Direct microwave sintering of yttria-stabilized zirconia at 2·45 GHz

The feasibility of using direct MW heating—with 2·45 GHz radiation distributed in multimode applicators—for the obtainment of uncracked fully dense zirconia ceramics was studied. It was found that such a sintering approach can be used in the case of ZrO₂(Y₂O₃) powder compacts. Suitable correlation between target load mass, heating chamber architecture and forward power profile is the key to direct MW heating without thermal runaway. Sintered bulk densities close to the theoretical were obtained after firing cycles of about 2 h. Sintering rate enhancement in the MW furnace resulted in a reduction of ∼100°C in the minimal temperature required for full densification. Mechanical properties of MW and conventionally sintered specimens (fully dense state) were not significantly different. ©     

Sintering of PZT powders in MW furnace at 2·45 GHz

The feasibility of sintering PZT powder compacts—by direct MW heating, in multimode applicators at 2·45 GHz—was examined. Continuous heating from 20°C to sintering temperatures proved possible. Full sintering was achieved after heating cycles of about 1 h. PbO loss and electromagnetic fields intensity non-uniform spatial distribution are the main factors with negative influence on sintering. Cracking-warpage propensity is a strong function of specimens shape, size and the heating chamber set up. Dielectric and piezoelectric properties of MW and conventionally sintered specimens are similar.     

Hydrothermal synthesis,crystal structure and physical properties of {[Gd(H2O)4(μ2-C6NO2H5)2Gd(H2O)4](μ3-C6NO2H4)2(ZnCl3)2} · 2H2O · 2Cl

A bimetallic 4f–3d tetranuclear complex {[Gd(H₂O)₄(μ₂-C₆NO₂H₅)₂Gd(H₂O)₄](μ₃-C₆NO₂H₄)₂(ZnCl₃)₂} · 2H₂O · 2Cl (1) has been synthesized via hydrothermal reaction and structurally characterized by single-crystal X-ray diffraction. Complex 1 is characterized by a tetranuclear Gd₂Zn₂ structure with the gadolinium and zinc atoms interconnected by isonicotinic acid ligands. The tetranuclear species of {[Gd(H₂O)₄(μ₂-C₆NO₂H₅)₂Gd(H₂O)₄](μ₃-C₆NO₂H₄)₂(ZnCl₃)₂} link to isolated chlorine ions and water molecules via π?π interactions and hydrogen bonds to yield a 3-D supramolecular framework. Photoluminescent investigation reveals that the title complex displays an emission in ultraviolet region. The solid-state diffuse reflectance spectra of 1 reveal the presence of a sharp optical gap of 3.66 eV.     

A novel uranyl complex UO2(tci)(C3H5N2) · H2O: Synthesis,crystal structure and characterization

Reaction of uranium oxynitrate hexahydrate with tris(2-carboxyethyl)isocyanurate (tciH₃) in acidic aqueous solution (pH ～4–5) yields the compound UO₂(tci)(C₃H₅N₂) · H₂O. X-ray diffraction shows that the uranyl ion is in a hexagonal bipyramid structure. Uranium ion in the complex is found to be ligated with three chelating COO^? groups at the equatorial plane, two oxygen atoms linking to uranium atom formed the vertical axis. The complex has the layered topology structure in the space. The thermal analysis verifies the component and the structure of the complex.     

Heterogeneous oxidation of 2-octanol on 5 wt%Pt–1 wt%Bi/Carbon catalyst

The low activity of 5%Pt–1%Bi/Carbon for the oxidation of 2-octanol at atmospheric pressure and 343 K was investigated. Using solvents such as heptane and p-xylene, it was shown that the reaction rates decrease dramatically shortly after the start of the reaction due to poisoning by product adsorption. Hence this work investigates the effect of using different solvent mixtures on the oxidation reaction of 2-octanol with 5%Pt–1%Bi/Carbon. Mixtures with different volumetric ratios of heptane and dioxane were investigated to find the best composition capable of effectively removing the adsorbed amphiphilic ketone. It is apparent that the reaction rate is correlated with the adsorption coefficient of ketone on the catalyst, such that the maximum reaction rate occurs at the lowest ketone adsorption coefficient, corresponding to a concentration of 16–18%v/v dioxane. A model based on a Langmuir–Hinshelwood mechanism has been successfully fitted to the experimental rates.     

