Hydriding combustion synthesis of Mg–CaNi5 composites

The composites of Mg–x wt.% CaNi₅ (x = 20, 30 and 50) were prepared by hydriding combustion synthesis (HCS) and the phase evolution during HCS as well as the hydriding properties of the products were investigated. It was found that Mg reacted with CaNi₅ forming Mg₂Ni and Ca during the heating period of HCS. Afterwards, the resultant Mg₂Ni and Ca as well as the remnant Mg reacted with hydrogen during the cooling period. The lower platform in the P–C isotherms corresponds to the hydriding of Mg, and the higher one corresponds to Mg₂Ni. With the increase of the content of CaNi₅ from 20 to 50 wt.%, the hydrogen content of the HCS products increases at first and then decreases. The Mg–30 wt.% CaNi₅ composite has the maximum hydrogen capacity of 4.74 wt.%, and it can absorb 3.51 wt.% of hydrogen in the first hydriding process without activation.     

Study of amorphous Ni–S(La) alloy used as HER cathode in alkaline medium

The hydriding combustion synthesis (HCS) of Mg₂FeH₆ and Mg₂Ni_1−xFe_x hydrides was systematically studied by changing the value of x from 0.25 to 1.0. This study aimed at improving the Mg₂FeH₆ yield in production and examining the effect of the addition of nickel to the hydrogen storage properties of the Mg₂FeH₆ hydride. In synthesizing metallic hydrides, the raw materials in metallic powders were mechanically activated by a ball mill before the HCS treatment. As a result, the ball-milled 2Mg + Fe recorded as much as 5 mass% in hydrogen storage capacity during the HCS treatment, and the final product successfully indicated a high purity Mg₂FeH₆. Interestingly, the deformation enthalpies of the Mg₂Ni_1−xFe_x hydrides were larger by 10% or more than Mg₂NiH₄ and Mg₂FeH₆, taken individually. This was collateral evidence to prove that the HCS of Mg₂FeH₆ and Mg₂Ni_1−xFe_x hydrides with ball milling (BM) produced a new structure of the Mg–Ni–Fe–H system due to the synergy effect.     

Influence of tin on the electrochemical and gas phase hydrogen sorption in Mg2−xSnxNi (x = 0, 0.1, 0.3)

Mg_2−xSn_xNi (x = 0, 0.1, 0.3) alloys were synthesized by reactive ball milling under protective Ar atmosphere and liquid n-heptane. The microstructure and the morphology of the powders were determined by X-ray diffraction and scanning electron microscopy. The as-milled alloys consist of Mg₂Ni nanocrystals with an average grain size in the range 3–7 nm, depending on the alloy composition. Sn containing phases were not detected even in the Sn-rich alloy. Obviously, Sn is dissolved in the Mg₂Ni intermetallic compound. Gas phase sorption of hydrogen was not observed in the alloys containing Sn (Mg_2−xSn_xNi; x = 0.1, 0.3). It was suggested that Sn impedes the process of hydrogen molecules decomposition. The as-milled alloys absorbed reversibly hydrogen electrochemically. Mg₂Ni alloy showed the highest discharge capacity of 300 mAh/g. The capacity of Mg_1.9Sn_0.1Ni and Mg_1.7Sn_0.3Ni was about 260 mAh/g. It was found that Sn improved the cycle life of the electrode.     

Hydrogen storage properties of MgH2/SWNT composite prepared by ball milling

A systematic investigation was performed on the hydrogen storage properties of mechano-chemically prepared MgH₂/single-walled carbon nanotube (SWNT) composites. It is found that the hydrogen absorption capacity and hydriding kinetics of the composites were dependent on the addition amount of SWNTs as well as milling time. A 5 wt.% addition of SWNTs is optimum to facilitate the hydrogen absorption and desorption of MgH₂. The composite MgH₂/5 wt.% SWNTs milled for 10 h can absorb 6.7 wt.% hydrogen within about 2 min at 573 K, and desorb 6 wt.% hydrogen in about 5 min at 623 K. Prolonging the milling time over 10 h leads to a serious degradation on hydrogen storage property of the MgH₂/SWNT composite, and property/structure investigations suggest that the property degradation comes from the structure destruction of the SWNTs.     

