A novel design of a cpw‐fed single square‐loop antenna for circular polarization

Abstract

The experimental and simulated results for the proposed antenna are investigated in this article. Moreover, a novel broadband design of a circularly polarized (CP) single square slot antenna fed by a single coplanar waveguide is presented. By appropriately choosing the circumference of the square‐loop, the length of the protruded strip, and the gap, this proposed antenna thus owns good CP radiation and good impedance match simultaneously at the frequency of 2.45 GHz. This proposed antenna has the fundamental resonant frequency of 2.5 GHz with the minimum return loss of ‐39.9 dB. Furthermore, its impedance bandwidth is 460 MHz or 18.4% and 3‐dB axial‐ratio (AR) bandwidth is 360 MHz or 14.4% at 2.5 GHz.     

Reconfigurable Compact Wideband Circularly Polarised Dielectric Resonator Antenna for Wireless Applications

In this work, a novel compact wideband reconfigurable circularly polarised (CP) dielectric resonator antenna (DRA) is presented. The L-shaped Dielectric resonator antenna is excited by an inverted question mark shaped feed. This arrangement of feed-line helps to generate two orthogonal modes inside the DR, which makes the design circularly polarised. A thin micro-strip line placed on the defected ground plane not only helps to generate a wideband response but also assist in the positioning of the two diode switches. These switches located at the left and right of the micro-strip line helps in performing two switching operations. The novel compact design offers the reconfigurability between 2.9–3.8 GHz which can be used for different important wireless applications. For the switching operation I, the achieved impedance bandwidth is 24% while axial ratio bandwidth (ARBW) is 42%. For this switching state, the design has 100% CP performance. Similarly, the switching operation II achieves 60% impedance bandwidth and 58.88% ARBW with 76.36% CP performance. The proposed design has a maximum measured gain of 3.4 dBi and 93% radiation efficiency. The proposed design is novel in terms of compactness and performance parameters. The prototype is fabricated for the performance analysis which shows that the simulated and measured results are in close agreement.     

Inkjet Printed Metamaterial Loaded Antenna for WLAN/WiMAX Applications

In this paper, the design and performance analysis of an Inkjet-printed metamaterial loaded monopole antenna is presented for wireless local area network (WLAN) and worldwide interoperability for microwave access (WiMAX) applications. The proposed metamaterial structure consists of two layers, one is rectangular tuning fork-shaped antenna, and another layer is an inkjet-printed metamaterial superstate. The metamaterial layer is designed using four split-ring resonators (SRR) with an H-shaped inner structure to achieve negative-index metamaterial properties. The metamaterial structure is fabricated on low-cost photo paper substrate material using a conductive ink-based inkjet printing technique, which achieved dual negative refractive index bands of 2.25–4.25 GHz and 4.3–4.6 GHz. The antenna is designed using a rectangular tuning fork structure to operate at WLAN and WiMAX bands. The antenna is printed on 30 × 39 × 1.27 mm3 Rogers RO3010 substrate, which shows wide impedance bandwidth of 0.75 GHz (2.2 to 2.95 GHz) with 2 dB realized gain at 2.4 GHz. After integrating metamaterial structure, the impedance bandwidth becomes 1.25 GHz (2.33 to 3.58 GHz) with 2.6 dB realized gain at 2.4 GHz. The antenna bandwidth and gain have been increased using developed quad SRR based metasurface by 500 MHz and 0.6 dBi respectively. Moreover, the proposed quad SRR loaded antenna can be used for 2.4 GHz WLAN bands and 2.5 GHz WiMAX applications. The contribution of this work is to develop a cost-effective inject printed metamaterial to enhance the impedance bandwidth and realized the gain of a WLAN/WiMAX antenna.     

Broadband flexible comb-shaped monopole antenna

A broadband comb-shaped monopole antenna is proposed. The antenna has dimensions of 19 mm x 12 mm. The measured results show good agreement with the numerical prediction, and broadband operation with 10 dB impedance bandwidth of 44.75% (1.7-2.68 GHz). The antenna is built on one side of a flexible-printed circuit board (PCB) dielectric substrate. Folded and rolled antenna structures, which are transformed by the proposed planar antenna structure, are presented. Each antenna has a broadband impedance bandwidth that covers the PCS, UMTS, WiBro, WLAN and SDMB bands. Also, omni-directional radiation patterns over the operating bands have been obtained. The proposed antennas are suitable for mobile communication applications requiring a small antenna.     

