A comparison of temperature distribution in PEMFC with single-phase water cooling and two-phase HFE-7100 cooling methods by numerical study

Thermal management has been considered as one of the critical issues in proton exchange membrane fuel cell (PEMFC). Key roles of thermal management system are maintaining optimal operating temperature of PEMFC and diminishing temperature difference over a single fuel cell and stack. Severe temperature difference causes degradation of performance and deterioration of durability, so understanding temperature distribution inside a single fuel cell and stack is crucial. In this paper, two-phase HFE-7100 cooling method is suggested for PEMFC thermal management and investigated regarding temperature change inside a fuel cell. Also, the results are compared to single-phase water cooling method. Numerical study of temperature distribution inside a single PEMFC is conducted under various conditions for the two different cooling methods. Fuel cell model considering mass transfer, electrochemical reaction and heat transfer is developed.The result indicates that two-phase HFE-7100 cooling method has an advantage in temperature maintenance and temperature uniformity than single-phase water cooling method, especially in high current density region. It is also revealed that the cell temperature is less dependent on system load change with two-phase cooling method. It indicates that the fuel cell system with two-phase cooling method has high thermal stability. In addition, the effect of coolant flow rate and coolant inlet pressure in two-phase HFE-7100 cooling method are discussed. As a result, two-phase cooling method showed reliable cooling performance even with low coolant flow rate and the system temperature increased as coolant pressure rose.     

Model-based decoupling control for the thermal management system of proton exchange membrane fuel cells

As one of the most promising sustainable energy technologies available today, proton exchange membrane fuel cell (PEMFC) engines are becoming more and more popular in various applications, especially in transportation vehicles. However, the complexity and the severity of the vehicle operating conditions present challenges to control the temperature distribution in single cells and stack, which is an important factor influencing the performance and durability of PEMFC engines. It has been found that regulating the input and output coolant water temperature can improve the temperature distribution. Therefore, the control objective in this paper is regulating the input and output temperature of coolant water at the same time. Firstly, a coupled model of the thermal management system is established based on the physical structure of PEMFC engines. Then, in order to realize the simultaneous control of the inlet and outlet cooling water temperature of the PEMFC stack, a decoupling controller is proposed and its closed-loop stability is proved. Finally, based on the actual PEMFC engine platform, the effectiveness, accuracy and reliability of the proposed decoupling controller are tested. The experimental results show that with the proposed decoupling controller, the inlet and outlet temperatures of the PEMFC stack cooling water can be accurately controlled on-line. The temperature error range is less than 0.2 °C even under the dynamic current load conditions.     

Effect of dynamic load on the temperature profiles and cooling response time of a proton exchange membrane fuel cell

Polymer Electrolyte Membrane Fuel Cells (PEMFC) is an electrochemical device that generates electrical energy from the reactions between hydrogen and oxygen. An effective thermal management is needed to preserve the fuel cell performance and durability. Cooling by water is a conventional approach for PEMFC. Balance between optimal operating temperature, temperature uniformity and fast cooling response is a continuous issue in the thermal management of PEMFC. Various cooling strategies have been proposed for water-cooled PEMFC and an approach to obtain a fast cooling response was tested by feeding the coolant at a high temperature. In this paper, the operating behaviour was characterized from the perspectives of temperature profiles, mean temperature difference, and cooling response time. A 2.4 kW water-cooled PEMFC was used and the electrical load ranged from 40 A–90 A. The operating coolant temperature was set to 50 °C where the maximum stack operating temperature is 60 °C. The stack temperature profiles, cooling response time, mean temperature difference and cooling rates to the load variation was analysed. The analysis showed that the strategy allowed a fast cooling response especially at high current densities, but it also promotes a large temperature gradient across the stack.     

