Thermal Expansion of the Low-Temperature Form of BaB2O4

Thermal expansion of the low-temperature form of BaB₂O₄ (β-BaB₂O₄) crystal has been measured along the principal crystallographic directions over a temperature range of 9° to 874°C by means of high-temperature X-ray powder diffraction. This crystal belongs to the trigonal system and exhibits strongly anisotropic thermal expansions. The expansion along the c axis is from 12.720 to 13.214 Å (1.2720 to 1.3214 nm), whereas it is from 12.531 to 12.578 Å (1.2531 to 1.2578 nm) along the a axis. The expansions are nonlinear. The coefficients A, B , and C in the expansion formula L _t = L ₀(1 + At + Bt ²+ Ct ³) are given as follows: a axis, A = 1.535 × 10⁻⁷, B = 6.047 × 10⁻⁹, C = -1.261 × 10⁻¹²; c axis, A = 3.256 × 10⁻⁵, B = 1.341 × 10⁻⁸, C = -1.954 × 10⁻¹²; and cell volume V, A = 3.107 × 10⁻⁵, B = 3.406 × 10⁻⁸, C = -1.197 × 10⁻¹¹. Based on α _t = (d L _t /d t )/ L ₀, the thermal expansion coefficients are also given as a function of temperature for the crystallographic axes a , c , and cell volume V.     

Compressive Creep and Oxidation Resistance of an Si3N4 Material Fabricated in the System Si3N4-Si2N2O-Y2Si2O7

The compressive creep behavior and oxidation resistance of an Si₃N₄/Y₂Si₂O₇ material (0.85Si₃N₄+0.10SiO₂+0.05Y₂O₃) were determined at 1400°C. Creep re sistance was superior to that of other Si₃N₄ materials and was significantly in creased by a preoxidation treatment (1600°C /120 h). An apparent parabolic rate constant of 4.2 × 10⁻¹¹ kg²·m-⁴·s⁻¹ indicates excellent oxidation resistance.     

Tribological Behavior of Ti2SC at Ambient and Elevated Temperatures

The tribological properties of Ti₂SC were investigated at ambient temperatures and 550°C against Ni-based superalloys Inconel 718 (Inc718) and alumina (Al₂O₃) counterparts. The tests were performed using a tab-on-disk method at 1 m/s and 3N (≈0.08 MPa). At room temperature, against the superalloy, the coefficient of friction, μ, was ∼0.6, and at ∼8 × 10⁻⁴ mm³·(N·m)⁻¹ the specific wear rate (SWRs), was high. However, against Al₂O₃, at ∼5 × 10⁻⁵ mm³·(N·m)⁻¹ and ∼0.3, the SWRs and μ were significantly lower, which was presumably related to more intensive tribo-oxidation at the contact points. At 550°C, the Ti₂SC/Inc718 and Al₂O₃ tribocouples demonstrated comparable μ's of ∼0.35–0.5 and SWRs of ∼7–8 × 10⁻⁵ mm³·(N·m)⁻¹. At 550°C, all tribosurfaces were covered by X-ray amorphous oxide tribofilms. At present, Ti₂SC is the only member of a family of the layered ternary carbides and nitrides (MAX phases) that can be used as a tribo-partner against Al₂O₃ in the wide temperature range from ambient to 550°C.     

Phase Equilibria in the Spinel Region of the System FeO-Fe2O3-Al2O3

Phase relations in the spinel region of the system FeO-Fe₂O₃-Al₂O₃ were determined in CO₂ at 1300°, 1400°, and 15000°C and for partial oxygen pressures of 4 × 10⁻⁷ and 7 × 10⁻¹⁰ atmospheres at 15OO°C. The spinel field extends continuously from Fe₃O_4-x to FeAl₂O_4+z.     