Phase evolution and chemical durability of Zr1-xNd xO2-x/2 (0 ≤ x ≤ 1) ceramics

A series of Zr_1-xNd _xO_2-x/2 (0 ≤ x ≤ 1) ceramics was prepared by solid-state reaction method. The effects of Nd content on the phase evolution were investigated. The chemical durability of resulting waste forms was also examined. The results show that the ceramics with x < 0.1 show monoclinic and cubic zirconia phase, with 0.2 ≤ x < 0.4 exhibit a single cubic phase, with 0.4 ≤ x ≤ 0.6 exhibit a single pyrochlore phase, with 0.6 < x < 0.8 exhibit a single cubic phase and remain cubic phases and hexagonal Nd₂O₃ when 0.8 ≤ x ≤ 1. The unit cell parameters of the Nd-doped zirconia samples increase as the Nd content increases. Moreover, the normalized element release rates of Nd element in Nd-doped zirconia ceramics firstly decrease with leaching time and almost no change after 21 days (∼0⁻⁶ g m⁻² d⁻¹), demonstrating its good chemical durability.     

Synthesis,structure of a coordination polymer: {Na2[Zn(C2O4)1.5H2PO4] · 2H2O}n

A phosphatooxalate compound {Na₂[Zn(C₂O₄)_1.5H₂PO₄] · 2H₂O}_n 1 was synthesized under hydrothermal condition and characterized by single-crystal X-ray diffraction, IR spectroscopy, thermal gravimetric analysis (TGA) and fluorescent spectroscopy. X-ray single-crystal analysis revealed that its structure was a new mixed inorganic–organic ligand supramolecular framework building up through multilayer assembly.     

Synthesis and negative thermal expansion properties of solid solutions Yb2−xLaxW3O12 (0 ≤ x ≤ 2)

A new series of rare earth solid solutions Yb_2?xLa_xW₃O₁₂ were successfully synthesized by the solid-state method. Effects of substituted ion lanthanum on the microstructures and thermal expansion properties in the resulting Yb_2?xLa_xW₃O₁₂ ceramics were investigated by X-ray diffraction (XRD), thermogravimetric analyzer (TGA), field emission scanning electron microscope (FESEM) and thermal mechanical analyzer (TMA). Results indicate that the structural phase transition of the Yb_2?xLa_xW₃O₁₂ changes from orthorhombic to monoclinic with increasing substituted content of lanthanum. The pure phases can form in the composition range of 0 ≤ x < 0.5 with orthorhombic structure and 1.5 < x ≤ 2 with monoclinic one. High lanthanum content leads to a low hygroscopicity of Yb_2?xLa_xW₃O₁₂. Negative thermal coefficients of the Yb_2?xLa_xW₃O₁₂ (0 ≤ x ≤ 2) also vary from ?7.78 × 10^?6 K^?1 to 2.06 × 10^?6 K^?1 with increasing substituted content of lanthanum.     

Uncoordinated inorganic salt in 1D chain structure: formation of a novel supermolecule [HgBr2(ptz)]2 · HgBr2 (ptz=phenothiazine)

A novel supermolecule [HgBr₂(ptz)]₂ · HgBr₂ (ptz=phenothiazine) with uncoordinated inorganic salt HgBr₂ presented in a 1D chain was prepared. The bulky ligand phenothiazine has unusual coordination mode with large steric inhibition perpendicular to the chain direction. The uncoordinated HgBr₂ molecule was stabilized by multiple weak Hg⋯Br interactions and the whole structure was also stabilized by strong π–π interactions and N–H⋯Br hydrogen bonds to form 2D network.     