Electrochemical characteristics of Mg2−xZrxNi (x = 0–0.6) electrode alloys prepared by mechanical alloying

The electrode alloys Mg_2−xZr_xNi (x = 0, 0.15, 0.3, 0.45 and 0.6) were prepared by mechanical alloying (MA). Mg in the alloy was partially substituted with Zr in order to improve the electrochemical characteristics of the Mg₂Ni-type alloy. The microstructures and the electrochemical characteristics of the experimental alloys were measured systemically. The effects of substituting Mg with Zr and MA technique on the microstructures and electrochemical performances of the alloys were investigated in detail. The results obtained by XRD, SEM and TEM show that the substitution of Zr is favourable for the formation of an amorphous phase. For a fixed milling time, the amorphous phase in the alloy grows with increasing Zr content. The electrochemical measurement indicates that the substitution of Zr can dramatically enhance the discharge capacity with preferable cycle stability, and it markedly improves the discharge voltage characteristic of the alloys. For x ≤ 0.3, the discharge capacity of the alloys monotonically increases with milling time. But for x > 0.3, it has a maximum value with the change of milling time.     

The characteristics of Li(CoxNi1 − x)O2 cathode powders formed from the fine-sized Co3O4/NiO precursor powders

Li(Co_xNi_1 − x)O₂ (0 ≤ x ≤ 1) cathode powders were prepared by solid state reaction method using Co₃O₄/NiO precursor powders obtained by spray pyrolysis. The effect of the ratios of cobalt and nickel components on the characteristics of Co₃O₄/NiO precursor and Li(Co_xNi_1 − x)O₂ cathode powders were investigated. The Co₃O₄/NiO precursor powders with the ratios of cobalt and nickel components as 1/0, 0.75/0.25 and 0.5/0.5 had submicron size and regular morphologies. On the other hand, the Co₃O₄/NiO powders with the high contents of nickel component had aggregated morphologies of submicron size primary powders. The fine-sized precursor powders formed the fine-sized LiCoO₂ and Li(Co_0.75Ni_0.25)O₂ cathode powders by solid state reaction with LiOH powders. However, the high contents of the nickel component of the Co₃O₄/NiO precursor powders formed the Li(Co_xNi_1 − x)O₂ (0 ≤ x ≤ 0.5) cathode powders with aggregated morphologies and large sizes. The discharge capacities of the powders increased with increasing the nickel content into the Li(Co_xNi_1 − x)O₂ cathode powders up to 188 mAh/g.     

Mechanically milled Mg composites for hydrogen storage the transition to a steady state composition

Magnesium alloys are potentially the best materials for gaseous hydrogen storage. However, their practical use is limited by poor hydrogen absorption and desorption kinetics. This problem can be resolved by mixing Mg alloys with other materials to form composites. We present an investigation of the initial hydriding characteristics, as well as the compositional transformation of composites made of La₂Mg₁₇ + LaNi₅ mechanically milled in a 2:1 weight ratio. Composites produced with varying durations and intensities of milling were tested. Those milled to the greatest extent proved to have the best initial hydrogen absorption and desorption kinetics. The kinetics of the most heavily milled composite were superior to those of La₂Mg₁₇. This composite absorbed 90% of its full hydrogen capacity (3.5 wt.% H₂) in less than 1 min at 250°C and desorbed the same quantity of hydrogen in 6 min. Under the same conditions pure La₂Mg₁₇ took 2.5 h to absorb and 3 h to desorb 90% of its full hydrogen capacity (4.9 wt.% H₂). Scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction were used to characterize the mechanically milled powders before and after hydriding. The unhydrided powders consisted of LaNi₅ grains surrounded by a fractured LaMg₁₇ matrix. Hydrogen cycling, at temperatures up to 350°C, induced phase changes, segregation, and disintegration of the composites. The resulting fine powder (less than 1 μm) consisted primarily of Mg, Mg₂Ni, and La phases.     

