Analysis of exhaust waste heat recovery from a dual fuel low temperature combustion engine using an Organic Rankine Cycle

This paper examines the exhaust waste heat recovery potential of a high-efficiency, low-emissions dual fuel low temperature combustion engine using an Organic Rankine Cycle (ORC). Potential improvements in fuel conversion efficiency (FCE) and specific emissions (NO_x and CO₂) with hot exhaust gas recirculation (EGR) and ORC turbocompounding were quantified over a range of injection timings and engine loads. With hot EGR and ORC turbocompounding, FCE improved by an average of 7 percentage points for all injection timings and loads while NO_x and CO₂ emissions recorded an 18 percent (average) decrease. From pinch-point analysis of the ORC evaporator, ORC heat exchanger effectiveness (?), percent EGR, and exhaust manifold pressure were identified as important design parameters. Higher pinch point temperature differences (PPTD) uniformly yielded greater exergy destruction in the ORC evaporator, irrespective of engine operating conditions. Increasing percent EGR yielded higher FCEs and stable engine operation but also increased exergy destruction in the ORC evaporator. It was observed that hot EGR can prevent water condensation in the ORC evaporator, thereby reducing corrosion potential in the exhaust piping. Higher ? values yielded lower PPTD and higher exergy efficiencies while lower ? values decreased post-evaporator exhaust temperatures below water condensation temperatures and reduced exergy efficiencies.     

Effect of exhaust gas recirculation on diesel engine nitrogen oxide reduction operating with jojoba methyl ester

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were carried out in three sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME at various speeds under full load are determined and compared. Secondly, tests were performed at constant speed with two loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Thirdly, the effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light-duty diesel engines. With the application of the EGR method, the CO and HC concentration in the engine-out emissions increased. For all operating conditions, a better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5–15% with very little economy penalty.     

Effect of Exhaust Gas Recirculation (EGR) on performance,emissions, deposits and durability of a constant speed compression ignition engine

To meet stringent vehicular exhaust emission norms worldwide, several exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Exhaust Gas Recirculation (EGR) is a pre-treatment technique, which is being used widely to reduce and control the oxides of nitrogen (NO_x) emission from diesel engines. EGR controls the NO_x because it lowers oxygen concentration and flame temperature of the working fluid in the combustion chamber. However, the use of EGR leads to a trade-off in terms of soot emissions. Higher soot generated by EGR leads to long-term usage problems inside the engines such as higher carbon deposits, lubricating oil degradation and enhanced engine wear. Present experimental study has been carried out to investigate the effect of EGR on soot deposits, and wear of vital engine parts, especially piston rings, apart from performance and emissions in a two cylinder, air cooled, constant speed direct injection diesel engine, which is typically used in agricultural farm machinery and decentralized captive power generation. Such engines are normally not operated with EGR. The experiments were carried out to experimentally evaluate the performance and emissions for different EGR rates of the engine. Emissions of hydrocarbons (HC), NO_x, carbon monoxide (CO), exhaust gas temperature, and smoke opacity of the exhaust gas etc. were measured. Performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC) were calculated. Reduction in NO_x and exhaust gas temperature were observed but emissions of particulate matter (PM), HC, and CO were found to have increased with usage of EGR. The engine was operated for 96 h in normal running conditions and the deposits on vital engine parts were assessed. The engine was again operated for 96 h with EGR and similar observations were recorded. Higher carbon deposits were observed on the engine parts operating with EGR. Higher wear of piston rings was also observed for engine operated with EGR.     

Generating efficiency and NOx emissions of a gas engine generator fueled with a biogas–hydrogen blend and using an exhaust gas recirculation system

This paper investigates the generating efficiency and NO_x emissions of a gas engine generator with a low-pressure loop exhaust gas recirculation system, fueled by a model biogas. Experiments for improving the generating efficiency and reducing NO_x emissions were conducted, utilizing optimum spark timings based on the maximum generating efficiencies with varying exhaust gas recirculation (EGR) rates. The test results show that both the NO_x emissions and the generating efficiency generally decrease when the EGR rate is increased. Also, by utilizing optimum spark timings with varying EGR rates, the addition of hydrogen to the biogas increases the generating efficiency of the engine. In particular, the generating efficiency of the biogas–hydrogen test increased by about 1.5% in comparison with the model biogas test for the optimum spark timing at 15% EGR. Accordingly, comprehensive techniques, such as the use of a biogas–hydrogen fuel mixture and optimum spark timings with respect to EGR rates, should be employed to efficiently generate electricity with a biogas engine.     

