Thermal Performance Simulation of a Heat Pump Assisted Solar Desalination System for Kazakhstan Climatic Conditions

ABSTRACT

A numerical model has been proposed in this research work for predicting the energy performance of a heat pump assisted regenerative solar still using phase change heat storage materials such as paraffin wax and hydrate salt. The numerical model is based on energy and mass balance. The performance was simulated for Fort Sherchenko town in Kazakhstan. The performance comparison between the conventional solar still and heat pump assisted regenerative solar still with and without phase change materials are presented. Moreover, the influence of two different phase change materials on thermal performance of a heat pump assisted regenerative solar still are described. The numerical simulation results showed that heat pump assisted regenerative solar still is more energy efficient and produces better productivity when compared to the conventional simple solar still. The use of hydrate salt phase change heat storage material was found to be a good option for enhancing the performance of a heat pump assisted regenerative solar still.     

Numerical study of nanoencapsulated phase change material inside double pipe heat exchanger

Nanoencapsulated phase change material (NPCM) slurry is a dispersion where the phase change material (PCM) is dispersed in fluid. Compared with fluid, these nanofluids have a higher heat capacity during the phase change and a possible enhancement, as a result of this phase change, in the heat transfer phenomenon. To appreciate the merits, in terms of energy, a numerical study has been carried out with fluid based on NPCM inside double pipe heat exchanger. The numerical simulation results have been validated using experimental heat transfer data. The Reynolds and Nusselt numbers have been determined using thermal conductivity and viscosity evaluated in the same conditions as those in numerical model. The results obtained show an improvement of this energetic criterion at low mass flow rate compared with the base fluid. Analysis of the numerical and analytical results reveal that higher inlet flow rate and NPCM concentration results in higher heat transfer rate. In addition, increasing NPCM slurry temperature decreases its performance due to fast melting of PCM inside the tube.     

Hybrid solar parabolic dish power plant and high‐temperature phase change material energy storage system

In this study, a conventional steam power plant with two regenerative boilers is considered, and one of its boilers is replaced with parabolic solar dish collectors and storing the produced thermal energy by the phase change material (PCM) in a storage tank. The results show the necessity of the existence of an auxiliary fired‐gas boiler to provide constant load during the whole 24 hours. The performance of the proposed hybridized system is evaluated through energy and exergy analyses. It was demonstrated that substituting solar collectors with one of the boilers marginally lowers the energy efficiency but increases the exergy efficiency of the whole power plant up to 41.76%. Moreover, it is found out that this hybridization decreases the total irreversibility of the power plant in comparison with the base case, from 51.1 to 47.2 MW. The parametric analysis states that raising the mass flow rate of the heat transfer fluid in the solar collectors not only enhances the system performance but also increases the volume of the PCM tank.     

Thermal characteristics of a volumetric solar absorption system

Solar volumetric heating is one of the alternative clean energy applications, and the improvement of thermal storage capacity of the system is necessary for the efficient applications. Consequently, volumetric solar absorption flow system incorporating the absorber plate in the channel was investigated for different Reynolds numbers and solar concentrations. The influence of the location of the absorbing plate on the heat transfer and hydrodynamic losses was also examined in the channel. In order to increase the thermal storage capacity of the working fluid, phase change materials of 7% concentration was incorporated in the analysis. Lauric acid was used as phase change materials, and water was considered as the carrier fluid in the channel. The performance and pump power loss parameters were introduced to assess the thermal performance of the volumetric solar absorption system. It is found that the performance parameter attained the highest value for the absorber plate location at the top of the channel, which was about 10% higher than those corresponding to the other locations. This was more pronounced with increasing Reynolds number and solar concentration. The pump power loss parameter was the highest for the absorber plate location at the mid‐height of the channel. Copyright © 2013 John Wiley & Sons, Ltd.     

太阳能生活热水系统相变储能研究进展

该文阐述了太阳能生活热水（SDHW）系统用相变材料的选择与封装情况,综述了相变材料在SDHW系统水箱、太阳能集热器和SDHW系统循环中的储能及其改进与强化换热研究进展情况,并对今后SDHW系统相变材料应用发展方向提出建议和展望。研究表明,石蜡与三水醋酸钠应用于SDHW系统水箱和集热器的研究较为广泛,其封装形式主要是的塑料、铝、不锈钢的宏封装,形状为管、柱体、球等,且相变材料加入到传统的SDHW系统中均能提高太阳能生活热水器的储热性能,其储热性能还有较大的提升与改进空间。     

真空管太阳能集热器研究进展

随着太阳能热利用需求的日益增长,真空管太阳能集热器的相关研究得到广泛关注.本文针对空气式真空管太阳能集热器,概述了集热器结构和相变材料对系统热效率的影响,及相变材料与集热器的组合方式,总结了真空管集热器应用中存在的问题,提出了通过改进组合结构以及增加换热面粗糙度提高相变蓄热性能将是重点研究方向.     

