The structural and kinetic characteristics of Mg1.9Al0.1Ni alloy synthesized by mechanical alloying

The structural and kinetic characteristics of the mechanically alloyed Mg_1.9Al_0.1Ni were investigated. It was found that Mg_1.9Al_0.1Ni can absorb/desorb about 3.55/3.44 mass% H at a high rate and it has a hexagonal crystal structure as Mg₂Ni. The hydriding/dehydriding (H/D) rates in the two-phase (–β) region of Mg_1.9Al_0.1Ni were measured and studied at temperatures ranging from 553 to 623 K under an approximately isobaric condition. The obtained data of H/D rates indicated that hydrogen diffusion was the rate-controlling step through the hydride phase. A new model was successfully used to calculate the kinetic experimental results. It can be seen that theoretical calculation agrees well with experimental data. The corresponding activation energies are 47 600 and 54 500 J/mol H₂ for H/D processes, respectively.     

Hydriding combustion synthesis of Mg–CaNi5 composites

The composites of Mg–x wt.% CaNi₅ (x = 20, 30 and 50) were prepared by hydriding combustion synthesis (HCS) and the phase evolution during HCS as well as the hydriding properties of the products were investigated. It was found that Mg reacted with CaNi₅ forming Mg₂Ni and Ca during the heating period of HCS. Afterwards, the resultant Mg₂Ni and Ca as well as the remnant Mg reacted with hydrogen during the cooling period. The lower platform in the P–C isotherms corresponds to the hydriding of Mg, and the higher one corresponds to Mg₂Ni. With the increase of the content of CaNi₅ from 20 to 50 wt.%, the hydrogen content of the HCS products increases at first and then decreases. The Mg–30 wt.% CaNi₅ composite has the maximum hydrogen capacity of 4.74 wt.%, and it can absorb 3.51 wt.% of hydrogen in the first hydriding process without activation.     

Synthesis and electrode characteristics of the new composite alloys Mg2Ni-xwt.% Ti2Ni

A new composite alloy Mg₂Ni-xwt.% Ti₂Ni has been successfully synthesised using a ‘particle inlaying’ method. Scanning electron microscopy and energy dispersive spectroscopy revealed that very fine Ti₂Ni particles were inlaid onto the surface of Mg₂Ni particles by mechanical treatment and sintering. XRD showed the composite alloys were composed of primary alloys Mg₂Ni, Ti₂Ni and new phases TiNi, Ti---Mg formed in the composite procedure. The electrode characteristics of Mg₂Ni-xwt.% Ti₂Ni alloys in an alkaline solution have been investigated and compared with those of Mg₂Ni. The discharge capacity of the alloy electrode was effectively improved from 8 mA h g¹ of Mg₂Ni to 165 mA h g¹ of Mg₂Ni-40wt.% Ti₂Ni at ambient temperature, which is almost comparable with that of Ti₂Ni electrode (170 mA h g¹). It is believed that the fine Ti₂Ni particles inlaid on the surface of Mg₂Ni particles play a two-fold role: firstly, they hydride-dehydride as hydrogen storage materials themselves: secondly, they provide active sites and pathways for Mg₂Ni hydriding-dehydriding. This is supported by analysis of discharge behaviour and electrochemical impedance spectra studies.     

Microstructural evolution during controlled ball milling of (Mg2Ni+MgNi2) intermetallic alloy

Nearly dual-phase Mg–Ni alloy fabricated by ingot metallurgy (IM) and comprising 30 vol% Mg₂Ni and 61 vol% MgNi₂ intermetallic compounds (remaining 9 vol% of unreacted Mg) was mechanically (ball) milled under controlled shearing for 10, 30, 70 and 100 h. The majority of the medium- and small-sized powder particles exhibited a relatively homogeneous microstructure of milled Mg₂Ni and MgNi₂. A fraction of large-sized particles developed the ‘core and mantel’ microstructure after milling for 70 and 100 h. The ‘core’ contains poorly milled MgNi₂ particles and the ‘mantel’ is a thoroughly milled mixture of Mg₂Ni, MgNi₂ and, possibly, residual Mg. X-ray diffraction provides evidence of nanostructurization and eventual amorphization of a fraction of a heavily ball milled Mg₂Ni phase. The remnant Mg₂Ni developed a nanocrystalline/submicrocrystalline structure. The co-existing MgNi₂ phase developed a submicrocrystalline structure within the powder particles. The results are rationalized in terms of enthalpy effects by the application of Miedema’s semi-empirical model to the phase changes in ball milled intermetallics.     

