Lithium recycling behaviour of nano-phase-CuCo2O4 as anode for lithium-ion batteries

Nano-CuCo₂O₄ is synthesized by the low-temperature (400 °C) and cost-effective urea combustion method. X-ray diffraction (XRD), high resolution transmission electron microscopy (HR-TEM) and selected area electron diffraction (SAED) studies establish that the compound possesses a spinel structure and nano-particle morphology (particle size (10–20 nm)). A slight amount of CuO is found as an impurity. Galvanostatic cycling of CuCo₂O₄ at 60 mA g⁻¹ in the voltage range 0.005–3.0 V versus Li metal exhibits reversible cycling performance between 2 and 50 cycles with a small capacity fading of 2 mAh g⁻¹ per cycle. Good rate capability is also found in the range 0.04–0.94C. Typical discharge and charge capacity values at the 20th cycle are 755(±10) mAh g⁻¹ (∼6.9 mol of Li per mole of CuCo₂O₄) and 745(±10) mAh g⁻¹ (∼6.8 mol of Li), respectively at a current of 60 mA g⁻¹. The average discharge and charge potentials are ∼1.2 and ∼2.1 V, respectively. The underlying reaction mechanism is the redox reaction: Co ↔ CoO ↔ Co₃O₄ and Cu ↔ CuO aided by Li₂O, after initial reaction with Li. The galvanostatic cycling studies are complemented by cyclic voltammetry (CV), ex situ TEM and SAED. The Li-cycling behaviour of nano-CuCo₂O₄ compares well with that of iso-structural nano-Co₃O₄ as reported in the literature.     

Hydrothermal synthesis of Co2SnO4 nanocrystals as anode materials for Li-ion batteries

Cubic spinel Co₂SnO₄ nanocrystals are successfully synthesized via a simple hydrothermal reaction in alkaline solution. The effect of alkaline concentration, hydrothermal temperature, and hydrothermal time on the structure and morphology of the resultant products were investigated based on X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It is demonstrated that pure Co₂SnO₄ nanocrystals with good crystallinity can be obtained in NaOH solution (2.0 M) at 240 °C for 48 h. The galvanostatic charge/discharge and cyclic voltammetry were conducted to measure the electrochemical performance of the Co₂SnO₄ nanocrystals. It is shown that Co₂SnO₄ nanocrystals exhibit good electrochemical activity with high reversible capacity (charge capacity) of 1088.8 mAh g⁻¹ and good capacity retention as anode materials for Li-ion batteries, much better than that of bulk Co₂SnO₄ prepared by high temperature solid-state reaction.     

Comparison between microparticles and nanostructured particles of FeSn2 as anode materials for Li-ion batteries

The performances and mechanisms of two types of anodes formed by FeSn₂ microparticles and nanostructured FeSn₂, respectively, were studied by Mössbauer spectroscopy and electrochemical testing. The specific capacity, which is within the range 400-600 mAh g⁻¹ even at high C-rate, did not vary with cycle number over 50-60 cycles for the microparticles but progressively decreased for the nanostructured material. In the two cases, the first discharge consists in the irreversible transformation of FeSn₂ into Fe/Li₇Sn₂ nanocomposite. The capacity fade is attributed to the growth and/or coalescence of the particles during cycling.     

High power and high capacity cathode material LiNi0.5Mn0.5O2 for advanced lithium-ion batteries

Single-phase lithium nickel manganese oxide, LiNi_0.5Mn_0.5O₂, was successfully synthesized from a solid solution of Ni_1.5Mn_1.5O₄ that was prepared by means of the solid reaction between Mn(CH₃COO)₂·4H₂O and Ni(CH₃COO)₂·4H₂O. XRD pattern shows that the product is well crystallized with a high degree of Li–M (Ni, Mn) order in their respective layers, and no diffraction peak of Li₂MnO₃ can be detected. Electrochemical performance of as-prepared LiNi_0.5Mn_0.5O₂ was examined in the test battery by charge–discharge cycling with different rate, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The cycling behavior between 2.5 and 4.4 V at a current rate of 21.7 mA g⁻¹ shows a reversible capacity of about 190 mAh g⁻¹ with little capacity loss after 100 cycles. High-rate capability test shows that even at a rate of 6C, stable capacity about 120 mAh g⁻¹ is retained. Cyclic voltammetry (CV) profile shows that the cathode material has better electrochemical reversibility. EIS analysis indicates that the resistance of charge transfer (R_ct) is small in fully charged state at 4.4 V and fully discharged state at 2.5 V versus Li⁺/Li. The favorable electrochemical performance was primarily attributed to regular and stable crystal structure with little intra-layer disordering.     

