Highly efficient, widely tunable, 10-Hz parametric amplifier pumped by frequency-doubled femtosecond Ti:sapphire laser pulses

We report a 10-Hz, highly efficient, widely tunable (from the visible to the IR), broadband femtosecond optical parametric generator and optical parametric amplifier (OPA) in BBO, LBO, and CBO crystals pumped by the frequency-doubled output of a regeneratively amplified Ti:sapphire laser at 400 nm. The output of the system is continuously tunable from 440 nm to 2.5 mum with a maximum overall efficiency of ~25% at 670 nm and an optical conversion efficiency of more than 36% in the OPA stage. The effects of the seed beam energy, the type of the crystal and the crystal length, and the pumping energy of the output of the OPA, such as the optical efficiency, the bandwidth, the pulse duration, and the group velocity mismatch between the signal and the idler and between the seeder and the pump, are investigated. The results provide useful information for optimization of the design of the system.     

Femtosecond Traveling-Wave Optical Parametric Amplification in MgO:LiNbO(3)

A mid-infrared femtosecond optical parametric amplifier tunable in the chemically important spectral region between 3.1 and 3.9 mum (at >10-muJ idler pulse energy) has been constructed on the basis of MgO:LiNbO(3) with 7% doping. With femtosecond pumping near 800 nm (Ti:sapphire regenerative amplifier) and narrow-band (long-pulse) seeding, this simple single-stage device provides maximum conversion efficiencies of 40% and exhibits extremely low seed threshold (<10-mW peak seed power for >1-muJ idler output). The generated idler pulses are almost transform limited with <200-fs pulse duration. The pulse-to-pulse fluctuations reproduce the stability of the pump source at 1-kHz repetition rate.     

Sum-Frequency Generation of Femtosecond Pulses in CsLiB(6)O(10) Down to 175 nm

Using a 150-mum-thick CsLiB(6)O(10) crystal, we produced 100-fs, >200-nJ light pulses tunable between 175 and 180 nm by sum-frequency generation at a 1-kHz repetition rate with an all-solid-state laser system mixing the fourth harmonic of a femtosecond Ti:sapphire regenerative amplifier and the idler pulse from a traveling-wave optical parametric amplifier.     

Tunable picosecond blue and ultraviolet pulses from a diode-pumped laser system seeded by a gain-switched laser diode

Picosecond pulses emitted from a gain-switched laser diode have been amplified in a Ti:sapphire regenerative amplifier indirectly pumped by a 4-W laser diode. This all-solid-state system produced microjoule pulses tunable from 803 to 840 nm at repetition rates up to 25 kHz with durations of 70-100 ps. By frequency doubling and tripling the output, we generated blue and UV pulses tunable from 401 to 420 nm and from 268 to 280 nm, respectively. Average powers larger than 4 mW were reached in these two wavelength regions.     

Compact 50-Hz terawatt Ti:sapphire laser for x-ray and nonlinear optical spectroscopy

We report a high-repetition-rate, compact terawatt Ti:sapphire laser system. The oscillator produces an 82-MHz pulse train consisting of broad-bandwidth pulses of 0.5-nJ/pulse energy and of 9-fs pulse duration. The spectrally shaped, lambda/4 regenerative amplifier supports an 80-nm bandwidth. A single 50-Hz repetition-rate pump laser pumps both the regenerative amplifier and a multiple-pass amplifier. The final output from this laser is a 50-Hz pulse train made from pulses of 53 mJ/pulse energy and of 24-fs pulse duration. For generating ultrafast x-ray pulses, 90% of the energy from the final output of a 28-mm-diameter (1/e2) beam is focused onto an ultrafast x-ray wire target. The energy conversion efficiency from optical (800-nm central wavelength) to x-ray (characteristic lines of K(alpha) from Cu at 8 keV) pulses is estimated to be 7 x 10(-5). This laser system can also generate a lower-peak-power, dual-pulse output that can excite, simultaneously and coherently, Raman modes within an adjustable bandwidth (up to 700 cm(-1)) and at a tunable central vibrational frequency. Preliminary results for the generation of dual-pulse output and ultrafast x rays are presented.     

Optical parametric amplification of femtosecond pulses tunable from the blue to the infrared with microjoule energies

A white-light continuum is used to seed a two-stage optical parametric amplifier pumped by the second harmonic of a regeneratively amplified Ti:sapphire laser system operating at 824 nm. Microjoule energies are achieved in the signal branch, which is tunable from 472 to 785 nm. Near-transform-limited sub-200-fs pulses are attainable over the vast majority of the tuning range.     

High-energy picosecond near-vacuum ultraviolet pulses generated by sum-frequency mixing of an amplified Ti:sapphire laser

We demonstrate high-energy picosecond near-vacuum ultraviolet laser pulse generation. Frequency quadrupling is achieved by noncollinear sum-frequency mixing of the fundamental and the third harmonic of a two-stage Ti:sapphire amplifier in beta-BaB(2)O(4) crystal. UV pulses with energies of approximately 10 mJ tunable from 195 to 210 nm at a 10 Hz repetition rate are obtained.     