A study of operation strategy of cooling module with dynamic fuel cell system model for transportation application

A fuel cell system model with detailed cooling module model was developed to evaluate the control algorithms of cooling module which is used for the thermal management of a proton exchange membrane fuel cell (PEMFC) system. The system model is composed of a dynamic fuel cell stack model and a detailed dynamic cooling module model. To extend modeling flexibility, the fuel cell stack model utilizes analytic approach to capture the transient behavior of the stack temperature corresponding to the change of the coolant temperature and the flow rate during load follow-up. The cooling module model integrated model of fan, water pump, coolant passage, and electric motors so that the model is capable of investigation of operating strategy of pump and fan.The fuel cell system model is applied to the investigation of the control logics of the cooling module. Since, it is necessary for the control of cooling module to define the reference conditions such as coolant temperature and fuel cell stack temperature, this study presents such thermal management criteria. Finally, two control algorithms were compared, a conventional control algorithm and a feedback control algorithm. As a consequence, the feedback control algorithm was found to be more suitable for the cooling module of the PEMFC stack, as they consume less parasitic power while producing more stack power compared to a conventionally controlled cooling module.     

Control-orientated thermal model for proton-exchange membrane fuel cell systems

A lumped parameter dynamic model is developed for predicting the stack temperature, temperatures of the exit reactant gases and coolant water outlet in a proton-exchange membrane fuel cell (PEMFC) system. A dynamic model for a water pump is also developed and can be used along with the thermal model to control the stack temperature. The thermal and water pump models are integrated with the air flow compressor and PEMFC stack current–voltage models developed by Pukrushpan et al. to study the fuel cell system under open and closed-loop conditions. The results obtained for the aforementioned variables from open-loop simulation studies are found to be similar to the experimental values reported in the literature. Closed-loop simulations using the model are carried out to study the effect of stack temperature on settling times of other variables such as stack voltage, air flow rate, oxygen excess ratio and net power of the stack. Further, interaction studies are performed for selecting appropriate input–output pairs for control purpose. Finally, the developed thermal model can assist the designer in choosing the required number of cooling plates to minimize the difference between the cooling water outlet temperature and stack temperature.     

Thermal management for a hydrogen-fueled 1-kW PEMFC based on thermoeconomic analysis

Thermal management is a critical issue in optimizing the performance of proton exchange membrane fuels cells (PEMFC). The heat balance between the heat generation in fuel cell stack (FCS) and the heat removal by coolant liquid determines the operating temperature of the PEMFC and the dehydration or flooding condition in FCS. In this study, the amount of water condensed among all the water produced during the electrochemical reaction in FCS of a hydrogen-fueled 1-kW PEMFC at various conditions was determined using a thermoeconomic method called modified productive structure analysis (MOPSA) and the calculated results were compared with observed ones. The amount of the condensed water which should be removed through the cathode channel is dependent crucially on the cooling rate of FCS, which indicates that thermal management for FCS can be done by controlling of the cooling rate of FCS.     

Thermal characteristics of an air-cooled open-cathode proton exchange membrane fuel cell stack via numerical investigation

In light of stricter emissions regulations and depleting fossil fuel reserves, fuel cell vehicles (FCVs) are one of the leading alternatives for powering future vehicles. An open-cathode, air-cooled proton exchange membrane fuel cell (PEMFC) stack provides a relatively simple electric generation system for a vehicle in terms of system complexity and number of components. The temperature within a PEMFC stack is critical to its level of performance and the electrochemical efficiency. Previously created computational models to study and predict the stack temperature have been limited in their scale and the inaccurate assumption that temperature is uniform throughout. The present work details the creation of a numerical model to study the temperature distribution of an 80-cell Ballard 1020ACS stack by simulating the cooling airflow across the stack. Using computational fluid dynamics, a steady-state airflow simulation was performed using experimental data to form boundary conditions where possible. Additionally, a parametric study was performed to investigate the effect of the distance between the stack and cooling fan on stack performance. Model validation was performed against published results. The temperature distribution across the stack was identical for the central 70% of the cells, with eccentric temperatures observed at the stack extremities, while the difference between coolant and bipolar plate temperatures was approximately 10°C at the cooling channel outlets. The results of the parametric study showed that the fan-stack distance has a negligible effect on stack performance. The assumptions regarding stack temperature uniformity and measurement were challenged. Lastly, the hypothesis regarding the negligible effect of fan-stack distance on stack performance was confirmed.     

