反应型增容剂PS-co-GMA在PA1010/ABS共混体系中的增容作用

以PS -co -GMA作为PA10 10 /ABS共混体系的反应型增容剂 ,探讨了增容剂的含量对共混体系力学性能的影响。同时 ,利用熔融共混法制备了PA10 10 /ABS -g -GMA共混体系 ,比较了两种增容方式对共混体系力学性能的影响。     

高密度聚乙烯／尼龙1010共混体系的研究

采用接枝共聚方法,合成了高密度聚乙烯与马来酸酐,甲基丙烯酸和丙烯酸丁酯的接枝共聚物增容剂,研究了增容剂中接枝单体的种类及含量和增容剂用量等因素对高密度聚乙烯／尼龙1010共混体系力学性能的影响,结果表明在不同类型的接枝共聚物中以聚乙烯马来酸酐接枝共聚物对HDPE／PA1010共混体系的增容效果最好,在接枝单体含量和增容剂用量分别为4％－6％和5％左右时,共混体系的力学性能最好。     

PP-g-MAH和PP-g-GMA增容PP/PA6共混体系的研究

将自制的PP—g—MAH（聚丙烯接枝马来酸酐）及PP—g—GMA（聚丙烯接枝甲基丙烯酸缩水甘油酯）作为PP／PA6共混体系的相容剂，研究了加入聚丙烯接枝物后PP，PA6塑料合金的各种力学性能及形态结构。结果表明：在PP／PA6共混物中加入PP—g—MAH后，共混物的力学性能得到明显的提高．添加PP—g—MAH对不同比例PP／PA6共混物力学性能的影响不同；用PP—g—MAH和PP—g—GMA两种接枝物共同作为相容剂加入到PP／PA6共混物中比单独使用一种的效果要好。共混物的SEM照片表明。PP—g—MAH是PP／PA6共混物的有效增容剂。     

反应型增容剂PS-co-GMA在PA1010/ABS共混体系中的增容作用

以ＰＳ－ｃｏ－ＧＡＭ作为ＰＡ１０１０／ＡＢＳ共混体系的增容剂,探讨了增容剂的含量对共混体系力学性能的影响,同时,利用熔融共混法制备了ＰＡ１０１０／ＡＢＳ－ｇ－ＧＭＡ共混体系,比较了两种增容方式对共混体系力学性能的影响。     

聚丙烯固相接枝物增容PA6/PS共混体系

采用FTIR和WAXD研究了聚丙烯固相接枝苯乙烯（St)和马来酸酐（MAH）的结构，并研究了它对聚酰胺6／聚苯乙烯（PA6／PS）共混体系力学性能的影响及其非等温结晶动力学，研究结果表明，PP上可固相接枝St,MAH;gPP(PP接枝St和MAH双组分接枝物）增容PA6／PS的非等温结晶动力学与MandelKern理论基本吻合。     

超韧PA6/ABS合金的制备

以苯乙烯-马来酸酐（SMA）共聚物为增容剂，考察了ABS及SMA的含量对PA6／ABS共混体系的力学性能的影响；并利用SEM研究了PA6／ABS冲击断面的相结构。研究表明：SMA是PA6／ABS共混体系的有效增容剂。随着其含量的增加，分散相ABS粒子的尺寸减小，分散更加均匀，能显著地改善PA6／ABS共混物的冲击、拉伸和弯曲性能。在该共混体系中，ABS含量的增加能够大幅度地提高PA6／ABS共混物的冲击韧性；但当ABS含量超过10％时，将使PA6／ABS共混物的拉伸和弯曲性能明显下降。SMA的添加量为0．5％，且质量比为90／10的PA6／ABS共混体系能保持较好的加工性能，制备的PA6／ABS合金具有最佳的综合力学性能和超高韧性．Izod缺口冲击强度高达1200J／m。     

共混方式对ABS／PA6／SMA共混体系形态和力学性能的影响

以苯乙烯-马来酸酐共聚物（SMA）为反应增容剂，研究不同共混工艺和ABS／PA6配比对三共混体系聚集态结构和力学性能的影响。结果表明：SMA对共混体系增容效果显著，并明显改善了ABS／PA6共混体系的力学性能。其中当PA6用量为30份和40份时，SMA先与ABS共混再与PA6共混的方式所生成共混物的性能优于SMA先与PA6共混再与ABS共混的方式。PA6用量为30份时性能最好，共混物的分散相尺寸达到最小值0．31μm，分散相颗粒PA6周长面积比为最大值0．46，拉伸强度和冲击强度也分别为最大值63．2MPa和8．29kJ／m^2。当PA6用量达到45份时，共混方式对共混物的力学性能影响不大。研究表明，当ABS为连续相时，共混方式可以强烈地影响ABS／PA6共混物体系的聚集态结构和力学性能，而PA6和ABS向共连续相发展时，共混方式对ABS／PA6聚集态结构和力学性能则影响不大。     

