Effect of density variation and non-covalent functionalization on the compressive behavior of carbon nanotube arrays

Arrays of aligned carbon nanotubes (CNTs) have been proposed for different applications, including electrochemical energy storage and shock-absorbing materials. Understanding their mechanical response, in relation to their structural characteristics, is important for tailoring the synthesis method to the different operational conditions of the material. In this paper, we grow vertically aligned CNT arrays using a thermal chemical vapor deposition system, and we study the effects of precursor flow on the structural and mechanical properties of the CNT arrays. We show that the CNT growth process is inhomogeneous along the direction of the precursor flow, resulting in varying bulk density at different points on the growth substrate. We also study the effects of non-covalent functionalization of the CNTs after growth, using surfactant and nanoparticles, to vary the effective bulk density and structural arrangement of the arrays. We find that the stiffness and peak stress of the materials increase approximately linearly with increasing bulk density.     

Highly oriented carbon nanotube papers made of aligned carbon nanotubes

Paper-like carbon nanotube (CNT) materials have many important applications such as in catalysts, in filtration, actuators, capacitor or battery electrodes, and so on. Up to now, the most popular way of preparing buckypapers has involved the procedures of dispersion and filtration of a suspension of CNTs. In this work, we present a simple and effective macroscopic manipulation of aligned CNT arrays called 'domino pushing' in the preparation of the aligned thick buckypapers with large areas. This simple method can efficiently ensure that most of the CNTs are well aligned tightly in the buckypaper. The initial measurements indicate that these buckypapers have better performance on thermal and electrical conductance. These buckypapers with controllable structure also have many potential applications, including supercapacitor electrodes.     

Synthesis and characterization of vertically aligned carbon nanotube forest for solid state fiber spinning

Continuous carbon nanotubes (CNT) fibers were directly spun from a vertically aligned CNT forest grown by a plasma-enhanced chemical vapor deposition (PECVD) process. The correlation of the CNT structure with Fe catalyst coarsening, reaction time, and the CNTs bundling phenomenon was investigated. We controlled the diameters and walls of the CNTs and minimized the amorphous carbon deposition on the CNTs for favorable bundling and spinning of the CNT fibers. The CNT fibers were fabricated with an as-grown vertically aligned CNT forest by a PECVD process using nanocatalyst an Al2O3 buffer layer, followed by a dry spinning process. Well-aligned CNT fibers were successfully manufactured using a dry spinning process and a surface tension-based densification process by ethanol. The mechanical properties were characterized for the CNT fibers spun from different lengths of a vertically aligned CNT forest. Highly oriented CNT fibers from the dry spinning process were characterized with high strength, high modulus, and high electrical as well as thermal conductivities for possible application as ultralight, highly strong structural materials. Examples of structural materials include space elevator cables, artificial muscle, and armor material, while multifunctional materials include E-textile, touch panels, biosensors, and super capacitors.     

Macroscopic carbon nanotube assemblies: preparation, properties, and potential applications

As classical 1D nanoscale structures, carbon nanotubes (CNTs) possess remarkable mechanical, electrical, thermal, and optical properties. In the past several years, considerable attention has been paid to the use of CNTs as building blocks for novel high-performance materials. In this way, the production of macroscopic architectures based on assembled CNTs with controlled orientation and configurations is an important step towards their application. So far, various forms of macroscale CNT assemblies have been produced, such as 1D CNT fibers, 2D CNT films/sheets, and 3D aligned CNT arrays or foams. These macroarchitectures, depending on the manner in which they are assembled, display a variety of fascinating features that cannot be achieved using conventional materials. This review provides an overview of various macroscopic CNT assemblies, with a focus on their preparation and mechanical properties as well as their potential applications in practical fields.     