Parametric studies of a double-cell stack of PEMFC using Grafoil™ flow-field plates

A parametric study of a double-cell stack of a proton exchange membrane fuel cell (PEMFC) using Grafoil™ flow-field plates is performed. A self-made membrane–electrode assembly (MEA) is used to integrate the PEMFC. Emphasis is placed on the effect of the transport parameters such as cell temperature, pressure and humidity of the reaction side, and flow-field geometry on the performance of the stack. Potential–current and power–current curves are presented. At a fixed dew point of the incoming reactants, say T_dp=30 °C, increasing the cell operating temperature past a threshold value of about 50 °C reduces the cell performance due to membrane dehydration. At a fixed cell operating temperature, a high flow back-pressure increases the cell performance through enhancing the reaction on both electrodes of the fuel cell. Moreover, the cell performance for the pressurised cathode side is better than that for the pressurised anode side due to the favourable back-diffusion of water in the membrane. Finally, empirical correlations are developed to describe the electrode process of the PEMFC stack under various operating conditions.     

Pumpless thermal management of water-cooled high-temperature proton exchange membrane fuel cells

Proton exchange membrane fuel cells (PEMFCs) have been considered for combined heat and power (CHP) applications, but cost reduction has remained an issue for commercialization. Among various types of PEMFC, the high-temperature (HT) PEMFC is gaining more attention due to the simplicity of the system, that will make the total system cost lower. A pumpless cooling concept is introduced to reduce the number of components of a HT PEMFC system even further and also decrease the parasitic power required for operating the system. In this concept, water is used as the coolant, and the buoyancy force caused by the density difference between vapour and liquid when operated above boiling temperate is utilized to circulate the coolant between the stack and the cooling device. In this study, the basic parameters required to design the cooling device are discussed, and the stable operation of the HT PEMFC stack in both the steady-state and during transient periods is demonstrated. It found that the pumpless cooling method provides more uniform temperature distribution within the stack, regardless of the direction of coolant flow.     

High performance PEMFC stack with open-cathode at ambient pressure and temperature conditions

An open-air cathode proton exchange membrane fuel cell (PEMFC) was developed. This paper presents a study of the effect of several critical operating conditions on the performance of an 8-cell stack. The studied operating conditions such as cell temperature, air flow rate and hydrogen pressure and flow rate were varied in order to identify situations that could arise when the PEMFC stack is used in low-power portable PEMFC applications. The stack uses an air fan in the edge of the cathode manifolds, combining high stoichiometric oxidant supply and stack cooling purposes. In comparison with natural convection air-breathing stacks, the air dual-function approach brings higher stack performances, at the expense of having a lower use of the total stack power output. Although improving the electrochemical reactions kinetics and decreasing the polarization effects, the increase of the stack temperature lead to membrane excessive dehydration (loss of sorbed water), increasing the ohmic resistance of the stack (lower performance).     

A critical review of cooling techniques in proton exchange membrane fuel cell stacks

Effective cooling is critical for safe and efficient operation of proton exchange membrane fuel cell (PEMFC) stacks with high power. The narrow range of operating temperature and the small temperature differences between the stack and the ambient introduce significant challenges in the design of a cooling system. To promote the development of effective cooling strategies, cooling techniques reported in technical research publications and patents are reviewed in this paper. Firstly, the characteristics of the heat generation and cooling requirements in a PEMFC stack are introduced. Then the advantages, challenges and progress of various cooling techniques, including (i) cooling with heat spreaders (using high thermal conductivity materials or heat pipes), (ii) cooling with separate air flow, (iii) cooling with liquid (water or antifreeze coolant), and (iv) cooling with phase change (evaporative cooling and cooling through boiling), are systematically reviewed. Finally, further research needs in this area are identified.     

Modeling and thermal management of proton exchange membrane fuel cell for fuel cell/battery hybrid automotive vehicle

The proton exchange membrane fuel cell (PEMFC) stack is a key component in the fuel cell/battery hybrid vehicle. Thermal management and optimized control of the PEMFC under real driving cycle remains a challenging issue. This paper presents a new hybrid vehicle model, including simulations of diver behavior, vehicle dynamic, vehicle control unit, energy control unit, PEMFC stack, cooling system, battery, DC/DC converter, and motor. The stack model had been validated against experimental results. The aim is to model and analyze the characteristics of the 30 kW PEMFC stack regulated by its cooling system under actual driving conditions. Under actual driving cycles (0–65 kW/h), 33%–50% of the total energy becomes stack heat; the heat dissipation requirements of the PEMFC stack are high and increase at high speed and acceleration. A PID control is proposed; the cooling water flow rate is adjusted; the control succeeded in stabilizing the stack temperature at 350 K at actual driving conditions. Constant and relative lower inlet cooling water temperature (340 K) improves the regulation ability of the PID control. The hybrid vehicle model can provide a theoretical basis for the thermal management of the PEMFC stack in complex vehicle driving conditions.     