Thermal Expansion Behavior of Titanium-Doped La(Sr)CrO3 Solid Oxide Fuel Cell Interconnects

La_0.8Sr_0.2Cr_0.9Ti_0.1O₃ perovskite has been designed as an interconnect material in high-temperature solid oxide fuel cells (SOFCs) because of its thermal expansion compatibility in both oxidizing and reducing atmospheres. La_0.8Sr_0.2Cr_0.9Ti_0.1O₃ shows a single phase with a hexagonal unit cell of a = 5.459(1) Å, c = 13.507(2) Å, Z = 6 and a space group of R -3 C . Average linear thermal expansion coefficients of this material in the temperature range from 50° to 1000°C were 10.4 × 10⁻⁶/°C in air, 10.5 × 10⁻⁶/°C under a He–H₂ atmosphere (oxygen partial pressure of 4 × 10⁻¹⁵ atm at 1000°C), and 10.9 × 10⁻⁶/°C in a H₂ atmosphere (oxygen partial pressure of 4 × 10⁻¹⁹ atm at 1000°C). La_0.8Sr_0.2Cr_0.9Ti_0.1O₃ perovskite with a linear thermal expansion in both oxidizing and reducing environments is a promising candidate material for an SOFC interconnect. However, there still remains an air-sintering problem to be solved in using this material as an SOFC interconnect.     

Porous Glass-Ceramics with a Skeleton of the Fast-Lithium-Conducting Crystal Li1+xTi2−xAlx(PO4)3

Porous glass-ceramics with a skeleton of the fast-lithium-conducting crystal Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ (where x = 0.3–0.5) were prepared by crystallization of glasses in the Li₂O─CaO─TiO₂─Al₂O₃–P₂O₅ system and subsequent acid leaching of the resulting dense glass-ceramics composed of the interlocking of Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ and β-Ca₃(PO₄)₂ phases. The median pore diameter and surface area of the resulting porous Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ glass-ceramics were approximately 0.2 μm and 50 m²/g, respectively. The electrical conductivity of the porous glass-ceramics after heating in LiNO₃ aqueous solution was 8 × 10⁻⁵ S/cm at 300 K or 2 × 10⁻² S/cm at 600 K.     

Deviation from Stoichiometry in Cr2O3 at High Oxygen Partial Pressures

The deviation from stoichiometry, δ, in Cr₂−δO₃ was measured by a tensivolumetric method in the high pO₂ range of ≊10⁴ to 10⁴ Pa at 1100°C. The value of δ, or chromium vacancy concentration, was≊9×10⁻⁵ mol/mol Cr₂O₃ in air for Cr₂O₃ with 99.999% purity. The chemical diffusion coefficient, DT, determined from equilibration data was ≊4.6× cm²·s⁻¹ at 1100°C for pO₂= 2.2 ×10¹ Pa. The self-diffusion coefficient of Cr ions was calculated from and δ and found to be≊1.6×10-17 cm²-s⁻¹, in good agreement with recently measured values.     

Grain Growth in Fe3O4

Sintering and microstructural evolution were studied in Fe₃O₄ as a model system for spinel ferrites. Fe₃O₄ powder, purified by the salt-crystallization method, was sintered to ∼99.5% density in a CO-CO₂ atmosphere. The p _O2 Of the sintering atmosphere drastically affects the microstructure (grain size) of sintered Fe₃O₄ without significantly affecting density. The measured grain-boundary mobilities, M , of Fe₃O₄ fit the equation M=M ₀( T ) p _O2^−1/2 with M ₀( T ) = 2.5×10⁵ exp[-(609kJ·mol-¹/ RT ](m/s)(N/m²)^−l. The grain-boundary migration process appeared to be pore-drag controlled, with lattice diffusion of oxygen as the most likely rate-limiting step.     