Influence of high rates of supplemental cooled EGR on NOx and PM emissions of an automotive HSDI diesel engine using an LP EGR loop

Previous experimental studies on diesel engine have demonstrated the potential of exhaust gas recirculation (EGR) as an in‐cylinder NO_x control method. Although an increase in EGR at constant boost pressure (substitution EGR) is accompanied with an increase in particulate matter (PM) emissions in the conventional diesel high‐temperature combustion (HTC), the recirculation of exhaust gases supplementary to air inlet gas (supplemental EGR) by increasing the boost pressure has been suggested as a way to reduce NO_x emissions while limiting the negative impact of EGR on PM emissions. In the present work, a low‐pressure (LP) EGR loop is implemented on a standard 2.0 l automotive high‐speed direct injection (HSDI) turbocharged diesel engine to study the influence of high rates of supplemental cooled EGR on NO_x and PM emissions. Contrary to initial high‐pressure (HP) EGR loop, the gas flow through the turbine is unchanged while varying the EGR rate. Thus, by closing the variable geometry turbine (VGT) vanes, higher boost pressure can be reached, allowing the use of high rates of supplemental EGR. Furthermore, recirculated exhaust gases are cooled under 50°C and water vapour is condensed and taken off from the recirculated gases. An increase in the boost pressure at a given inlet temperature and dilution ratio (DR) results in most cases an increase in NO_x emissions and a decrease in PM emissions. The result of NO_x–PM trade‐off, while varying the EGR rate at fixed inlet temperature and boost pressure depends on the operating point: it deteriorates at low load conditions, but improves at higher loads. Further improvement can be obtained by increasing the injection pressure. A decrease by approximately 50% of NO_x emissions while maintaining PM emission level, and brake specific fuel consumption can be obtained with supplemental cooled EGR owing to an LP EGR loop, compared with the initial engine configuration (HP moderately cooled EGR). Copyright © 2008 John Wiley & Sons, Ltd.     

Influence of gas velocity on particulate fouling of exhaust gas recirculation coolers

The objective of this research is to study the influence of gas flow velocity on particulate fouling of exhaust gas recirculation (EGR) coolers. An experimental setup has been designed and constructed to simulate particulate fouling in EGR coolers in diesel engines. The setup consists of soot generator, gas/particle flow heater, testing section for EGR coolers and finally an exhaust system. Two sets of fouling experiments have been performed with and without water injection, and the gas velocity in each set has varied between 30, 70 and 120 m/s. The concentration of soot particles in the gas flow is 100 mg/m³, and the average diameter of the particles is 130 nm with a standard deviation of 55 nm. It has been found that the thermal resistance and thickness of the fouling layer and the fouling rate decrease as the gas velocity in the EGR cooler increases. If EGR coolers are operated with a gas velocity, which is just lower than the critical flow velocity for the largest particle in the flow, quick deterioration of the thermal performance of the heat exchanger will nevertheless occur. This strongly indicates that the gas velocity should exceed a certain critical flow velocity in order to prevent particulate fouling. In addition, the presence of water vapour in the gas flow improves the thermal performance of the cooler and decreases the fouling rate, and its influence decreases as the gas velocity increases.     