Microstructure and electrochemical properties of mechanically ground Ce2Mg17 + x wt.% Ni (x = 0, 50, 100, 200) composites

The effects of mechanical grinding with or without nickel powder on microstructure and electrochemical properties of Ce₂Mg₁₇ hydrogen storage alloy in 6 M KOH solution were investigated. The microstructure and electrochemical properties depend greatly on the amount of nickel powder introduced during mechanical grinding. For the alloy ball-milled with nickel powder, the more nickel powder added, the more advantageous it is for the formation of a homogeneous amorphous structure, and the larger discharge capacity obtained. After 90 h ball-milling, the Ce₂Mg₁₇ + 200 wt.% Ni composite exhibited a large discharge capacity of 1014 mAh g(Ce₂Mg₁₇)⁻¹[338 mAh g(Ce₂Mg₁₇ + 200 wt.% Ni)⁻¹] at 303 K. The improvement of electrochemical capacity can be attributed to the formation of a homogeneous amorphous structure as well as the modification of the surface state by Ni addition.     

Characterization and hydrogenation of CeNi5−xCrx (x = 0, 1, 2) alloys

The effect of partial substitution of Ni by Cr in CeNi₅ intermetallic compound has been studied by pressure–composition isotherm measurements for different temperatures. The samples were prepared of high purity materials using the standard arc melting technique in argon atmosphere. The structure and the elemental composition of different alloys have been investigated by means of XRD, SEM and EDX techniques. The unit cell volume of the alloy was found to increase with increasing Cr content. In order to calculate the hydrogen storage capacity pressure–composition isotherm has been investigated for CeNi_5−xCr_x (x = 1, 2) alloys in the temperature and pressure ranges of 293 ≤ T ≤ 333 K and 0.5 ≤ P ≤ 35 bar, respectively. The P–C–T isotherm for different alloys clearly shows the presence of three regions ,  + β and β. The enthalpy and entropy for the systems has also been calculated using Van’t Hoff plot. The variation of enthalpy and entropy with hydrogen content has also been studied.     

Nanocrystalline LaNi4−xMn0.75Al0.25Cox electrode materials prepared by mechanical alloying (0≤x≤1.0)

Polycrystalline hydrogen storage alloys based on lanthanum (La) are commercially used as negative electrode materials for the nickel–metal hydride (Ni–MH_x) batteries. In this paper, mechanical alloying (MA) was used to synthesize nanocrystalline LaNi_4−xMn_0.75Al_0.25Co_x (x=0, 0.25, 0.5, 0.75 and 1.0) hydrogen storage materials. XRD analysis showed that, after 30 h milling, the starting mixture of the elements decomposed into an amorphous phase. Following the annealing in high purity argon at 700 °C for 0.5 h, XRD confirmed the formation of the CaCu₅-type structures with a crystallite sizes of about 25 nm. The nanocrystalline materials were used as negative electrodes for a Ni–MH_x battery. Cobalt substituting nickel in LaNi₄Mn_0.75Al_0.25 greatly improved the discharge capacity and cycle life of the LaNi₅ material. For example, in the nanocrystalline LaNi_3.75Mn_0.75Al_0.25Co_0.25 powder, discharge capacities up to 258 mA h g⁻¹ (at 40 mA g⁻¹ discharge current) were measured. Mechanical alloying is a suitable procedure to obtain LaNi₅-type alloy powders for electrochemical energy storage.     

The structural and kinetic characteristics of Mg1.9Al0.1Ni alloy synthesized by mechanical alloying

The structural and kinetic characteristics of the mechanically alloyed Mg_1.9Al_0.1Ni were investigated. It was found that Mg_1.9Al_0.1Ni can absorb/desorb about 3.55/3.44 mass% H at a high rate and it has a hexagonal crystal structure as Mg₂Ni. The hydriding/dehydriding (H/D) rates in the two-phase (–β) region of Mg_1.9Al_0.1Ni were measured and studied at temperatures ranging from 553 to 623 K under an approximately isobaric condition. The obtained data of H/D rates indicated that hydrogen diffusion was the rate-controlling step through the hydride phase. A new model was successfully used to calculate the kinetic experimental results. It can be seen that theoretical calculation agrees well with experimental data. The corresponding activation energies are 47 600 and 54 500 J/mol H₂ for H/D processes, respectively.     