Pyroelectric and Dielectric Properties of Mn Modified 0.82Bi0.5Na0.5TiO3–0.18Bi0.5K0.5TiO3 Lead-Free Thick Films

MnO-doped 0.82Bi_0.5Na_0.5TiO₃–0.18Bi_0.5K_0.5TiO₃(NBT–KBT) thick films with thickness about 40 μm have been prepared using screen printing on Pt electroded alumina substrates. The strong pyroelectric coefficient of 3.8 × 10⁻⁴ C·(m²·°C)^–1 was observed in 1.0 mol% MnO-doped-thick films, and the calculated detectivity figure of merit as high as 1.1 × 10⁻⁵ Pa^−0.5, which can be comparable to that of the commonly used lead based materials. The enhancement of the pyroelectric performances is attributed to the reductions in dielectric constant and loss and the improvements in the pyroelectric coefficient, which can be ascribed to the Mn acts as a hard dopant in the NBT–KBT lattice, creating oxygen vacancies and pinning the residual domains.     

Preliminary Observations on Phase Relations in the "V2O3–FeO" and V2O3–TiO2 Systems from 1400°C to 1600°C in Reducing Atmospheres

Phase relations within the "V₂O₃–FeO" and V₂O₃–TiO₂ oxide systems were determined using the quench technique. Experimental conditions were as follows: partial oxygen pressures of 3.02 × 10⁻¹⁰, 2.99 × 10⁻⁹, and 2.31 × 10⁻⁸ atm at 1400°, 1500°, and 1600°C, respectively. Analysis techniques that were used to determine the phase relations within the reacted samples included X-ray diffractometry, electron probe microanalysis (energy-dispersive spectroscopy and wavelength-dispersive spectroscopy), and optical microscopy. The solid-solution phases M₂O₃, M₃O₅, and higher Magneli phases (M _n O_{2 n −1}, where M = V, Ti) were identified in the V₂O₃–TiO₂ system. In the "V₂O₃–FeO" system, the solid-solution phases M₂O₃ and M₃O₄ (where M = V, Ti), as well as liquid, were identified.     

High-Strain-Rate Superplasticity in Y2O3-Stabilized Tetragonal ZrO2 Dispersed with 30 vol% MgAl2O4 Spinel

High-strain-rate superplasticity is attained in a 3-mol%-Y₂O₃-stabilized tetragonal ZrO₂ polycrystal (3Y-TZP) dispersed with 30 vol% MgAl₂O₄ spinel: tensile elongation at 1823 K reached >300% at strain rates of 1.7 × 10⁻²– 3.3 × 10⁻¹ s⁻¹. The flow behavior and the microstructure of this material indicate that the MgAl₂O₄ dispersion should enhance accommodation processes necessary for grain boundary sliding. Such an effect is assumed to arise from an enhancement of the cation diffusion by the dissolution of Al and Mg ions into the ZrO₂ matrix and from stress relaxation due to the dispersed MgAl₂O₄ grains.     

In Situ Reaction Synthesis, Electrical and Thermal, and Mechanical Properties of Nb4AlC3

In this work, a bulk Nb₄AlC₃ ceramic was prepared by an in situ reaction/hot pressing method using Nb, Al, and C as the starting materials. The reaction path, microstructure, physical, and mechanical properties of Nb₄AlC₃ were systematically investigated. The thermal expansion coefficient was determined as 7.2 × 10⁻⁶ K⁻¹ in the temperature range of 200°–1100°C. The thermal conductivity of Nb₄AlC₃ increased from 13.5 W·(m·K)⁻¹ at room temperature to 21.2 W·(m·K)⁻¹ at 1227°C, and the electrical conductivity decreased from 3.35 × 10⁶ to 1.13 × 10⁶Ω⁻¹·m⁻¹ in a temperature range of 5–300 K. Nb₄AlC₃ possessed a low hardness of 2.6 GPa, high flexural strength of 346 MPa, and high fracture toughness of 7.1 MPa·m^1/2. Most significantly, Nb₄AlC₃ could retain high modulus and strength up to very high temperatures. The Young's modulus at 1580°C was 241 GPa (79% of that at room temperature), and the flexural strength could retain the ambient strength value without any degradation up to the maximum measured temperature of 1400°C.     