Growth control of carbon nanotubes by plasma enhanced chemical vapor deposition

Plasma enhanced chemical vapor deposition (PECVD), which enables growth of vertically aligned carbon nanotubes (CNTs) directly onto a solid substrate, is considered to be a suitable method for preparing CNTs for nanoelectronics applications such as electron sources for field emission displays (FEDs). For these purposes, establishment of an efficient CNT growth process has been required. We have examined growth characteristics of CNTs using a radio frequency PECVD (RF-PECVD) method with the intention to develop a high efficiency process for CNT growth at a low enough temperature suitable for nanoelectronics applications. Here we report an effect of pretreatment of the catalyst thin film that plays an important role in CNT growth using RF-PECVD. Results of this study show that uniform formation of fine catalyst nanoparticles on the substrate is important for the efficient CNT growth.     

Controlled partial embedding of carbon nanotubes within flexible transparent layers

Applications of carbon nanotubes (CNTs) like field emission displays, super-capacitors, and cell growth scaffolds can benefit from controllable embedding of the CNTs in a material such that the CNTs are anchored and protrude a desired length. We demonstrate a simple method for anchoring densely packed, vertically aligned arrays of CNTs into silicone layers using spin-coating, CNT insertion, curing, and growth substrate removal. CNT arrays of 51 and 120?μm in height are anchored into silicone layers of thickness 26 and 36?μm, respectively. Scanning electron microscopy (SEM) and optical microscopy are used to characterize the sample morphology, a 5.5?m?s(-1) impinging water jet is used to apply shear stress, and a tensile test shows that the silicone layer detaches from the substrate before the CNTs are ripped from the layer. The CNTs are thus well anchored in the silicone layers. The spin-coating process gives control over layer thickness, and the method should have general applicability to various nanostructures and anchoring materials.     

Thermal Conductivity Behavior of Carbon Nanotubes Reinforced Copper Matrix Composites

Carbon nanotubes (CNT) exhibit excellent thermal conductivity.Therefore they are potential reinforcements in composites materials for thermal management applications,where high thermal conductivity and low coefficient of thermal expansion (CTE) are required.In the present study,CNT/Cu composites containing CNTs varying from 0 vol.％ to 15 vol.％ were prepared,and their thermal conductivity behavior was studied in detail.The results indicated that the thermal conductivity of the composites shows no enhancement by the incorporation of CNTs.The presence of interfacial thermal resistance and high level of porosity are the main reasons for this low thermal conductivity.The well dispersed 0-10 vol.％ CNTs composites show a very close to the thermal conductivity of Cu.However,the addition of 15 vol.％ CNTs results in a rather low thermal conductivity of CNT/Cu composites due to the presence a high level of porosity induced by the formation of CNT clusters.The present paper also claims that a further substantial enhancement in thermal conductivity is only possible if the nanotubes are randomly oriented in the plane or if they are all aligned in one direction,for which the processing of CNTs-aligning in metal matrix should be developed.     

Hydrothermal Coating of Patterned Carbon Nanotube Forest for Structured Lithium‐Ion Battery Electrodes

Controlling the arrangement and interface of nanoparticles is essential to achieve good transfer of charge, heat, or mechanical load. This is particularly challenging in systems requiring hybrid nanoparticle mixtures such as combinations of organic and inorganic materials. This work presents a process to coat vertically aligned carbon nanotube (CNT) forests with metal oxide nanoparticles using microwave‐assisted hydrothermal synthesis. Hydrothermal processes normally damage delicate CNT forests, which is addressed here by a combination of lithographic patterning, transfer printing, and reduction of the synthesis time. This process is applied for the fabrication of structured Li‐ion battery (LIB) electrodes where the aligned CNTs provide a straight electron transport path through the electrode and the hydrothermal coating process is used to coat the CNTs with conversion anode materials for LIBs. These nanoparticles are anchored on the surface of the CNTs and batteries fabricated following this process show a fourfold longer cyclability. Finally, this process is used to create thick electrodes (350 µm) with a gravimetric capacity of over 900 mAh g^?1.     