Preparation and electrochemical properties of TiO2 hollow spheres as an anode material for lithium-ion batteries

TiO₂ hollow spheres are fabricated by a sol-gel process using carbon spheres as template. The diameter and the shell thickness of the TiO₂ hollow spheres are about 400-600 nm and 60-80 nm, respectively. The electrochemical properties of the hollow spheres are investigated by galvanostatic cycling and cyclic voltammetry (CV) measurements. The initial discharge capacity reaches 291.2 mAh g⁻¹ at a current density of 60 mA g⁻¹. The average discharge capacity loss is about 1.72 mAh g⁻¹ per cycle from the 2nd to the 40th cycles and the coulombic efficiency is approximately 98% after 40 cycles, indicating excellent cycling stability and reversibility.     

Solvothermal synthesis and ex situ XRD study of nano-Ni3Sn2 used as an anode material for lithium-ion batteries

Nano-Ni₃Sn₂ intermetallic compound was successfully prepared by solvothermal method for an anode material of lithium-ion batteries. Its microstructure was characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). Electrochemical performances were evaluated in a lithium-ion model cell Li/LiPF₆ (EC + DMC)/Ni₃Sn₂. The electrochemical lithiation and de-lithiation behavior of nano-Ni₃Sn₂ was investigated by ex situ XRD. Diffraction peaks of Ni₃Sn₂ widened and shrank gradually during lithiation. Sharp Ni₃Sn₂ peaks appeared again after full de-lithiation. It was proved that nano-Ni₃Sn₂ could be reversibly charged and discharged with lithium though the de-lithiation capacity of nano-Ni₃Sn₂ was lower than its theoretical capacity.     

Preparation and electrochemical properties of carbon-doped TiO2 nanotubes as an anode material for lithium-ion batteries

Carbon-doped TiO₂ nanotubes were synthesized through a sol–gel and subsequent hydrothermal process. Transmission electron microscopy and X-ray diffraction showed that the products are uniformly straight tubes with the diameter around 10 nm in anatase-type. The electrochemical performances of the nanotubes were tested by constant current discharge/charge, cyclic voltammetry, and electrochemical impedance spectroscopy. The initial discharge capacity reaches 291.7 mAh g⁻¹ with a coulombic efficiency of 91.7% at a current density of 70 mA g⁻¹. There is a distinct potential plateau near 1.75 and 1.89 V (versus Li⁺/Li) in the lithium intercalation and extraction processes, respectively, and the lithium insertion capacity is about 204 mAh g⁻¹ over the plateau of 1.75 V region in the first cycle. From the 2nd to the 30th cycles, the average reversible capacity loss is less than 1.73 mAh g⁻¹ per cycle. After 30 cycles, the reversible capacity still remains 211 mAh g⁻¹ with a coulombic efficiency larger than 99.7%, implying a perfect reversibility and cycling stability.     

Characterization of new heterosystem CuFeO2/SnO2 application to visible-light induced hydrogen evolution

Photo-assisted H₂ evolution has been realized over the new heterosystem CuFeO₂/SnO₂ without any noble metal and was studied in connection with some physical parameters. The delafossite CuFeO₂ has been prepared by thermal decomposition from various salts. The polarity of generated voltage is positive indicating that the materials exhibit p-type conductivity whereas the electroneutrality is achieved by oxygen insertion. The plot of the logarithm (conductivity) vs. T⁻¹ gives average activation energy of 0.12 eV. CuFeO₂ is a narrow band gap semiconductor with an optical gap of 1.32 eV. The oxide was characterized photoelectrochemically; its conduction band (−1.09 V_RHE) is located below that of SnO₂ (−0.86 V_RHE) at pH ∼13.5 itself more negative than the H₂O/H₂ level leading to a thermodynamically favorable H₂ evolution under visible irradiation. The sensitizer CuFeO₂, working as an electron pump, is stable towards photocorrosion by hole consumption reactions involving the reducing agents X²⁻ (=S₂O₃²⁻ and SO₃²⁻). The photoactivity was dependent on the precursor and the best performance (0.026 ml h⁻¹ mg⁻¹) was obtained in S₂O₃²⁻ (pH ∼13.5) over CuFeO₂ synthesized from nitrate with a mass ratio (CuFeO₂/SnO₂) equal to unity. A quantum yield of 0.5% was obtained under polychromatic light. H₂ liberation occurs concomitantly with the oxidation of S₂O₃²⁻ to dithionate and sulfate. The tendency towards saturation, in a closed system, is mainly ascribed to the competitive reduction of the end product S₂O₆²⁻.     

A three-dimensional macroporous Cu/SnO2 composite anode sheet prepared via a novel method

A three-dimensional macroporous Cu/SnO₂ composite anode sheet for lithium ion batteries was prepared via a novel method that is based on selective reduction of metal oxides at appropriate temperatures. SnO₂ particles were imbedded on the Cu particles within the three-dimensionally interconnected Cu substrate, and the whole composite sheet was used directly as an electrode without adding extra conductive carbons and binders. Compared with the SnO₂-based electrode prepared via the conventional tape-casting method on Cu foil, the porous Cu/SnO₂ composite electrode shows significantly improved battery performance. This methodology produces limited wastes and is also adaptable to many other materials. It is a promising approach to make macroporous electrode for Li-ion batteries.     