Effects of sintering on composite metal hydride alloy of Mg2Ni and TiNi synthesized by mechanical alloying

As-milled composite metal hydrides composed of Mg₂Ni and TiNi phases were cold-pressed under a pressure of 490 MPa and sintered for 1 h at 5×10⁻⁶ Torr and 300 °C. Electrochemical characteristics of the sintered composite metal hydride electrode were investigated. The maximum discharge capacity of the sintered composite alloy electrode was 125 mAh/g at a discharge current density of 100 mA/g. This value was similar to that of the as-milled one before sintering. However, the sintered electrode retained 80% of the maximum discharge capacity after 150 cycles, while the as-milled electrode retained only 55%. This is because after the sintering process an interface between Mg₂Ni and TiNi plays a role similar to a diffusion layer of hydrogen. In the sintered composite electrode, when a discharging step proceeds, hydrogen absorbed in a Mg₂Ni particle can move into a TiNi phase through the bonded-interface between Mg₂Ni and TiNi, then discharges at the interface between TiNi and the electrolyte. Also, the electrochemical impedance spectroscopy (EIS) tests showed that the composite alloy electrodes had a lower charge-transfer resistance and a higher hydrogen diffusion coefficient than those in single-phase Mg₂Ni. This indicates that TiNi particles in the composite are the active sites for redox reaction of hydrogen and the pathway for the diffusion of hydrogen     

Direct synthesis of MgCNi3 by mechanical alloying

MgCNi₃, an intermetallic compound with superconductivity, was synthesized from the Mg (or Mg₂Ni), Ni and graphite powders by mechanical alloying (MA). It is shown that the preliminary condition for the formation of MgCNi₃ is that Mg₂Ni must form in advance of MgCNi₃ in the MA process or be the starting component.     

Improved durability of hydrogen storage alloys

An effective and durable hydrogen storage module was required to fuel micro-power systems. Two primary specifications for the hydrogen fuel module in this application were a high volumic storage capacity and rapid hydrogen storage and release under atmospheric pressure or lower at room temperature. In addition, the hydrogen module should be operable for thousands of cycles with fast hydriding and dehydriding rates and be resistant to deactivation on exposure to air for many months and longer. In our prior work, mechanical grinding a small amount of palladium with the hydrogen storage alloys was shown to greatly improve the hydrogen storage performance. The palladium treatment of three intermetallic alloys, AB₅ type LaNi_4.7Al_0.3 and CaNi₅, and A₂B type Mg₂Ni, lowered the activation pressure to sub-atmospheric pressure at room temperature and also significantly increased the hydrogen absorption and desorption rates. This work focused on the durability of hydrogen absorption and desorption performances after exposure of the storage materials to air. The palladium treated hydrogen storage alloys retained both low activation pressures and fast absorption and desorption rates even after more than 2 years air exposure.     

Improvement in hydrogen sorption properties of Mg by reactive mechanical grinding with Cr2O3, Al2O3 and CeO2

