共查询到20条相似文献,搜索用时 93 毫秒
1.
2.
3.
台阶轴校直工艺计算方法及实验研究 总被引:4,自引:0,他引:4
在研究热处理后台阶轴轴肩处发生弯曲变形的基础上,根据弹塑性力学理论,探讨应力集中对校直过程的影响,提出台阶轴校直工艺计算方法。实验研究表明该方法能有效应用于台阶轴的校直过程,对制定齿轮轴等台阶轴零件校直工艺有一定的指导意义。 相似文献
4.
5.
以往弯曲回弹的研究多是通过单次理论计算或数值模拟方法获取控制回弹的参量,然而理论模型采用了多种近似条件,其计算结果多不能直接用于解决实际问题,难以通过一次校直达到目标精度.数值模拟则对材料模型的要求较高,其模拟结果仅可用于参考.因此,本文提出一种基于挠度的迭代补偿校直算法.针对平面单弧度轴类零件弯曲回弹问题,分别建立了... 相似文献
6.
轴类零件在使用或加工之前,往往需要先经校直,而校直工作通常是由人工或在各种压力机上来完成的,没有专用设备。因此,工作效率不高,操作要求较高。这里介绍一种双联杠杆式触点控制的自动校直机(图1)。采用这种校直机进行轴类零件的校直,既能提高工效,又可以提高校直精度。 相似文献
7.
8.
9.
葛树才 《机械工人(热加工)》1999,(10)
回火冷却校直法 我们用回火后局部冷却的方法校直弯曲的轴类零件,取得了令人满意的效果。现推荐介绍如下: 先在距弯曲的轴类零件两端各四分之一处用铁丝拧做吊挂用的吊扣,使吊挂时,弯曲的轴类零件凸面朝下。待将其回火加热后,挂吊扣将轴类零件浸入水中至轴线处,凹面的一半则露出水面。这时 相似文献
10.
樊思华 《机械工人(热加工)》2010,(11):29-30,34
本文叙述了气体渗碳后铰轴弯曲的情况及校直存在的问题,通过探索和实践,提出用渗碳及后工序正火时冷却的方向性来校直弯曲零件方法,使问题得以解决。本文提出的方法推广至校直花键轴、齿轮轴类零件,效果较好。 相似文献
11.
In a recent paper, the Ritz method with simple algebraic polynomials as trial functions was used to obtain an eigenvalue equation for the free vibration of a class of homogeneous solids with cavities. The method presented is here extended to the study of a class of non-homogeneous solids, in which each solid is composed of a number of isotropic layers with different material properties. The Cartesian coordinate system is used to describe the geometry of the solid which is modelled by means of a segment bounded by the yz, zx and xy orthogonal coordinate planes and by two curved surfaces which are defined by fairly general polynomial expressions in the coordinates x, y and z. The surface representing the interface between two material layers in the solid is also described by a polynomial expression in the coordinates x, y and z. In order to demonstrate the accuracy of the approach, natural frequencies are given for both a two- and three-layered spherical shell and for a homogeneous hollow cylinder, as computed using the present approach, and are compared with those obtained using an exact solution. Results are then given for a number of two- and three-layered cylinders and, to demonstrate the versatility of the approach, natural frequencies are given for a five-layered cantilevered beam with a central circular hole as well as for a number of composite solids of more general shape. 相似文献
12.
13.
通过分析膨胀套在实际使用产生滑移受阻现象、卡死现象原因的实质,并在分析产生问题原因的基础上提出了改进措施即:增加导向机构。 相似文献
14.
15.
设计了磨粉机快辊轴承座的加工工艺和具体的工装夹具.利用卧式加工中心加工磨粉机快辊轴承座,辅以能够高效快速夹紧的夹具,既可以保证加工精度,又能够提高加工效率. 相似文献
16.
一种涡旋压缩机径向随变机构的设计 总被引:1,自引:0,他引:1
详细介绍了运用随变原理设计的一种新型径向密封机构的结构特点,工作原理及主要参数的确定方法,该机构可补偿由于涡旋体加工精度不高而造成的功率损失,适用于涡旋压缩机的批量生产。 相似文献
17.
V. P. Dragunov E. G. Kostsov 《Optoelectronics, Instrumentation and Data Processing》2009,45(3):234-242
Specific features of operation of one- and two-capacitor microelectromechanical converters (MEMC) of energy of mechanical microscopic vibrations into electric energy with a modulated electrode-gap magnitude and with allowance for the mutual influence of electrical and elastic forces are analyzed, and the characteristics of these two devices are compared. The main factors restricting the increase in MEMC power are demonstrated to be the effects of “collapsing” and the condition of conservation of positive rigidity of the system. Expressions for estimating the limiting MEMC parameters are derived. The possibility of electrical energy generation in the presence of “real“ sources of wide-spectrum microscopic vibrations is considered. 相似文献
18.
针对目前市场对工业设计人才的需求,本文论述了我校在工业设计教育方面的改革措施,着重介绍了我校工业设计教育在软件和硬件方面所进行的一系列的改革。 相似文献
19.
20.
本文以某些积算和双笔记录仪产品为例说明由于仪表功能设计的不合理或选型不当,影响了仪表的正常使用,制造厂和用户应关注这类问题。 相似文献