取向碳纳米管膜/氰基树脂复合材料的制备与性能强化机制

以浮动催化化学气相沉积法(FCCVD)碳纳米管(CNT)膜为原料,通过氰基树脂溶液浸渍法制备CNT预浸膜,然后采用热辅助牵伸和热压固化的方法制备高取向CNT膜复合材料。详细分析了热处理的温度和树脂溶液浓度对CNT预浸膜拉伸性能的影响,从而得到合适的热辅助牵伸工艺,并考察固化工艺对复合材料性能的影响。在此基础上,从浸润特性、CNT取向程度和层间剪切性能方面揭示CNT膜复合材料力学性能的强化机制。结果表明与传统CNT膜牵伸工艺相比,CNT预浸膜热牵伸工艺更有利于制备高取向CNT膜复合材料。热牵伸的温度和树脂溶液的浓度是制备高取向、低孔隙CNT预浸膜的关键因素。通过固化工艺的改变可有效调控氰基树脂的反应程度碳纳米管薄膜/氰基树脂复合材料的拉伸性能。经高温后固化处理后,CNT膜/氰基树脂复合材料的拉伸强度和模量分别高达2 748 MPa和302GPa。优异的树脂浸润特性、层间剪切强度以及高的CNT取向度使CNT膜复合材料中CNT更有利于协同承载,从而提高其力学性能。     

Manufacturing polymer/carbon nanotube composite using a novel direct process

A direct process for manufacturing polymer carbon nanotube (CNT)-based composite yarns is reported. The new approach is based on a modified dry spinning method of CNT yarn and gives a high alignment of the CNT bundle structure in yarns. The aligned CNT structure was combined with a polymer resin and, after being stressed through the spinning process, the resin was cured and polymerized, with the CNT structure acting as reinforcement in the composite. Thus the present method obviates the need for special and complex treatments to align and disperse CNTs in a polymer matrix. The new process allows us to produce a polymer/CNT composite with properties that may satisfy various engineering specifications. The structure of the yarn was investigated using scanning electron microscopy coupled with a focused-ion-beam system. The tensile behavior was characterized using a dynamic mechanical analyzer. Fourier transform infrared spectrometry was also used to chemically analyze the presence of polymer on the composites. The process allows development of polymer/CNT-based composites with different mechanical properties suitable for a range of applications by using various resins.     

Maximum nanotube volume fraction and its effect on overall elastic properties of nanotube-reinforced composites

The potential capability of improving overall elastic modulus of nanotube-reinforced composites is a fundamental concern in nanotechnology applications. Based on geometric analysis and micromechanics estimation, this study reports that the ratio of surface-to-surface distance of adjacent carbon nanotubes (CNTs) to the CNT diameter plays a key role in improving the overall elastic modulus of the CNT-reinforced composites when the tubes are perfectly aligned, completely separated from other tubes, and ideally bonded with the composite matrix. With the decrease of this ratio, that is, decrease of the surface-to-surface distance of adjacent CNTs and/or increase CNT diameter, the improvement capability increases. However, theoretical and experimental results show that an increase of the CNT diameters degrades the elastic moduli of CNTs. This paper discusses the criterion of choosing CNTs with larger diameter and addresses the factors influencing the surface-to-surface distance of adjacent CNTs.     

Flow-dependent directional growth of carbon nanotube forests by chemical vapor deposition

We demonstrated that the structural formation of vertically aligned carbon nanotube (CNT) forests is primarily affected by the geometry-related gas flow, leading to the change of growth directions during the chemical vapor deposition (CVD) process. By varying the growing time, flow rate, and direction of the carrier gas, the structures and the formation mechanisms of the vertically aligned CNT forests were carefully investigated. The growth directions of CNTs are found to be highly dependent on the nonlinear local gas flows induced by microchannels. The angle of growth significantly changes with increasing gas flows perpendicular to the microchannel, while the parallel gas flow shows almost no effect. A computational fluid dynamics (CFD) model was employed to explain the flow-dependent growth of CNT forests, revealing that the variation of the local pressure induced by microchannels is an important parameter determining the directionality of the CNT growth. We expect that the present method and analyses would provide useful information to control the micro- and macrostructures of vertically aligned CNTs for various structural/electrical applications.     