A novel CuO-nanotube/SnO2 composite as the anode material for lithium ion batteries

A novel CuO-nanotubes/SnO₂ composite was prepared by a facile solution method and its electrochemical properties were investigated as the anode material for Li-ion battery. The as-prepared composite consisted of monoclinic-phase CuO-nanotubes and cassiterite structure SnO₂ nanoparticles, in which SnO₂ nanoparticles were dramatically decorated on the CuO-nanotubes. The composite showed higher reversible capacity, better durability and high rate performance than the pure SnO₂. The better electrochemical performance could be attributed to the introducing of the CuO-nanotubes. It was found that the CuO-nanotubes were reduced to metallic Cu in the first discharge cycle, which can retain tube structure of the CuO-nanotubes as a tube buffer to alleviate the volume expansion of SnO₂ during cycling and act as a good conductor to improve the electrical conductivity of the electrodes.     

Visible light-induced hydrogen over CuFeO2 via S2O3 oxidation

The properties of CuFeO₂ have been studied according to the catalytic hydrogen production upon visible light. CuFeO₂ with a low band gap E_g, a good chemical stability and a suitable flat band potential appears as a suitable candidate. The potential of photoelectrons allows favorably a thermodynamically H₂-evolution from alkaline thiosulfate S₂O₃²⁻ solution. There is a major difference between pure and loaded oxide with some metal catalysts. Our best results have been obtained with unloaded CuFeO₂ at 50 °C and pH 13.60. Thiosulfate S₂O₃²⁻ ions can be oxidized to sulfite SO₃²⁻ and subsequently to sulfate SO₄²⁻ and the electronic exchange occurs via mediation of surface states. The quite high H₂-formation at the beginning shows a tendency towards saturation, it competes with SO₃²⁻ produced by parallel oxidation of S₂O₃²⁻.     

Preparation and rate capability of Li4Ti5O12 hollow-sphere anode material

Spinel lithium titanate, Li₄Ti₅O₁₂, with novel hollow-sphere structure was fabricated by a sol–gel process using carbon sphere as template. The effect of the hollow-sphere structure as well as the wall thickness on the Li storage capability and high rate performance was electrochemically evaluated. High specific capacity, especially better high rate performance was achieved with this Li₄Ti₅O₁₂ hollow-sphere electrode material with thin wall thickness. It is believed that this macroporous hollow-sphere structure has shortened the Li diffusion distance, increased the contact area between Li₄Ti₅O₁₂ and electrolyte, and also led to better mixing of the active material with AB. All these factors have resulted in the good rate capability of the hollow-sphere structured Li₄Ti₅O₁₂ electrode material.     

Template-assisted synthesis of high packing density SrLi2Ti6O14 for use as anode in 2.7-V lithium-ion battery

SrLi₂Ti₆O₁₄ has been prepared by using mesoporous TiO₂ brookite as a template and reactant. The prepared particles retained the rounded shape of the precursor, leading to high dispersivity and high packing density. The material has been further electrochemically characterized in both half and full cells. It shows good cycling stability and rate capability. A 2.7-V cell has been built by combining a SrLi₂Ti₆O₁₄ anode with a 4-V spinel cathode of LiMn₂O₄. This cell has a higher voltage compared to the 2.5-V LiMn₂O₄/Li₄Ti₅O₁₂ system.     

Nano Li4Ti5O12–LiMn2O4 batteries with high power capability and improved cycle-life

We report the effects of electrode thickness, cathode particle size and morphology, cathode carbon coating matching ratio and laminate structure on the electrochemical characteristics of nanosized Li₄Ti₅O₁₂–LiMn₂O₄ batteries. We show that a correct adjustment of these parameters resulted in significant improvements in power capability and cycle-life of such devices, making them competitive, low-cost and safe battery chemistry for next generation Li-ion batteries. In addition, Li₄Ti₅O₁₂ reversible specific capacity beyond three Li-ions intercalation is reported.     

Charge–discharge characteristics of all-solid-state thin-filmed lithium-ion batteries using amorphous Nb2O5 negative electrodes

All-solid-state thin-filmed lithium-ion rechargeable batteries composed of amorphous Nb₂O₅ negative electrode with the thickness of 50–300 nm and amorphous Li₂Mn₂O₄ positive electrode with a constant thickness of 200 nm, and amorphous Li₃PO_4−xN_x electrolyte (100 nm thickness), have been fabricated on glass substrates with a 50 mm × 50 mm size by a sputtering method, and their electrochemical characteristics were investigated. The charge–discharge capacity based on the volume of positive electrode increased with increasing thickness of negative electrode, reaching about 600 mAh cm⁻³ for the battery with the negative electrode thickness of 200 nm. But the capacity based on the volume of both the positive and negative electrodes was the maximum value of about 310 mAh cm⁻³ for the battery with the negative electrode thickness of 100 nm. The shape of charge–discharge curve consisted of a two-step for the batteries with the negative electrode thickness more than 200 nm, but that with the thickness of 100 nm was a smooth S-shape curve during 500 cycles.     