On-board generation of hydrogen to improve in-cylinder combustion and after-treatment efficiency and emissions performance of a hybrid hydrogen–gasoline engine

Hydrogen on-board fuel reforming has been identified as a waste energy recovery technology with potential to improve Internal combustion engines (ICE) efficiency. Additionally, can help to reduce CO₂, NO_x and particulate matter (PM) emissions. As this thermochemical energy is recovered from the hot exhaust stream and used in an efficient way by endothermic catalytic reforming of petrol mixed with a fraction of the engine exhaust gas. The hydrogen-rich reformate has higher enthalpy than the petrol fed to the reformer and is recirculated to the intake manifold, which will be called reformed exhaust gas recirculation (rEGR).The rEGR system has been simulated by supplying hydrogen (H₂) and carbon monoxide (CO) into a conventional Exhaust Gas Recirculation (EGR) system. The hydrogen and CO concentrations in the rEGR stream were selected to be achievable in practice at typical gasoline exhaust temperatures (temperatures between 300 and 600 °C). A special attention has been paid on comparing rEGR to the baseline ICE, and to conventional EGR. The results demonstrate the potential of rEGR to simultaneously increase thermal efficiency, reduce gaseous emissions and decrease PM formation.Complete fuel reformation can increase the calorific value of the fuel by 28%. This energy can be provided by the waste heat in the exhaust and so it is ideal for combination with a gasoline engine with its high engine-out exhaust temperatures.The aim of this work is to demonstrate that exhaust gas fuel reforming on an engine is possible and is commercially viable. Also, this paper demonstrates how the combustion of reformate in a direct injection gasoline engine via reformed Exhaust Gas Recirculation (rEGR) can be beneficial to engine performance and emissions.     

Hydrogen rich exhaust gas recirculation (H2EGR) for performance improvement and emissions reduction of a compression ignition engine

Hydrogen (H₂), being carbon free energy carrier, is best suitable for compression ignition (CI) engines with better performance and lower carbon derived emissions. Novelty of present study is the employment of low-cost catalyst (alumina) for production of H₂ reformate (hydrogen rich exhaust gas recirculation: H2EGR) in an indigenous catalytic reactor. Experimental tests were carried out on a CI engine under three conditions; base diesel, exhaust gas recirculation (EGR), and H2EGR. Results indicated that brake thermal efficiency of the engine with H2EGR was higher than EGR and comparable with base diesel operation. All carbon-based emissions including smoke emission decreased significantly with H2EGR than diesel and EGR operations. In addition, oxides of nitrogen emission (NO_x) also decreased by about 46% with H2EGR than base diesel operation. It is concluded that H2EGR is a promising option for CI engines for simultaneous reduction of both NO_x and smoke emissions along with the additional benefit of higher efficiency.     

Experimental study of various effects of exhaust gas recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine

Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production and is used on most modern high-speed direct injection (HSDI) diesel engines. However EGR has different effects on combustion and emissions production that are difficult to distinguish (increase of intake temperature, delay of rate of heat release (ROHR), decrease of peak heat release, decrease in O₂ concentration (and thus of global air/fuel ratio (AFR)) and flame temperature, increase of lift-off length, etc.), and thus the influence of EGR on NO_x and particulate matter (PM) emissions is not perfectly understood, especially under high EGR rates. An experimental study has been conducted on a 2.0 l HSDI automotive diesel engine under low-load and part load conditions in order to distinguish and quantify some effects of EGR on combustion and NO_x/PM emissions. The increase of inlet temperature with EGR has contrary effects on combustion and emissions, thus sometimes giving opposite tendencies as traditionally observed, as, for example, the reduction of NO_x emissions with increased inlet temperature. For a purely diffusion combustion the ROHR is unchanged when the AFR is maintained when changing in-cylinder ambient gas properties (temperature or EGR rate). At low-load conditions, use of high EGR rates at constant boost pressure is a way to drastically reduce NO_x and PM emissions but with an increase of brake-specific fuel consumption (BSFC) and other emissions (CO and hydrocarbon), whereas EGR at constant AFR may drastically reduce NO_x emissions without important penalty on BSFC and soot emissions but is limited by the turbocharging system.     