We tried to improve the hydrogen sorption properties of Mg by mechanical grinding under H₂ (reactive mechanical grinding) with oxides Cr₂O₃, Al₂O₃ and CeO₂. The hydriding rates of Mg are reportedly controlled by the diffusion of hydrogen through a growing Mg hydride layer. The added oxides can help pulverization of Mg during mechanical grinding. A part of Mg is transformed into MgH₂ during reactive mechanical grinding. The Mg+10wt.%Cr₂O₃ powder has the largest transformed fraction 0.215, followed in order by Mg+10wt.%CeO₂ and Mg+10wt.%Al₂O₃. The Mg+10wt.%Cr₂O₃ powder has the largest hydriding rates at the first and fifth hydriding cycle, followed in order by Mg+10wt.%Al₂O₃ and Mg+10wt.%CeO₂. Mg+10wt.%Cr₂O₃ absorbs 5.87wt.% H at 573 K, 11 bar H₂ during 60 min at the first cycle. The Mg+10wt.%Cr₂O₃ powder has the largest dehydriding rates at the first and fifth dehydriding cycle, followed by Mg+10wt.%CeO₂ and Mg+10wt.%Al₂O₃. It desorbs 4.44 wt.% H at 573 K, 0.5 bar H₂ during 60 min at the first cycle. All the samples absorb and desorb less hydrogen at the fifth cycle than at the first cycle. It is considered that this results from the agglomeration of the particles during hydriding–dehydriding cycling. The average particle sizes of the as-milled and cycled powders increase in the order of Mg+10wt.%Cr₂O₃, Mg+10wt.%Al₂O₃ and Mg+10wt.%CeO₂. The quantities of hydrogen absorbed or desorbed for 1 h for the first and fifth cycles decrease in the order of Mg+10wt.%Cr₂O₃, Mg+10wt.%Al₂O₃ and Mg+10wt.%CeO₂. The quantities of absorbed or desorbed hydrogen increase as the average particle sizes decrease. As the particle size decreases, the diffusion distance shortens. This leads to the larger hydriding and dehydriding rates. The Cr₂O₃ in the Mg+10wt.%Cr₂O₃ powder is reduced after hydriding–dehydriding cycling. The much larger chemical affinity of Mg than Cr for oxygen leads to a reduction of Cr₂O₃ after cycling.     

Mechanically milled Mg composites for hydrogen storage the transition to a steady state composition

Magnesium alloys are potentially the best materials for gaseous hydrogen storage. However, their practical use is limited by poor hydrogen absorption and desorption kinetics. This problem can be resolved by mixing Mg alloys with other materials to form composites. We present an investigation of the initial hydriding characteristics, as well as the compositional transformation of composites made of La₂Mg₁₇ + LaNi₅ mechanically milled in a 2:1 weight ratio. Composites produced with varying durations and intensities of milling were tested. Those milled to the greatest extent proved to have the best initial hydrogen absorption and desorption kinetics. The kinetics of the most heavily milled composite were superior to those of La₂Mg₁₇. This composite absorbed 90% of its full hydrogen capacity (3.5 wt.% H₂) in less than 1 min at 250°C and desorbed the same quantity of hydrogen in 6 min. Under the same conditions pure La₂Mg₁₇ took 2.5 h to absorb and 3 h to desorb 90% of its full hydrogen capacity (4.9 wt.% H₂). Scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction were used to characterize the mechanically milled powders before and after hydriding. The unhydrided powders consisted of LaNi₅ grains surrounded by a fractured LaMg₁₇ matrix. Hydrogen cycling, at temperatures up to 350°C, induced phase changes, segregation, and disintegration of the composites. The resulting fine powder (less than 1 μm) consisted primarily of Mg, Mg₂Ni, and La phases.     

Influence of tin on the electrochemical and gas phase hydrogen sorption in Mg2−xSnxNi (x = 0, 0.1, 0.3)

Mg_2−xSn_xNi (x = 0, 0.1, 0.3) alloys were synthesized by reactive ball milling under protective Ar atmosphere and liquid n-heptane. The microstructure and the morphology of the powders were determined by X-ray diffraction and scanning electron microscopy. The as-milled alloys consist of Mg₂Ni nanocrystals with an average grain size in the range 3–7 nm, depending on the alloy composition. Sn containing phases were not detected even in the Sn-rich alloy. Obviously, Sn is dissolved in the Mg₂Ni intermetallic compound. Gas phase sorption of hydrogen was not observed in the alloys containing Sn (Mg_2−xSn_xNi; x = 0.1, 0.3). It was suggested that Sn impedes the process of hydrogen molecules decomposition. The as-milled alloys absorbed reversibly hydrogen electrochemically. Mg₂Ni alloy showed the highest discharge capacity of 300 mAh/g. The capacity of Mg_1.9Sn_0.1Ni and Mg_1.7Sn_0.3Ni was about 260 mAh/g. It was found that Sn improved the cycle life of the electrode.     