PPS/PA1010合金的制备及其力学性能研究

选用丙烯酸接枝聚丙烯（PP-g-AA）和自制的甲基丙烯酸缩水甘油酯（GMA）嵌段共聚苯乙烯（St）接枝聚丙烯[PP—g-（GMA—CO—St）]为增容剂,采用双螺杆挤出机熔融挤出法制备了PPS／PA1010／PP—g—AA合金和PPS／PA1010／PP-g-（GMA—CO-St）合金,并分别对两种合金的力学性能进行了研究。结果表明,在保持合金其它力学性能不下降的情况下,随着PP—g—AA含量的增加,共混合金的冲击强度先提高后降低,当PP-g—AA含量为7份时,冲击强度比原合金提高了86．7％,比纯PPS提高了39．3％;而随着PP—g-（GMA—CO—St）含量的增加,冲击强度也有明显提高。     

橡胶改性PP共混体系的研究

本文研究了SBR／PP共混比、硫化体系、不同橡胶以及增容剂对橡胶／PP共混物力学性能的影响。试验得出：橡塑比（SBR／PP）在30／70,采用半有效硫化体系（CZ／S）时,所制得共混物力学性能较好,共混体系PP／POE的综合性能比PP／EPDM、PP／SBR、PP／NBR共混体系要好,加入增容剂PP－g－MAH可以显著提高共混物的力学性能。     

PP/PA6/EPDM-g-GMA合金性能的研究

在聚丙烯（PP）中加入10％～40％（质量分数）的PA6及反应增容剂EPDM—g—GMA对PP进行共混改性．观察和分析了共混合金的形貌及等温结晶形态，测试了合金的力学性能。结果表明：PP／PA6体系中加入EPDM—g—GMA后相容性改善；PP球晶尺寸随PA6的混入而减小，且PA6结晶相分布PP晶区内和PP晶区之问，加入EPDM—g—GMA后PA6结晶相尺寸减小；PP／队6体系中加入EPDM—g—GMA可起到反应增容和橡胶增韧的协同效应，使材料的韧性比纯PP明显提高；PP／PA6体系的杨氏模量高于PP，加入EPDM-g-GMA后杨氏模量比未增容体系提高不显著；PP／PA6体系的屈服强度随PA6用量的增加而下降，加入EPDM—g-GMA后屈服强度高于未增容体系但略低于PP。     

PA-1010/ABS合金的性能研究

研究了以自制的马来酸酐 (MAH)接枝改性ABS(MABS)作为PA 10 10 /ABS增容剂所形成的PA 10 10 /ABS合金的性能。研究结果表明 ,随ABS中马来酸酐接枝量的上升 ,PA 10 10 /ABS合金的冲击强度提高 ,保持PA 10 10与ABS用量在某一恰当配比范围内 ,可得到冲击强度高 ,维卡软化温度较高的合金。     

PA6/ABS合金的研制

以POE-g-MAH为增容剂,应用双螺杆挤出机制备通过熔融共混法制备了PA6/ABS合金,研究了ABS树脂的用量对合金的力学性能的影响。结果表明:在POE-g-MAH存在的条件下,随着ABS用量增大,共混物的拉伸强度逐渐增大,简支梁缺口冲击强度则逐渐减小,而无缺口冲击强度先减小后增大。在混和体系中,POE-g-MAH具有增容和增韧的双重作用。     

Effects of olefin‐based compatibilizers on the morphology,thermal and mechanical properties of ABS/polyamide‐6 blends

In this study, commercially available epoxidized and maleated olefinic copolymers, EMA‐GMA (ethylene‐methyl acrylate‐glycidyl methacrylate) and EnBACO‐MAH (ethylene‐n butyl acrylate‐carbon monoxide‐maleic anhydride), were used at 0, 5, and 10% by weight to compatibilize the blend composed of ABS (acrylonitrile‐butadiene‐styrene) terpolymer and PA6 (polyamide 6). Compatibilizing performance of these two olefinic polymers was investigated from blend morphologies, thermal and mechanical properties as a function of blend composition, and compatibilizer loading level. Scanning electron microscopy (SEM) studies showed that incorporation of compatibilizer resulted in a fine morphology with reduced dispersed particle diameter at the presence of 5% compatibilizer. The crystallization behavior of PA6 phase in the blends was explored for selected blend compositions by differential scanning calorimetry (DSC). At high compatibilizer level a decrease in the degree of crystallization was observed. In 10% compatibilizer containing blends, formation of γ‐crystals was observed contrary to other compatibilizer compositions. The behavior of the compatibilized blend system in tensile testing showed the negative effect of using excess compatibilizer. Different trends in yield strengths and strain at break values were observed depending on compatibilizer type, loading level, and blend composition. With 5% EnBACO‐MAH, the blend toughness was observed to be the highest at room temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 926–935, 2007     