Preparation and properties of composites with staggered alignment of carbon nanotubes induced by electric field

In this paper, bulk polymeric composites with staggered orientation of carbon nanotubes (CNTs) in polymer matrix were prepared by means of a macro layer-by-layer (MLBL) method, while an alternating current (AC) electric field was applied for inducing alignment of the CNTs. Test results verified that there existed a relationship between conductive capacity of the composites and orientation of the CNTs in matrix. Conductivity of the composites containing aligned CNTs represented a dependency on time and testing history on the composite specimens. Among the composites with different orientation types of CNTs in the matrices, the composite specimens including staggered orientation of CNTs in polymer matrix demonstrated the most outstanding electric conductivity and showed similar conductive properties in the two directions of the CNT alignment.     

Formation and mechanical characterisation of SU8 composite films reinforced with horizontally aligned and high volume fraction CNTs

Carbon nanotube (CNT) reinforced composites have been identified as promising structural materials for the mechanical components of microelectromechanical systems (MEMS), potentially leading to advanced performance. High alignment and volume fraction of CNTs in the composites are the prerequisites to achieve such desirable mechanical characteristics. In particular, horizontal CNT alignment in composite films is necessary to enable high longitudinal moduli of the composites which is crucial for the performance of microactuators. A practical process has been developed to transfer CNT arrays from vertical to horizontal alignment which is followed by in situ wetting, realign and pressurized consolidation processes, which lead to a high CNT volume fraction in the range of 46-63%. As a result, SU8 epoxy composite films reinforced with horizontally aligned CNTs and a high volume faction of CNTs have been achieved with outstanding mechanical characteristics. The transverse modulus of the composite films has been characterised through nanoindentation and the longitudinal elastic modulus has been investigated. An experimental transverse modulus of 9.6 GPa and an inferred longitudinal modulus in the range of 460-630 GPa have been achieved, which demonstrate effective CNT reinforcement in the SU8 matrix.     

Microstructures and tensile behavior of carbon nanotube reinforced Cu matrix nanocomposites

Carbon nanotubes (CNTs) have been considered as an ideal reinforcement to improve the mechanical performance of monolithic materials. However, the CNT/metal nanocomposites have shown lower strength than expected. In this study, the CNT reinforced Cu matrix nanocomposites were fabricated by spark plasma sintering (SPS) of high energy ball-milled nano-sized Cu powders with multi-wall CNTs, and followed by cold rolling process. The microstructure of CNT/Cu nanocomposites consists of two regions including CNT/Cu composite region, where most CNTs are distributed, and CNT free Cu matrix region. The stress–strain curves of CNT/Cu nanocomposites show a two-step yielding behavior, which is caused from the microstructural characteristics consisting of two regions and the load transfer between these regions. The CNT/Cu nanocomposites show a tensile strength of 281 MPa, which is approximately 1.6 times higher than that of monolithic Cu. It is confirmed that the key issue to enhance the strength of CNT/metal nanocomposite is homogeneous distribution of CNTs.     

Flexible High‐Conductivity Carbon‐Nanotube Interconnects Made by Rolling and Printing

Applications of carbon nanotubes (CNTs) in flexible and complementary metal‐oxide‐semiconductor (CMOS)‐based electronic and energy devices are impeded due to typically low CNT areal densities, growth temperatures that are incompatible with device substrates, and challenges in large‐area alignment and interconnection. A scalable method for continuous fabrication and transfer printing of dense horizontally aligned CNT (HA‐CNT) ribbon interconnects is presented. The process combines vertically aligned CNT (VA‐CNT) growth by thermal chemical vapor deposition, a novel mechanical rolling process to transform the VA‐CNTs to HA‐CNTs, and adhesion‐controlled transfer printing without needing a carrier film. The rolling force determines the HA‐CNT packing fraction and the HA‐CNTs are processed by conventional lithography. An electrical resistivity of 2 mΩ · cm is measured for ribbons having 800‐nm thickness, while the resistivity of copper is 100 times lower, a value that exceeds most CNT assemblies made to date, and significant improvements can be made in CNT structural quality. This rolling and printing process could be scaled to full wafer areas and more complex architectures such as continuous CNT sheets and multidirectional patterns could be achieved by straightforward design of the CNT growth process and/or multiple rolling and printing sequences.     