镁-镍/石墨烯复合物的储氢性能

分别通过物理法和化学法制备石墨烯载镍催化剂(Ni/Graphene),并采用球磨预处理或超声分散的方式与镁粉混匀,结合氢化燃烧合成和机械球磨复合技术制备镁-镍/石墨烯(Mg-Ni/Graphene)复合物储氢材料。采用X射线衍射仪、扫描电镜及气体反应控制器研究了材料的相组成、微观形貌和吸放氢性能。比较发现,添加化学法制备的Ni/Graphene并采用球磨预处理的Mg-Ni/Graphene复合物具有最佳的吸放氢性能,复合物的起始放氢温度降低,放氢速率加快。其在373 K温度下,100 s内就基本能达到饱和吸氢量6.21%(质量分数);553 K,1800 s内完全放氢,且放氢量达到6.05%。球磨预处理使得Ni/Graphene更均匀的与Mg接触,利于发挥Ni的催化作用和石墨烯优异的导电导热性。化学法制备的Ni/Graphene原位还原出纳米晶Ni,有利于形成纳米级Mg2NiH4晶粒,促进复合物储氢性能的改善。     

Relationship between dielectric properties and structural long-range order in (x)Pb(In1/2Nb1/2)O3:(1 − x)Pb(Mg1/3Nb2/3)O3 relaxor ceramics

The dielectric and structural order–disorder properties of as-sintered complex perovskite (x)Pb(In_1/2Nb_1/2)O₃:(1 − x)Pb(Mg_1/3Nb_2/3)O₃ ceramics are highly influenced by the quantity of Pb(In_1/2Nb_1/2)O₃ (PIN). A high PIN quantity causes the relative permittivity maxima (ε_max) to decrease and the temperature (T_max) to increase. Also, strong frequency dispersion is dominant in the relative permittivity when plotted against the temperature. In ferroelectric hysteresis loop measurements, the maximum values of electric displacements (D_max) decrease with increasing PIN. The ceramics in the composition range x = 0.1–0.8 behave as ferroelectric relaxors and exhibit very slim hysteresis loops for all these compositions. Transmission electron microscopy (TEM) studies show that the size of the 1:1 structural ordered domains is influenced by the PIN quantity. The relationship between the dielectric properties and the long-range 1:1 order in these relaxors appear to be in conflict with the commonly accepted order–disorder behavior in complex perovskite ferroelectrics, in which large structural domains correspond with the tendency to depart from the relaxor state. TEM observations show that individual 1:1 ordered domains in (x)PIN:(1 − x)PMN ceramics are composed of numerous nano-sized ordered domains, separated by fine antiphase boundaries.     

Electrochemical behaviour assessment of novel Mg-rich Mg–Al–RE alloys (RE = Ce, Er)

The electrochemical behaviour of new Mg–Al–RE (RE = Ce, Er) alloys AE91 was investigated in 0.01 M NaCl electrolyte (pH = 12) and compared with that of the most commonly used Mg alloy in the automotive field, the AZ91D. Scanning electron microscopy and quantitative electron probe microanalysis were used to characterize the samples prior to the electrochemical tests. AE91 alloys showed very similar microstructures characterized by a three-phase appearance: a Mg-based solid solution containing only Al and two intermetallic phases γ(Mg₁₇Al₁₂) and (Al_1 − xMg_x)₃Ce or (Al_1 − xMg_x)₂Er. Free corrosion potential measurements, potentiodynamic polarization curves and electrochemical impedance spectroscopy revealed improved passivity behaviour compared to AZ91D alloy. The apparent presence of trace amounts of rare earth oxides in the passive film is presumed to be the reason for the enhanced corrosion resistance of AE91 alloys in the aggressive environment considered.     