Thermal expansion and thermal conductivity of SmxZr1−xO2−x/2 (0.1 ≤ x ≤ 0.5) ceramics

A study was conducted of the effect of additions of samarium oxide on the thermal expansion and thermal conductivity of zirconium oxide for thermal barrier coatings. Sm_xZr_1?xO_2?x/2 (0.1 ≤ x ≤ 0.5) ceramic powders synthesized with a chemical-coprecipitation and calcination method were sintered at 1873 K for 15 h. Structures of the synthesized powders and sintered ceramics were identified by X-ray diffractometer. The morphologies of ceramic powders were observed by transmission electron microscope. The thermal expansion coefficients and thermal diffusion coefficients of Sm_xZr_1?xO_2?x/2 ceramics were studied with a high-temperature dilatometer and a laser flash diffusivity technique from room temperature to 1673 K. The thermal conductivity was calculated from thermal diffusivity, density and specific heat of bulk ceramics. Sm_0.1Zr_0.9O_1.95 ceramics consists of both monoclinic and tetragonal structures. However, Sm_0.2Zr_0.8O_1.9 and Sm_0.3Zr_0.7O_1.85 ceramics only exhibit a defect fluorite structure. Sm_0.4Zr_0.6O_1.8 and Sm_0.5Zr_0.5O_1.75 ceramics have a pyrochlore-type lattice. With the increase of Sm₂O₃ content, the linear thermal expansion of Sm_xZr_1?xO_2?x/2 ceramics increases except for Sm_0.1Zr_0.9O_1.95. The thermal conductivities of Sm_xZr_1?xO_2?x/2 ceramics ranged from 1.41 at 873 K to 1.86 W m^?1 K^?1 at room temperature in a test temperature range of room temperature to 1673 K, and the results can be explained by phonon scattering mechanism.     

Mesoporous CuO/TixZr1 − xO2 catalysts for low-temperature CO oxidation

Mesoporous CuO/Ti_xZr_1 − xO₂ catalysts were prepared by a surfactant-assisted method, and characterized by N₂ adsorption/desorption, TEM, XPS, in-situ FTIR and H₂-TPR. The catalysts exhibited high specific surface area (S_BET = 241 m²/g) and uniform pore size distribution. XPS and in-situ FTIR displayed that Cu⁺ and Cu²⁺ species coexisted in the catalysts. The CuO/Ti_xZr_1 − xO₂ catalysts presented obviously higher activity in CO oxidation reaction than the CuO/TiO₂ and CuO/ZrO₂ catalysts. Effect of molar ratios of Ti to Zr and calcination temperature on catalytic activity was investigated. The CuO/Ti_0.6Zr_0.4O₂ catalyst calcined at 400 °C exhibited excellent activity with 100% CO conversion at 140 °C.     

A Michael-type reaction between acrylato ions and ethylenediamine coordinated to Ni(II). Synthesis,crystal structure and magnetic properties of [Ni2(EDDP)2(H2O)2] · 2H2O (H2EDDP = ethylenediamine-N,N-dipropionic acid)

The reaction between NiCO₃ · Ni(OH)₂, acrylic acid and ethylenediamine in a 2:4:1 molar ratio affords the binuclear complex, [Ni₂(EDDP)₂(H₂O)₂] · 2H₂O 1. The organic ligand, EDDP^2? (the dianion of the ethylenediamine-N,N-dipropionic acid ligand), results from the addition of one amine group to the carbon–carbon double bonds of two acrylato ions. The crystal structure of 1 consists of neutral centrosymmetric entities, with the nickel ions connected by two carboxylato groups, each one acting as a monoatomic bridge. The intramolecular Ni?Ni distance is 3.212 Å. The metal ions exhibit an octahedral geometry. The cryomagnetic investigation of 1 reveals an antiferromagnetic coupling of the nickel(II) ions (J = ?21.8 cm^?1, H = ?JS_Ni1S_Ni2).     