Experimental study of combustion performances and emissions of a spark ignition cogeneration engine operating in lean conditions using different fuels

This work presents an experimental study describing a six-cylinder spark ignition engine running with a lean equivalence ratio, high compression ratio, ignition delay and used in a cogeneration system (heat and electricity production). Three types of fuels; natural gas, pure methane and methane/hydrogen blend (85% CH₄ and 15% H₂ by volume), were used for comparison purposes. Each fuel has been investigated at 1500 rpm and for various engine loads fixed by electrical power output conditions. CO, CO₂, HC, and NOx emissions values, and exhaust gas temperature were measured. The effect of fuel composition on engine characteristics has been studied. The results show, that the hydrogen addition increased HC emissions (around 18%), as well as performance, whilst it reduced NO_x (around 31%), exhaust gas temperature, CO and CO₂.     

高低压EGR系统对低速柴油机性能和排放影响的研究

以某型6缸低速二冲程柴油机为研究对象,建立GT-POWER一维仿真模型,研究高、低压EGR系统对柴油机性能及排放的影响。研究结果表明:随着EGR率的上升,高压EGR系统中压气机运行点从中心高效区向低效区和流量减小的方向移动,而低压EGR系统的流量和压比变化较小;高压EGR系统缸内压力始终低于低压EGR系统,在低负荷时,导致燃烧速度和放热率峰值低于低压EGR系统;燃油消耗率随着EGR率的增加呈上升趋势,当EGR率增加到一定程度时燃油消耗率上升更明显,并且高压EGR系统燃油消耗率明显高于低压EGR;两种EGR系统都能降低NO_x排放,但相同EGR率时,高压EGR系统NO_x减排效果更好。     

Experimental investigation of control of NOx emissions in biodiesel-fueled compression ignition engine

Biodiesel is an alternative fuel consisting of the alkyl esters of fatty acids from vegetable oils or animal fats. Vegetable oils are produced from numerous oil seed crops (edible and non-edible), e.g., rapeseed oil, linseed oil, rice bran oil, soybean oil, etc. Research has shown that biodiesel-fueled engines produce less carbon monoxide (CO), unburned hydrocarbon (HC), and particulate emissions compared to mineral diesel fuel but higher NO_x emissions. Exhaust gas recirculation (EGR) is effective to reduce NO_x from diesel engines because it lowers the flame temperature and the oxygen concentration in the combustion chamber. However, EGR results in higher particulate matter (PM) emissions. Thus, the drawback of higher NO_x emissions while using biodiesel may be overcome by employing EGR. The objective of current research work is to investigate the usage of biodiesel and EGR simultaneously in order to reduce the emissions of all regulated pollutants from diesel engines. A two-cylinder, air-cooled, constant speed direct injection diesel engine was used for experiments. HCs, NO_x, CO, and opacity of the exhaust gas were measured to estimate the emissions. Various engine performance parameters such as thermal efficiency, brake specific fuel consumption (BSFC), and brake specific energy consumption (BSEC), etc. were calculated from the acquired data. Application of EGR with biodiesel blends resulted in reductions in NO_x emissions without any significant penalty in PM emissions or BSEC.     

Effect of exhaust gas recirculation (EGR) temperature for various EGR rates on heavy duty DI diesel engine performance and emissions

DI diesel engines are well established today as the main powertrain solution for trucks and other relevant heavy duty vehicles. At the same time emission legislation (mainly for NO_x and particulate matter) becomes stricter, reducing their limit to extremely low values. One efficient method to control NO_x in order to achieve future emissions limits is the use of rather high exhaust gas recirculation (EGR) rates accompanied by increased boost pressure to avoid the negative impact on soot emissions. The method is based on the reduction of gas temperature level and O₂ availability inside the combustion chamber, but unfortunately it has usually an adverse effect on soot emissions and brake specific fuel consumption (bsfc). The use of high EGR rates creates the need for EGR gas cooling in order to minimize its negative impact on soot emissions especially at high engine load were the EGR flow rate and exhaust temperature are high. For this reason in the present paper it is examined, using a multi-zone combustion model, the effect of cooled EGR gas temperature level for various EGR percentages on performance and emissions of a turbocharged DI heavy duty diesel engine operating at full load. Results reveal that the decrease of EGR gas temperature has a positive effect on bsfc, soot (lower values) while it has only a small positive effect on NO. As revealed, the effect of low EGR temperature is stronger at high EGR rates.     