Electrochemical properties of the MmNi3.55Mn0.4Al0.3Co0.75−xFex (x = 0.55 and 0.75) compounds

The hydrogen storage alloys MmNi_3.55Mn_0.4Al_0.3Co_0.75−xFe_x (x = 0.55 and 0.75) were used as negative electrodes in the Ni-MH accumulators. The chronopotentiommetry and the cyclic voltammetry were applied to characterize the electrochemical properties of these alloys. The obtained results showed that the substitution of the cobalt atoms by iron atoms has a good effect on the life cycle of the electrode. For the MmNi_3.55Mn_0.4Al_0.3Co_0.2Fe_0.55 compound, the discharge capacity reaches its maximum of 210 mAh/g after 12 cycles and then decreases to 190 mAh/g after 30 charge–discharge cycles. However, for the MmNi_3.55Mn_0.4Al_0.3Fe_0.75 compound, the discharge capacity reaches its maximum of 200 mAh/g after 10 cycles and then decreases to 160 mAh/g after 30 cycles.

The diffusion behavior of hydrogen in the negative electrodes made from these alloys was characterized by cyclic voltammetry after few activation cycles. The values of the hydrogen coefficient in MmNi_3.55Mn_0.4Al_0.3Co_0.2Fe_0.55 and MmNi_3.55Mn_0.4Al_0.3Fe_0.75 are, respectively, equal to 2.96 × 10⁻⁹ and 4.98 × 10⁻¹⁰ cm² s⁻¹. However, the values of the charge transfer coefficients are, respectively, equal to 0.33 and 0.3. These results showed that the substitution of cobalt by iron decreases the reversibility and the kinetic of the electrochemical reaction in these alloys.     

The effect of sequential and continuous high-energy impact mode on the mechano-chemical synthesis of nanostructured complex hydride Mg2FeH6

The effect of sequential and continuous high-energy impact mode in the magneto-mill Uni-Ball-Mill 5 on the mechano-chemical synthesis of nanostructured ternary complex hydride Mg₂FeH₆ was studied by controlled reactive mechanical alloying (CRMA). In the sequential mode the milling vial was periodically opened under a protective gas and samples of the milled powder were extracted for microstructural examination whereas during continuous CRMA the vial was never opened up to 270 h duration. MgO was detected by XRD in sequentially milled powders while no MgO was detected in the continuously milled powder. The abundance of the nanostructured ternary complex hydride Mg₂FeH₆, produced during sequential milling, and estimated from DSC reached 44 wt.% after 188 h, and afterwards it slightly decreased to 42 wt.% after 210 and 270 h. In contrast, the DSC yield of Mg₂FeH₆ after continuous CRMA for 270 h was 57 wt.%. Much higher yield after continuous milling is attributed to the absence of MgO. This behavior provides strong evidence that MgO is a primary factor suppressing formation of Mg₂FeH₆. The DSC hydrogen desorption onset temperatures are close to 200 °C while the desorption peak temperatures for all powders are below 300 °C and the desorption process is completed within the range 10–20 min. Within the investigated nanograin size range of 5–13 nm, the DSC desorption onset and peak temperatures of β-MgH₂ and Mg₂FeH₆ do not exhibit any trend with nanograin (crystallite) size of hydrides. TPD hydrogen desorption peaks from the powders containing a single ternary complex hydride Mg₂FeH₆, are very narrow, which indicates the presence of small but well-crystallized hydride particles. Their narrowness provides good evidence that the phase composition, bulk hydrogen distribution and hydride particle size distribution are very homogeneous. The overall amount of hydrogen desorbed in TPD from single-hydride Mg₂FeH₆ powders is somewhat higher than that observed in DSC and TGA desorption.

The powder milled sequentially for 270 h and desorbed in a Sieverts-type apparatus at 250 and 290 °C, yielded about a half of the hydrogen content obtained during DSC and TGA tests. No desorption of hydrogen was detected in a Sieverts-type apparatus at 250 and 290 °C after 128 and 70 min, respectively, from the powder continuously milled for 270 h. The latter easily desorbed 3.13 and 2.83 wt.% hydrogen in DSC and TGA tests, respectively.     