Heteroepitaxial ZnO/sapphire (0 0 0 1) structure prepared by sol–gel process

ZnO thin films were grown on sapphire (0 0 0 1) substrates by sol–gel process and their structural and optical properties were characterized in detail. High-quality texture was obtained by using precursor solution of zinc acetate and ethanolamine in 2-methoxyethanol, pyrolyzed at 300 °C, then heated at 500 °C, and finally annealed at 750 °C. Highly c-axis oriented ZnO films were confirmed by X-ray θ–2θ scan. A relatively high transmittance in the visible spectra range and clear absorption edge of the film were observed. Epitaxial relationship between ZnO and sapphire and photoluminescence of the film were examined by using a X-ray pole-figure analysis and He–Cd laser. Near-band-edge emission with a deep-level emission was observed.     

Effect of steam on the acid strength of H3PW12O40/SiO2 · nH2O and its application in skeletal isomerization of n-butane

The effect of steam on the acid strength of H₃PW₁₂O₄₀ (HPW)/SiO₂ · nH₂O was determined by the Hammett indicators. When the steam content in N₂ was 1.6%, the acidity (H₀ > −13.7) of HPW/SiO₂ · nH₂O could be kept for over 10 h at 300 °C, but for only 2 h when steam was lacking. When it was used as a catalyst for skeletal isomerization of n-butane to isobutane at 300 °C, the HPW/SiO₂ · nH₂O showed stability in the presence of steam (1.6% in feed) better than that without steam, due to a suppression of the loss of crystalline water.     

Crystal structure,mixture behavior,and microwave dielectric properties of novel temperature stable (1 − x)MgMoO4 − xTiO2 composite ceramics

Novel temperature stable MgMoO₄–TiO₂ microwave dielectric ceramics were prepared by a solid state reaction process at low temperature (950 °C). As TiO₂ content increases, the relative permittivity increases while the Q × f value decreases, and the variation mechanisms are proposed, respectively. The temperature coefficient of resonant frequency (τ_f) shifts to the positive direction as TiO₂ is added. The mixture mechanisms of τ_f value for two-phase composite materials are supposed. A near-zero τ_f value (3.2 ppm/°C) is obtained when x = 0.3, with ε_r = 9.13 ± 0.03 and Q × f = 11,990 GHz. The 0.7MgMoO₄–0.3TiO₂ composites are considered to be appropriate as a low temperature co-fired ceramic material for microwave wireless communication applications.     

Unprecedented cadmium(II) complex with (44 · 66) net topology and in situ ligand synthesis

Hydrothermal reactions of 4,4′-bipyridine-2,2′-dicarboxylic acid (H₂BPDCA) with Cu(II) and Cd(II) nitrate salts result in the formation of two complexes [Cu(2,4-Hpydca)₂(H₂O)₂] (1) and [Cd(2,4-pydca)]_n (2) with pyridine-2,4-dicarboxylate (2,4-pydca²⁻), rather than BPDCA²⁻, as ligand, namely the in situ transformation of H₂BPDCA to H₂pydca occurred under the hydrothermal conditions. Complex 1 has been previously reported from different synthetic route, however, complex 2 is the first binodal 5-connecting 3D framework with unprecedented (4⁴ · 6⁶) net topology. The results provide a new strategy for in situ ligand synthesis and construction of coordination polymers with specific topology.     

Divalent metal complexes of formylhydrazine: Syntheses and crystal structures of M(CH4N2O)2(H2O)2·2NO3 (M = Zn,Co)

The syntheses and crystal structures of Zn(CH₄N₂O)₂(H₂O)₂·2(NO₃) (1) and Co(CH₄N₂O)₂(H₂O)₂·2(NO₃) (2), the first well-characterised metal complexes of formylhydrazine (fh), are described. In both compounds, the fh acts as an N,O-bidentate ligand in a centrosymmetric [M(fh)₂(H₂O)₂]²⁺ cation, with charge balance supplied by nitrate counter ions. The packing for the two compounds are quite different: in 1, chains of [Zn(fh)₂(H₂O)₂]²⁺ units are seen in the triclinic unit cell, whereas in the monoclinic structure of 2, sheets of cations occur. This might arise because the conformations of the five-membered chelate rings for the ligands are slightly different, with that for 2 showing a greater degree of puckering.