Seeded femtosecond optical parametric amplification in the mid-infrared spectral region above 3 mum

Femtosecond optical parametric amplification that results in microjoule mid-infrared pulses at wavelengths exceeding 3 mum is demonstrated. Narrow-band quasi-cw seeding at the signal wavelength is applied to ensure the generation of nearly transform-limited femtosecond pulses at the idler wavelength. The broad bandwidth of the parametric amplification provided by pumping with femtosecond pulses from a Ti:sapphire regenerative amplifier at high intensity results in idler pulse durations shorter than the pump pulse length. The potentials of three nonlinear optical crystals that belong to the potassium titanyl phosphate family are comparatively studied. At 1-kHz repetition rate our all-solid-state system produces highly synchronized ~100-fs pulses in the spectral range between 3 and 4 mum.     

Short-pulse amplification at 745 nm in Ti:sapphire with a continuously tunable regenerative amplifier

We describe the design of a continuously tunable Ti:sapphire regenerative amplifier that is capable of sustaining amplification over a wavelength range from 730 nm to more than 800 nm. The amplifier cavity is tuned with a prism pair in combination with a spherical mirror. It sustains an oscillation bandwidth of 5 nm and produces a chirped output pulse energy of 1.2 mJ compressible to a duration of 140 fs at 745 nm. We present a calculation of the theoretical bandwidth.     

Visible optical parametric generator producing nearly bandwidth-limited femtosecond light pulses at 1-kHz repetition rate

The second harmonic of a femtosecond Ti:sapphire regenerative amplifier system is used to pump parametric generator-amplifier producing visible light pulses of 160-fs duration near 570 nm and infrared pulses of < 100-fs duration between 1.23 and 1.45 μm.     

Amplified spontaneous emission in a Ti:sapphire regenerative amplifier

Amplified spontaneous emission power and contrast ratio in a linear miltipass Ti:sapphire regenerative amplifier with a wavelength centered at 1054 nm are calculated and measured. It is shown that the passive losses of a seed pulse and the losses in coupling to the regenerative amplifier cavity mode degrade the intensity contrast ratio to 10(-6)-10(-7). The advantage of an optical parametric chirped pulse amplifier with respect to the contrast ratio is discussed.     

Infrared-ultraviolet sum-frequency generation spectrometer with a wide tunability of the ultraviolet probe

We have constructed a multiplex infrared-ultraviolet (IR-UV) sum-frequency generation (SFG) spectrometer that has a wide tunable range (235-390 nm) of the UV probe wavelength. The tunable UV probe was obtained by doubling the signal output of an optical parametric amplifier pumped by a 400 nm picosecond pulse. A prism monochromator was used as a tunable sharp-cut bandpass filter to reduce stray light due to the scattering of the UV probe so that any wavelength within the tunable range can be chosen as that of the UV probe. The SFG spectra of p-mercaptobenzoic acid on a gold substrate was measured with 289 and 334 nm UV probes. The SFG vibrational band intensities due to the carbonyl stretch mode and a phenyl ring stretch mode measured with the 289 nm probe were approximately three times larger than those measured with the 334 nm probe. The enhancement was ascribed to an electronic resonant effect.     

Efficient femtosecond optical parametric generator with a birefringent delay compensator

A novel method based on a birefringent crystal is presented to compensate for the group-velocity mismatch between a femtosecond pulsed pump and the signal or idler in an optical parametric generator (OPG). With a thin calcite plate inserted between two beta-barium borate crystals for synchronization, an efficient four-pass OPG pumped by a frequency-doubled ~200-fs Ti:sapphire laser is obtained. The conversion efficiency is almost doubled throughout the whole tunable region compared with a conventional OPG pumped at the same power density, indicating that the total conversion efficiency of femtosecond optical parametric amplifier system can be raised significantly by use of this new four-pass OPG to generate the seed.     

Optical parametric chirped-pulse amplifier as an alternative to Ti:sapphire regenerative amplifiers

We demonstrated a high-pulse energy, femtosecond-pulse source based on optical parametric chirped-pulse amplification. We successfully amplified 1-microm broadband oscillator pulses to 31 mJ and recompressed them to 310-fs pulse duration, at a 10-Hz repetition rate. The gain in our system is 6 x 10(7), achieved by the single passing of only 40 mm of gain material pumped by a commercial Q-switched Nd:YAG laser. This relatively simple system replaces a more complex Ti:sapphire regenerative-amplifier-based chirped-pulse amplification system. Numerous features in design and performance of optical parametric chirped-pulse amplifiers make them a preferred alternative to regenerative amplifiers based on Ti:sapphire in the front end of high-peak-power lasers.     

Operation of a Ti:sapphire laser pumped by a 499-nm green laser

We report, for the first time, to our knowledge, the operation of a tunable Ti:sapphire laser pumped by a third-order Raman XeCl-H(2) laser system at 499 nm with a 60-ns pulse duration. The slope efficiency is 59% for this laser, producing pulses of 20-ns duration. The highest conversion-energy efficiency obtained is 41%, with an output energy of 1.2 mJ. The tuning range for a single set of cavity mirrors is 680-834 nm and is limited mainly by the mirror reflectivity. This study shows that a combined laser system based on a XeCl excimer laser can offer wavelength diversity.     