Hydrogen storage properties of Mg100−xNix (x = 5, 11.3, 20, 25) composites prepared by hydriding combustion synthesis followed by mechanical milling (HCS + MM)

We reported the structure and the notable hydrogen storage properties of the composites Mg_100−xNi_x (x = 5, 11.3, 20, 25) prepared from metallic powder mixtures of magnesium and nickel by the process of HCS + MM, i.e., the hydriding combustion synthesis (HCS) followed by mechanical milling (MM). X-ray diffraction (XRD) and scanning electron microscopy (SEM) results demonstrated that mechanical milling led to drastic pulverization and grain refinement of the composite produced by HCS. All the composites with different compositions showed a remarkable decline in dehydriding temperature comparing with that of the hydride mixtures prepared only by HCS. Furthermore, the hydriding rates of these composites were excellent. At 313 K the composite Mg₈₀Ni₂₀ showed the highest hydrogen capacity of 2.77 wt.% within 600 s among these four composites. The Mg₉₅Ni₅ showed maximum capacity of 4.88 wt.% at 373 K and 5.41 wt.% at 473 K within only 100 s. Some factors contributing to the improvement in hydriding rates were discussed in this paper.     

不同激光功率下镁合金表面激光熔覆Ni60合金涂层的显微组织和磨损性能

为提高镁合金表面的耐磨性,利用5kW横流连续CO2激光器在AZ31B镁合金表面熔覆Ni60合金粉末,制备了无裂纹、气孔等缺陷的熔覆层。分析讨论了不同激光功率下熔覆层的显微组织和磨损性能。结果表明:熔覆层的显微组织为典型的枝晶状态,且随着激光功率的增加,枝晶尺寸增加;不同的激光功率下,熔覆层都由Mg、MgNi2、Mg2Ni3Si、Mg2Ni、Mg2Si和FeNi组成,但当激光功率增加时,Mg相含量逐渐减小,其它相含量逐渐增多。在枝晶细化和各种金属间化合物的共同作用下,熔覆层的显微硬度和耐磨性能都得到提高,且激光功率P=3 000W时,提高程度最大,即显微硬度提高了840%～1 102%,磨损失量是原始AZ31B镁合金的8.57%。     

Phase Stability in Mechanically Alloyed Mg–Ni System Studied by Experiments and Thermodynamic Calculations

In this study, microstructural evolution of Mg–Ni alloy during mechanical alloying(MA) was investigated.Also, a thermodynamic approach was utilized to predict the most stable phases formed in Mg–Ni alloy after MA. The phase composition and microstructural properties of Mg–Ni alloy were assessed by X-ray diffractometry, high-resolution field emission scanning electron microscopy and high-resolution transmission electron microscopy. The results showed that ball milling of magnesium and nickel powder mixture for 70 h yields nanostructural Mg2Ni compound with an average grain size of ~20 nm. Thermodynamic calculations revealed that in the composition ranges of 0.0 \ XMg\ 0.03(at.%)and 0.97 \ XMg\ 1, there is no driving force for amorphous phase formation. In the composition range of 0.07 \ XMg\ 0.93, the change of Gibbs free energy for amorphous phase formation was more negative than solid solution.While for XMg= 0.66(nominal composition of Mg2Ni intermetallic phase), the change of Gibbs free energy for intermetallic phase was found to be more negative than both amorphous and solid solution phases indicating that Mg2Ni intermetallic compound is the most stable phase, in agreement with the experimental observations.     

Study of amorphous Ni–S(La) alloy used as HER cathode in alkaline medium

The hydriding combustion synthesis (HCS) of Mg₂FeH₆ and Mg₂Ni_1−xFe_x hydrides was systematically studied by changing the value of x from 0.25 to 1.0. This study aimed at improving the Mg₂FeH₆ yield in production and examining the effect of the addition of nickel to the hydrogen storage properties of the Mg₂FeH₆ hydride. In synthesizing metallic hydrides, the raw materials in metallic powders were mechanically activated by a ball mill before the HCS treatment. As a result, the ball-milled 2Mg + Fe recorded as much as 5 mass% in hydrogen storage capacity during the HCS treatment, and the final product successfully indicated a high purity Mg₂FeH₆. Interestingly, the deformation enthalpies of the Mg₂Ni_1−xFe_x hydrides were larger by 10% or more than Mg₂NiH₄ and Mg₂FeH₆, taken individually. This was collateral evidence to prove that the HCS of Mg₂FeH₆ and Mg₂Ni_1−xFe_x hydrides with ball milling (BM) produced a new structure of the Mg–Ni–Fe–H system due to the synergy effect.     