Design optimization of electric vehicle battery cooling plates for thermal performance

The performance of high-energy battery cells utilized in electric vehicles (EVs) is greatly improved by adequate temperature control. An efficient thermal management system is also desirable to avoid diverting excessive power from the primary vehicle functions. In a battery cell stack, cooling can be provided by including cooling plates: thin metal fabrications which include one or more internal channels through which a coolant is pumped. Heat is conducted from the battery cells into the cooling plate, and transported away by the coolant. The operating characteristics of the cooling plate are determined in part by the geometry of the channel; its route, width, length, etc. In this study, a serpentine-channel cooling plate is modeled parametrically and its characteristics assessed using computational fluid dynamics (CFD). Objective functions of pressure drop, average temperature, and temperature uniformity are defined and numerical optimization is carried out by allowing the channel width and position to vary. The optimization results indicate that a single design can satisfy both pressure and average temperature objectives, but at the expense of temperature uniformity.     

Thermal analysis and management of proton exchange membrane fuel cell stacks for automotive vehicle

The thermal management of a proton exchange membrane fuel cell (PEMFC) is crucial for fuel cell vehicles. This paper presents a new simulation model for the water-cooled PEMFC stacks for automotive vehicles and cooling systems. The cooling system model considers both the cooling of the stack and cooling of the compressed air through the intercooler. Theoretical analysis was carried out to calculate the heat dissipation requirements for the cooling system. The case study results show that more than 99.0% of heat dissipation requirement is for thermal management of the PEMFC stack; more than 98.5% of cooling water will be distributed to the stack cooling loop. It is also demonstrated that controlling cooling water flow rate and stack inlet cooling water temperature could effectively satisfy thermal management constraints. These thermal management constraints are differences in stack inlet and outlet cooling water temperature, stack temperature, fan power consumption, and pump power consumption.     

Modelling of temperature distribution in a solid polymer electrolyte fuel cell stack

The production of electricity in a fuel cell system is associated with the production of an equivalent amount of thermal energy, both for large size power plants and for transportation applications. The heat released by the cells must be removed by a cooling system, characterized by its small size and weight, which must be able to assure uniform work conditions and reduce performance losses. Based upon realistic assumptions, a mathematical model has been developed to determine the temperature and current density distribution in a solid polymer electrolyte fuel cell (SPEFC) stack as a function of operating conditions and stack geometry. The model represents a useful tool to identify operating conditions, such as to have an optimal longitudinal and axial temperature profile, so allowing the design of cooling system and bipolar plates. In this paper, the model has been applied to determine the temperature profile of an experimental SPEFC stack. The model is validated by comparing model results with experimental measurements; simulated and experimental results agree satisfactorily.     

A review of polymer electrolyte membrane fuel cell stack testing

This paper presents an overview of polymer electrolyte membrane fuel cell (PEMFC) stack testing. Stack testing is critical for evaluating and demonstrating the viability and durability required for commercial applications. Single cell performance cannot be employed alone to fully derive the expected performance of PEMFC stacks, due to the non-uniformity in potential, temperature, and reactant and product flow distributions observed in stacks. In this paper, we provide a comprehensive review of the state-of-the art in PEMFC testing. We discuss the main topics of investigation, including single cell vs. stack-level performance, cell voltage uniformity, influence of operating conditions, durability and degradation, dynamic operation, and stack demonstrations. We also present opportunities for future work, including the need to verify the impact of stack size and cell voltage uniformity on performance, determine operating conditions for achieving a balance between electrical efficiency and flooding/dry-out, meet lifetime requirements through endurance testing, and develop a stronger understanding of degradation.     