Systematic study of thermal properties of CNT composites by the fast multipole hybrid boundary node method

Carbon nanotubes (CNTs) are predicted to possess superior heat conductivity, which makes the CNTs promising in development of fundamentally new composite material. With the current advancement in nanotechnology, it is possible to design materials with desired properties for specific applications. On the other hand, the overall properties of CNT composites are usually evaluated using a representative volume element (RVE) with a number of CNTs embedded. For realistic modeling, an RVE including a large number of CNTs, for example, tens or hundreds, is necessary. However, analysis of such an RVE using standard numerical methods faces two severe difficulties: discretization of the geometry into elements and the very large computational scale. In this paper, the first difficulty is alleviated by developing the hybrid boundary node method (HdBNM), which is a boundary-type meshless method. To overcome the second difficulty, a simplified mathematical model for thermal analysis of CNT analysis is first proposed, by which the size of the linear system can be reduced by nearly half. Then, the HdBNM is combined with the Fast Multipole Method (FMM) based on the model to further reduce the computational scale. A variety of RVEs containing different numbers of CNTs, from small to large scales, have been studied in an attempt to investigate the influence of CNT length, distribution, orientation and volume fraction on the overall thermal properties of the composites. Insights have been gained into the thermal behavior of the CNT composite material.     

Properties of composites of carbon nanotube fibres

Composites have set the standard for high strength materials for several decades. With the discovery of nanotubes, new possibilities for reinforced composites have arisen, with potential mechanical properties superior to those of currently available materials. This paper reports the properties of epoxy matrix reinforced with fibres of carbon nanotubes (CNTs) which, in many ways, are similar to standard composites reinforced with commercial fibres. The composites were formed by the back diffusion of the uncured epoxy into an array of aligned fibres of CNTs. The fibre density and volume fraction were measured from thermogravimetric analysis (TGA). Properties in tension and compression were measured, and the level of fibre–matrix interaction analysed fractographically. The results show the significant potential for this route to CNT reinforcement.     

Growth of horizontally aligned dense carbon nanotubes from trench sidewalls

Horizontally aligned, dense carbon nanotubes (HADCNTs) in the form of CNT cantilevers/bridges were grown from selected trench sidewalls in silicon substrate by chemical vapor deposition (CVD). The as-grown CNT cantilevers/bridges are packed with multiwalled carbon nanotubes (MWCNTs) with a linear density of about 10 CNTs μm(-1). The excellent horizontal alignment of these CNTs is mainly ascribed to the van der Waals interactions within the dense CNT bundles. What is more, the Raman intensity ratio I(G)/I(D) shows a gradual increase from the CNT roots to tips, indicating a defect gradient along CNTs generated during their growth. These results will inspire further efforts to explore the fundamentals and applications of HADCNTs.     

Turning refuse plastic into multi-walled carbon nanotube forest

Abstract

A novel and effective method was devised for synthesizing a vertically aligned carbon nanotube (CNT) forest on a substrate using waste plastic obtained from commercially available water bottles. The advantages of the proposed method are the speed of processing and the use of waste as a raw material. A mechanism for the CNT growth was also proposed. The growth rate of the CNT forest was ～2.5 μm min^?1. Transmission electron microscopy images indicated that the outer diameters of the CNTs were 20–30 nm on average. The intensity ratio of the G and D Raman bands was 1.27 for the vertically aligned CNT forest. The Raman spectrum showed that the wall graphitization of the CNTs, synthesized via the proposed method was slightly higher than that of commercially available multi-walled carbon nanotubes (MWCNTs). We expect that the proposed method can be easily adapted to the disposal of other refuse materials and applied to MWCNT production industries.