Microstructural modifications induced by hydrogen absorption in Mg5Ga2 and Mg6Pd

We have recently proposed a new method to design one-dimensional structures of MgH₂ in the nano- and micrometer ranges by hydrogen-induced disproportionation of bulk Mg₂₄Y₅. The present study confirms the same behavior in hydrogenated Mg₅Ga₂ and Mg₆Pd. Single-crystalline one-dimensional structures and microparticles of MgH₂ are formed by hydrogen absorption and subsequent partial disproportionation of Mg₅Ga₂ and Mg₆Pd. The MgH₂ whiskers and particles grow with different morphologies for different alloying partners. Growth mechanisms are proposed in relation to the morphology and the chemical surface composition of original compounds.     

TiNiNb钎焊Cf/SiC与TC4接头组织结构

文中在钎焊温度980℃、钎焊时间15 min的条件下,采用Ti_54.8Ni_34.4Nb_10.8（原子分数,%）共晶合金粉末真空钎焊C_f/SiC复合材料与TC4钛合金.用SEM,EDS及差热分析法（DTA）观察测定了钎料组织、成分及熔点,分析了钎焊接头的微观组织结构.结果表明,Ti_54.8Ni_34.4Nb_10.8共晶钎料由Ti₂Ni及Ti（Nb,Ni）化合物组成,实际熔点为935℃.钎焊过程中,Ti和Nb元素与复合材料反应形成TiC和NbC混合反应层;钎料中的镍与TC4中的镍发生互扩散,在TC4钛合金侧形成扩散层;连接层由弥散分布的Ti（Nb,Ni）化合物和Ti₂Ni相组成.C_f/SiC与连接层界面为接头最薄弱环节,此处易形成裂纹.     

Hydrogen absorption properties of the slurry system composed of liquid C6H6 and F-treated Mg2Ni

The hydrogenation characteristics of the slurry composed of the NH₄F solution treated Mg₂Ni and liquid C₆H₆ were studied. The F-treatment results in a net-shaped MgF₂ surface and higher nickel content in the sub-layer. It is found that the hydride of the NH₄F treated alloy has a much higher activity for the hydrogenation of benzene. The catalytic activity for hydrogenation of the alloy depended strongly on the surface properties of the catalyst. At 483 K and under a hydrogen pressure of 4.0 MPa, the alloy absorbed hydrogen first, transformed into hydride and then the benzene was hydrogenated to cyclohexane with the hydride as the catalyst. The hydrogen absorption capacity of slurry system composed of 20 wt.% treated alloy and benzene reached 6.4 wt.% and the hydrogenation completed in 20 min. Results of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) analysis on the crystal structure, surface composition and surface morphology of the untreated and treated alloy are presented and discussed.     

Disintegration and fine powder preparation of Nb75Si25 via hydrogenation

Hydrogenation of Nb₇₅Si₂₅ directly in an arc-melting chamber after arc-melting was investigated. A Nb₇₅Si₂₅ ingot absorbs hydrogen rapidly and simultaneously disintegrates into fine hydride powder. After dehydriding at 1073 K for 10.8 ks, fine Nb₇₅Si₂₅ particles with an irregular angular shape are obtained. The collecting efficiency of powder under 100 mesh is 56.1 wt.%.     

Crystal structures of VSn2, NbSn2 and CrSn2 with Mg2Cu-type structure and NbSnSb with CuAl2-type structure

Several binary stannides of the early transition metals T have been reported with the composition T₂Sn₃ previously. However, the present structure refinements from single-crystal X-ray data show that they have the compositions VSn₂, NbSn₂ and CrSn₂ (R = 0.028, R = 0.018 and R = 0.021 with 17 variable parameters and 828, 512 and 440 structure factors respectively). Their orthorhombic Mg₂Cu-type structure is closely related to the structures of MoSn₂ (Mg₂Ni type) and CuAl₂. The latter structure type was confirmed for NbSnSb by a structure refinement from single-crystal data (R = 0.010 for eight variables and 254 F values). Electrical conductivity measurements show CrSn₂ and MoSn₂ to be metallic conductors.