Investigation on the correlation between rheology and morphology of PA6/ABS blends using ethylene acrylate terpolymer as compatibilizer

Phase morphology and rheological behavior of polyamide 6 (PA6)/acrylonitrile butadiene styrene (ABS) polymers blends was studied using scanning electron microscopy and rheometry. The results showed that the phase morphology and rheological properties depends on blend composition. We evaluated the effect of addition of ABS as dispersed phase and EnBACO‐MAH (ethylene n‐butyl acrylate carbon monoxide maleic anhydride) as a compatibilizer on the morphological and rheological behaviors of PA6/ABS blends. It was concluded that there is a good agreement between the results obtained from rheological and morphological studies. As a consequence, addition of the ABS and compatibilizer weight percent led to a significant change in morphological structure and a great mounting in the viscosity as well as the elasticity. The rheological properties results demonstrate that adding compatibilizer to polymer blends led to increasing the crossover point, which shows a transition from a high viscous to a considerably more elastic behavior. Also, the slow transition of relaxation time peak from the peak of the PA6 to the peak of the ABS implies increasing the miscibility of the PA6/ABS blend components by increasing compatibilizer content. In addition, the Carreau–Yasuda model was used to extract information on rheological properties (zero shear viscosity and relaxation time) for PA6/ABS/EnBACO‐MAH blends by fitting the experimental data with this model. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of compatibilizer in acrylonitrile‐butadiene‐styrene toughened nylon 6 blends: Ductile–brittle transition temperature

The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003     

ABS/PA6共混体系的反应性增容研究

用少量苯乙烯-马来酸酐(SMA)作为相容剂改善ABS/PA6共混体系的相容性,研究了共混体系(固定ABS/PA6质量比为70/30)中相容剂的最佳用量,以及随相容剂含量变化引起的体系形态结构和力学性能变化情况,同时探讨了体系组成与性能关系的微观机理。还研究了环境因素对ABS/PA6共混体系性能的影响。     

相容剂和加工工艺对PA1010/PP共混体系形态和力学性能的影响

以马来酸酐（MAH）和苯乙烯（St）多单体熔融接枝聚丙烯[PP-g-(MAH-co-St）]为相容剂,制备了聚酰胺10101/聚丙烯（PA1010/PP）共混体系。用毛细管流变仪、扫描电子显微镜、力学性能测试等方法研究了和加工工艺相容剂对PA1010/PP共混体系的形态和力学性能的影响。结果表明,相容剂PP-g-(MAH-co-St)有效降低了PA1010/PP共混体系的熔体流动速率;该共混体系熔体属于假塑性流体,熔体黏度随PP-g-(MAH-co-St)含量的增加逐渐增大;随着相容剂含量的增加,PA1010/PP共混体系中分散相PP的粒径逐步减小,力学性能得到改善,PA1010/PP/PP-g-(MAH-co-St)为70/25/5和70/20/10的共混体系的拉伸强度分别比PA1010/PP (70/30)共混体系提高了55.0 %和61.9 %,冲击强度分别提高了61.0 %和129.7 %;剪切速率为706.5 s-1时出现熔体破裂现象,剪切速率为5002.65 s-1时出现严重熔体破裂。     

Effect of maleic anhydride grafted polybutadiene on the compatibility of polyamide 66/acrylonitrile‐butadiene‐styrene copolymer blend

The addition of maleic anhydride grafted polybutadiene (PB‐g‐MAH) can greatly improve the compatibility of polyamide 66 (PA66)/acrylonitrile‐butadiene‐styrene copolymer (ABS) blends. Unlike the commonly used compatibilizers in polyamide/ABS blends, PB‐g‐MAH is compatible with the ABS particles' core phase polybutadiene (PB), rather than the shell styrene‐acrylonitrile (SAN). The compatibility and interaction of the components in the blends were characterized by Fourier transform‐infrared spectra (FTIR), Molau tests, melt flow index (MFI), dynamic mechanical analyses (DMA), and scanning electron microscopic (SEM) observations. The results show that PB‐g‐MAH can react with the amino end groups in PA66 while entangle with the PB phase in ABS. In this way, the compatibilizer anchors at the interface of PA66/ABS blend. The morphology study of the fracture sections before and after tensile test reveals that the ABS particles were dispersed uniformly in the PA66 matrix and the interfacial adhesion between PA66 and ABS was increased significantly. The mechanical properties of the blends thus were enhanced with the improving of the compatibility. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers