Biological nutrient removal in membrane bioreactors: denitrification and phosphorus removal kinetics.

The impact of including membranes for solid liquid separation on the kinetics of nitrogen and phosphorus removal was investigated. To achieve this, a membrane bioreactor (MBR) biological nutrient removal (BNR) activated sludge system was operated. From batch tests on mixed liquor drawn from the MBR BNR system, denitrification and phosphorus removal rates were delineated. Additionally the influence of the high total suspended solids concentrations present in the MBR BNR system and of the limitation of substrate concentrations on the kinetics was investigated. Moreover the ability of activated sludge in this kind of system to denitrify under anoxic conditions with simultaneous phosphate uptake was verified and quantified.The denitrification rates obtained for different mixed liquor (ML) concentrations indicate no effect of ML concentration on the specific denitrification rate. The denitrification took place at a single specific rate (K(2)) with respect to the ordinary heterotrophic organisms (OHOs, i.e. non-PAOs) active mass. Similarly, results have been obtained for the P removal process kinetics: no differences in specific rates were observed for different ML or substrate concentrations. From the P removal batch tests results it seems that the biological phosphorus removal population (PAO) consists of 2 different sets of organisms denitrifying PAO and aerobic PAO.     

Nitrogen removal in a fluidized bed bioreactor by using mixed culture under oxygen-limited conditions.

Nitrogen removal involving nitrification and denitrification was investigated in a fluidized bed bioreactor by using mixed culture sludge under oxygen-limited conditions. Methane was used as a sole carbon source for denitrification. In this study, optimal nitrification and denitrification rates were examined by varying methane and oxygen gas dissolution flow rates, 90 ml/min, 400 ml/min and 650 ml/min, in each. Simultaneously nitrification and denitrification was achieved. The total nitrogen removal rate was 15-mg N/g VSS. d, 21-mg N/g VSS. d and 26.4-mg N/g VSS. d at gas dissolution flow rate 90 ml/min, 400 ml/min and 650 ml/min, respectively. No significant accumulation of nitrite was found in this experiment. Nitrogen removal rates depend on gas dissolution flow rates. DO concentration was at 0.5-2 mg/L.     

Factors affecting nitrogen removal by nitritation/denitritation.

Nitrogen removal from wastewater with high nitrogen concentration and low COD/N ratio via nitrite is advantageous. The specific character of the sludge liquor enables the application of such a method. The factors affecting process efficiency were studied. From the factors followed pH, NH4+/NH3 and NO2-/HNO2 concentration and distribution seem to be most important, using sequencing batch reactor technology and treating wastewater with high NH4+ concentration (above 1 g/l). The efficient oxidation of N-NH4+ to nitrite was achieved at a minimal nitrate production. Primary sludge was used as an internal source of substrate for the denitritation because of the organic substrate deficiency of the sludge liquor. The denitritation can be controlled by dosing of the primary sludge and can be complete. There are two operational alternatives of sludge liquor pretreatment: without pH control--lower operational costs and N-removal up to 65% and with pH control--higher operational costs and N-removal close to complete.     

Post-aeration of anaerobically digested sewage sludge for advanced COD and nitrogen removal: results and cost-benefit analysis at large-scale.

At a large Austrian municipal wastewater treatment plant enhanced stabilisation of anaerobically digested sewage sludge was required in order to get a permit for landfill disposal of the dewatered stabilized sludge. By implementing a post-aeration treatment after anaerobic digestion the organic content of the anaerobically well digested sludge can be decreased by 16%. Investigations at this plant showed that during digested sludge post-aeration anoxic phases are needed to provide stable process conditions. In this way the pH value can be kept in a more favourable range for micro-organisms and concrete structures. Additionally, under the process conditions applied nitrite accumulation would inhibit the stabilisation process if denitrification is not adequately applied. By optimising the aeration/pause ratio approximately 45% of total nitrogen in digested sludge can be removed. NH4-removal occurs through nitrification and denitrification with an efficiency of 98%. This significantly improves nitrogen removal efficiency at the wastewater treatment plant. The costs/benefit analysis shows that post-aeration of digested sludge results in an increase of total annual costs for wastewater treatment of only 0.84%, corresponding to 0.19 Euro/pe/a. Specific costs for nitrogen removal (0.32 Euro/kgN) are comparable with other biological processes for N-removal in reject water.     

Alternate anoxic/aerobic operation for nitrogen removal in a membrane bioreactor for municipal wastewater treatment

A large pilot-scale membrane bioreactor (MBR) with a conventional denitrification/nitrification scheme for municipal wastewater treatment has been run for one year under two different aeration strategies in the oxidation/nitrification compartment. During the first five months air supply was provided according to the dissolved-oxygen set-point and the system run as a conventional predenitrification MBR; then, an intermittent aeration strategy based on effluent ammonia nitrogen was adopted in the aerobic compartment in order to assess the impact on process performances in terms of N and P removal, energy consumption and sludge reduction. The experimental inferences show a significant improvement of the effluent quality as COD and total nitrogen, both due to a better utilization of the denitrification potential which is a function of the available electron donor (biodegradable COD) and electron acceptor (nitric nitrogen); particularly, nitrogen removal increased from 67% to 75%. At the same time, a more effective biological phosphorus removal was observed as a consequence of better selection of denitrifying phosphorus accumulating organisms (dPAO). The longer duration of anoxic phases also reflected in a lower excess sludge production (12% decrease) compared with the standard pre-denitrification operation and in a decrease of energy consumption for oxygen supply (about 50%).     

SHARON process evaluated for improved wastewater treatment plant nitrogen effluent quality.

New stricter nitrogen effluent standards and increasing influent loads require existing wastewater treatment plans (WWTPs) to extend or optimize. At WWTPs with limited aeration capacity, limited denitrification capacity or shortage of aerobic sludge age, implementation of SHARON to improve nitrogen effluent quality can be a solution. SHARON is a compact, sustainable and cost-effective biological process for treatment of nitrogen-rich rejection waters. At WWTP Rotterdam-Dokhaven and WWTP Utrecht a SHARON has been in operation for several years. For both WWTPs the effect of SHARON on the nitrogen effluent quality has been evaluated. WWTP Rotterdam-Dokhaven has limited aeration capacity. By implementation of SHARON, the ammonia load of the effluent was reduced by 50%. WWTP Utrecht had limited denitrification capacity. The implementation of SHARON improved the effluent nitrate load by 40%. The overall TN removal efficiency increased from 65% to over 75% and strict nitrogen effluents standards (TN = 10 mg N/l) could be reached. Through modelling and supported by full scale practice it has been shown that by implementation of SHARON in combination with enhanced influent pre-treatment, the aerobic sludge age can be extended to maintain total nitrogen removal at lower temperatures.     

ABR反应器对垃圾渗滤液的处理试验研究

ABR工艺在处理垃圾渗滤液中具有其他厌氧生物反应器所达不到的优点。尤其是对B/C低、氨氮浓度高、COD浓度高的废水处理,通过调节回流比、HRT、碱度等参数后,可以取得很好的处理效果。在本次实验中,HRT控制在18h后明显提高的垃圾渗滤液的可生化性及C/N,使ABR出水CODcr去除率达到75%,C/N为6.72,对后续好氧反应起到了重要作用。在调控一定回流比后,为提供厌氧氨氧化所需的电子受体NO-3和NO-2实现脱氮。反应器在经过120d的培养驯化,氨氮进水为460mg/L,ABR对氨氮的去除率稳定在80%。不同格室的厌氧颗粒污泥都得到很好的驯化并在其合适的环境中发挥各自的功能。     

Nitrogen removal from sludge digester liquids by nitrification/denitrification or partial nitritation/anammox: environmental and economical considerations.

In wastewater treatment plants with anaerobic sludge digestion, 15-20% of the nitrogen load is recirculated to the main stream with the return liquors from dewatering. Separate treatment of this ammonium-rich digester supernatant significantly reduces the nitrogen load of the activated sludge system. Two biological applications are considered for nitrogen elimination: (i) classical autotrophic nitrification/heterotrophic denitrification and (ii) partial nitritation/autotrophic anaerobic ammonium oxidation (anammox). With both applications 85-90% nitrogen removal can be achieved, but there are considerable differences in terms of sustainability and costs. The final gaseous products for heterotrophic denitrification are generally not measured and are assumed to be nitrogen gas (N2). However, significant nitrous oxide (N2O) production can occur at elevated nitrite concentrations in the reactor. Denitrification via nitrite instead of nitrate has been promoted in recent years in order to reduce the oxygen and the organic carbon requirements. Obviously this "achievement" turns out to be rather disadvantageous from an overall environmental point of view. On the other hand no unfavorable intermediates are emitted during anaerobic ammonium oxidation. A cost estimate for both applications demonstrates that partial nitritation/anammox is also more economical than classical nitrification/denitrification. Therefore autotrophic nitrogen elimination should be used in future to treat ammonium-rich sludge liquors.     

Characteristics of denitrifying granular sludge grown on nitrite medium in an upflow sludge blanket (USB) reactor

While inoculating pre-acclimatized floccular sludge, nitrite-denitrifying granular sludge was obtained after approximately 40 days of cultivation in a 10 L upflow sludge blanket (USB) reactor. The nitrite removal efficiency was approximately 95% when the nitrite concentration was 50 mg L(-1)at an influent flow rate of 20 L h(-1). The nitrite granular sludge had several notable features including good settleability (110 m h(-1)), high ash content (79%), and high density (1.248 g cm(-3)). The mixed liquor suspended solids (MLSS) of the sludge bed remained at 130.04 g L(-1), at a hydraulic upflow velocity of 2 m h(-1). These interesting characteristics were attributed to a high effluent pH (9.7) caused by the release of alkalinity during the nitrite denitrification process. The surfaces of the granules were dominated by cocci bacteria with a diameter of approximately 3 μm, which could be classi?ed as Nitrosomonas-like species based on our analysis of 16 S rDNA sequences.     

Pilot scale evaluation of SANI process for sludge minimization and greenhouse gas reduction in saline sewage treatment

This study reports on a pilot trial of the SANI process (Sulfate reduction, Autotrophic denitrification and Nitrification Integrated process) in Hong Kong. A pilot-scale SANI plant treating saline sewage at 10 m3/day was scaled-up from a lab-scale system treating synthetic saline sewage. The plant consisted of a sulfate reduction up-flow sludge bed (SRUSB), an anoxic bioreactor (BAR1) for autotrophic denitrification utilizing dissolved sulfide produced by the SRUSB and an aerobic bioreactor (BAR2) for nitrification. The SANI pilot plant was successfully operated for 225 days and achieved average COD, TSS, TN removal of 87, 87, and 57%, respectively. The ratio of MLVSS to MLSS in the SRUSB was stable at 0.7 and the average sludge volume index (SVI) was constantly below 110 ml/g. No sludge was purposely withdrawn from the plant during 225-day plant operation. This was attributed to a very low observed sludge yield (0.02 kgVSS/kgCOD removed) of the SRUSB reactor. DNA extraction, PCA amplification results revealed that no methanogens were detected in the SRUSB. SANI can reduce 90% sludge production, 35% energy and 36% GHG compared to conventional biological nutrient removal (CBNR) process.     

Development and optimisation of VFA driven DEAMOX process for treatment of strong nitrogenous anaerobic effluents.

The recently proposed DEAMOX (DEnitrifying AMmonium OXidation) process combines the anammox reaction with autotrophic denitrifying conditions using sulphide as an electron donor for the production of nitrite from nitrate within an anaerobic biofilm. This paper firstly presents a feasibility study of the DEAMOX process using synthetic (ammonia + nitrate) wastewater where sulphide is replaced by volatile fatty acids (VFA) as a more widespread electron donor for partial denitrification. Under the influent N-NH+4/N-NO3(-) and COD/N-NO3(-) ratios of 1 and 2.3, respectively, the typical efficiencies of ammonia removal were around 40% (no matter whether a VFA mixture or only acetate were used) for nitrogen loading rates (NLR) up to 1236 mg N/l/d. This parameter increased to 80% by increasing the influent COD/N-NO3(-) ratio to 3.48 and decreasing the influent N-NH4 +/N-NO3(-) ratio to 0.29. As a result, the total nitrogen removal increased to 95%. The proposed process was further tested with typical strong nitrogenous effluent such as reject water (total N, 530-566 mg N/l; total COD, 1530-1780 mg/l) after thermophilic sludge anaerobic digestion. For this, the raw wastewater was split and partially ( approximately 50%) fed to a nitrifying reactor (to generate nitrate) and the remaining part ( approximately 50%) was directed to the DEAMOX reactor where this stream was mixed with the nitrified effluent. Stable process performance up to NLR of 1,243 mg N/l/d in the DEAMOX reactor was achieved resulting in 40, 100, and 66% removal of ammonia, NOx(-), and total nitrogen, respectively.     

A novel wastewater treatment process: simultaneous nitrification, denitrification and phosphorus removal.

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen concentration (DO, 0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to polyhydroxyalkanoates (PHA), accompanied with phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to less than 0.5 mg/L at the end of the cycle. Ammonia was also oxidised during the aerobic period, but without accumulation of nitrite or nitrate in the system, indicating the occurrence of simultaneous nitrification and denitrification. However, off-gas analysis found that the final denitrification product was mainly nitrous oxide (N2O) not N2. Further experimental results demonstrated that nitrogen removal was via nitrite, not nitrate. These experiments also showed that denitrifying glycogen-accumulating organisms rather than denitrifying polyphosphate-accumulating organisms were responsible for the denitrification activity.     

New anaerobic process of nitrogen removal.

This paper reports on successful laboratory testing of a new nitrogen removal process called DEAMOX (DEnitrifying AMmonium OXidation) for the treatment of strong nitrogenous wastewater such as baker's yeast effluent. The concept of this process combines the recently discovered ANAMMOX (ANaerobic AMMonium OXidation) reaction with autotrophic denitrifying conditions using sulfide as an electron donor for the production of nitrite within an anaerobic biofilm. The achieved results with a nitrogen loading rate of higher than 1,000 mg/L/d and nitrogen removal of around 90% look very promising because they exceed (by 9-18 times) the corresponding nitrogen removal rates of conventional activated sludge systems. The paper describes also some characteristics of DEAMOX sludge, as well as the preliminary results of its microbiological characterization.     

Effects of influent COD/N ratio and internal recycle ratio on nitrogen removal efficiency in the KNR process.

In this study, with the KNR process that has many advantages, the nitrogen removal efficiency of KNR was experimentally investigated at various COD/N ratios of influent conditions. The optimal operating condition of internal recycle ratio was evaluated. The TN removal efficiencies were 59.1, 72.5 and 75.9% at the COD/N ratios of 3, 5 and 7, respectively. These high removal efficiencies resulted from high denitrification rate in UMBR with high microorganism concentration. Furthermore, specific endogenous denitrification at MLVSS of 10.3 g/L that is similar to MLVSS in UMBR was over two times higher than that at MLVSS of 2.06 g/L. This result suggests that endogenous denitrification rate in UMBR is so high that the requirement of an external carbon source can be saved. As the internal recycle ratio increased from 100 to 400%, the TN removal efficiency also improved from 69.5 to 82.9%, and the optimal internal recycle ratio was 300%.     

Effect of C/N ratio on nitrous oxide emission from swine wastewater treatment process.

To evaluate control parameters for nitrous oxide (N2O) emissions in the swine wastewater treatment process, the N2O emission was compared in the activated sludge from SBRs acclimated in different carbon/nitrogen (C/N) ratios. N2O emission from a denitrification phase was very strongly dependent on C/N ratio of swine wastewater, and the total N2O emission in the operating condition of BOD5/TN ratio of 2.6 was approximately 270 times greater than that in BOD5/TN ratio of 4.5. However, the effect of C/N ratio on N2O emission amount from nitrification was not significant in an oxic phase study. It is considered that stabilization of the C/N ratio through optimal solid-liquid separation of slurry or use of an external carbon source is indispensable for effective N2O emission control from nitrogen removal process of swine wastewater.     

Simultaneous biological removal of sulphide and nitrate by autotrophic denitrification in an activated sludge system.

The feasibility of an autotrophic denitrification process in an activated sludge reactor, using sulphide as the electron donor, was tested for simultaneous denitrification and sulphide removal. The reactor was operated at nitrate (N) to sulphide (S) ratios between 0.5 and 0.9 to evaluate their effect on the N-removal efficiency, the S-removal efficiency and the product formation during anoxic oxidation of sulphide. One hundred per cent removal of both nitrate and sulphide was achieved at a NLR of 7.96 mmol N-L(-1) x d(-1) (111.44 mg NO3- -N x L(-1) x d(-1)) and at a N/S ratio of 0.89 with complete oxidation of sulphide to sulphate. The oxygen level in the reactor (10%) was found to influence the N-removal efficiency by inhibiting the denitrification process. Moreover, chemical (or biological) oxidation of sulphide with oxygen occurred, resulting in a loss of the electron donor. FISH analysis was carried out to study the microbial population in the system.     

A two-sludge system for simultaneous biological C, N and P removal via the nitrite pathway

Nitrogen removal via the nitrite pathway results in significant savings in both aeration costs and COD requirements for denitrification when compared to the conventional biological nitrogen removal process. Implementation of the nitrite pathway for simultaneous C/N/P removal in a single sludge system has a major drawback: the aeration phase disfavours denitrifying phosphorus removal. A possible configuration to overcome this issue is the utilisation of a two-sludge system where autotrophic and heterotrophic populations are physically separated. This paper experimentally demonstrates the feasibility of a nitrite-based two-sludge system with sequencing batch reactors (SBR) for the treatment of urban wastewater: a heterotrophic SBR with denitrifying PAOs for P removal and an aerobic SBR for N removal. Partial nitrification was attained in the autotrophic SBR so that shortcut biological nitrogen removal was achieved by using the anoxic dephosphatation activity of DPAOs. Finally, the effect of operating this system without pH control was studied using different influent pH values (pH = 6.8, 7.5 and 8.2) and, despite some efficiency lost due to the pH fluctuations, the system was able to remove most of the C, N and P present in the wastewater.     

不同电子受体的反硝化除磷效果对比研究

反硝化除磷作用可以明显节省脱氮除磷过程的碳源需求和能耗。为研究不同电子受体下的反硝化除磷效果,利用一体化活性污泥工艺中污泥经过厌氧释磷后在不同电子受体下进行反硝化除磷试验,结果表明NO3-—N和NO2-—N均能参与反硝化除磷过程,在NO2-—N初始浓度高达30mg/L的条件下,除磷率仍在93%以上,未对反硝化除磷过程产生毒害作用。在工程应用中应加强短程硝化反硝化与反硝化除磷作用的耦合,在提高脱氮除磷效率的同时,取得明显的节能效果。     

Treatment of landfill leachate by a pilot-scale modified Ludzack-Ettinger and sulfur-utilizing denitrification process.

Nitrogen removal efficiency of a pilot-scale system consisted of Modified Ludzack-Ettinger (MLE) followed by sulfur-utilizing denitrification (SUDNR) process was evaluated with a landfill leachate. For SUDNR, a down-flow mode sulfur packed bed reactor (SPBR) filled with sulfur and limestone particles was used. Although total nitrogen removal efficiency of the MLE process was about 80% at the recycle ratio of 4, effluent contained 350-450 mg/L NO(3-)-N. Up to a loading rate of 1.2 kg NO(3-)-N/m3-day, the SPBR could achieve complete removal of nitrate, and nitrate removal rate was kept to that level even at higher loading rate. When a COD/N ratio of MLE process was maintained at 2 instead of 4, more organics with molecular weight less than 500 were utilized for heterotrophic denitrification although denitrification was not complete with the lack of electron donors. Clogging in the SPBR, mainly by the accumulation of nitrogen gas in the pores, could easily be removed by introducing the effluent in an upward direction for 1 min at 1 hr intervals. The proposed treatment system could achieve nitrate free effluent with a slight increase in chemical cost. Furthermore, depending on further COD removal requirement after biological treatment, the proposed treatment system can be an economical solution.     

Nitrogen removal from sludge reject water by a two-stage oxygen-limited autotrophic nitrification denitrification process.

Nitrogen removal from sludge reject water was obtained by oxygen-limited partial nitritation resulting in nitrite accumulation in a first stage, followed by autotrophic denitrification of nitrite with ammonium as electron donor (similar to anaerobic ammonium oxidation) in a second stage. Two membrane-assisted bioreactors (MBRs) were used in series to operate with high sludge ages and subsequent high volumetric loading rates, achieving 1.45 kg N m(-3) day(-1) for the partial nitritation MBR and 1.1 kg N m(-3) day(-1) for the anaerobic ammonium oxidation MBR. Biomass retention in the nitritation stage ensured flexibility towards loading rate and operating temperature. Nitrite oxidisers were out-competed at low oxygen and high free ammonia concentration. Biomass retention in the second MBR prevented wash-out of the slowly growing bacteria. Nitrite and ammonium were converted to dinitrogen gas in a reaction ratio of 1.05, thereby maintaining nitrite limitation to assure process stability. The anoxic consortium catalysing the autotrophic denitrification process consisted of Nitrosomonas-like aerobic ammonium oxidizers and anaerobic ammonium oxidizing bacteria closely related to Kuenenia stuttgartiensis. The overall removal efficiency of the combined process was 82% of the incoming ammonium according to a total nitrogen removal rate of 0.55 kg N m(-3) day(-1), without adding extra carbon source.