Cycle stabilities of the La0.7Mg0.3Ni2.55−xCo0.45Mx (M = Fe, Mn, Al; x = 0, 0.1) electrode alloys prepared by casting and rapid quenching

In order to improve the cycle stability of La–Mg–Ni system (PuNi₃-type) hydrogen storage alloy, Ni in the alloy was partly substituted by Fe, Mn and Al, and the electrode alloys La_0.7Mg_0.3Ni_2.55−xCo_0.45M_x (M = Fe, Mn, Al; x = 0, 0.1) were prepared by casting and rapid quenching. The effects of the substitution of Fe, Mn and Al for Ni and rapid quenching on the microstructures and electrochemical properties of the alloys were investigated in detail. The results obtained by XRD, SEM and TEM indicate that element substitution has no influence on the phase compositions of the alloys, but it changes the phase abundances of the alloys. Particularly, the substitution of Al and Mn obviously raises the amount of the LaNi₂ phase. The substitution of Al and Fe leads to a significant refinement of the as-quenched alloy's grains. The substitution of Al strongly restrains the formation of an amorphous in the as-quenched alloy, but the substitution of Fe is quite helpful for the formation of an amorphous phase. The effects of the substitution of Fe, Mn and Al on the cycle stabilities of the as-cast and quenched alloys are different. The positive influence of the substitution elements on the cycle stabilities of the as-cast alloys is in proper order Al > Fe > Mn, and for as-quenched alloys, the order is Fe > Al > Mn. Rapid quenching engenders an inappreciable influence on the phase composition, but it markedly enhances the cycle stabilities of the alloys.     

The effect of Nd content on the electrochemical properties of low-Co La–Mg–Ni-based hydrogen storage alloys

The low-Co content La_0.80−xNd_xMg_0.20Ni_3.20Co_0.20Al_0.20 (x = 0.20, 0.30, 0.40, 0.50, 0.60) alloys were prepared by inductive melting and the effect of Nd content on the electrochemical properties was investigated. XRD shows that the alloys consist mainly of LaNi₅ phase, La₂Ni₇ phase and minor LaNi₃ phase. The electrochemical P–C–T test shows hydrogen storage capacity increases first and then decreases with increasing x, which is also testified by the electrochemical measurement that the maximum discharge capacity increases from 290 mAh/g (x = 0.20) to 374 mAh/g (x = 0.30), and then decreases to 338 mAh/g (x = 0.60). The electrochemical kinetics test shows exchange current density I₀ increases with x increasing from 0.20 to 0.50 followed by a decrease for x = 0.60, and hydrogen diffusion coefficient D increases with increasing x. Accordingly high rate dischargeability increases with a slight decrease at x = 0.60 and the low temperature dischargeability increases with increase in Nd content. When x is 0.50, the alloy exhibits a better cycling stability.     

Synthesis and characterization of LiGaxMn2−xO4 (0 ≤ x ≤ 0.05) by triethanolamine-assisted sol–gel method

Spinel LiGa_xMn_2−xO₄ (0 ≤ x ≤ 0.05) cathode materials with phase-pure particles and nano-sized distribution were synthesized by sol–gel method using triethanolamine as the chelating agent. The effects of heat treatment on the physicochemical properties of the spinel LiGa_xMn_2−xO₄ powders were examined with thermogravimetric and differential thermal analysis (TG/DTA), powder X-ray diffraction (XRD) and scanning electron micrograph (SEM). The LiGa_xMn_2−xO₄ (0 ≤ x ≤ 0.05) electrodes were characterized electrochemically by charge/discharge experiments under a current rate of 0.5C at 55 °C. Although the Ga-doped spinel electrode showed smaller initial discharge capacity, it exhibited better cycling performance than the undoped-LiMn₂O₄ electrode. The dQ/dV versus potential plots at 55 °C revealed that the improvement in cycling performance of the Ga-doped spinel electrode is attributed to stabilization of the spinel structure by the presence of gallium ion.     

Corrosion resistance of (Nd,Dy)16(Fe,Co)76−xTixB8 mechanically alloyed magnets

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at.% of Ti results in increase of coercivity from 796 to 1115 kA/m. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA/m. The highest corrosion resistance have magnets with 0.5–0.75 at.% of Ti. Beside the Ti, the Co and Dy content significantly improve the corrosion resistance, too. It was found, that for Ti content smaller than x ≤ 1, the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x > 1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity as well as corrosion resistance decreases due to the presence of an amorphous phase and -Fe. A heat treatment at a higher temperature (1073 K/30 min) or at 973 K for longer time (1 h) results in the full recrystallisation of the powders. The obtained homogenized structure results in higher corrosion resistance.