An Experimental Investigation on the Effect of Ferrofluids on the Efficiency of Novel Parabolic Trough Solar Collector Under Laminar Flow Conditions

ABSTRACT

The paper is related to the use of magnetic nanofluids (ferrofluids) in a direct absorption solar parabolic trough collector, which enhances thermal efficiency compared to conventional solar collectors. By applying the right magnetic intensity and magnetic field direction, the thermal conductivity of the fluid increased higher than typical nanofluids. Moreover, the ferrofluids exhibit excellent optical properties. The external magnetic source is installed to alter the thermo-physical properties of the fluid, and the absorber tube does not have selective surface allowing ferrofluids to absorb the incoming solar irradiance directly. In this paper, an experimental investigation of the performance of small scale direct absorption solar collector using ferrofluids as an absorber was conducted. Nanoparticle concentrations of 0.05 vol% at the operational temperatures between 19°C and 40°C were used in the current study. The results show that using ferrofluids as a heat transfer fluid increases the efficiency of solar collectors. In the presence of the external magnetic field, the solar collector efficiency increases to the maximum, 25% higher than the conventional parabolic trough. At higher temperatures, the ferrofluids show much better efficiency than conventional heat transfer fluid. The study indicated that nanofluids, even of low-content, have good absorption of solar radiation, and can improve the outlet temperatures and system efficiencies. The study shows the potential of using ferrofluids in the direct absorption solar collector.     

Performance evaluation of a solar thermal energy storage system using nanoparticle-enhanced phase change material

This paper presents a numerical investigation on the thermal performance of a solar latent heat storage unit composed of rectangular slabs combined with a flat-plate solar collector. The rectangular slabs of the storage unit are vertically arranged and filled with phase change material (PCM: RT50) dispersed with high conductive nanoparticles (Al₂O₃). A heat transfer fluid (HTF: water) goes flow in the solar collector and receives solar thermal energy form the absorber area, then circulates between the slabs to transfer heat by forced convection to nanoparticle-enhanced phase change material (NEPCM). A numerical model based on the finite volume method and the conservation equations was developed to model the heat transfer and flow processes in the storage unit. The developed model was validated by comparing the obtained results with the experimental, numerical and theoretical results published in the literature. The thermal performance of the investigated latent heat storage unit combined with the solar collector was evaluated under the meteorological data of a representative day of the month of July in Marrakesh city, Morocco. The effect of the dispersion of high conductive nanoparticles on the thermal behavior and storage performance was also evaluated and compared with the case of base PCM without additives.     

Performance analysis of a latent heat storage system with phase change material for new designed solar collectors in greenhouse heating

The continuous increase in the level of greenhouse gas emissions and the rise in fuel prices are the main driving forces behind the efforts for more effectively utilize various sources of renewable energy. In many parts of the world, direct solar radiation is considered to be one of the most prospective sources of energy. In this study, the thermal performance of a phase change thermal storage unit is analyzed and discussed. The storage unit is a component of ten pieced solar air collectors heating system being developed for space heating of a greenhouse and charging of PCM. CaCl₂6H₂O was used as PCM in thermal energy storage with a melting temperature of 29 °C. Hot air delivered by ten pieced solar air collector is passed through the PCM to charge the storage unit. The stored heat is utilized to heat ambient air before being admitted to a greenhouse. This study is based on experimental results of the PCM employed to analyze the transient thermal behavior of the storage unit during the charge and discharge periods. The proposed size of collectors integrated PCM provided about 18–23% of total daily thermal energy requirements of the greenhouse for 3–4 h, in comparison with the conventional heating device.     

Simulation of CO2 under supercritical pressure in solar collectors by variable Lattice Boltzmann method

Abstract

Supercritical CO₂ is widely used in the HVAC facilities, such as gas coolers and solar collectors. The solar collector is a fluid-filled cavity, and the heat and mass transfer characteristics in the cavity is the key factor that affects the performance of solar collector. Considering that the thermophysical properties of supercritical CO₂ change dramatically, this article employs the Lattice Boltzmann Method (LBM) to implement the numerical simulation of supercritical heat and mass transfer. Based on analysis of the simulate results, it is found that the heat transfer in the solar collector is mainly related to Rayleigh number. Consequently, several correlations for the average Nusselt number are derived using Rayleigh number. Furthermore, a new concept named the critical Rayleigh number is proposed for the bifurcation phenomenon that occurs during the simulation. The numerical simulation results and the newly proposed correlations in this article could be used directly to improve and evaluate the performances of solar collectors.     