Fabrication and Electrical Properties of Textured Sr0.53Ba0.47Nb2O6 Ceramics by Templated Grain Growth

Textured Sr_0.53Ba_0.47Nb₂O₆ ceramics with a relative density of >95% were fabricated using templated grain growth (TGG). Acicular KSr₂Nb₅O₁₅ template particles synthesized via a molten salt process were aligned by tape casting in a mixture of solid-state-synthesized SrNb₂O₆ and BaNb₂O₆ powders. The resulting ceramics possessed strong fiber texture along the polar axis ([001]) of the strontium barium niobate. Samples with 15.4 wt% templates attained a textured fraction of 0.82 after sintering at a temperature of 1450°C for 4 h. These materials showed peak dielectric constants of 7550 at 1 kHz, remanent polarizations of 13.2 μC/cm², saturation polarizations of 21 μC/cm² (60%–85% of the single-crystal value), piezoelectric strain coefficients of 78 pC/N (70%–85% of the single-crystal value), and room-temperature pyroelectric coefficients of 2.9 × 10⁻²μC·(cm²·°C)⁻¹ (52% of the single-crystal value). These results show that TGG is a viable option for accessing single-crystal properties in polycrystalline ceramics.     

Structure of Liquid Al6Si2O13 (3:2 Mullite)

We report the first measurements of the structure factor, S ( Q ), and the pair distribution function, G ( r ), of Al₆Si₂O₁₃ (3:2 mullite) in the normal and supercooled liquid states in the temperature range 1776–2203 K. Measurements are obtained by synchrotron X-ray scattering on levitated, laser-heated liquid specimens. The S ( Q ) shows a prepeak at 2.0 Å⁻¹ followed by a main peak at 4.5 Å⁻¹ and a weak feature at 8 Å⁻¹. The G ( r ) shows a strong (Si,Al)–O correlation at 1.80 Å at high temperature that moves to 1.72 Å as the liquid is supercooled. The second and third nearest neighbor peaks at 3.0 and 4.25 Å sharpen with supercooling. The short-range structure of the high-temperature liquid is similar to the corresponding glasses produced by rapid quenching. Supercooling causes an increase in the concentration of tetrahedral Si⁴⁺ ions, which is manifested by the large shift in the first peak to lower ionic distance, r , values in G ( r ). The increase in tetrahedrally coordinated Si⁴⁺ ions is offset by an increase in octahedral Al³⁺ ions. The clustering of the SiO₄⁴⁻ tetrahedral units results in increased viscosity of the liquid at temperatures below the melting point, which is consistent with Al₆Si₂O₁₃ being a fragile liquid.     

Large Pyroelectric Effect in Relaxor-Based Ferroelectric Pb(Mg1/3Nb2/3)O3–PbTiO3 Single Crystals

The pyroelectric properties of (1− x )Pb(Mg_1/3Nb_2/3)O_{3− x} PbTiO₃ (PMN− x PT) single crystals with various compositions and orientations have been investigated using a dynamic method. Excellent pyroelectric performances can be achieved in 〈111〉-oriented rhombohedral PMN− x PT (0.24≤ x ≤0.30) crystals, where the measurement direction corresponds to the polar axis of the crystal. At room temperature, the pyroelectric coefficient and the detectivity figure of merit ( F _d ) for the 〈111〉-oriented PMN–0.28PT single crystal are 8.55 × 10⁻⁴ C·(m²·K)⁻¹ and 9.89 × 10⁻⁵ Pa^−1/2 (100 Hz), respectively, superior to those of the widely used pyroelectric materials. They are also weak temperature dependent and nearly independent of frequency. These outstanding pyroelectric performances make the single crystals a promising candidate for uncooled infrared detectors and thermal imagers.     

Strength of Hot Isostatically Pressed Si3N4 After Heat Treatment in Ar-O2 and H2-H2O

The effects of heat treatment in Ar-O₂ and H₂-H₂O atmospheres on the flexural strength of hot isostatically pressed Si₃N₄ were investigated. Increases in room-temperature strength, to values significantly above that of the aspolished material, were observed when the Si₃N₄ was exposed at 1400°C to (1) H₂ with water vapor pressure ( P _H2O) greater than 1 × 10⁻⁴ MPa or (2) Ar with oxygen partial pressure ( P _O2) of between 7 × 10⁻⁶ and 1.5 × 10⁻⁵ MPa. However, the strength of the material was degraded when the P _H2O in H₂ was lower than 1 × 10⁻⁴ MPa, and essentially unaffected when the P _O2 in Ar was higher than 1.5 × 10⁻⁵ MPa. We suggest that the observed strength increases are the result of strength-limiting surface flaws being healed by a Y₂Si₂O₇ layer formed during exposure.     