Triple-frequency meandered monopole antenna with shorted parasitic strips for wireless application

The performance of a triple-frequency meandered-strip monopole antenna for wireless application is presented. The proposed antenna comprises of a microstrip-fed monopole with an additional meandered strip and a ground plane with three protrudent strips on the opposite side of the substrate. By adding these shorted parasitic strips to this monopole, good impedance matching for multi-band application is obtained. Tuning effects of the additional shorted strips to the different resonant modes were examined and prototype of the proposed antenna had been constructed and experimentally studied. The measured results explore a broadband triple-frequency operation covering the required bandwidths of the PCS-1900/UMTS-2100 and the 2.4/5.2/5.8 GHz WLAN standards, a near-directive radiation pattern and a good antenna gain for this design.     

Wideband microstrip antennas with sandwich substrate

A broadband microstrip antenna with low?high?low (sandwich) dielectric constant substrate combination using a microstrip line-via feed is presented for ultra-wideband applications. The proposed antenna consists of three dielectric substrates; low dielectric constant substrates that contain the microstrip feed line as well as parasitic patches and a high dielectric constant substrate that contains the driven patch. To achieve a large impedance bandwidth, parasitic patches and microstrip line-via combination feed to the driven patch in the multilayered microstrip antenna are used. The proposed antenna designed, fabricated and measured on the sandwich substrate. The antenna has measured 10 dB return loss bandwidth of 46.9% and directive gain .5.2 dBi at boresight across the impedance bandwidth. The total height of antenna is 5.77 mm or 0.077λ ^{at 4 GHz.}     

A Novel Compact Highly Isolated UWB MIMO Antenna with WLAN Notch

This paper presents a compact Multiple Input Multiple Output (MIMO) antenna with WLAN band notch for Ultra-Wideband (UWB) applications. The antenna is designed on 0.8 mm thick low-cost FR-4 substrate having a compact size of 22 mm × 30 mm. The proposed antenna comprises of two monopole patches on the top layer of substrate while having a shared ground on its bottom layer. The mutual coupling between adjacent patches has been reduced by using a novel stub with shared ground structure. The stub consists of complementary rectangular slots that disturb the surface current direction and thus result in reducing mutual coupling between two ports. A slot is etched in the radiating patch for WLAN band notch. The slot is used to suppress frequencies ranging from 5.1 to 5.9 GHz. The results show that the proposed antenna has a very good impedance bandwidth of |S11| < −10 dB within the frequency band from 3.1–14 GHz. A low mutual coupling of less than −23 dB is achieved within the entire UWB band. Furthermore, the antenna has a peak gain of 5.8 dB, low ECC < 0.002 and high Diversity Gain (DG > 9.98).     

Aperture-coupled asymmetrical c-shaped slot microstrip antenna for circular polarisation

A novel aperture-coupled, asymmetrical C-shaped slot, square microstrip antenna is proposed for circular polarisation (CP). A narrow and asymmetrical C-shaped slot, microstrip antenna is fed at the centre using an aperture coupling to obtain a CP operation. The compactness of the antenna is easily obtained by inserting a C-shaped slot. Wide CP radiation is achieved simply by making the C-shaped slot asymmetrical. With this antenna, the measured 3 dB AR bandwidth is around 3.3% and the 10 dB return loss bandwidth achieved is 16.0%. The overall antenna size is 0.48λo x 0.48λo x 0.092λo at 2.4 GHz. The proposed slot microstrip patch technology is useful to design compact, broadband, circularly polarised antennas and arrays.     

Internal triple-band folded planar antenna design for third generation mobile handsets

A novel internal triple-band folded planar antenna for mobile handsets is introduced, formed by modifying the geometry of a rectangular patch antenna to include a shorting pin, folded sides, a shorted microstrip stub and a notch. The size of the antenna is successfully reduced to a volume of 34 times 34 times 7 times mm³. The antenna is mounted on a finite ground plane of 50times100 times mm². The impedance bandwidth achieved was 29.7% (equivalent to return loss%%10%dB); this covers the DCS1800, PCS1900 and UMTS 2000 bands. The characteristics of the proposed antenna, including impedance bandwidth and far field radiation patterns are discussed theoretically and experimentally; the simulated and measured results show good agreement. The tuning effects of the geometry parameters on impedance matching of the proposed antenna are also investigated.     