Water management in a novel proton exchange membrane fuel cell stack with moisture coil cooling

Water flooding causes severe degradation of the performance and lifetime of proton exchange membrane fuel cell (PEMFC). In this study, a novel PEMFC stack with in-built moisture coil cooling was designed and the effects of moisture coil cooling on water management in the new PEMFC stack under various operating conditions were investigated. The result showed that the performance of the PEMFC stack was significantly improved due to the moisture condensation under high current density, high operating temperature, high relative humidity and high operating pressure. The output power was increases by 21.62% (525.71 W) at 1600·mA cm⁻² while the increased parasitic power was no more than 35W. Moreover, degradation of the cathode catalyst layer after 100 h operation was also reduced by using moisture coil cooling. Compared with the situation without moisture condensation, the maximum decay rate of the cathode catalyst layer thickness after 100 h operation was reduced by 13.01%. Accordingly, the novel design is valuable and can be widely used in the future design of PEMFC.     

Experimental investigation on scaling and stacking up of proton exchange membrane fuel cells

The performance of a proton exchange membrane fuel cell (PEMFC) with various flow channel design (serpentine and interdigitated) with different landing to channel ratios (L:C = 1:1; 2:2) for an active area of 25 cm² and 70 cm², for single cell and two cells stack is studied and compared. The effect of back pressure on the PEMFC performance is also investigated. This study establishes a strong relation between back pressure and power output from a PEMFC. It was concluded that the interdigitated flow channel gives better results than the serpentine flow channel configuration for various landing to channel ratios. It was also found that power outputs do not proportionally increase with active area of the membrane electrode assembly (MEA). Similarly, stacking up studies with single cell and two cell stack shows that the two cell stack has reduced power densities when compared to that of a single cell. The effect of cooling channels with natural and forced convection by using induced draught fan on the performance of a PEMFC stack is also studied. Fuel distribution and temperature management are found to be the significant factors which determine the performance of a PEMFC stack.     

Performance of a proton exchange membrane fuel cell stack with thermally conductive pyrolytic graphite sheets for thermal management

This work experimentally investigates the effects of the pyrolytic graphite sheets (PGS) on the performance and thermal management of a proton exchange membrane fuel cell (PEMFC) stack. These PGS with the features of light weight and high thermal conductivity serve as heat spreaders in the fuel cell stack for the first time to reduce the volume and weight of cooling systems, and homogenizes the temperature in the reaction areas. A PEMFC stack with an active area of 100 cm² and 10 cells in series is constructed and used in this research. Five PGS of thickness 0.1 mm are cut into the shape of flow channels and bound to the central five cathode gas channel plates. Four thermocouples are embedded on the cathode gas channel plates to estimate the temperature variation in the stack. It is shown that the maximum power of the stack increase more than 15% with PGS attached. PGS improve the stack performance and alleviate the flooding problem at low cathode flow rates significantly. Results of this study demonstrate the feasibility of application of PGS to the thermal management of a small-to-medium-sized fuel cell stack.     

Thermodynamic analysis of polymer-electrolyte-membrane fuel-cell performance under varying cooling conditions

The cooling capacity and cooling load of a fuel-cell cooling loop govern the operating temperature of the fuel-cell module and its electrical output, efficiency and other thermodynamic aspects. The aim of this work was to analyze the performance of a polymer-electrolyte-membrane fuel-cell (PEMFC) under changing cooling conditions. A back-iteration algorithm was employed to determine the operating temperature of a PEMFC for which thermodynamic performance models were developed for the entropy generation, exergy-destruction and second-law efficiency using an entropy-analysis method. Electrochemical equations for the calculation of the voltage, power and first-law efficiency of the cell were also formulated. A parametric study was performed to evaluate the effects of varying cooling conditions on the energy and exergy efficiency of the PEMFC. The parameters considered include the electric-current density governing the cooling load, the mass flow rate of the coolant and the external thermal resistance of the cooler, which together determine the cooling ability of the fuel-cell cooling loop. Their influences on operating temperature, voltage, power, energy and exergy efficiencies were numerically investigated. The results indicate that although the power output and exhaust heat of PEMFC is mainly dominated by the electric-current density, the impacts of the coolant's mass flow rate and the cooler's external thermal resistance on the voltage, energy and exergy efficiencies of PEMFC module can't be neglected. In the investigated ranges, the gross energy and exergy efficiencies increase with the cooler's external thermal resistance by 3.2% and 2.45%, and decrease with the increase in coolant's mass flow rate by 1.2% and 0.92%, respectively.