共查询到18条相似文献,搜索用时 171 毫秒
1.
以球形纤维素珠体为原料,丙烯腈(AN)和丙烯酰胺(AM)为单体,硝酸铈铵和过硫酸钾(KPS)为引发剂,制备纤维素珠体-AN-AM接枝共聚物,并通过正交单因素实验,研究了反应温度、引发剂用量、单体用量、反应时间等因素对接枝效果的影响。实验结果表明:当反应温度为60℃,引发剂硝酸铈铵用量为20%,KPS用量为15%(引发剂与单体AN的质量百分比),单体AN浓度为0.75 mol/L,AM浓度为0.28 mol/L,硝酸浓度为0.14 mol/L,反应时间为3 h时,接枝效果最好。此条件下,AN、AM与纤维素的接枝率可达259.4%,接枝效率可达49.40%。 相似文献
2.
微波辐射下壳聚糖-丙烯酰胺接枝物的合成及其絮凝性能研究 总被引:1,自引:1,他引:1
以硝酸铈铵作为引发剂、丙烯酰胺为单体,用微波辐射法合成了壳聚糖-丙烯酰胺接枝共聚物。通过正交试验考察反应条件对接枝率和接枝效率的影响,得出最佳工艺条件为:反应时间12 min,引发剂浓度5 mmol/L,丙烯酰胺和壳聚糖质量比5:1,反应温度40℃。最佳条件下接枝率和接枝效率分别达到148.6%和44.0%。壳聚糖接枝物与聚丙烯酰胺(PAM)对高岭土悬浮液的絮凝对比试验表明:在酸性条件下接枝物与PAM的絮凝效果相近;在中性和碱性条件下接枝物的絮凝性能优于PAM。 相似文献
3.
壳聚糖-甲基丙烯酰氧乙基三甲基氯化铵接枝共聚物的制备与絮凝性能研究 总被引:3,自引:0,他引:3
以壳聚糖和甲基丙烯酰氧乙基三甲基氯化铵(DMC)为原料,硝酸铈铵为引发剂,Span-20为乳化剂,通过反相乳液聚合技术,合成了壳聚糖-DMC接枝共聚物。通过正交试验考察了反应条件对接枝度的影响,得出的最佳工艺条件为:反应时间5 h、引发剂浓度16 mmol/L、壳聚糖与DMC质量比1:6、油水体积比1:1。最佳条件下平均接枝度达到110 %。将得到的壳聚糖接枝共聚物用作絮凝剂处理高岭土悬浮液,结果表明其絮凝性能优于壳聚糖和聚丙烯酰胺(PAM),且在pH值6.0、投加量为2.0 mg/L时絮凝效果最佳。 相似文献
4.
5.
6.
7.
研究了以硝酸铈铵(CAN)、硝酸铈铵-乙二胺四乙酸二钠(CAN-EDTA)、硝酸铈铵-过硫酸钾(CAN—KPS)三种引发体系分别引发淀粉接枝丙烯酰胺共聚反应。通过正交实验并作图,找到了它们的最佳工艺条件。应用其最佳工艺条件下的接枝率(G)、单体转换率(CM)和引发剂用量来比较三者中的最佳引发体系。试验最终得出,硝酸铈铵一过硫酸钾(CAN-KPS)复合引发体系是三者中最好的。 相似文献
8.
淀粉与丙烯酰胺的接枝共聚 总被引:6,自引:0,他引:6
本文研究了在硝酸铈铵作用下,淀粉和丙烯酰胺接枝共聚合的反应规律,探讨了引发剂浓度、单体浓度、pH值、反应时间和反应温度对接枝聚合的影响,并对不同的引发体系引发淀粉—丙烯酰胺接枝聚合进行了比较,结果表明,以硝酸铈铵引发的淀粉—丙烯酰胺接枝聚合所产生的均聚物少,引发效率高。 相似文献
9.
两种不同引发剂在木薯淀粉接枝丙烯酸反应的研究 总被引:9,自引:0,他引:9
详细地研究了淀粉接枝丙烯酸反应过程中 ,两种不同的引发剂过硫酸钾 -亚硫酸氢钠和硝酸铈铵在淀粉接枝丙烯酸共聚反应的影响 ,对一些反应条件如引发剂浓度、反应的温度、单体的浓度、单体的中和度、反应的时间等进行了单因素试验 ,以接枝率 ,单体转化率 ,接枝效率为主要考查目标 ,从而得出试验的最佳条件。在过硫酸钾-亚硫酸氢钠的引发下 ,最佳的反应条件是 :反应温度 35℃ ,引发剂的浓度是 2 .8m mol/· L- 1 ,丙烯酸的浓度是1.1mol· L- 1 ,反应时间 3h,中和度为 80 % 相似文献
10.
11.