Super Compact UWB Monopole Antenna for Small IoT Devices

This article introduces a novel, ultrawideband (UWB) planar monopole antenna printed on Roger RT/5880 substrate in a compact size for small Internet of Things (IoT) applications. The total electrical dimensions of the proposed compact UWB antenna are 0.19 λ_o × 0.215 λ_o × 0.0196 λ_o with the overall physical sizes of 15 mm × 17 mm × 1.548 mm at the lower resonance frequency of 3.8 GHz. The planar monopole antenna is fed through the linearly tapered microstrip line on a partially structured ground plane to achieve optimum impedance matching for UWB operation. The proposed compact UWB antenna has an operation bandwidth of 9.53 GHz from 3.026 GHz up to 12.556 GHz at −10 dB return loss with a fractional bandwidth (FBW) of about 122%. The numerically computed and experimentally measured results agree well in between. A detailed time-domain analysis is additionally accomplished to verify the radiation efficiency of the proposed antenna design for the ultra-wideband signal propagation. The fabricated prototype of a compact UWB antenna exhibits an omnidirectional radiation pattern with the low peak measured gain required of 2.55 dBi at 10 GHz and promising radiation efficiency of 90%. The proposed compact planar antenna has technical potential to be utilized in UWB and IoT applications.     

Wideband multilayered microstrip antennas fed by coplanar waveguide-loop with and without via combinations

Coplanar waveguide (CPW)-loop fed wideband multilayered microstrip antennas with and without via combinations are presented. The antenna consists of two dielectric substrates, CPW-loop on the ground plane layer, main patch on the middle layer and four asymmetric parasitic patches on the upper layer. The feed consists of a CPW, a loop on a ground plane and a via between main patch and feeding strip on the ground plane layer. Using via, the gain flatness over the impedance bandwidth and return loss are improved. The proposed antenna with four feeding structures is also studied. The 10 dB return loss bandwidths of the antenna with and without via are 34% (3.12? 4.41 GHz) and 33.7% (3.18 ?4.47 GHz), respectively. The measured gain is >5.0 dBi over the impedance bandwidth.     

一种改善超宽带MIMO天线隔离性能的方法

多输入多输出(Multiple-InputMultiple-Output,MIMO)技术是现代通信技术的发展趋势,为移动通信的迅速更迭提供了极大支持.设计了一种二端口的超宽带MIMO天线,其-10 dB阻抗带宽从3.3 GHz扩展到9.1 GHz.通过在天线接地板上蚀刻一条宽缝隙,并在其中添加音叉型枝节,改善了超宽带M...     

A Novel Broadband Microstrip Antenna Based on Operation of Multi-Resonant Modes

A novel broadband microstrip antenna under operation of TM_1/2,0, TM₁₀ and TM₁₂ modes through a shorting wall and slots is proposed in this paper. Initially, an inverted U-shaped slot is adopted around the feeding point, which achieves a good impedance matching on TM₁₀ mode and separates the patch into two parts. Additionally, a shorting wall is added underneath the edge of smaller patch to excite another one-quarter resonant mode, i.e., TM_1/2,0 mode of smaller patch close to TM₁₀ mode to expand the impedance bandwidth. Further, the antenna width is enlarged and two symmetrical vertical rectangular slots are cut on the patch to reduce the frequency of TM₁₂ mode to form a broadband. Based on the arrangements above, a wide impedance bandwidth with three minima can finally be achieved. The results show that the impedance bandwidth of proposed antenna for |S11|<-10 dB is extended to 26.5% (23.5-30.67 GHz), which is three times of the conventional antenna at same profile. Moreover, a stable radiation pattern at broadside direction is realized over the operating band.     

A Compact Flexible Circularly Polarized Implantable Antenna forBiotelemetry Applications

With the help of in-body antennas, the wireless communication among the implantable medical devices (IMDs) and exterior monitoring equipment, the telemetry system has brought us many benefits. Thus, a very thin-profile circularly polarized (CP) in-body antenna, functioning in ISM band at 2.45 GHz, is proposed. A tapered coplanar waveguide (CPW) method is used to excite the antenna. The radiator contains a pentagonal shape with five horizontal slits inside to obtain a circular polarization behavior. A bendable Roger Duroid RT5880 material (ε_r = 2.2, tanδ = 0.0009) with a typical 0.25 mm-thickness is used as a substrate. The proposed antenna has a total volume of 21 × 13 × 0.25 mm³. The antenna covers up a bandwidth of 2.38 to 2.53 GHz (150 MHz) in vacuum, while in skin tissue it covers 1.56 to 2.72 GHz (1.16 GHz) and in the muscle tissue covers 2.16 to 3.17 GHz (1.01 GHz). GHz). The flexion analysis in the x and y axes was also performed in simulation as the proposed antenna works with a wider bandwidth in the skin and muscle tissue. The simulation and the curved antenna measurements turned out to be in good agreement. The impedance bandwidth of −10 dB and the axis ratio bandwidth of 3 dB (AR) are measured on the skin and imitative gel of the pig at 27.78% and 35.5%, 13.5% and 4.9%, respectively, at a frequency of 2.45 GHz. The simulations revealed that the specific absorption rate (SAR) in the skin is 0.634 and 0.914 W/kg in muscle on 1g-tissue. The recommended SAR values are below the limits set by the federal communications commission (FCC). Finally, the proposed low-profile implantable antenna has achieved very compact size, flexibility, lower SAR values, high gain, higher impedance and axis ratio bandwidths in the skin and muscle tissues of the human body. This antenna is smaller in size and a good applicant for application in medical implants.     

Compact wideband multi-layer cylindrical dielectric resonator antennas

Homogenous dielectric resonator antennas (DRAs) have been studied widely and their bandwidth have been reached to the possible upper limit. A new non-homogenous DRA, multilayer cylindrical DRA (MCDRA), is designed and fabricated to achieve wider bandwidth. The antennas consist of three different dielectric discs, one on top of the other. Two different excitation mechanisms are studied here. As much as 66% of impedance bandwidth with a broadside radiation pattern has been demonstrated using a 50 Omega coaxial probe placed off the antenna axis. More than 32% of impedance with a broadside radiation pattern has been achieved when the antenna is excited by an aperture coupled 50 Omega microstrip feedline. Mode analysis is carried out to investigate the natural resonance behaviours of the MCDRA structure.     

Compact active integrated microstrip antennas with circular polarisation diversity

A compact active integrated microstrip antenna with circular polarisation (CP) diversity for a global positioning system (GPS) receiver is presented. As a radiator, a diamond-shaped micro- strip ring patch with four embedded slots has been newly proposed to realise wide impedance bandwidth, compact size and dual CP. The active circuitry, consisting of both switching circuits and a small signal amplifier, is placed at the square opening inside the radiator. Thus, all electrical parts are mounted on the top layer of the circuit board. CP diversity is achieved by the switching circuit, and its output signal is amplified. The proposed antenna has been simulated and fabricated on the FR-4 PCB board. The size of the fabricated active antenna, including the radiator and active circuitry, is only about 57% of a conventional square-microstrip antenna with a side of half wavelength. From the measured radiation patterns and CP bandwidth for either polarisation selection, it is proven that this antenna has successfully performed the polarisation diversity. In addition, the measured minimum antenna gain of 12 dBi is estimated to be good enough to improve the GPS receiver performance.     

基于LTCC宽频带双频差分天线的研究与设计

提出了一种新型宽频带双频差分天线.该天线基于低温共烧陶瓷(Low Temperature Co-Fired Ceramies,简称LTCC)技术,采用矩形环状贴片,并使用两条叉形微带馈线进行差分馈电,是一种具有平衡结构的宽缝隙天线,该结构使得天线拥有很宽的频带宽度.天线两频段的中心频率为2.63 GHz和5.13 GH...     

Low profile wideband embedded dielectric resonator

A dielectric resonator antenna (DRA) made of high dielectric constant substrate is studied. Embedding a higher dielectric disk inside the substrate disk enhances the bandwidth. A narrow slot excites the DRA. Embedded DRAs of different shapes are considered for wideband applications. An eye-shaped DRA made with a circular dielectric resonator disk embedded in an elliptical-shaped `host' DRA is found to have an impedance bandwidth of 28% with stable broadside patterns     

Broadband designs of coplanar capacitivelyfed shorted patch antennas

The author presents a coplanar capacitively fed shorted patch antenna for easy fabrication and providing a very wide impedance bandwidth. In this design, a feeding strip is located on the same plane as that of the radiating patch and used to excite the antenna by electromagnetic coupling. Experimental results reveal that the impedance bandwidth of the proposed antenna depends not only on the length and location of the feeding strip but also on the width of the radiating patch. For the optimal result obtained in the design, the 10 dB return-loss impedance bandwidth is as large as 78%. The radiation characteristics of the operating frequencies within the obtained wide bandwidth are also studied and presented.     

Metamaterial superstrate-loaded meandered microstrip-based radiating structure for bandwidth enhancement

We have introduced metamaterial superstrate in microstrip-based radiating structure to increase its bandwidth. Split ring resonators are added as metamaterial metallic inclusion in superstrate of the conventional design. This changes the basic structure of the material. Material properties such as permittivity and permeability changed due to change in the structure. The change in its material properties enhances the bandwidth of the antenna. The antenna is meandered to achieve better performance at the edges which in a way improve the radiation path of the patch. Here, the proposed antenna works on three bands in the range 3–8?GHz. Maximum 60% bandwidth is enhanced in the third band. The voltage standing wave ratio and return loss (S₁₁) of the entire three bands are shown in the paper. The antenna works on 3.51, 4.86 and 7.8?GHz. Design results are obtained by high-frequency structure simulator which is used for simulating microwave passive components.