Natural-gas fueled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions

Natural gas is a fossil fuel that has been used and investigated extensively for use in spark-ignition (SI) and compression-ignition (CI) engines. Compared with conventional gasoline engines, SI engines using natural gas can run at higher compression ratios, thus producing higher thermal efficiencies but also increased nitrogen oxide (NO_x) emissions, while producing lower emissions of carbon dioxide (CO₂), unburned hydrocarbons (HC) and carbon monoxide (CO). These engines also produce relatively less power than gasoline-fueled engines because of the convergence of one or more of three factors: a reduction in volumetric efficiency due to natural-gas injection in the intake manifold; the lower stoichiometric fuel/air ratio of natural gas compared to gasoline; and the lower equivalence ratio at which these engines may be run in order to reduce NO_x emissions. High NO_x emissions, especially at high loads, reduce with exhaust gas recirculation (EGR). However, EGR rates above a maximum value result in misfire and erratic engine operation. Hydrogen gas addition increases this EGR threshold significantly. In addition, hydrogen increases the flame speed of the natural gas-hydrogen mixture. Power levels can be increased with supercharging or turbocharging and intercooling. Natural gas is used to power CI engines via the dual-fuel mode, where a high-cetane fuel is injected along with the natural gas in order to provide a source of ignition for the charge. Thermal efficiency levels compared with normal diesel-fueled CI-engine operation are generally maintained with dual-fuel operation, and smoke levels are reduced significantly. At the same time, lower NO_x and CO₂ emissions, as well as higher HC and CO emissions compared with normal CI-engine operation at low and intermediate loads are recorded. These trends are caused by the low charge temperature and increased ignition delay, resulting in low combustion temperatures. Another factor is insufficient penetration and distribution of the pilot fuel in the charge, resulting in a lack of ignition centers. EGR admission at low and intermediate loads increases combustion temperatures, lowering unburned HC and CO emissions. Larger pilot fuel quantities at these load levels and hydrogen gas addition can also help increase combustion efficiency. Power output is lower at certain conditions than diesel-fueled engines, for reasons similar to those affecting power output of SI engines. In both cases the power output can be maintained with direct injection. Overall, natural gas can be used in both engine types; however further refinement and optimization of engines and fuel-injection systems is needed.     

Influence of EGR unequal distribution from cylinder to cylinder on NOx–PM trade-off of a HSDI automotive Diesel engine

The influence of cylinder-to-cylinder variation in EGR distribution on the NOx–PM trade-off (while varying EGR rate) is studied on an automotive high-speed direct injection Diesel engine. Experiments have been conducted on an engine test bench with and without air-EGR mixer and demonstrate that variations in cylinder-to-cylinder EGR distribution results in a deteriorated NOx–PM trade-off (increased NOx emissions level at a given PM emissions level, or increased PM emissions level at a given NOx emissions level) compared to the well mixed configuration with equal EGR rate for all the cylinders. A qualitative study as well an original experiment is conducted to explain this emissions increase induced by unequal distribution of EGR. When recirculating hot exhaust gases, the emissions increase is due to cylinder-to-cylinder variations in intake gas composition and temperature.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Comparison of the effects of EGR and lean burn on an SI engine fueled by hydrogen-enriched low calorific gas

A naturally aspirated spark ignition (SI) engine fueled by hydrogen-blended low calorific gas (LCG) was tested in both exhaust gas recirculation (EGR) and lean burn modes. The “dilution ratio” was introduced to compare their effects on engine performance and emissions under identical levels of dilution. LCG composed of 40% natural gas and 60% nitrogen was used as a main fuel, and hydrogen was blended with the LCG in volumes ranging from 0 to 20%. The engine test results demonstrated that EGR operations at stoichiometry showed a narrower dilution range, inferior combustion characteristics, lower brake thermal efficiency, faster nitrogen oxides (NO_x) suppression, and higher total hydrocarbon (THC) emissions for all hydrogen blending rates compared to lean burn. These trends were mainly due to the increased oxygen deficiency as a result of using EGR in LCG/air mixtures. Hydrogen enrichment of the LCG improved combustion stability and reduced THC emissions while increasing NO_x. In terms of efficiency, hydrogen addition induced a competition between combustion enhancement and increases in the cooling loss, so that the peak thermal efficiency occurred at 10% H₂ with excess air ratio of 1.5. The engine test results also indicated that a close-to-linear NO_x-efficiency relationship occurred for all hydrogen blending rates in both operations as long as stable combustion was achieved. NO_x versus combustion duration analysis showed that adding H₂ reduced combustion duration while maintaining the same level of NO_x. The methane fraction contained in the THC emissions decreased slightly with an increase in hydrogen enrichment at low EGR or excess air dilution ratios, but this tendency was diminished at higher dilution ratios because of the combined dilution effects from the inert gas in the LCG and the diluents (EGR or excess air).     