Glycidyl methacrylate was graft-copolymerized onto cotton cellolose using both photo-and chemical-initiation techniques using different initiators. The photoinitiators used were uranyl nitrate, ceric ammonium nitrate, and benzoin ethyl ether, whereas the chemical initiators used were ceric ammonium nitrate and potassium persulfate. Optimization of various parameters of grafting, viz., time, temperature, initiator, and monomer concentrations, was carried out. Ceric ammonium nitrate gave the maximum and almost identical values of graft add-on, by both grafting techniques, at equivalent cocentration of the monomer. Use of optimized conditions of ceric ammonium nitrate-photoinitiated grafting for sodium hydroxide-swollen substrate as well as for grafting baths incorporating acids enhanced the graft level. © 1994 John Wiley & Sons, Inc. 相似文献
12.
淀粉接枝丙烯酸聚合型絮凝剂的合成及絮凝性能研究 总被引:1,自引:0,他引:1
以可溶性淀粉为主要原料,以丙烯酸为接枝单体,硝酸铈铵和过硫酸钾为复合引发剂,采用溶液聚合的方法对糊化处理后的淀粉进行接枝聚合,合成出环保型淀粉衍生物水处理絮凝剂。通过对接枝聚合反应温度、反应时间、引发剂用量以及丙烯酸单体用量等因素对接枝率影响的研究,确定较佳的接枝产物合成条件:淀粉10g,单体丙烯酸用量10mL,硝酸铈铵和过硫酸钾(摩尔比1:1)复合引发体系用量2mmol,接枝反应温度50℃,接枝反应时间3h,接枝率达到43.2%。利用选煤后的废水对其产品絮凝性能进行实验研究,确定较佳的废水絮凝处理条件。 相似文献
13.
14.
15.
A. Fakhru'L‐Razi Isam Y. M. Qudsieh Wan Md Zin Wan Yunus Mansor B. Ahmad Mohamad Zaki Ab. Rahman 《应用聚合物科学杂志》2001,82(6):1375-1381
The graft copolymerization of methyl methacrylate (MMA) onto sago starch was carried out in aqueous media by different initiators of ceric ammonium nitrate (CAN) and potassium persulfate (PPS) and under a nitrogen gas atmosphere. Using CAN as an initiator, the maximum percentage of grafting (%G) was ascertained to be 246% at the following optimum conditions: a 70°C reaction temperature, a 2‐h reaction period, 2.0 mmol of CAN, 0.4 mmol of nitric acid, and 141 mmol of MMA. The maximum %G achieved with PPS as the initiator was 90%. The optimum conditions were a 50°C reaction temperature, a 1.5‐h reaction period, 47 mmol of monomer, and 1.82 mmol of PPS. The grafting of MMA onto sago starch was confirmed by the IR spectra of pure sago starch, MMA, and MMA grafted sago starch. This material may have application as a biodegradable plastic. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1375–1381, 2001 相似文献
16.
氧化还原引发淀粉与丙烯酸接枝共聚研究 总被引:6,自引:0,他引:6
研究了马铃薯淀粉与丙烯酸的接枝共聚反应,以过硫酸钾-亚硫酸氢钠为氧化还原引发体系,考察了不同引发剂浓度、单体浓度、反应温度、反应时间等对单体转化率、接枝率和接枝效率的影响;用红外光谱对共聚物进行了表征。结果表明,采用氧化还原引发体系可使聚合反应低温快速进行,并确定反应较佳条件。 相似文献
17.
研究了硝酸铈铵为引发剂的氧化还原体系中,甲基丙烯酸甲酯(MMA)与菠萝叶纤维以水为介质的非均相接枝聚合反应。以纤维接枝率作为聚合效果评价指标,确定了优化的反应条件:铈离子浓度0.006 mol/L,氢离子浓度0.06 mol/L,MMA浓度0.4 mol/L,反应温度50 ℃,反应时间3 h,接枝率达到185 %。用扫描电镜(SEM)、X射线衍射(XRD)、红外光谱(FT-IR)、热重分析(TG)、纤维强力仪等分析MMA接枝前后纤维的结构和理化性质,结果显示,菠萝叶纤维接枝MMA后,改变了纤维分子原有的规整排列,纤维部分结晶区受到破坏,纤维呈松散状且更柔软,抗拉性能下降,而耐热性有所增强。同时,研究结果也显示了菠萝叶纤维MMA接枝率越高,则纤维的吸湿率越低,耐酸碱性能越强。 相似文献
18.
The graft copolymerization of methyl methacrylate (MMA) onto viscose fibers were studied under photoactive conditions with visible light using titanium(III) chloride—potassium persulfate as redox initiator in a limited aqueous system. Polymerization carried out in the dark at 40 ± 1°C produced little graft copolymer whereas that in the presence of light at 40 ± 1°C produced significant grafting. Percent grafting, percent total conversion, and grafting efficiency (%) were studied by varying time, initiator concentration, monomer concentration, solvent composition, and pH of the medium. High percent grafting (~ 200%), high grafting efficiency (~ 98%), and percent total conversion (~ 47%) were obtained with little homopolymer formation. A suitable mechanism for grafting has been discussed and also the characterization of the grafted fibers were studied by Fourier transform infrared (FTIR) spectroscopy, thermogravimetry and scanning electron microscopy (SEM). © 1992 John Wiley & Sons, Inc. 相似文献