide emissions decrease significantly for the methanol blend. A significant reduction in nitric oxide and smoke emissions are observed with the biodiesel-methanol blend investigated.