Characterization of the Thermally Contracting Tungstates Ta22W4O67, Ta2WO8, and Ta16W18O94

An investigation of the properties of high-purity (>99 wt%) tantalum tungstates (Ta₂₂W₄O₆₇, Ta, WO₈, and Ta₁₆W₁₈O₉₄) included determination of density (bulk and theoretical), refined lattice constants, maximum use temperatures, micro-hardness, heat capacity, thermal expansion (contraction) and diffusivity, calculated thermal conductivity, and electrical resistivity. Usable to ∼ 1700 K in air or inert atmospheres, these tantalum tungstates have theoretical densities of 7.3 to 8.5 g/cm³, are relatively soft (120 to 655 kg/mm² hardnesses), and are electrical insulators (6× 10³ to 2× 10⁸Ω^.cm resistivities). The distinguishing properties of the materials are their thermal expansion (average CTE values from + 0.6×10⁻⁸/K to −5.1× 10⁻⁶/K at 293 to 1273 K), thermal expansion hysteresis with minimal observable microcracking, and thermal diffusivity     

Thermal Expansion of SrY2O4

Crystals of SrY₂O₄ (space group Pnam ) were examined by high-temperature powder X-ray diffractometry to determine the changes in unit-cell dimensions with temperature. The individual cell dimensions linearly increased with increasing temperature up to 1473 K. The expansion coefficients (K⁻¹) were 1.263(8) × 10⁻⁵ along the a- axis, 7.46(6) × 10⁻⁶ along the b- axis, and 9.93(10) × 10⁻⁶ along the c- axis. The coefficient of mean linear expansion was 1.001(8) × 10⁻⁵ K⁻¹.     

Crystallization and Properties of Fe2O3—CaO—SiO2 Glasses

Nucleation and crystal growth rates and properties were studied in a two-stage heat treatment process for Fe₂O₃-CaO-SiO₂ glasses. Glass transition (T_g) and crystallization temperatures (T _c ) for the glasses lay between about 612.0° and 710.0°C, and 858.5° and 905.0°C, respectively, and magnetite was the main crystal phase. For a glass of 40Fe₂O₃. 20CaO·40SiO₂ (in wt%) the maximum nucleation rate was (68.6 ± 7) × 10⁶/mm³·s at 700°C, and the maximum crystal growth rate was 9.0 nm/min^1/2 at 1000°C. The mean crystal size of the magnetite increased from 30 to 140 nm with variation of nucleation and crystal growth conditions. The glass showed the maxima in saturation magnetization and coercive force, 212.1 × Wb/m² and 30.8 × 10³ A/m, when heat-treated for 4 h at 1000°C and 1050°C, respectively. The variation of the saturation magnetization could be quantitatively interpreted well in terms of the volume fraction of the magnetite, whereas that of the coercive forces could be explained only qualitatively in terms of the particle size of the magnetite. Hysteresis losses showed the maximum value of 1493 W/m³ when heat-treated at 1000°C for 4 h prenucleated at 700°C for 60 min, and increased linearly with increasing heat treatment time under a magnetic field up to 800 × 10³ A/m.     

Thermal Expansion of Pb3O4

Thermal expansion of Pb₃O₄ was investigated by high-temperature X-ray diffraction. The coefficient in the a ₀ direction is 14.6×10⁻⁶/°C. Expansion in the c₀ direction is 32% greater, with a coefficient of 19.3×10⁻⁶/°C. Coefficients of expansion are linear from 25° to 490°C and are comparable with those of tetragonal and orthorhombic PbO.