Solar multi-mode heating system based on latent heat thermal energy storage and its application

为克服太阳能间断性和不稳定性的缺点进而实现太阳能集热与采暖的能量供需调节和全天候连续供热,提出了基于相变储热的太阳能多模式采暖方法（太阳能集热直接采暖、太阳能集热采暖+相变储热、太阳能相变储热采暖）,并在西藏林芝市某建筑搭建了太阳能与相变储热相结合的采暖系统,该系统可根据太阳能集热温度和外界供热需求实现太阳能多模式采暖的自动控制和自动运行。实验研究表明：在西藏地区采用真空管太阳能集热器可以和中低温相变储热器很好地结合,白天储热器在储热过程中平均储热功率为10.63 kW,储热量达到92.67 kW·h,相变平台明显;晚上储热器在放热过程中供热量达85.23 kW·h,放热功率和放热温度平稳,储放热效率达92%,其储热密度是传统水箱的3.6倍,可连续供热时间长达10 h,从而实现了基于相变储热的太阳能全天候连续供热,相关研究结果对我国西藏地区实施太阳能采暖具有一定的指导作用。     

强化太阳能相变蓄热技术的研究进展

为解决太阳能的间歇性问题,常将其与相变蓄热技术进行结合。与传统显热蓄热相比,相变蓄热可将蓄热能量提高数倍以上,具有巨大的研究和应用价值。本文总结分析了相变蓄热的传热机制及在强化太阳能相变蓄热技术上的研究手段,如变换蓄热结构、添加肋片、使用相变胶囊、充注多相变材料、蓄热材料中添加高导热物质等。分析结果显示,相变传热机制中,融化过程主要考虑对流换热,凝固过程热传导占主导;使用肋片、相变胶囊等,主要增大相变材料接触面与蓄热体的比值,进而改善传热;蓄热材料添加高导热物质,可以改善相变材料的团聚、结核及使用寿命,从而提高导热性能,其中添加泡沫金属效果最为显著。     

Solar water heaters with phase change material thermal energy storage medium: A review

Latent heat thermal energy storage is one of the most efficient ways to store thermal energy for heating water by energy received from sun. This paper summarizes the investigation and analysis of thermal energy storage incorporating with and without PCM for use in solar water heaters. The relative studies are classified on the basis of type of collector and the type of storage used i.e. sensible or latent. A thorough literature investigation into the use of phase change material (PCM) in solar water heating has been considered. It has been demonstrated that for a better thermal performance of solar water heater a phase change material with high latent heat and with large surface area for heat transfer is required.     

Experimental study of a refrigerant charged solar collector

The performance of a heat-pipe solar collector was investigated experimentally using refrigerants R11 as the working fluid. The unit is fabricated locally and its performance is evaluated under Beirut Solar conditions. The heat transfer from the heat pipes to the hot-water storage tank took place through a circular end condenser section of the heat-pipe integrated within the collector frame. Tests of single heat pipes showed that the thermal performance of the heat pipe were dependent on its tilt angle, condenser section length and configuration, and type of internal wick used. A circular condenser end of the heat-pipe performed better than a straight condenser due to increased surface area for heat transfer. The R11-charged solar collector with integrated condenser for secondary cooling of water had an efficiency in early operation hours that reached values higher than 60% for the forced circulation mode. The instantaneous system efficiencies varied from 60 to 20%, which are in the range of conventional water solar collectors. System response was fast and sensitive to the incident solar radiation. The thermosyphonic mode of the system operation generated build up of stored energy in the condenser, resulting in oscillating-type flow thus reducing system efficiency below values obtained with forced circulation. © 1998 John Wiley & Sons, Ltd.     

Heat power capacity of the internal source in light-transparent coatings of planar solar collectors

The results are presented of numerical determination of the heat power capacity of the internal source in light-transparent coatings of planar solar collectors; the power results from partial absorption of the transit total (direct and diffuse) solar radiation and its transfer into heat, as well as from the diffuse solar radiation reflected from the light-absorbing surface of the heat exchange collector panel, are presented.     