H2 effects on diesel combustion and emissions with an LPL-EGR system

In this study, we examined H₂ effects on the combustion and emissions of a diesel engine with low-pressure loop (LPL) exhaust gas recirculation (EGR). We converted a 2.2-L four-cylinder direct-injection diesel engine satisfying Euro5 for H₂ supply. An LPL-EGR system replaced the high-pressure loop (HPL) EGR system. For all tests, the brake mean effective pressure (BMEP) was kept at 4 bar and the EGR ratio was varied from 9 to 42%. The H₂ energy percentage was varied from 0 to 7.4% independently to evaluate the H₂ effects and EGR effects separately. The heat release rate was calculated from the measured cylinder pressure. We found that substitution of H₂ for diesel fuel made the premixed burn fraction larger, and reduced the nitrous oxide (NOx) and particulate matter (PM) emissions simultaneously. For example, the NOx emissions were reduced by 36% for an EGR of 42% and an H₂ percentage of 7.4%. PM emissions were reduced by 18% for an EGR of 35% and an H₂ percentage of 7.4% compared with diesel fuel only cases.     

Effects of low pressure exhaust gas recirculation on regulated and unregulated gaseous emissions during NEDC in a light-duty diesel engine

Regulated and unregulated gaseous emissions with high pressure and low pressure EGR (exhaust gas recirculation) system were tested in a 4-cylinder, light-duty diesel EURO IV engine typically used in European vehicles. Four different engine calibrations with the low pressure EGR system were studied. Regulated emissions of NO_X, CO, HC and CO₂ were measured for each configuration. Unburned Hydrocarbon Speciation, HCHO (formaldehyde), HCOOH (formic acid) and N₂O (nitrous oxide) were also measured in order to determine the MIR (maximum incremental reactivity) of the gaseous emissions. Pollutants were measured without the DOC (diesel oxidation catalyst) to gather data about raw emissions. When the low pressure EGR system was used, decreases in NO_X, N₂O and fuel consumption were observed and significant increases HC, CO and unregulated emissions; this is the result of a lower intake manifold temperature, which provides a higher gas density which modifies the combustion process. The potential of tropospheric ozone production was higher in all cases when the low pressure EGR was used.     

Hydrogen-diesel fuel co-combustion strategies in light duty and heavy duty CI engines

The co-combustion of diesel fuel with H₂ presents a promising route to reduce the adverse effects of diesel engine exhaust pollutants on the environment and human health. This paper presents the results of H₂-diesel co-combustion experiments carried out on two different research facilities, a light duty and a heavy duty diesel engine. For both engines, H₂ was supplied to the engine intake manifold and aspirated with the intake air. H₂ concentrations of up to 20% vol/vol and 8% vol/vol were tested in the light duty and heavy duty engines respectively. Exhaust gas circulation (EGR) was also utilised for some of the tests to control exhaust NO_x emissions.The results showed NO_x emissions increase with increasing H₂ in the case of the light duty engine, however, in contrast, for the heavy duty engine NO_x emissions were stable/reduced slightly with H₂, attributable to lower in-cylinder gas temperatures during diffusion-controlled combustion. CO and particulate emissions were observed to reduce as the intake H₂ was increased. For the light duty, H₂ was observed to auto-ignite intermittently before diesel fuel injection had started, when the intake H₂ concentration was 20% vol/vol. A similar effect was observed in the heavy duty engine at just over 8% H₂ concentration.