Effects of TiO2 coating on high-temperature cycle performance of LiFePO4-based lithium-ion batteries

LiFePO₄ particles were coated with TiO₂ (molar ratio = 3%) via a sol–gel process, and the effects of the coating on cycle performance of LiFePO₄ cathode at 55 °C against either a Li or a C (mesocarbon microbead) anode were investigated. It was found that, while the coating reduces capacity fading of the LiFePO₄/Li cell, it imposes a deteriorating effect on the LiFePO₄/C cell. Analyses on cell impedance and electrode surface morphology and composition showed that the oxide coating reduced Fe dissolution from the LiFePO₄ cathode and hence alleviated the impedance increase associated with the erosion process. This leads to reduced capacity fading as observed for the LiFePO₄/Li cell. However, the oxide coating itself was eroded upon cycling, and the dissolved Ti ions were subsequently reduced at the anode surface. Ti deposit on the C anode was found to be more active than Fe in catalyzing the formation of the solid-electrolyte interphase (SEI) layer, causing accelerated capacity decay for the LiFePO₄/C cell. The results point out the importance of evaluating the effect of cathode coating material on the anode side, which has generally been overlooked in the past studies.     

Cycleable graphite/FeSi6 alloy composite as a high capacity anode material for Li-ion batteries

FeSi₆/graphite composite was prepared by mechanical ball milling. The FeSi₆ alloy particles consist of an electrochemically active silicon phase and inactive phases FeSi₂, distributed uniformly in the graphite matrix. The composite anode offers a large reversible capacity (about 800 mAh g⁻¹) and good cycleability, due to the buffering effect of the inactive FeSi₂ phase and graphite layers on the volumetric changes of Si phase during lithium–Si alloying reaction. Since FeSi₆ alloy is a low-cost industrial material, this alloy compound provides a possible alternative for development of high capacity lithium-ion batteries.     

MoO2 synthesized by reduction of MoO3 with ethanol vapor as an anode material with good rate capability for the lithium ion battery

MoO₂ synthesized through reduction of MoO₃ with ethanol vapor at 400 °C was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Its electrochemical performance as an anode material for lithium ion battery was tested by cyclic voltammetry (CV) and capacity measurements. During the reduction process, the starting material (MoO₃) collapsed into nanoparticles (∼100 nm), on the nanoparticles remains a carbon layer from ethanol decomposition. Rate capacity and cycling performance of the as-prepared product is very satisfactory. It displays 318 mAh g⁻¹ in the initial charge process with capacity retention of 100% after 20 cycles in the range of 0.01–3.00 V vs. lithium metal at a current density of 5.0 mA cm⁻², and around 85% of the retrievable capacity is in the range of 1.00–2.00 V. This suggests the application of this type of MoO₂ as anode material in lithium ion batteries.     

Electrochemical performance of SrF2-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

SrF₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials with improved cycling performance over 2.5–4.6 V were investigated. The structural and electrochemical properties of the materials were studied using X-ray diffraction (XRD), scanning electron microscope (SEM), charge–discharge tests and electrochemical impedance spectra (EIS). The results showed that the crystalline SrF₂ with about 10–50 nm particle size is uniformly coated on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ particles. As the coating amount increased from 0.0 to 2.0 mol%, the initial capacity and rate capability of the coated LiNi_1/3Co_1/3Mn_1/3O₂ decreased slightly owing to the increase of the charge-transfer resistance; however, the cycling stability was improved by suppressing the increase of the resistance during cycling. 4.0 mol% SrF₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ showed remarkable decrease of the initial capacity. 2.0 mol% coated sample exhibited the best electrochemical performance. It presented an initial discharge capacity of 165.7 mAh g⁻¹, and a capacity retention of 86.9% after 50 cycles at 4.6 V cut-off cycling.     

Electrochemical evaluation of rutile TiO2 nanoparticles as negative electrode for Li-ion batteries

Nanosized rutile TiO₂ has been prepared by sol–gel chemistry from a glycerol-modified titanium precursor in the presence of an anionic surfactant. The sample has been characterized by X-ray diffraction, nitrogen sorption, scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and electrochemical tests. Nanosized rutile TiO₂ has been electrochemically investigated using two potential windows: 1.2–3 V and 1–3 V. It exhibits excellent high rates capabilities and good cycling stability.