Thermal and exergy analysis of solar air collectors with passive augmentation techniques

One of the main disadvantages of solar air collectors in practical applications is their relatively low efficiency. In this experimental investigation, the shape and arrangement of absorber surfaces of the collectors were reorganised to provide better heat transfer surfaces suitable for the passive heat transfer augmentation techniques. The performance of such solar air collectors with staggered absorber sheets and attached fins on absorber surface were tested. The exergy relations are delivered for different solar air collectors. It is seen that the largest irreversibility is occurring at the conventional solar collector in which collector efficiency is smallest.     

Research progress on heat transfer enhancement technology of phase change energy storage

相变储能是通过相变材料吸/放热过程来实现能量储存的技术,它能够解决热量供需时间、空间和强度上的不匹配,并以其高储能密度成为储能领域的研究热点,但由于相变材料的热导率较低,使其应用受到限制。针对相变储能材料熔化/凝固过程中热导率低引起的传热速率慢的问题,从优化储能设备结构、添加剂提高相变材料热导率以及联合强化传热技术三方面综述国内外相变材料储能强化传热技术的最新进展。通过比较各种强化传热方式的优劣,实验和模拟均显示复合强化传热即可解决相变材料热导率低,又增大传热面积,从而提高相变材料的传热性能;多孔金属作为导热添加剂增强导热效果更好;并提出了相变储能强化传热技术未来需要解决的相关技术难题。     

Numerical analysis of latent heat thermal energy storage using encapsulated phase change material for solar thermal power plant

Thermal energy storage improves the load stability and efficiency of solar thermal power plants by reducing fluctuations and intermittency inherent to solar radiation. This paper presents a numerical study on the transient response of packed bed latent heat thermal energy storage system in removing fluctuations in the heat transfer fluid (HTF) temperature during the charging and discharging period. The packed bed consisting of spherical shaped encapsulated phase change materials (PCMs) is integrated in an organic Rankine cycle-based solar thermal power plant for electricity generation. A comprehensive numerical model is developed using flow equations for HTF and two-temperature non-equilibrium energy equation for heat transfer, coupled with enthalpy method to account for phase change in PCM. Systematic parametric studies are performed to understand the effect of mass flow rate, inlet charging system, storage system dimension and encapsulation of the shell diameter on the dynamic behaviour of the storage system. The overall effectiveness and transient temperature difference in HTF temperature in a cycle are computed for different geometrical and operational parameters to evaluate the system performance. It is found that the ability of the latent heat thermal energy storage system to store and release energy is significantly improved by increasing mass flow rate and inlet charging temperature. The transient variation in the HTF temperature can be effectively reduced by decreasing porosity.     

Review on storage materials and thermal performance enhancement techniques for high temperature phase change thermal storage systems

Designing a cost-effective phase change thermal storage system involves two challenging aspects: one is to select a suitable storage material and the other is to increase the heat transfer between the storage material and the heat transfer fluid as the performance of the system is limited by the poor thermal conductivity of the latent heat storage material. When used for storing energy in concentrated solar thermal power plants, the solar field operation temperature will determine the PCM melting temperature selection. This paper reviews concentrated solar thermal power plants that are currently operating and under construction. It also reviews phase change materials with melting temperatures above 300 °C, which potentially can be used as energy storage media in these plants. In addition, various techniques employed to enhance the thermal performance of high temperature phase change thermal storage systems have been reviewed and discussed. This review aims to provide the necessary information for further research in the development of cost-effective high temperature phase change thermal storage systems.     

Parametric Analysis of Solar Heating and Cooling Systems for Residential Applications

Abstract

In this paper, a parametric analysis of two solar heating and cooling systems, one using an absorption heat pump and the other one using an adsorption heat pump, was performed. The systems under investigation were designed to satisfy the energy requirements of a residential building for space heating/cooling purposes and domestic hot water production. The system with the absorption heat pump was analyzed upon varying (i) the solar collectors’ area, (ii) the volume of the hot water storage, (iii) the volume of the cold water tank, and (iv) the climatic conditions. The system with the adsorption heat pump was evaluated upon varying (i) the inlet temperature of hot water supplied to the adsorption heat pump, (ii) the volume of the hot water storage, (iii) the volume of the cold water tank, and (iv) the climatic conditions. The analyses were performed using the dynamic simulation software TRNSYS in terms of primary energy consumption, global carbon dioxide equivalent emissions, and operating costs. The performance of the solar heating and cooling systems was compared with those associated with a conventional system from energy, environmental and economic points of views in order to evaluate the potential benefits.