LDZ125微晶涂层抗循环氧化性能

研究了高温合金LDZ125及其溅射微晶涂层的抗循环氧化行为.微晶涂层仅由γ相组成,晶粒尺寸约为30nm.结果表明:微晶涂层在1000℃的抗循环氧化性能比铸态合金的有极大提高.微晶层氧化时只形成单一的Al2O3氧化膜,且在整个氧化过程中未见开裂剥落,有极好的粘附性.     

K17F高温合金溅射微晶层的抗循环氧化行为

用溅射方法获得了晶粒尺寸小于０．１μｍ的高温合金Ｋ１７Ｆ的微晶涂层，对铸态高温合金Ｋ１７Ｆ及其溅射微晶层的循环氧化行为进行了研究，结果表明，微晶层中含γ相，不含γ和碳化物相，为匀相组织。它在１０００℃的抗循环氧化性能较铸态合金有极大提高，溅射微晶层具有优异的防护性和粘附性，在冷却过程中不会开裂，即使在１００次循环氧化后仍未见剥落。     

高温合金涂层与基体界面上的互扩散

研究了高温合金上热扩散涂层、多元包覆涂层和微晶涂层与基体合金间的互扩散，以及扩散障层对阻碍扩散的作用。结果表明扩散渗铝涂层与基体间形成较宽的含碳化物的扩散带及含σ要的影响区；在多元包覆涂层与基体间形成以γ＿β相组成的扩散带；在微晶涂层与基体合金间无新相生成，仅γ′相会粗化。扩散障层对阻碍元素扩散有一定作用。     

高温合金微晶涂层上氧化膜的修复性

本文研究了一种镍基高温合金K38G的微晶涂层上保护性氧化膜的修复性。结果表明,溅射微晶涂层上的氧化膜有优良的修复性,氧化膜剥落后,涂层仍具有优良的抗高温氧化性能。氧化膜局部小范围剥落后,表面仍能生成单一的Al_2O_3,氧化膜。氧化膜大面积剥落后,虽然生成由(Al、Cr)_2O_3与TiO_2组成的复合外氧化膜,但它具有优良的防护性和粘附性。     

K38G合金及其溅射微晶层的高温氧化

研究了K38G铸造镍基高温合金及其用平面磁控离广溅射工艺制备的微晶涂层在800-1000℃500小时内的抗高温氧化性。结果表明,微晶化极大改善合金的抗氧化能力,并改变合金表面生成的氧化物类型,由Cr_2O_3变为α-Al_2O_3。还讨论了铸态K38G合金及溅射微晶层的氧化机理。     

K17F微晶涂层氧化膜的修复性

研究了高温合金Ｋ１７Ｆ溅射微晶涂层的氧化膜的修复性。     

Fe20Cr4.5Al微晶和含Y2O3弥散氧化物涂晶涂层的高温氧化性能

采用自行研制的高频电脉冲沉积（HFESD）设备在Fe20Cr4.5Al合金表面分别制备了Fe20Cr4.5Al微晶涂层与Fe20Cr4.5Al-Y2O3弥散氧化物微晶涂层。在1000℃和1100℃静态空气中，对合金基体和施加涂层试样进行了200h的恒温氧化实验。结果表明：在两种实验温度条件下，含有Y2O3弥散氧化物颗粒的微晶涂层，完全消除了Al2O3氧化膜中的凸脊，细化了氧化膜的晶粒，抑制了氧化膜的剥落，大大地提高了氧化膜的致密性和粘附性。单一的微晶涂层则部分抑制了凸脊状氧化膜的形成，氧化膜由脊状氧化物和细晶氧化物混杂组成。涂层对氧化增重的影响则与氧化温度－氧化膜的生长速率有关，在1000℃下，涂层试样的氧化增重均有所降低，其中弥散氧化物微晶涂层试样的氧化增重最低；在1100℃下，施加微晶涂层和弥散氧化物涂层对氧化增重影响很小。微晶和Y2O3弥散氧化物颗粒在提高Al2O3氧化膜保护性方面具有“协同效应”。     

Fe20Cr4.5Al微晶和含Y2O3弥散氧化物微晶涂层的高温氧化性能

采用自行研制的高频电脉冲沉积(HFESD)设备在Fe20Cr4.5Al合金表面分别制备了Fe20Cr4.5Al微晶涂层与Fe20Cr4.5Al-Y2O3弥散氧化物微晶涂层.在1000℃和1100℃静态空气中,对合金基体和施加涂层试样进行了200 h的恒温氧化实验.结果表明在两种实验温度条件下,含有Y2O3弥散氧化物颗粒的微晶涂层,完全消除了Al2O3氧化膜中的凸脊,细化了氧化膜的晶粒,抑制了氧化膜的剥落,大大地提高了氧化膜的致密性和粘附性.单一的微晶涂层则部分抑制了凸脊状氧化膜的形成,氧化膜由脊状氧化物和细晶氧化物混杂组成.涂层对氧化增重的影响则与氧化温度-氧化膜的生长速率有关,在1000℃下,涂层试样的氧化增重均有所降低,其中弥散氧化物微晶涂层试样的氧化增重最低;在1100℃下,施加微晶涂层和弥散氧化物涂层对氧化增重影响很小.微晶和Y2O3弥散氧化物颗粒在提高Al2O3氧化膜保护性方面具有"协同效应".     

梯度NiCrAlY涂层的1000和1100℃氧化行为研究

采用电弧离子镀技术及后续热处理工艺在镍基高温合金上制备了均匀NiCrAlY涂层和梯度NiCrAlY涂层,分析了2种涂层的组织结构,对比研究了2种涂层静态空气下1000和1100℃恒温氧化行为以及1100℃的循环氧化行为.结果表明:均匀NiCrAlY涂层由γ′/γ相和少量β-NiAl相、α-Cr相组成,成分分布均匀;梯度NiCrAlY涂层具有外层富Al和内层富Cr的结构,其中外层由β-NiAl相和少量γ′/γ相、α-Cr相组成.一方面,梯度涂层的初始Al含量较高;另一方面,氧化过程中其富Cr区两侧出现了对富Al区的Al向基体扩散起阻碍作用的Cr(W)析出带.这两方面使梯度涂层长时间维持更多的Al存储相,提升了氧化膜的迅速生成及再生成能力,从而使涂层具有较好的抗氧化性能.     

K17F高温合金溅射微晶层的抗高温氧化行为

研究了铸态高温合金Ｋ１７Ｆ及其溅射微晶（小于０．１μｍ）层的高温氧化行为。结果表明，微晶层均匀的γ相组织，它大幅度提高铸态合金的９００至１０００℃的抗氧化性能，甚至比渗Ａｌ涂层还好，在高温下，Ｋ１７Ｆ生成以Ａｌ２Ｏ３主为，含有Ｎｉ，Ｃｒ，Ｔｉ氧化物的氧化膜，它在氧化过程中易剥落，而溅射微晶层表面只生成单一的α－Ａｌ２Ｏ３膜，具有优异的防护性和粘附性，在５００ｈ的氧化过程中未见剥落。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.