Amplified Spontaneous Emission Reduction by Use of Stimulated Brillouin Scattering: 2-ns Pulses from a Ti:Al(2)O(3) Amplifier chain

We constructed a cw Ti:Al(2)O(3) master oscillator-dye preamplifier-Ti:Al(2)O(3) power amplifier system that generates <2-ns, 100-mJ pulses. The system is tunable from 750 to 890 nm and has a repetition rate of 30 Hz. The output pulse has a near Fourier-transform-limited bandwidth of ~240 MHz. Backward stimulated Brillouin scattering is used to control the growth of amplified spontaneous emission (ASE). The content of ASE in the final output is under our detection limit (<10(-4)) for the entire tuning range.     

Regenerative amplification of femtosecond pulses at 745 nm in Ti:sapphire

A regenerative amplifier for femtosecond pulses that operates at a wavelength off the peak gain of Ti:sapphire is reported. Apair of prisms and an adjustable slit are used in the intracavity space so that the operating wavelength can be tuned to 745 nm. The amplified and compressed pulse is 92 fs (Gaussian profile assumed) at an energy of 1 mJ. The pumping efficiency is 12.5%.     

Kilohertz pulse repetition frequency slab Ti:sapphire lasers with high average power (10 W)

High-average-power broadband 780-nm slab Ti:sapphire lasers, pumped by a kilohertz pulse repetition frequency copper vapor laser (CVL), were demonstrated. These lasers are designed for damage-free power scaling when pumped by CVL's configured for maximum output power (of order 100 W) but with poor beam quality (M(2) ~ 300). A simple Brewster-angled slab laser side pumped by a CVL produced 10-W average power (1.25-mJ pulses at 8 kHz) with 4.2-ns FWHM pulse duration at an absolute efficiency of 15% (68-W pump power). Thermal lensing in the Brewster slab laser resulted in multitransverse mode output, and pump absorption was limited to 72% by the maximum doping level for commercially available Ti:sapphire (0.25%). A slab laser with a multiply folded zigzag path was therefore designed and implemented that produced high-beam-quality (TEM(00)-mode) output when operated with cryogenic cooling and provided a longer absorption path for the pump. Excessive scattering of the Ti:sapphire beam at the crystal surfaces limited the efficiency of operation for the zigzag laser, but fluorescence diagnostic techniques, gain measurement, and modeling suggest that efficient power extraction (>15 W TEM(00), >23% efficiency) from this laser would be possible for crystals with an optical quality surface polish.     

Construction of a subnanosecond time-resolved, high-resolution ultraviolet resonance Raman measurement system and its application to reveal the dynamic structures of proteins

A subnanosecond time-resolved ultraviolet (UV) resonance Raman system has been developed to study protein structural dynamics. The system is based on a 1 kHz Nd:YLF-pumped Ti:Sapphire regenerative amplifier with harmonic generation that can deliver visible (412, 440, 458, and 488 nm) and UV (206, 220, 229, and 244 nm) pulses. A subnanosecond (0.2 ns) tunable near-infrared pulse from a custom-made Ti:Sapphire oscillator is used to seed the regenerative amplifier. A narrow linewidth of the subnanosecond pulse offers the advantage of high resolution of UV resonance Raman spectra, which is critical to obtain site-specific information on protein structures. By combination with a 1 m single spectrograph equipped with a 3600 grooves/mm holographic grating and a custom-made prism prefilter, the present system achieves excellent spectral (<10 cm(-1)) and frequency (approximately 1 cm(-1)) resolutions with a relatively high temporal resolution (<0.5 ns). We also report the application of this system to two heme proteins, hemoglobin A and CooA, with the 440 nm pump and 220 nm probe wavelengths. For hemoglobin A, a structural change during the transition to the earliest intermediate upon CO photodissociation is successfully observed, specifically, nanosecond cleavage of the A-E interhelical hydrogen bonds within each subunit at Trpalpha14 and Trpbeta15 residues. For CooA, on the other hand, rapid structural distortion (<0.5 ns) by CO photodissociation and nanosecond structural relaxation following CO geminate recombination are observed through the Raman bands of Phe and Trp residues located near the heme. These results demonstrate the high potential of this instrument to detect local protein motions subsequent to photoreactions in their active sites.     

Ti: Sapphire Pumped Femtosecond Optical Parametric Oscillator Exhibiting Soliton Formation

Abstract

The configuration and operation of a singly resonant Ti: sapphire pumped optical parametric oscillator (OPO) based on KTP is discussed. Cavity arrangements with and without dispersion compensation are described and the generation of sub-40 fs transform-limited pulses is highlighted. Evidence for soliton pulse formation in the OPO is presented and good quantitative agreement with existing theory is implied. Results of amplitude and phase noise measurements of the OPO are given and compared with those of the pump laser. Generation of pulses at several visible wavelengths by non-phase-matched processes is also briefly discussed.